ETC HC49153020SR3RDBUT

QUARTZ CRYSTALS - Section Contents
Specifying Quartz Crystals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Stock Quartz Crystals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Watch Crystals 32.768kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cylinder Crystals (3 x 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CX-1 03 Crystals 10.0kHz to 2.1MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CX-1 Crystals 8.0 to 160.0MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
HC35 (TO5) Crystals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
UM5 & UM4 Crystals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
HC49/4H & HC49/3H Crystals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HC49 Crystals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
HC51 & HC47 Crystals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SC Cut Crystals: CFPX-2000 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
CFPX-3000 ESA/SCC Approved Quartz Crystals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
1
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
QUARTZ
CRYSTALS
UM1 Crystals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SPECIFYING QUARTZ CRYSTALS
A typical quartz crystal specification reads like this:
Frequency Tolerance
The cost of manufacture depends partly on the accuracy
required at the reference temperature (which in the case of
the AT-cut crystal, is usually 25°C).
35.0MHz HC49 15 30 20 SR 3RD BU T
Frequency
Holder Style
Where high initial accuracy is important the additional
manufacturing cost should be weighed against the cost of
including a frequency trimming facility within the oscillator.
Frequency Tolerance at 25°C
Frequency Stability
Frequency Stability
Lower end of Operating Temp Range
Frequency stability is normally specified as a frequency
tolerance over a defined operating temperature range with
respect to the frequency at reference temperature. The
temperature ranges are defined for each crystal in the
relevant data sheet. However the majority of crystals will
continue to operate quite satisfactorily outside the
temperature range for which they are specified, but with a
possible degradation of their frequency stability.
QUARTZ
CRYSTALS
Circuit Condition
Overtone order
Packaging
Additional Text Code (for non-standard product)
The following notes define each element of the specification.
Frequency
Generalised frequency vs temperature curves for the AT-cut
crystal types are illustrated in the following pages. These
indicate that, without compensation, a crystal specified for
operation over a wide frequency range will probably have an
inferior performance over a narrower range than one whose
design was optimised for the narrower range. The angle of
cut of the quartz blank from its quartz stone determines
which curve will be followed; the chosen angle being subject
to its own tolerance. Thus, since manufacturing cost is
tolerance-dependent it is wise not to specify a wider
operating temperature range than is actually needed unless
some sacrifice of stability, or an increase in cost, can be
accepted.
Frequency is normally specified in kilohertz (kHz) up to
999.999kHz and in megahertz (MHz) from 1.0MHz. All
our computer-generated transaction documents follow this
standard convention automatically.
The frequency should be given to seven significant figures. If
seven significant figures are not used, any figure that might
follow those given will be taken as zero. Thus a frequency
given as 16.6MHz will be taken as 16.60, not 16.66667.
Some specifiers extend the use of kHz to all crystals
operating in fundamental mode, reserving MHz for
overtones. To minimise the possibility of misunderstanding
it is best to use the standard method and specify the mode.
Standard Frequency Tolerances and Stabilities
Holder Style
n
Before manufacture of the crystal can start, the holder style
must be defined. If the holder size is not known or it is
unimportant, we will supply the holder normally adopted for
the frequency specified, such as HC49 for the majority of
microprocessor applications. The holder information should
also cover any mechanical variant required such as a top wire
or cropped leads. The following variants for example are
available for most crystals, either singly or in some cases, in
combination:
±5ppm, ±10ppm, ±15ppm, ±20ppm, ±30ppm,
±50ppm, ±100ppm
Operating Temperature Ranges
n
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
n
3 lead base
n
Top wire
n
Insulating sleeve
When the required temperature range is symmetrical about
25°C, it is indicated in the specification by the lower figure,
ie: –20 to 70°C would read ‘20’ as shown in the example. If
the required temperature range is not symmetrical about
25°C, both figures are used, ie: –55 to 85°C and appear in
the additional text code section (T).
n
Taped and reeled
Circuit condition
n
Fitted insulator
n
Cropped leads
n
Formed leads
The characters ‘SR’ are used to denote calibration of the
crystal at series resonance. If it is to be calibrated at load
resonance the characters represent the circuit load
capacitance in pF.
Packaging Codes
Tape & Reel packaging is available as an option on many of
the products outlined in the Quartz Crystal chapter.
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
2
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
Unless individual datasheets state Tape and Reel packaging,
items will be Bulk packed. Please note: only complete Reels
are sold.
BU = Bulk packed
n
1 0 .2 (0 .4 )
TR = Tape & Reel packed
Additional Text Code
S le e v e
If the product is non-standard, the letter ‘T’ will appear at
the end of the product specification. This refers to additional
text on the quotation/sales order to identify the special
requirements.
1 3 .4 6 m a x
(0 .5 3 m a x )
Æ 0 .4 5
Æ 0 .0 1 8
1 2 .7 m in
0 .5 m in
Outline Drawings
Dimensions on the crystal outline drawings are shown only
as a guide. Precise dimensions of crystal holders are available
from our Engineering Department upon request. All
dimensions are shown in mm (& inches) and are nominal
unless otherwise stated. All outlines are at a scale of 1:1
unless otherwise specified.
4 .8 8 (0 .1 9 2 )
4 .6 5 (0 .1 8 3 )
QUARTZ
CRYSTALS
n
Outline in mm (inches)- Insulated Sleeve HC49 &
HC43
1 1 .0 5
(0 .4 3 5 )
Marking
Product will be indelibly marked as detailed in the individual
data sheets. Where space is limited some or all of the
information will be omitted or truncated at CFP’s
discretion. Full product details will be found on the
individual batch packaging.
Outline in mm (inches)- HC49 with Top Wire
1 0 .2
(0 .4 0 1 )
Delivery Options
1 3 .4 6 m a x
(0 .5 3 m a x )
The following Express delivery options are available for
certain crystals; timescales refer to despatch from our
factories.
n
3 working days (Express service)
n
5 working days (Express service)
n
7 working days (Express service)
n
10 working days (Express service)
Æ 0 .4 5
(Æ 0 .0 1 8 )
5 .0 m in
(0 .1 9 7 m in )
S p o t- w e ld
1 2 .7 m in
(0 .5 m in )
4 .8 8 (0 .1 9 2 )
1 1 .0 5
(0 .4 3 5 )
Prices for larger quantities and longer delivery times are
g enera l l y l o w er d u e t o s ub s t a n t ia lly r e d u c e d
manufacturing costs. Please refer to individual datasheets
for further information.
4 .6 5 (0 .1 8 3 )
Outline in mm (inches)- Tape for HC49
Ordering Information
See individual datasheet
6 .3 5 ± 0 .7 (0 .2 5 ± 0 .0 2 8 )
Stability Conversion Chart
0.001
0.0000001
10–10
0.0001
0.00000001
Æ 4 .0 ± 0 .2
( Æ 0 .1 5 7 ± 0 .0 0 8 )
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
3
3 .8 5 ± 0 .7
(0 .1 5 ± 0 .0 3 )
1 2 .7 ± 0 .3
(0 .5 ± 0 .0 1 )
Americas Tel: +1 919 941 0430
7 .0 m in (0 .2 7 6 m in )
0.000001
10–9
)
0.00001
0.01
+ 0 .0 3 9
– 0 .0 2
0.1
10–8
(0 .7 0 9
10–7
+ 1 .0
– 0 .5
0.0001
1 8 .0
0.001
1
)
10
10–6
+ 0 .0 3
– 0 .0 3 9
0.01
(0 .3 5 4
100
10–5
+ 0 .7 5
– 0 .5
10–4
1 3 .5 m a x (0 .5 3 m a x )
%
9 .0
0.1
3 3 .3 6 m a x . (1 .3 1 3 m a x )
PPM
1000
1 8 .0 ± 2 .0 (0 .3 5 4 ± 0 .0 7 9 )
10x
10–3
1 .0 (0 .0 3 9 )
n
Æ 0 .4 5
(Æ 0 .0 1 8 )
0 .9 m a x
(0 .0 3 5 m a x )
Fax: +1 919 941 0530
STOCK QUARTZ CRYSTALS
Minimum Order Information Required
n
Frequency
Stock Number
QUARTZ
CRYSTALS
WATCH CRYSTALS
Frequency
Holder
Specification
Stock No.
