This product is not recommended for new designs. This specification is not being maintained. Some options may no longer be available and some information may be obsolete. VMIVME-4905 High Power Digital-to-Synchro/Resolver Converter Board • 14-bit converter with an accuracy as high as ±1 arc minute (±4 arc minutes is standard) • 3- or 4-wire output for driving synchros or resolvers • Internal transformers (400 Hz options) • Front panel fail LED • Amp D-type (no. 206584-1) • 5 VA, 2 VA (transformer output), or 0.024 VA options • Nonprivileged or supervisory short I/O • Supports off-line and on-line fault detection and isolation • Compatible with Intelligent I/O Controllers DESCRIPTION — The VMIVME-4905, a digital-to-synchro or resolver converter (DSC/DRC) board, utilizes the NATEL-HSDR 2514 converter module. It supports a wide variety of options which are supported by configuring jumpers on the basic printed circuit board and by installing optional parts (see the Ordering Options). The VMIVME-4905 board, with supported Built-in-Test VMIC hardware, features both offline and online fault detection and isolation. The Built-in-Test features require a VMIC quad-channel synchro-to-digital converter (SDC) board (VMIVME-4911) or a single channel SDC board (VMIVME-4910) and a standard synchro test backplane (SRTbus™) installed in the P2 position of a standard VME chassis (refer to VMIC’s Synchro/Resolver (Built-in-Test) Subsystem Configuration Guide, Document No. 825-000000-004). The board accepts a 14-bit digital output word (shaft angle), a reference excitation voltage, and produces a synchro or resolver output. The board is ideally suited for computer-based systems in which digital information is processed, such as simulators, robotics, and other control-oriented systems. The DSC/DRC is provided with several options and is capable of interfacing with most standard synchro or resolver devices. FUNCTIONAL CHARACTERISTICS Compatibility: VMEbus specification compatible. Double height form factor. Output Connector Type: AMP no. 206584-1 Output Organization: Two ports, 16 bits wide. Addressable to any address within short supervisory or short nonprivileged I/O map. Address Modifier Codes: Jumper selectable for short supervisory or short nonprivileged I/O access. Factory configured for short supervisory I/O access. Ordering Options September 12, 2000 800-004905-000 G VMIVME-4905 High Power Option for DSC/DRC Boards 1 with Built-in-Test* Ref. Input 2 Signal Output (RMS)*** Single 26 V ±10% 11.8 V Single 26 V ±10% Dual 26 V ±10% Dual or Single Board Output Type ABC Option No. 4** 2** 1.5** 1** DC to 1 K 5.0 Synchro 323 324 N/A 6.81 V DC to 1 K 5.0 Resolver 333 334 N/A 335 11.8 V DC to 1 K 5.0 Synchro 423 424 N/A 425 DC to 1 K 5.0 Resolver Freq. (Hz) 3 VA 325 Dual 26 V ±10% 6.81 V 433 434 N/A 435 Single 26 V ±10% 11.8 V 400 2.0 Synchro w/ 746 N/A N/A Trans. N/A Dual 26 V ±10% 11.8 V 400 2.0 Synchro w/ 846 N/A N/A Trans. N/A Single 40 V ±10% 40 V ±14% 512 2.0 Resolver w/ 556 N/A N/A Trans. N/A Dual 40 V ±10% 40 V ±14% 512 2.0 Resolver w/ 656 N/A N/A Trans. N/A * Built-in-Test requires one synchro/resolver-to-digital converter board for wrap-back testing of the digital-to-synchro/resolver converter board. Refer to the VMIC Synchro/Resolver (Built-in-Test) Subsystem Configuration Guide (Document No. 825-000000-004) for a detailed discussion. ** Reference to accuracy 4 = ±4 arc minutes (standard stock item) 2 = ±2 arc minutes (long lead time is typical) 1.5 = ±1.5 arc minutes (long lead time is typical) 1 = ±1 arc minute (long lead time is typical) *** Contact VMIC for availability of transformer-coupled outputs and higher voltages. Notes 1. All synchro/resolver boards require external ±15 V power supplies. Power and reference inputs can be connected to P2 or P3 (front panel). Power input connectors are available on VMIC's synchro/resolver backplane (SRTbus). 2. The reference input voltage can be jumper-selectable (by the user) for 1.3, 26, or 115 VRMS. Contact VMIC for other reference input voltages. 3. To 10 kHz with reduced accuracy. Connector Data Addressing Scheme: Two ports individually addressable on 8- or 16-bit boundaries. Two eight-position DIP switches provide unlimited short data I/O address map selection. Compatible Cable Connector Strain Relief Kit PC Board Header Connector VMIC • 12090 South Memorial Parkway • Huntsville, Alabama 35803-3308 AMP 747322-2 Type D AMP 206584-1 For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859 E-mail: [email protected] Web Address: www.vmic.com Copyright © January 1986 by VMIC Specifications subject to change without notice. 