SIDAC K Series Silicon Bilateral Voltage Triggered Switch n Features n General Description l AC circuit oriented l Glass-passivated junctions l High surge current capability The sidac is a silicon bilateral voltage triggered switch with greater power-handling capabilities than standard diacs. Upon application of a voltage exceeding the sidac breakover voltage point, the sidac switches on through a negative resistance region to a low on-state voltage. Conduction continues until the current is interrupted or drops below the minimum holding current of the device. CERAMATE offers a voltage range of 95 V to 330 V in DO-15 package. n Applications l High voltage lamp ignitors l Natural gas ignitors l Gas oil ignitors l High voltage power supplies l Xenon ignitors l Over voltage protector l Pulse generators l Fluorescent lighting ignitors l HID surge current capability CERAMATE’s sidacs feature glass passivated junctions to ensure a rugged and dependable device capable of withstanding harsh environments. Variations of devices covered in this data sheet are available for custom design applications. Consult the factory for more information. n Electrical Characteristics VBO VDRM Breakover Voltage Part No (Instantaneous clamping voltage) K105 K110 K120 K130 K140 K150 K200 K220 K240 K250 K300 IDRM Blocking Voltage Peak Off-state Current at VDRM IT IH Continuous On-state Holding DC or RMS Current Current VTM Peak On-state Voltage IT =1A MIN (V) MAX (V) MIN (V) MAX (µA) MAX (A) MAX (mA) MAX (V) 95 104 110 120 130 140 190 205 220 240 270 113 118 125 138 146 170 215 230 250 280 330 75 85 90 95 105 115 150 165 175 190 215 10 10 10 10 10 10 10 10 10 10 10 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 100 100 100 100 100 100 100 100 100 100 100 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: [email protected] Tel:886-3-3214525 Http: www.ceramate.com.tw Page 1 of 2 Rev 1.1 Sep. 9,2002 Fax:886-3-3521052 SIDAC K Series Silicon Bilateral Voltage Triggered Switch Series K IPP ITSM di/dt Peak pulse current, TJ <150º C Peak one Cycle(sinusoidal) Surge Current Critical Rate of Rise of On-state Current (10×160µs) (10×560µs) (10×1000µs) Max (A) Max (A) Max (A) 60Hz (A) 60 35 35 20 50Hz (A) 16.7 TYPICAL (A/µs) 100 n V-I Characteristics n Package Dimensions K Series / DO-15 Ref Inches Min Max Millimeters Min Max A 1.0 25.4 B 0.22 0.30 5.60 7.60 C 0.028 0.035 0.70 0.90 D 0.10 0.15 2.60 3.80 * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: [email protected] Tel:886-3-3214525 Http: www.ceramate.com.tw Page 2 of 2 Rev 1.1 Sep. 9,2002 Fax:886-3-3521052