32.7680kHz
3x8mm
20/-/-/12.5
A103A
32.7680kHz
3x8mm
15/-/-/12.5
A103B
32.7680kHz
2x6mm
20/-/-/12.5
A103C
40.0kHz
3x8mm
100/-/-/12.5
A109C
32.7680kHz
Holder
CX-1V
Specification
30/-/40/9
Holder
Specification
Stock No.
11.05920MHz
HC49/4H
30/50/20/30
L108K
12.0MHz
HC49/4H
30/50/20/30
A158K
12.288MHz
HC49/4H
30/50/10/30
A175K
14.31818MHz
HC49/4H
30/50/20/30
A153L
HC49/4H
30/50/10/30
A159K
15.0MHz
HC49/4H
30/50/10/30
A160K
15.36MHz
HC49/4H
20/30/10/30
M451K
16.0MHz
HC49/4H
30/50/20/30
A161K
Stock No.
16.9344MHz
HC49/4H
30/50/10/30
A213K
C513A
18.432MHz
HC49/4H
30/50/20/30
A146K
19.66080MHz
HC49/4H
30/50/10/30
A182K
20.0MHz
HC49/4H
30/50/20/12
A147K
Stock No.
20.0MHz
HC49/4H
30/50/10/20
A147L
24.0MHz
HC49/4H
30/50/10/30 Fund
A189K
HC49/4H CRYSTALS
Frequency
Specification
14.74560MHz
CX CRYSTALS
Frequency
Holder
3.27680MHz
HC49/4H
30/50/10/12
A118C
3.579545MHz
HC49/4H
30/50/20/20
A119K
24.576MHz
HC49/4H
30/50/10/20 Fund
A116K
HC49/4H
30/50/20/SR 3rd
A166K
3.68640MHz
HC49/4H
30/50/20/30
A169K
32.0MHz
4.0MHz
HC49/4H
20/50/10/30
A120K
35.2512MHz
HC49/4H
15/30/20/18 3rd
A216K
40.32MHz
HC49/4H
30/50/10/18 3rd
A220H
4.0MHz
HC49/4H
30/50/10/30
A120L
4.0MHz
HC49/4H
50/100/40/30
E120L
4.032MHz
HC49/4H
30/50/20/30
A121K
4.096MHz
HC49/4H
30/50/10/30
A122K
Frequency
Holder
Specification
Stock No.
UM-1
20/30/10/30
A170H
UM1 & HC45 CRYSTALS
4.194304MHz
HC49/4H
30/50/10/30
A123J
8.1920MHz
4.194304MHz
HC49/4H
30/50/10/12
A123K
8.1920MHz
UM-1
20/30/10/20
A170J
UM-1
20/30/10/30
A172H
4.433619MHz
HC49/4H
30/50/10/20
A124K
9.6000MHz
4.91520MHz
HC49/4H
30/50/20/30
A127K
10.2450MHz
UM-1
20/30/10/30
A155H
UM-1
20/30/10/30
A175H
5.0MHz
HC49/4H
30/50/10/30
A128K
12.2880MHz
5.76MHz
HC49/4H
30/50/10/30
L102K
14.31818MHz
UM-1
20/30/10/30
A153H
UM-1
20/30/10/30
A161H
6.0MHz
HC49/4H
30/50/10/30
A132K
16.0MHz
6.1440MHz
HC49/4H
30/50/10/30
A133K
16.3840MHz
UM-1
20/30/10/30
A178H
UM-1
20/30/10/20
A180J
7.37280MHz
HC49/4H
30/50/10/30
A194K
17.73447MHz
7.37280MHz
HC49/4H
15/30/10/18
A194L
17.73447MHz
UM-1
20/30/10/30
A180H
UM-1
20/30/10/20
A182J
7.3728OMHz
HC49/4H
30/50/20/18
A194M
19.66080MHz
7.86432MHz
HC49/4H
30/50/10/30
A139A
20.0MHz
UM-1
20/30/10/30
A147H
UM-1
20/30/10/20
A147J
UM-1
20/30/10/20 Fund
L111J
8.0MHz
HC49/4H
30/50/20/30
A140K
20.0MHz
8.192MHz
HC49/4H
30/50/10/30
A170K
22.248MHz
9.8304MHz
HC49/4H
30/50/10/30
A173K
10.0MHz
HC49/4H
30/50/20/30
A143K
10.752MHz
HC49/4H
30/50/10/30
A212K
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
4
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
Frequency
Holder
Specification
Stock No.
6.1440MHz
HC49
30/50/20/20 **
A133U
HC49
30/50/20/SR **
A133T
20/30/10/12
A135A
Frequency
Holder
Specification
Stock No.
6.1440MHz
1.84320MHz
HC49
20/50/10/30
A113B
6.55360MHz
HC49
1.84320MHz
HC49
20/50/10/SR
A113C
7.37280MHz
HC49
20/50/10/30
A194A
HC49
30/50/20/SR
A194D
2.0MHz
HC49
50/100/0/20
A114E
7.37280MHz
2.45760MHz
HC49
20/50/10/30
A116C
7.37280MHz
HC49
30/50/20/20 **
A194U
HC49
20/50/10/30
A138A
2.45760MHz
HC49
30/50/20/32 **
A116U
7.6800MHz
3.0MHz
HC49
20/50/10/30
A150B
8.0MHz
HC49
20/50/10/30
A140A
HC49
30/50/10/30
A140B
3.27680MHz
HC49
20/30/10/12
A118B
8.0MHz
3.579545MHz
HC49
20/50/10/20
A119C
8.0MHz
HC49
30/50/20/20 **
A140U
HC49
30/50/20/SR **
A140T
3.579545MHz
HC49
30/50/10/20
A119M
8.0MHz
3.579545MHz
HC49
30/50/20/18 **
A119U
8.192MHz
HC49
20/50/10/30
A170A
HC49
20/50/10/30
A141A
3.68640MHz
HC49
20/50/10/30
A169A
8.388608MHz
3.68640MHz
HC49
30/50/10/30
A169M
8.8672370MHz
HC49
30/30/10/20
A154A
HC49
20/50/10/30
A173A
3.68640MHz
HC49
30/50/20/20 **
A169U
9.83040MHz
3.68640MHz
HC49
30/50/20/SR **
A169T
10.0MHz
HC49
20/10/20/30
A143A
HC49
20/50/10/30
A143E
4.0MHz
HC49
20/10/20/30
A120A
10.0MHz
4.0MHz
HC49
20/50/10/30
A120B
10.0MHz
HC49
30/50/20/SR **
A143T
HC49
20/50/10/30
A144A
4.0MHz
HC49
30/50/10/30
A120N
10.70MHz
4.0MHz
HC49
30/50/20/20 **
A120U
10.7520MHz
HC49
20/30/10/30
A212A
HC49
20/30/10/30
A193A
4.0MHz
HC49
30/50/20/SR **
A120T
11.0MHz
4.032MHz
HC49
20/10/20/30
A121A
11.05920MHz
HC49
20/30/10/20
L108A
HC49
20/30/10/30
L108C
4.0960MHz
HC49
20/10/20/30
A122A
11.05920MHz
4.0960MHz
HC49
20/50/10/30
A122B
11.05920MHz
HC49
30/50/10/20
L108D
HC49
30/50/20/20 **
L108U
4.194304MHz
HC49
20/30/10/12
A123A
11.05920MHz
4.433619MHz
HC49
20/30/10/20
A124D
11.05920MHz
HC49
30/50/20/SR **
L108T
HC49
20/30/10/30
A214A
4.433619MHz
HC49
30/50/10/20
A124M
11.28960MHz
4.608MHz
HC49
20/50/10/30
A125C
12.0MHz
HC49
20/30/10/30
A158A
HC49
30/50/10/30
A158B
4.91520MHz
HC49
20/50/10/30
A127A
12.0MHz
4.91520MHz
HC49
30/50/10/30
A127B
12.0MHz
HC49
30/50/20/20 **
A158U
HC49
30/50/20/SR **
A158T
20/30/10/30
A175A
4.91520MHz
HC49
30/50/20/SR **
A127T
12.0MHz
5.0MHz
HC49
20/50/10/30
A128B
12.2880MHz
HC49
5.0MHz
HC49
30/50/20/20 **
A128U
12.2880MHz
HC49
30/50/20/20 **
A175U
HC49
30/50/20/SR **
A175T
5.06880MHz
HC49
20/50/10/SR
A129A
12.2880MHz
5.24288MHz
HC49
20/30/10/12
A186A
14.0MHz
HC49
20/50/10/30
A195A
HC49
20/50/10/SR
A153A
6.0MHz
HC49
20/50/10/30
A132A
14.31818MHz
6.0MHz
HC49
30/50/10/30
A132B
14.74560MHz
HC49
20/30/10/30
A159A
HC49
20/50/10/SR
A159B
6.0MHz
HC49
30/50/20/SR **
A132T
14.74560MHz
6.1440MHz
HC49
20/50/10/30
A133A
15.0MHz
HC49
20/50/10/SR
A160C
A133B
15.36MHz
HC49
20/30/10/30
M451A
16.0MHz
HC49
20/30/10/30
A161A
6.1440MHz
HC49
Europe Tel: +44 (0)1460 74433
20/50/0/12
Fax: +44 (0)1460 72578
5
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
QUARTZ
CRYSTALS
HC49 (HC43) CRYSTALS
Please note: Specifications followed by ** denote USA
specification.
