ISSUED DATE :2003/08/02 REVISED DATE :2006/12/14E G J 111 7 A 1A Low Dropout Positive Adjustable or Fixed-Mode Regulator Description The GJ1117A is a low dropout at positive adjustable or fixed-mode regulator with minimum of 1A output current capability. The product is specifically designed to provide well-regulated supply for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply. GJ1117A is also well suited for other applications such as VGA cards. GJ1117A is guaranteed to have lower than 1.4V dropout at full load current making it ideal to provide well-regulated outputs of 1.25 to 5.0 with 6.4V to 12V input supply. Features 1.4Vmaximum dropout full load current Fast transient response Output current limiting Built-in thermal shutdown Good noise rejection 3-Terminal Adjustable or Fixed 1.5V,1.8V,2.5V,3.3V,5.0V Applications PC peripheral Communication Package Dimensions TO-252 REF. A B C D E F S Millimeter Min. Max. 6.40 6.80 5.20 5.50 6.80 7.20 2.40 3.00 2.30 REF. 0.70 0.90 0.60 0.90 REF. G H J K L M R Millimeter Min. Max. 0.50 0.70 2.20 2.40 0.45 0.55 0 0.15 0.90 1.50 5.40 5.80 0.80 1.20 Typical Circuit GJ1117A Page: 1/4 ISSUED DATE :2003/08/02 REVISED DATE :2006/12/14E Block Diagram Pin Descriptions Name I/O Adj (GND) Pin# 1 Vout O 2 Vin I 3 Function A resistor divider from this pin to the Vout pin and ground sets the output voltage (Ground only for fixed mode) The output of the regulator. A minimum of 10uF capacitor must be connected from this pin to ground to insure stability. The input pin of regulator. Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be 1.3V higher than Vout in order for the device to regulate properly. Absolute Maximum Ratings Symbol Parameter Vin DC Supply Voltage PD Power Dissipation TST Storage Temperature TOP Operating Junction Temperature Range TMJ Maximum Junction Temperature GJ1117A Ratings Unit -0.3 to 12 V Internally Limited -65 ~ + 150 0 ~ + 125 150 Page: 2/4 ISSUED DATE :2003/08/02 REVISED DATE :2006/12/14E Electrical Characteristics Parameter Reference Voltage Conditions MIN TYP MAX UNIT GJ1117AADJ Io=10mA, Tj=25 , (Vin-Vout )=1.5V 1.225 1.250 1.275 V GJ1117A-1.5 Io=10mA, Tj=25 , 3.0V Vin 12V 1.470 1.500 1.530 V GJ1117A-1.8 Io=10mA, Tj=25 , 3.3V Vin 12V 1.764 1.800 1.836 V GJ1117A-2.5 Io=10mA, Tj=25 , 4.0V Vin 12V 2.450 2.500 2.550 V GJ1117A-3.3 Io=10mA, Tj=25 , 4.8V Vin 12V 3.235 3.300 3.365 V GJ1117A-5.0 Io=10mA, Tj=25 , 6.5V Vin 12V 4.900 5.000 5.100 V GJ1117A-XXX Io=10mA, Vout+1.5V<Vin<12V, Tj=25 - - 0.2 % GJ1117AADJ Vin=3.3V, Vadj=0, 0mA<Io<1A, Tj=25 (Note 1,2) - - 1 % GJ1117A-1.5 Vin=3.0V, 0mA<Io<1A, TJ=25 (Note 1,2) - 12 15 mV GJ1117A-1.8 Vin=3.3V, 0mA<Io<1A, TJ=25 (Note 1,2) - 15 18 mV GJ1117A-2.5 Vin=4.0V, 0mA<Io<1A, TJ=25 (Note 1,2) - 20 25 mV GJ1117A-3.3 Vin=5.0V, 0mA<Io<1A, TJ=25 (Note 1,2) - 26 33 mV GJ1117A-5.0 Vin=8.0V, 0mA<Io<1A, TJ=25 (Note 1,2) - 40 50 mV Dropout Voltage (VIN-VOUT) GJ1117A-XXX Io=1A, ( Vout=0.1% Vout) - 1.3 1.4 V Current Limit GJ1117A-XXX Vin-Vout=5V 1.1 - - A Minimum Load Current Adjustable model Vin=5V - 5 10 mA Adjust Pin Current Adjustable model Vin=12V, Io=10mA - 50 100 uA Quiescent Current fixed model Vin=12V, Io=0mA - - 12 mA Thermal Regulation TA=25 ,30ms pulse - 0.008 0.04 %/W - 60 70 dB Output Voltage Line Regulation Load Regulation Ripple Rejection F=120HZ,COUT=25uF Tantalum, IOUT =1A GJ1117A-XXX VIN=VOUT +3V Temperature Stability IO=10mA 0.5 % JA Thermal Resistance Junction-to-Ambient(No 92 /W heat sink ;No air flow) JC Thermal Resistance Control Circuitry/Power Transistor 10 /W Junction-to-Case Note 1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction Temperature by low duty cycle pulse testing. Load regulation is measured at the output lead =1/18” from the package. Note 2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference in input and output and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. GJ1117A Page: 3/4 ISSUED DATE :2003/08/02 REVISED DATE :2006/12/14E Characteristics Curve Important Notice: All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of GTM. GTM reserves the right to make changes to its products without notice. GTM semiconductor products are not warranted to be suitable for use in life-support Applications, or systems. GTM assumes no liability for any consequence of customer product design, infringement of patents, or application assistance. Head Office And Factory: Taiwan: No. 17-1 Tatung Rd. Fu Kou Hsin-Chu Industrial Park, Hsin-Chu, Taiwan, R. O. C. TEL : 886-3-597-7061 FAX : 886-3-597-9220, 597-0785 China: (201203) No.255, Jang-Jiang Tsai-Lueng RD. , Pu-Dung-Hsin District, Shang-Hai City, China TEL : 86-21-5895-7671 ~ 4 FAX : 86-21-38950165 GJ1117A Page: 4/4