MIRROR WITH STAINLESS STEEL CHANNEL FRAME AND SHELF B-166 SERIES SNAP LOCKING DESIGN SCREW LOCKING DESIGN (Rear View) (Rear View) gg MM gg MM gg MM 3 3 gg MM 3 gg gg MM 3 MM g¿ÊOR4YP gg ORMM MM MM 3 4 Figure: 1 &RAME -IRROR -`iÊ6iÜ >VÊ*>ÌiÉ7>Ê>}iÀ STANDARD B-166 SERIES MIRRORS MODEL NO. B-166 1824 B-166 1830 B-166 1836 B-166 2436 3 Figure: 2 ,OCKING3CREW 0HILLIPS(EAD ALL OTHER SIZE MIRRORS OVERALL SIZE W H 18'' (46cm) 24'' (61cm) 18'' (46cm) 30'' (76cm) 18'' (46cm) 36'' (91cm) 24'' (61cm) 36'' (91cm) Designer’s Notes: 1. Special-order sizes available on request. 2. Maximum size mirror available, 24'' x 60'' (61 x 152cm); minimum size, 12" x 12" (30 x 30cm). Maximum shelf length is 24" (61cm). 3. All Bobrick framed mirror/shelf models are manufactured to overall width and height dimensions including shelf. EXAMPLE: A 24'' x 36'' (61 x 91cm) mirror will be furnished 24'' x 36'' (61 x 91cm) outside-of-frame to outside-of-frame including shelf. 4. To specify special sizes use Series Number followed by width then height in inches. EXAMPLE: B-166 2024. 5. Bobrick framed mirror/shelf models are manufactured to a tolerance ± 1/8'' (3.2mm). 6. For sufficient space to lift mirror onto wall hanger(s), provide 3-1/4'' (85mm) minimum clearance above center line of mounting screw holes. 7. Provide 1'' (25mm) minimum clearance at bottom of mirror for engaging locking screws and 1'' (25mm) clearance on each side. MATERIALS: Frame — Type 430 stainless steel, 1/2" x 1/2" x 3/8" (13 x 13 x 9.5mm) channel 1/4" (6mm) return at rear with bright polished finish. One-piece frame with 90 degree mitered corners. Galvanized steel back has integral horizontal hanging brackets near the top for hanging the mirror and near the bottom to prevent the bottom of the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger. In Screw Locking Design(see figure 2), concealed Phillipshead locking screws securely fasten mirror to wall hanger. Shelf — 18-8 S, type 304, 22-gauge (0.8mm) stainless steel with satin finish. 3/8" (10mm) return edges on front and sides with front edge hemmed for additional safety. Shelf is welded to mirror frame and reinforced by concealed 16-gauge (1.6mm) stainless steel brackets. No exposed rivet-heads, screws, or fasteners of any type appear on frame or shelf. Mirror — No. 1 quality, 1/4" (6mm) select float glass: selected for silvering, electrolytically copper-plated by the galvanic process, and guaranteed for 10 years against silver spoilage. Corners are protected by friction-absorbing filler strips; back is protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding. Concealed Wall Hanger — 20-gauge (9.0mm) galvanized steel. Incorporates lower support member, forming rigid rectangle, which engages lower backplate louvers to keep bottom of mirror against wall. continued . . . The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. Rev. 4506 R/B Printed in U.S.A. © 2006 by Bobrick Washroom Equipment, Inc. INSTALLATION: Mount wall hanger on wall with screws (furnished by manufacturer) at points indicated by an S. For plaster or dr y wall construction, provide backing to comply with local building codes, then secure wall hanger with screws furnished. When providing a concealed backing, allow backing to cover minimum range of mounting hole locations shown on drawing. For other wall surfaces, provide fiber plugs or expansion shields for use with screws furnished, or provide 1/8" (3mm) toggle bolts or expansion bolts. Hang mirror on wall hanger with all four backplate louvers engaged behind horizontal wall hanger members. To do this, mirror must be centered in front of the wall hanger horizontally, pressed flat against the wall approximately 1" (25mm) above final position and then lowered into final position. Snap Locking Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final position. Locking devices may be unlocked by inserting two flat blade screwdrivers behind each side of mirror near the bottom or under the bottom of the mirror and pulling mirror bottom for ward and then up (see figure 3). Screw locking Design — Lock mirror to wall hanger by tightening Phillips-head locking screws that are concealed in the bottom of frame by points indicated by a T. Mirror may be unlocked from wall hanger by loosening locking screws and lifting mirror off of concealed wall hanger (see figure 4). SNAP LOCKING DESIGN SCREW LOCKING DESIGN (Front View) (Front View) Approx. 1" (25mm) CL Approx. 1" (25mm) Initial Position CL Initial Position Final Position S Final Position S S S T T Figure: 3 Figure: 4 SPECIFICATION: Mirror shall have a one-piece type 430 stainless steel channel frame, 1/2" x 1/2" x 3/8" (13 x 13 x 9.5mm), with 90° mitered corners; all exposed surfaces shall have bright polished finish. Shelf shall be type 304, 22-gauge (0.8mm) stainless steel with satin finish and shall have 3/8" (10mm) return edges on front and sides with front return edge hemmed. Shelf shall be welded to mirror frame and reinforced by concealed stainless steel brackets. No rivet-heads, screws, or fasteners of any kind shall be exposed on frame or shelf. Select float glass mirror shall be guaranteed for 10 years against silver spoilage. Corners shall be protected by friction-absorbing filler strips and the back shall be protected by full-size, shock-absorbing, waterresistant, nonabrasive, 3/16" (5mm) thick polyethylene padding. Galvanized steel back shall have integral horizontal hanging brackets located at top and bottom for mounting on concealed rectangular wall hanger and to prevent the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger. Mirror shall be removable from wall. Framed Mirror With Shelf shall be Model B-166 _______________ (insert width and height) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom. The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. B-166 Rev. 5/06 R/B Printed in U.S.A. © 2006 by Bobrick Washroom Equipment, Inc.