QUARTZ
CRYSTALS
Frequency
Holder
Specification
Stock No.
16.0MHz
16.0MHz
HC49
30/50/10/30
A161N
HC49
30/50/20/20 **
A161U
16.0MHz
HC49
30/50/20/SR **
A161T
18.432MHz
HC49
30/50/20/20 **
A146U
18.432MHz
HC49
30/50/20/SR **
A146T
19.66080MHz
HC49
20/50/10/SR
A182A
19.66080MHz
HC49
30/50/10/18
A182C
20.0MHz
HC49
20/50/10/30
A147A
20.0MHz
HC49
20/30/10/SR
A147C
20.0MHz
HC49
30/50/10/30
A147D
20.0MHz
HC49
30/50/20/SR **
A147T
20.48MHz
HC49
30/50/10/30
A208B
22.11840MHz
HC49
20/50/10/SR Fund
A183A
22.5792MHz
HC49
10/20/10/15 Fund
A315A
24.0MHz
HC49
20/50/10/SR Fund
A189A
24.00014MHz
HC49
15/30/10/18 Fund
A210A
24.5760MHz
HC49
20/50/10/30 Fund
A223A
25.0MHz
HC49
20/50/10/SR Fund
A187B
32.0MHz
HC49
20/30/10/SR 3rd
A166A
32.0MHz
HC49
30/50/10/SR Fund
A166M
35.25120MHz
HC49
15/30/10/18/3rd
A216A
40.320MHz
HC49
15/30/10/18/3rd
A220A
Holder
Specification
Stock No.
2.0MHz
HC51
20/50/10/30
A114D
2.45760MHz
HC33
20/50/10/30
A116A
Description
For Holder
Stock No.
Insulators (Mylar, 3 holes)
UM1 (HC45)
M153C
Insulators (Mylar, 3 holes)
HC49
M153B
Insulator (PTFE, 2 holes)
HC49
M153D
Insulators (Mylar, 2 holes)
HC51 (HC33)
M154A
HC49
M156A
HC51 & HC33 CRYSTALS
Frequency
CRYSTAL ACCESSORIES
Clips
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
6
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
WATCH CRYSTALS 32.768kHz
ISSUE 9; 12 JUNE 1998
Outline in mm (inches) - (scale 3:1)
Delivery Options
6 .2 m a x
(0 .2 4 4 m a x )
Product available from stock. Please see p4 for details
Holder Style
n
Watch crystals are press sealed. Two sizes are available: 3 × 8.2mm & 2 × 6.2mm
n
Load Capacitance (CL): 6pF to 15pF
n
Drive Level: 1.0mW max.
n
Static Capacitance (C0): 1.6pF typical
0 .6 (0 .0 2 4 )
A c tu a l
S iz e
Æ 0 .3 5
(Æ 0 .0 1 4 )
1 0 .0
(0 .3 9 3 )
Æ 2 .0
(Æ 0 .0 7 9 )
Standard Frequency Tolerances and Stabilities
n
8 .2 m a x
(0 .3 2 3 m a x )
4 .0 m in
(0 .1 5 7 m in )
Æ 0 .2
(Æ 0 .0 0 8 )
General Specifications
A c tu a l
S iz e
QUARTZ
CRYSTALS
n
±20ppm, ±30ppm, ±50ppm, ±100ppm
Operating Temperature Ranges
n
0 to 50°C
–10 to 60°C
1 .1 (0 .0 4 3 )
–20 to 70°C
–30 to 80°C
Æ 3 .1 m a x .
(Æ 0 .1 2 2 m a x .)
Storage Temperature Range
n
–55 to 125°C
Frequency Temperature Curve
Marking
n
D f/f0
Frequency (3 × 8.2mm only; 2 × 6.2mm product is
unmarked)
(p p m )
Minimum Order Information Required
n
– 1 0 0
Frequency + Holder + Frequency Tolerance @ 25°C
+ Operating Temperature Range + Circuit Condition
m in
m a x
– 2 0 0
– 3 0 0
Df / f 0 = -0.038( T - T0 )2 ± 10%
– 4 0 0
T 0– 1 0 0
T o -5 0
T o + 5 0
2 5
T o
T o + 1 0 0
T (° C )
Electrical Specification – maximum limiting values
Frequency Range
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Frequency Stability Available Over
Operating Temperature
32.768kHz
±10ppm to ±100ppm
0 to 50°C
–25ppm
–100ppm
–10 to 60°C
–50ppm
–100ppm
–20 to 70°C
–85ppm
–100ppm
–30 to 80°C
–150ppm
–300ppm
Minimum
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
7
ESR
Max
Vibration
Mode
50kW
Fundamental
Maximum
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
CYLINDER CRYSTALS (3 x 9)
ISSUE 10; 26 MARCH 1998
Outline in mm (inches) - (scale 2:1)
Delivery Options
n
Please contact our sales office for current leadtimes
9 .0 m a x .
(0 .3 5 4 m a x )
Holder Style
n
3 × 9.0mm cylinder crystals are press sealed
A c tu a l
s iz e
General Specifications
QUARTZ
CRYSTALS
n
n
Load Capacitance (CL):
6pF to 15pF (15.0kHz to 2.70MHz)
10pF to 50pF or Series (3.57MHz to 60.0MHz)
1 0 .0
(0 .3 9 4 )
Æ 0 .3
(Æ 0 .0 1 2 )
Drive Level:
1.0mW max. (15.0kHz to 1.5360MHz)
5.0mW max. (1.70MHz to 2.70MHz)
500.0mW max. (3.570MHz to 60.0MHz)
Æ 3 .1
(Æ 0 .1 2 2 )
1 .1
Standard Frequency Tolerances and Stabilities
n
±10ppm, ±20ppm, ±30ppm, ±50ppm, ±100ppm,
±150ppm, ±200ppm, ±300ppm
Operating Temperature Ranges
n
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
Storage Temperature Range
n
–55 to 125°C
Marking
n
Frequency
Minimum Order Information Required
n
Frequency + Holder + Frequency Tolerance @ 25°C
+ Operating Temperature Range + Circuit Condition
Electrical Specification – maximum limiting values
Frequency Range
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Frequency Stability Available Over
Operating Temperature
15.0 to 150.0kHz
±20ppm to ±100ppm
0 to 50°C
–25ppm
–300ppm
–10 to 60°C
–50ppm
–300ppm
–20 to 70°C
–80ppm
–300ppm
–30 to 80°C
–120ppm
–300ppm
–40 to 90°C
–170ppm
–500ppm
0 to 50°C
±50ppm
±300ppm
–10 to 60°C
±100ppm
±300ppm
–20 to 70°C
±150ppm
±300ppm
–30 to 80°C
±200ppm
±300ppm
–40 to 90°C
±300ppm
±500ppm
0 to 50°C
±10ppm
±100ppm
Minimum
350.0kHz to 1.5360MHz
1.7 to < 2.7MHz
±50ppm to ±100ppm
±10ppm to ±100ppm
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
8
ESR
max.