1 VMIVME-4905 Power Requirements: 5 and 2 VA Options +5 V at 2 A +15 V at 2.6 A4 -15 V at 2.6 A4 Ordering Options September 12, 2000 800-004905-000 G VMIVME-4905 Low Power Option for DSC/DRC Boards 1 with Built-in-Test* Board Output Type Dual or Single Ref. Input 2 Signal Output (RMS)*** Single 26 V ±10% 11.8 V DC to 1 K .024 Synchro 320 321 N/A 322 Single 26 V ±10% 6.81 V DC to 1 K .024 Resolver 330 331 N/A 332 Dual 26 V ±10% 11.8 V DC to 1 K .024 Synchro 420 421 N/A 422 Dual 26 V ±10% 6.81 V DC to 1 K .024 Resolver 430 431 N/A 432 Freq. (Hz) 3 VA Option No. 4** 2** 1.5** 1** Single 5 V ±8% 11.8 V DC to 1 K .024 Synchro 300 301 N/A 302 Single 5 V ±8% 6.81 V DC to 1 K .024 Resolver 310 311 N/A 312 Dual 5 V ±8% 11.8 V DC to 1 K .024 Synchro 400 401 N/A 402 Dual 40 V ±8% 6.81 V DC to 1 K .024 Resolver 410 411 N/A 412 * Built-in-Test requires one synchro/resolver-to-digital converter board for wrap-back testing of the digital-to-synchro/resolver converter board. Refer to the VMIC Synchro/Resolver (Built-in-Test) Subsystem Configuration Guide (Document No. 825-000000-004) for a detailed discussion. ** Reference to accuracy 4 = ±4 arc minutes (standard stock item) 2 = ±2 arc minutes (long lead time is typical) 1.5 = ±1.5 arc minutes (long lead time is typical) 1 = ±1 arc minute (long lead time is typical) *** Line-to-Line voltage for synchro outputs. Notes 1. All synchro/resolver boards require external ±15 V power supplies. Power and reference inputs can be connected to P2 or P3 (front panel). Power input connectors are available on VMIC's synchro/resolver backplane (SRTbus). 2. The 26 V reference input can be jumper-selectable (by the user) for 1.3, 26, or 115 VRMS. Contact VMIC for other reference input voltages. 3. To 10 kHz with reduced accuracy. Connector Data Compatible Cable Connector Strain Relief Kit PC Board Header Connector AMP 747322-2 Type D AMP 206584-1 For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859 E-mail: [email protected] Web Address: www.vmic.com Copyright © January 1986 by VMIC Specifications subject to change without notice. Fail LED: A front panel Fail LED (red) is provided that is illuminated at power up and extinguished under program control upon successful completion of user-defined diagnostics. Low Power Options +5 V at 2 A +15 V at 50 mA4 -15 V at 50 mA4 Notice — If this board is used with VMIC’s Intelligent I/O Controller (IIOC) product line (VMIVME-9015, -9016A, -9017, -9027, -9065, -9066, -9067, and -9068), a quad-channel S/D board (VMIVME-4911) and SRTbus is required for Built-in-Test. The IIOC firmware is not compatible with the VMIVME-4910. Built-in-Test DESCRIPTION — The VMIVME-4905 supports fault detection and isolation when used with the VMIC SRTbus and the model VMIVME-4911. The SRTbus is a synchro/resolver test bus that utilizes the user I/O pins on the P2 VMEbus connector. Programming the proper control bits in each output word of the VMIVME-4905 allows field disconnect and/or real-time loopback testing via the SRTbus and the VMIVME-4911. The user should refer to the VMIVME-4905 functional block diagram and the synchro/resolver (Built-in-Test) Subsystem Configuration Guide for a thorough understanding of the Built-in-Test operation. Notice — The VMIVME-4905 is an enhanced version of the VMIVME-4900 series with different programming requirements. The VMIVME-4905 is not software compatible with the VMIVME-4900 series. Caution — When driving instruments with one or more phase connections grounded, transformer isolation is required. 4. External ±15 V power supply required. PHYSICAL/ENVIRONMENTAL Temperature Range: 0 to +55 °C, operating -20 to +85 °C, storage Relative Humidity Range: 20 to 80 percent, noncondensing Cooling: Forced air cooling is required for the 5 and 2 VA options 2 For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859 VMIVME-4905 Figure 1. VMIVME-4905 Digital-to-Synchro/Resolver Functional Block Diagram APPLICATION AND CONFIGURATION GUIDES — The following instruction manuals and configuration guides are available from VMIC to assist the user in the selection, specification, and implementation of systems based on VMIC’s products. Title Document No. Digital-to-Synchro/Resolver Converter Board Instruction Manual Synchro/Resolver-to-Digital Input Board with Built-in-Test Instruction Manual Digital-to-Synchro/Resolver Converter Output Board Instruction Manual 500-004905-000 500-004911-000 500-004900-000 TRADEMARKS SRTbus is a trademark and the VMIC logo is a registered trademark of VMIC. Other registered trademarks are the property of their respective owners. VMIC • 12090 South Memorial Parkway • Huntsville, Alabama 35803-3308 3