Vibration
Mode
35kW
Fundamental
1.5kW
Fundamental
100W
Fundamental
Maximum
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
Frequency Range
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Frequency Stability Available Over
Operating Temperature
3.57 to < 3.7MHz
±30ppm to ±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±30ppm
±100ppm
–30 to 80°C
±40ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±30ppm
±100ppm
–30 to 80°C
±40ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±30ppm
±100ppm
–30 to 80°C
±40ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±30ppm
±100ppm
–30 to 80°C
±40ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±30ppm
±100ppm
–30 to 80°C
±40ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±30ppm
±100ppm
–30 to 80°C
±40ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±30ppm
±100ppm
–30 to 80°C
±40ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±30ppm
±100ppm
–30 to 80°C
±40ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
3.7 to < 4.0MHz
4.0 to < 5.0MHz
5.0 to < 10.0MHz
10.0 to < 16.0MHz
16.0 to < 26.0MHz
26.0 to < 36.0MHz
36.0 to 60.0MHz
±30ppm to ±100ppm
±30ppm to ±100ppm
±30ppm to ±100ppm
±30ppm to ±100ppm
±30ppm to ±100ppm
±30ppm to ±100ppm
±30ppm to ±100ppm
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
9
Vibration
Mode
200W
Fundamental
180W
Fundamental
200W
Fundamental
120W
Fundamental
50W
Fundamental
40W
Fundamental
100W
Fundamental
80W
Fundamental
Maximum
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
QUARTZ
CRYSTALS
Minimum
ESR
max.
CX-1-03 CRYSTALS 10.0kHz to 2.1MHz
ISSUE 6; 26 MARCH 1998
Storage Temperature Range
n
Delivery Options
n
Environmental Specification
Common frequencies are available from stock. Please
see p4 for details
Description
n
Statek’s CX-1,-1V, -1H crystals are high quality
chemically etched resonators manufactured with a
photolithographic process.
n
Shock: 1000g, 1.0ms ½ sine (< 614.4kHz)
n
Shock: 750g, 0.3ms ½ sine (530.0kHz to 2.1MHz)
n
Vibration: 20g, 10 to 2000Hz
Marking
n
The CX-1H version is a tuning fork resonator intended for use in simple series oscillators over the frequency range 10.0 to < 614.4kHz.
Minimum Order Information Required
n
n
The CX-1V versions are intended for use in simple
Pierce oscillators. They are tuning fork resonators
over the frequency range 10.0 to < 614.4kHz.
n
The CX-1 are length extensional resonators covering
the frequency range 530.0kHz to 2.1MHz.
8 .0 (0 .3 1 5 )
CX-1-03 crystals are housed in a ceramic package,
hermetically sealed, with a soft soldered glass lid &
leads.
3 .5 6 (0 .1 4 )
n
Static Capacitance (C0): 1.0pF to 2.0pF
n
Drive Level CX-1V type:
0.5mW max. (10.0 to < 25.0kHz)
1.0mW max. (25.0 to < 614.4kHz)
n
Drive Level CX-1 type:
3.0mW max. (530.0kHz to 2.1MHz)
n
Drive Level CX-1H type:
1.5mW max. (10.0 to < 25.0kHz)
3.0mW max. (25.0 to < 614.4kHz)
n
1 .7 8 (0 .0 7 )
0 .4 6
(0 .0 1 8 )
Frequency Temperature Curve (32.768kHz)
D f/f0
(p p m )
– 1 0 0
– 2 0 0
m in
Load Capacitance (CL) CX-1 type:
7pF (530.0kHz to 2.1MHz)
Other values available upon request
CX-1H type is calibrated at Series Resonance
Ageing: ±5ppm maximum first year
– 3 0 0
Operating Temperature Ranges
n
–10 to 70°C
=C
n
–40 to 85°C
= I
n
–55 to 125°C
=M
Europe Tel: +44 (0)1460 74433
0 .2 6 (0 .0 1 )
7 .6 2 (0 .3 )
Load Capacitance (CL) CX-1V type:
11pF (10.0 to < 16.0kHz)
10pF (16.0 to < 25.0kHz)
9pF (25.0 to < 55.0kHz)
8pF (55.0 to < 100.0kHz)
5pF (100.0 to < 180.0kHz)
4pF (180.0 to < 614.4kHz)
n
A c tu a l
S iz e
0 .5 1 (0 .0 2 )
4 .3 2
(0 .1 7 )
General Specifications
n
Frequency + Model + Terminations + Frequency
Tolerance @ 25°C + Operating Temperature Range +
Circuit Condition
Outline in mm (inches) - (scale 2:1)
Holder Style
n
Includes Frequency
m a x
QUARTZ
CRYSTALS
n
–55 to 125°C
Df / f 0 = -0.035( T - T0 )2 ± 10%
– 4 0 0
T 0– 1 0 0
Fax: +44 (0)1460 72578
10
T o -5 0
2 5
T o
Americas Tel: +1 919 941 0430
T o + 5 0
T o + 1 0 0
T (° C )
Fax: +1 919 941 0530
Electrical Specification – maximum limiting values
Frequency Range
*Frequency Tolerance
@ 25°C ±2°C
Operating Temperature Range
**ESR
max.
Vibration
Mode
10.0 to < 25.0kHz
A = ±30ppm
B = ±100ppm
C = ±1000ppm
–10 to 70°C
2.1MW
Tuning Fork
360kW
Tuning Fork
160kW
Tuning Fork
100kW
Tuning Fork
50kW
Tuning Fork
25kW
Tuning Fork
3kW
Extensional
50.0 to < 75.0kHz
75.0 to < 170.0kHz
170.0 to < 250.0kHz
250.0 to < 614.4kHz
530.0kHz to
2.1MHz ***
A = ±30ppm
B = ±100ppm
C = ±1000ppm
A = ±30ppm
B = ±100ppm
C = ±1000ppm
A = ±50ppm
B = ±100ppm
C = ±1000ppm
A = ±100ppm
B = ±200ppm
C = ±2000ppm
A = ±200ppm
B = ±500ppm
C = ±5000ppm
A = ±500ppm
B = ±1000ppm
C = ±10000ppm
–55 to 125°C
–10 to 70°C
–40 to 85°C
–55 to 125°C
–10 to 70°C
–40 to 85°C
–55 to 125°C
–10 to 70°C
–40 to 85°C
–55 to 125°C
–10 to 70°C
–40 to 85°C
–55 to 125°C
–10 to 70°C
–40 to 85°C
–55 to 125°C
–10 to 70°C
–40 to 85°C
–55 to 125°C
50kHz CX-1V 03 C C 9pF
Ordering Example
Frequency
Model No
Terminations
Frequency Tolerance @ 25°C
Operating Temperature Range: C = –10 to 70°C; I = –40 to 85°C; M = –55 to 125°C
Load Capacitance (Circuit Condition) - if non-standard
*Please note: other frequency tolerances are available on request.
** Above ESR values are for CX-1H only, CX-1V divide above values by 3.
*** Only CX-1 available
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
11
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
QUARTZ
CRYSTALS
25.0 to < 50.0kHz
–40 to 85°C
CX-1-03 CRYSTALS 8.0 to 160.0MHz
Outline in mm (inches) - (scale 2:1)
ISSUE 6; 26 MARCH 1998
8 .0 (0 .3 1 5 )
Delivery Options
n
3 .5 6 (0 .1 4 )
Please contact our sales office for current leadtimes
Description
n
4 .3 2
(0 .1 7 )
Statek’s CX-1-03 crystals are high quality chemically
etched resonators manufactured with a photolithographic process.
A c tu a l
S iz e
0 .5 1 (0 .0 2 )
0 .2 6 (0 .0 1 )
7 .6 2 (0 .3 )
1 .7 8 (0 .0 7 )
Holder Style
CX-1-03 crystals are housed in a ceramic package,
hermetically sealed, with a soft soldered glass lid &
leads.
0 .4 6
(0 .0 1 8 )
General Specifications
n
Load Capacitance (CL): 20pF
Other values available upon request
n
Static Capacitance (C0): 2.0 to 3.5pF
n
Drive Level: 500mW max
n
Ageing: ±5ppm max first year
Frequency Temperature Curve
+ 2 5
Standard Frequency Tolerances*
n
±100ppm, ±1000ppm, ±10000ppm
* Tighter tolerances available
D f/f0 (p p m )
QUARTZ
CRYSTALS
n
Operating Temperature Ranges
n
–10 to 70°C
=C
n
–40 to 85°C
= I
n
–55 to 125°C
=M
0
Storage Temperature Range
n
–55 to 125°C
– 2 5
Environmental Specification
(higher specification available on request)
n
Shock: 3000g, 0.3ms ½ sine
n
Vibration: 20g rms, 10 to 2000Hz random
– 5 0
– 2 0
+ 2 5
T e m p e ra tu re (° C )
+ 7 0
+ 1 0 0
Marking
n
Includes Frequency
Minimum Order Information Required
n
Frequency + Model + Terminations + Frequency
Tolerance @ 25°C + Frequency Stability + Operating
Temperature Range + Circuit Condition
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
12
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
Frequency Range
*Frequency Tolerance
@ 25°C ±2°C
Operating Temperature
Range
Minimum
Maximum
8.0 to < 9.0MHz
A = ±100ppm
B = ±1000ppm
C = ±10000ppm
–10 to 70°C
±10ppm
±100ppm
–40 to 85°C
±20ppm
±100ppm
–55 to 125°C
±30ppm
±300ppm
–10 to 70°C
±10ppm
±100ppm
–40 to 85°C
±20ppm
±100ppm
–55 to 125°C
±30ppm
±300ppm
–10 to 70°C
±10ppm
±100ppm
–40 to 85°C
±20ppm
±100ppm
–55 to 125°C
±30ppm
±300ppm
–10 to 70°C
±10ppm
±100ppm
–40 to 85°C
±20ppm
±100ppm
–55 to 125°C
±30ppm
±300ppm
–10 to 70°C
±10ppm
±100ppm
–40 to 85°C
±20ppm
±100ppm
–55 to 125°C
±30ppm
±300ppm
–10 to 70°C
±10ppm
±100ppm
–40 to 85°C
±20ppm
±100ppm
±30ppm
±300ppm
9.0 to < 11.0MHz
11.0 to < 14.0MHz
14.0 to < 20.0MHz
20.0 to 70.0MHz
48.0 to 160.0MHz
A = ±100ppm
B = ±1000ppm
C = ±10000ppm
A = ±100ppm
B = ±1000ppm
C = ±10000ppm
A = ±100ppm
B = ±1000ppm
C = ±10000ppm
A = ±100ppm
B = ±1000ppm
C = ±10000ppm
A = ±100ppm
B = ±1000ppm
C = ±10000ppm
–55 to 125°C
Frequency Stability Available Over
Operating Temperature
ESR
Max
Vibration
Mode
300W
Fundamental
AT cut
200W
Fundamental
AT cut
100W
Fundamental
AT cut
70W
Fundamental
AT cut
50W
Fundamental
AT cut
80W
3rd Overtone
10.0MHz CX-1 03 A 100ppm C 18pF
Ordering Example
Frequency
Model No
Terminations
Frequency Tolerance @ 25°C
Frequency Stability
Operating Temperature Range: C = –10 to 70°C; I = –40 to 85°C; M = –55 to 125°C
Load Capacitance (Circuit Condition) -if non-standard
*Please note: other frequency tolerances are available on request.
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
13
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
QUARTZ
CRYSTALS
Electrical Specification – maximum limiting values
HC35 (TO5) CRYSTALS
Outline in mm (inches)
ISSUE 9; 19 JUNE 1998
8 .5
(0 .3 3 5 )
Delivery Options
n
3 day Express Manufacturing Service, subject to piece
part stock availability
6 .6
(0 .2 6 )
Holder Style
n
Æ 0 .4 5
(Æ 0 .0 1 8 )
HC35 (TO5) crystals are resistance welded, hermetically sealed in an inert atmosphere with glass to metal
seals securing the lead wires
P in
1 . C
2 . C
3 . C
c o n n e c tio n s
ry s ta l
a s e & g ro u n d
ry s ta l
1
1 2 .0 m in
(0 .4 7 m in )
2
3
n
Load Capacitance (CL): 10pF to 75pF or Series
n
Drive Level: 1.0mW max.
n
Static Capacitance (C0): 7pF max.
n
Ageing: ±3ppm typical per year
1 0 .4
(0 .4 0 9 )
5 .0 8
(0 .2 )
Standard Frequency Tolerances and Stabilities
n
Typical Frequency vs Temperature Curves
for various angles of AT-cut crystals
±5ppm, ±10ppm, ±15ppm, ±20ppm, ±30ppm,
±50ppm, ±100ppm
+ 2 5
Operating Temperature Ranges
n
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
D f/f0 (p p m )
QUARTZ
CRYSTALS
General Specifications
Storage Temperature Range
n
–55 to 125°C
0
Environmental Specification
n
n
Shock: 981m/s2 for 6ms, three shocks in each direction along three mutually perpendicular planes
Vibration: 10 to 60Hz 0.75mm displacement, 60 to
2000Hz 98.1m/s2 acceleration, 30 minutes in each of
three mutually perpendicular planes
– 2 5
– 5 0
– 2 0
+ 2 5
T e m p e ra tu re (° C )
+ 7 0
+ 1 0 0
Marking
n
Includes Frequency
Minimum Order Information Required
n
Frequency + Holder + Frequency Tolerance @ 25°C
+ Frequency Stability + Operating Temperature
Range + Circuit Condition + Overtone Order
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
14
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
Electrical Specification – maximum limiting values
Frequency Range
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Frequency Stability Available Over
Operating Temperature
6.0 to < 8.0MHz
±5ppm to ±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
8.0 to < 15.0MHz
15.0 to 30.0MHz
25.0 to 90.0MHz
60.0 to 150.0MHz
125.0 to 175.0MHz
170.0 to 210.0MHz
±5ppm to ±100ppm
±5ppm to ±100ppm
±5ppm to ±100ppm
±5ppm to ±100ppm
±5ppm to ±100ppm
±5ppm to ±100ppm
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
15
Vibration
Mode
60W
Fundamental
AT cut
30W
Fundamental
AT cut
20W
Fundamental
AT cut
40W
3rd Overtone
AT cut
60W
5th Overtone
AT cut
100W
7th Overtone
AT cut
200W
9th Overtone
AT cut
Maximum
QUARTZ
CRYSTALS
Minimum
ESR
max.
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
UM1 CRYSTALS
Outline in mm (inches) - UM1 & UM1-3L
ISSUE 8; 15 JUNE 1998
7 .3
(0 .2 8 7 )
Delivery Options
n
Common frequencies are available from stock. Please
see p4 for details
n
3 day Express Manufacturing Service, subject to piece
part stock availability
Æ 0 .3 5
(Æ 0 .0 1 4 )
Holder Style
UM1 crystals are resistance welded, hermetically
sealed in an inert atmosphere with glass to metal seals
securing the lead wires
n
Holders suffixed ‘–3L have a centre third wire which
grounds the case
n
HC45 is not dimensionally identical to the UM1 but
for most purposes the two are interchangeable
Load Capacitance (CL): 10pF to 75pF or Series
n
Drive Level: 1mW max.
n
Static Capacitance (C0): 7pF max.
n
Ageing: ±3ppm typical per year
8 .0
(0 .3 1 5 )
1 2 .0 m in
Æ 0 .3 5
(0 .4 7 2 m in )
(Æ 0 .0 1 4 )
1 2 .0 m in
(0 .4 7 2 m in )
3 .2 (0 .1 2 6 )
8 .0
(0 .3 1 5 )
General Specifications
n
8 .0
(0 .3 1 5 )
3 .7 5 (0 .1 4 8 )
1 2 3
8 .0
(0 .3 1 5 )
3 .7 5 (0 .1 4 8 )
3 .2 (0 .1 2 6 )
P in
1 . C
2 . C
3 . C
c o n n e c tio n s
ry s ta l
a s e & G ro u n d
ry s ta l
Typical Frequency vs Temperature Curves
for various angles of AT-cut crystals
+ 2 5
Standard Frequency Tolerances and Stabilities
n
±5ppm, ±10ppm, ±15ppm, ±20ppm, ±30ppm,
±50ppm, ±100ppm
D f/f0 (p p m )
QUARTZ
CRYSTALS
n
7 .3
(0 .2 8 7 )
Operating Temperature Ranges
n
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
– 2 5
0
– 5 0
– 2 0
+ 2 5
T e m p e ra tu re (° C )
+ 7 0
+ 1 0 0
Storage Temperature Range
n
–55 to 125°C
Environmental Specification
n
n
Shock: 981m/s2 for 6ms, three shocks in each direction along three mutually perpendicular planes
Vibration: 10 to 60Hz 0.75mm displacement, 60 to
2000Hz 98.1m/s2 acceleration, 30 minutes in each of
three mutually perpendicular planes
Marking
n
Includes Frequency
Minimum Order Information Required
n
Frequency + Holder + Frequency Tolerance @ 25°C
+ Frequency Stability + Operating Temperature
Range + Circuit Condition + Overtone Order
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
16
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
Electrical Specification – maximum limiting values
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
6.0 to < 10.0MHz
±5ppm to ±100ppm
10.0 to < 15.0MHz
±5ppm to ±100ppm
15.0 to 30.0MHz
±5ppm to ±100ppm
25.0 to 90.0MHz
±5ppm to ±100ppm
60.0 to 150.0MHz
±5ppm to ±100ppm
125.0 to 175.0MHz
±5ppm to ±100ppm
175.0 to 250.0MHz
±5ppm to ±100ppm
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
Frequency Stability Available Over
Operating Temperature
Minimum
Maximum
±10ppm
±100ppm
±15ppm
±100ppm
±15ppm
±100ppm
±20ppm
±100ppm
±25ppm
±100ppm
±50ppm
±100ppm
±50ppm
±100ppm
±10ppm
±100ppm
±15ppm
±100ppm
±15ppm
±100ppm
±20ppm
±100ppm
±25ppm
±100ppm
±50ppm
±100ppm
±50ppm
±100ppm
±5ppm
±100ppm
±5ppm
±100ppm
±10ppm
±100ppm
±20ppm
±100ppm
±25ppm
±100ppm
±50ppm
±100ppm
±50ppm
±100ppm
±5ppm
±100ppm
±5ppm
±100ppm
±10ppm
±100ppm
±20ppm
±100ppm
±25ppm
±100ppm
±50ppm
±100ppm
±50ppm
±100ppm
±5ppm
±100ppm
±5ppm
±100ppm
±10ppm
±100ppm
±20ppm
±100ppm
±25ppm
±100ppm
±50ppm
±100ppm
±50ppm
±100ppm
±5ppm
±100ppm
±5ppm
±100ppm
±10ppm
±100ppm
±20ppm
±100ppm
±25ppm
±100ppm
±50ppm
±100ppm
±50ppm
±100ppm
±5ppm
±100ppm
±5ppm
±100ppm
±10ppm
±100ppm
±20ppm
±100ppm
±25ppm
±100ppm
±50ppm
±100ppm
±50ppm
±100ppm
17
ESR
max.
Vibration
Mode
80W
Fundamental
AT cut
60W
Fundamental
AT cut
30W
Fundamental
AT cut
45W
3rd Overtone
AT cut
100W
5th Overtone
AT cut
150W
7th Overtone
AT cut
200W
9th Overtone
AT cut
QUARTZ
CRYSTALS
Frequency Range
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
UM5 & UM4 CRYSTALS
Outline in mm (inches) - UM5 & UM5-3L
ISSUE 6; 12 JANUARY 1996
n
Please contact our sales office for current leadtimes
Holder Style
n
UM5 & UM4 crystals are resistance welded, hermetically sealed in an inert atmosphere with glass to metal
seals securing the lead wires
Æ 0 .3 5
(Æ 0 .0 1 4 )
Holders suffixed ‘–3L have a centre third wire which
grounds the case
Load Capacitance (CL): 10pF to 75pF or Series
n
Drive Level: 1mW max.
n
Static Capacitance (C0): 6pF max
n
Ageing: ±3ppm typical per year
3 .2 (0 .1 2 6 )
7 .8
(0 .3 0 7 )
7 .0
(0 .2 7 6 )
P in
1 . C
2 . C
3 . C
c o n n e c tio n s
ry s ta l
a s e & g ro u n d
ry s ta l
7 .0
(0 .2 7 6 )
4 .8
(0 .1 8 9 )
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
4 .8
(0 .1 8 9 )
1 2 .0 m in
(0 .4 7 2 m in )
Æ 0 .3 5
(Æ 0 .0 1 4 )
Æ 0 .3 5
(Æ 0 .0 1 4 )
3 .7 5 (0 .1 4 8 )
Storage Temperature Range
–55 to 125°C
7 .8
(0 .3 0 7 )
1 2 .0 m in
(0 .4 7 2 m in )
3 .7 5 (0 .1 4 8 )
3 .2 (0 .1 2 6 )
Environmental Specification
n
3 .7 5 (0 .1 4 8 )
Outline in mm (inches) - UM4 & UM4-3L
±5ppm, ±10ppm, ±15ppm, ±20ppm, ±30ppm,
±50ppm, ±100ppm
Operating Temperature Ranges
n
1 2 .0 m in
(0 .4 7 2 m in )
7 .8
(0 .3 0 7 )
Standard Frequency Tolerances and Stabilities
n
1 2 .0 m in
(0 .4 7 2 m in )
Æ 0 .3 5
(Æ 0 .0 1 4 )
3 .2 (0 .1 2 6 )
n
n
6 .0
(0 .2 3 6 )
1 2 3
General Specifications
n
6 .0
(0 .2 3 6 )
3 .7 5 (0 .1 4 8 )
1 2 3
7 .8
(0 .3 0 7 )
Shock: 981m/s2 for 6ms, three shocks in each direction along three mutually perpendicular planes
Vibration: 10 to 60Hz 0.75mm displacement, 60 to
500Hz 98.1m/s2 acceleration, 30 minutes in each of
three mutually perpendicular planes
3 .2 (0 .1 2 6 )
P in
1 . C
2 . C
3 . C
c o n n e c tio n s
ry s ta l
a s e & g ro u n d
ry s ta l
Typical Frequency vs Temperature Curves
for various angles of AT-cut crystals
+ 2 5
Marking
n
Includes Frequency
Minimum Order Information Required
n
Frequency + Holder + Frequency Tolerance @ 25°C
+ Frequency Stability + Operating Temperature
Range + Circuit Condition + Overtone Order
D f/f0 (p p m )
QUARTZ
CRYSTALS
n
7 .0
(0 .2 7 6 )
7 .0
(0 .2 7 6 )
Delivery Options
– 2 5
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
18
0
– 5 0
– 2 0
+ 2 5
T e m p e ra tu re (° C )
Americas Tel: +1 919 941 0430
+ 7 0
+ 1 0 0
Fax: +1 919 941 0530
Electrical Specification – maximum limiting values
Frequency Range
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Frequency Stability Available Over
Operating Temperature
10.0 to < 16.0MHz
±10ppm to ±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
16.0 to < 20.0MHz
20.0 to < 30.0MHz
30.0 to 40.0MHz
40.0 to 90.0MHz
70.0 to 150.0MHz
125.0 to 175.0MHz
±5ppm to ±100ppm
±5ppm to ±100ppm
±10ppm to ±100ppm
±5ppm to ±100ppm
±5ppm to ±100ppm
±5ppm to ±100ppm
Europe Tel: +44 (0)1460 74433
0 to 50°C
±10ppm
±100ppm
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
19
60W
Fundamental
AT cut
50W
Fundamental
AT cut
40W
Fundamental
AT cut
40W
Fundamental
AT cut
120W
3rd Overtone
AT cut
150W
5th Overtone
AT cut
150W
7th Overtone
AT cut
Maximum
–10 to 60°C
Fax: +44 (0)1460 72578
Vibration
Mode
QUARTZ
CRYSTALS
Minimum
ESR
max.
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
HC49/4H & HC49/3H CRYSTALS
Outline in mm (inches) - HC49/4H & HC49/4H-3L
ISSUE 8; 12 JUNE 1998
Delivery Options
n
4 .0 m a x *
(0 .1 5 7 m a x )
Common frequencies are available from stock. Please
see p4 for details
n
HC49/4H & HC49/3H crystals are resistance welded,
hermetically sealed in an inert atmosphere with glass
to metal seals securing the lead wires.
n
Holders suffixed ‘–3L have a centre third wire which
grounds the case
1 2 .7 m in
(0 .5 m in )
Æ 0 .4 5
(Æ 0 .0 1 2 )
= =
4 .8 8 (0 .1 9 2 )
1 2 3
4 .8 8 (0 .1 9 2 )
4 .6 5 (0 .1 8 3 )
1 1 .0 5
(0 .4 3 5 )
4 .6 5 (0 .1 8 3 )
1 1 .0 5
(0 .4 3 5 )
General Specifications
n
Load Capacitance (CL): 10pF to 75pF or Series
n
Drive Level: 500mW max.
n
Static Capacitance (C0): 7pF max.
n
Ageing: ±3ppm typical per year
* 4 .2 (0 .1 6 5 ) m a x fo r
fr e q u e n c ie s < 3 .0 M H z
c o n n e c tio n s
ry s ta l
a s e & g ro u n d
ry s ta l
Typical Frequency vs Temperature Curves
for various angles of AT-cut crystals
+ 2 5
Standard Frequency Tolerances and Stabilities
n
P in
1 . C
2 . C
3 . C
±10ppm, ±20ppm, ±30ppm, ±50ppm, ±100ppm
Operating Temperature Ranges
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
D f/f0 (p p m )
n
Storage Temperature Range
n
–55 to 125°C
0
Environmental Specification
n
n
Shock: 981m/s2 for 6ms, three shocks in each direction along three mutually perpendicular planes
– 2 5
Vibration: 10 to 60Hz 0.75mm displacement, 60 to
500Hz 98.1m/s2 acceleration, 30 minutes in each of
three mutually perpendicular planes
Frequency only
3 .0 m a x
(0 .1 1 8 m a x )
1 3 .2 m in
(0 .5 2 m in )
+ 2 5
T e m p e ra tu re (° C )
+ 7 0
+ 1 0 0
+ 1 0
0
Outline in mm (inches) - HC49/3H & HC49/3H-3L
Æ 0 .4 3
(Æ 0 .0 1 7 )
– 2 0
Typical Frequency vs Temperature Curves
for various angles of BT-cut crystals
Marking
n
– 5 0
3 .0 m a x
(0 .1 1 8 m a x )
Æ 0 .4 3
(Æ 0 .0 1 7 )
D f/f0 (p p m )
QUARTZ
CRYSTALS
1 2 .7 m in
(0 .5 m in )
Æ 0 .4 5
(Æ 0 .0 1 2 )
Holder Style
4 .0 m a x *
(0 .1 5 7 m a x )
1 3 .2 m in
(0 .5 2 m in )
– 5 0
= =
4 .8 8 (0 .1 9 2 )
1 2 3
4 .8 8 (0 .1 9 2 )
4 .6 5 (0 .1 8 3 )
1 1 .0 m a x
(0 .4 3 5 m a x )
Europe Tel: +44 (0)1460 74433
4 .6 5 (0 .1 8 3 )
1 1 .0 m a x
(0 .4 3 5 m a x )
P in
1 . C
2 . C
3 . C
c o n n e c tio n s
ry s ta l
a s e & g ro u n d
ry s ta l
Fax: +44 (0)1460 72578
– 5 0
20
– 2 0
+ 2 5
T e m p e ra tu re (° C )
Americas Tel: +1 919 941 0430
+ 7 0
+ 1 0 0
Fax: +1 919 941 0530
Minimum Order Information Required
n
Frequency + Holder + Frequency Tolerance @ 25°C + Frequency Stability + Operating Temperature Range +
Circuit Condition + Overtone Order
Electrical Specification – maximum limiting values
Frequency Range
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Frequency Stability Available Over
Operating Temperature
3.5 to <5.0MHz
±15ppm to ±100ppm
0 to 50°C
±15ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±20ppm
±100ppm
–30 to 80°C
±25ppm
±100ppm
–40 to 90°C
±30ppm
±100ppm
–55 to 105°C
±100ppm
±500ppm
5.0 to <8.0MHz
8.0 to <12.0MHz
12.0 to 25.0MHz
20.0 to 40.0MHz
25.0 to 70.0MHz
±15ppm to ±100ppm
±15ppm to ±100ppm
±15ppm to ±100ppm
Inclusive with Frequency
Stability
±15ppm to ±100ppm
Vibration
Mode
200W
Fundamental
AT cut
120W
Fundamental
AT cut
70W
Fundamental
AT cut
50W
Fundamental
AT cut
50W
Fundamental
BT cut
100W
3rd Overtone
AT cut
Maximum
0 to 50°C
±15ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±20ppm
±100ppm
–30 to 80°C
±25ppm
±100ppm
–40 to 90°C
±30ppm
±100ppm
–55 to 105°C
±100ppm
±500ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±50ppm
±100ppm
–10 to 60°C
±50ppm
±100ppm
–20 to 70°C
±100ppm
±100ppm
–30 to 80°C
±100ppm
±100ppm
0 to 50°C
±15ppm
±100ppm
–10 to 60°C
±20ppm
±100ppm
–20 to 70°C
±20ppm
±100ppm
–30 to 80°C
±25ppm
±100ppm
–40 to 90°C
±50ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
Please Note: Frequencies 3.0 to 3.5MHz are available; AT fundamentals are available up to 32.0MHz: please contact the sales office for more information.
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
21
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
QUARTZ
CRYSTALS
Minimum
ESR
max.
HC49 CRYSTALS
Outline in mm (inches) - HC49 & HC49-3L
ISSUE 8; 18 MAY 1998
1 0 .2 (0 .4 0 2 )
Delivery Options
n
n
Common frequencies are available from stock. Please
see p5 for details
1 3 .4 6 m a x
(0 .5 3 m a x )
3 day Express Manufacturing Service, subject to piece
part stock availability
Holder Style
QUARTZ
CRYSTALS
n
HC43 crystals are cold welded; HC43/T is truncated
version; HC42 is plug-in version
n
Holders suffixed ‘–3L have a centre third wire which
grounds the case; this is not applicable to the HC50
and HC42
n
Truncated versions are only available in the frequency
range 4.0 to 300.0MHz
Load Capacitance (CL): 10pF to 75pF or Series
n
Drive Level: 1mW max.
n
Static Capacitance (C0): 7pF max.
n
Ageing: ±3ppm typical per year
= =
1 2 3
4 .6 5 (0 .1 8 3 )
4 .8 8 (0 .1 9 2 )
4 .6 5 (0 .1 8 3 )
1 1 .0 5
(0 .4 3 5 )
1 1 .0 5
(0 .4 3 5 )
P in
1 . C
2 . C
3 . C
c o n n e c tio n s
ry s ta l
a s e & g ro u n d
ry s ta l
Outline in mm (inches) - HC50 & HC42
1 3 .4 6 m a x
(0 .5 3 m a x )
Æ 1 .0 2
(Æ 0 .0 3 9 )
Standard Frequency Tolerances and Stabilities
6 .0 5 m in
(0 .2 3 8 m in )
4 .8 8 (0 .1 9 2 )
±5ppm, ±10ppm, ±15ppm, ±20ppm, ±30ppm,
±50ppm, ±100ppm
4 .6 5 (0 .1 8 3 )
Operating Temperature Ranges
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
1 2 .7 m in
(0 .5 m in )
1 0 .2
(0 .4 0 2 )
n
n
Æ 0 .4 5
(Æ 0 .0 1 2 )
4 .8 8 (0 .1 9 2 )
General Specifications
n
1 3 .4 6 m a x
(0 .5 3 m a x )
1 2 .7 m in
(0 .5 m in )
Æ 0 .4 5
(Æ 0 .0 1 2 )
HC49 crystals are resistance welded, hermetically
sealed in an inert atmosphere with glass to metal seals
securing the lead wires; HC49/T is truncated version;
HC50 is plug–in version
n
1 0 .2 (0 .4 0 2 )
1 1 .0 5
(0 .4 3 5 )
–40 to 90°C
–55 to 105°C
–55 to 125°C
Outline in mm (inches) - HC49/T & HC49/T-3L
Storage Temperature Range
n
1 0 .2 (0 .4 0 2 )
1 1 .1 m a x
(0 .4 3 7 m a x )
Environmental Specification
n
n
Shock: 981m/s2 for 6ms, three shocks in each direction along three mutually perpendicular planes
Vibration: 10 to 60Hz 0.75mm displacement, 60 to
500Hz 98.1m/s2 acceleration, 30 minutes in each of
three mutually perpendicular planes
1 2 .7 m in
(0 .5 m in )
Æ 0 .4 5
(Æ 0 .0 1 2 )
1 1 .0 5
(0 .4 3 5 )
Fax: +44 (0)1460 72578
22
1 2 .7 m in
(0 .5 m in )
Æ 0 .4 5
(Æ 0 .0 1 2 )
4 .6 5 (0 .1 8 3 )
Includes Frequency
Europe Tel: +44 (0)1460 74433
1 1 .1 m a x
(0 .4 3 7 m a x )
4 .8 8 (0 .1 9 2 )
Marking
n
1 0 .2 (0 .4 0 2 )
–55 to 125°C
= =
4 .8 8 (0 .1 9 2 )
1 2 3
4 .6 5 (0 .1 8 3 )
1 1 .0 5
(0 .4 3 5 )
Americas Tel: +1 919 941 0430
P in
1 . C
2 . C
3 . C
c o n n e c tio n s
ry s ta l
a s e & g ro u n d
ry s ta l
Fax: +1 919 941 0530
Minimum Order Information Required
n
Frequency + Holder + Frequency Tolerance @ 25°C + Frequency Stability + Operating Temperature Range +
Circuit Condition + Overtone Order
Typical Frequency vs Temperature Curves
for various angles of AT-cut crystals
Typical Frequency vs Temperature Curves
for various angles of BT-cut crystals
+ 2 5
+ 1 0
– 2 5
D f/f0 (p p m )
0
– 5 0
– 5 0
– 2 0
+ 2 5
T e m p e ra tu re (° C )
+ 7 0
QUARTZ
CRYSTALS
D f/f0 (p p m )
0
– 5 0
+ 1 0 0
– 2 0
+ 2 5
T e m p e ra tu re (° C )
+ 7 0
+ 1 0 0
Electrical Specification – maximum limiting values
Frequency Range
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Frequency Stability Available Over
Operating Temperature
1.8432 to < 3.0MHz
±5ppm to ±100ppm
0 to 50°C
±15ppm
±200ppm
–10 to 60°C
±20ppm
±200ppm
Minimum
3.0 to < 4.0MHz
4.0 to < 7.0MHz
7.0 to < 10.0MHz
±5ppm to ±100ppm
±5ppm to ±100ppm
±5ppm to ±100ppm
Europe Tel: +44 (0)1460 74433
±20ppm
±200ppm
–30 to 80°C
±25ppm
±200ppm
–40 to 90°C
±30ppm
±200ppm
–55 to 105°C
±50ppm
±200ppm
–55 to 125°C
±100ppm
±200ppm
0 to 50°C
±15ppm
±200ppm
–10 to 60°C
±20ppm
±200ppm
–20 to 70°C
±20ppm
±200ppm
–30 to 80°C
±25ppm
±200ppm
–40 to 90°C
±30ppm
±200ppm
–55 to 105°C
±50ppm
±200ppm
–55 to 125°C
±55ppm
±200ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±10ppm
±100ppm
23
Vibration
Mode
600W
Fundamental
AT cut
150W
Fundamental
AT cut
100W
Fundamental
AT cut
50W
Fundamental
AT cut
Maximum
–20 to 70°C
Fax: +44 (0)1460 72578
ESR
max.
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
Frequency Range
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Frequency Stability Available Over
Operating Temperature
7.0 to < 10.0MHz
±5ppm to ±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
Minimum
±5ppm to ±100ppm
QUARTZ
CRYSTALS
10.0 to 36.0MHz
20.0 to 45.0MHz
21.0 to 90.0MHz
45.0 to 135.0MHz
60.0 to 150.0MHz
90.0 to 225.0MHz
85.0 to 210.0MHz
Inclusive with Frequency
Stability
±5ppm to ±100ppm
Inclusive with Frequency
Stability
±5ppm to ±100ppm
Inclusive with Frequency
Stability
±5ppm to ±100ppm
Europe Tel: +44 (0)1460 74433
–40 to 90°C
±25ppm
±100ppm
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±50ppm
±100ppm
–10 to 60°C
±50ppm
±100ppm
–20 to 70°C
±100ppm
±100ppm
–30 to 80°C
±100ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±50ppm
±100ppm
–10 to 60°C
±50ppm
±100ppm
–20 to 70°C
±100ppm
±100ppm
–30 to 80°C
±100ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
0 to 50°C
±50ppm
±100ppm
–10 to 60°C
±50ppm
±100ppm
–20 to 70°C
±100ppm
±100ppm
–30 to 80°C
±100ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
24
Vibration
Mode
50W
Fundamental
AT cut
35W
Fundamental
AT cut
35W
Fundamental
BT cut
40W
3rd Overtone
AT cut
35W
3rd Overtone
BT cut
70W
5th Overtone
AT cut
70W
5th Overtone
BT cut
100W
7th Overtone
AT cut
Maximum
–55 to 105°C
Fax: +44 (0)1460 72578
ESR
max.
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Minimum
Maximum
125.0 to 300.0MHz
Inclusive with Frequency
Stability
0 to 50°C
±50ppm
±100ppm
–10 to 60°C
±50ppm
±100ppm
–20 to 70°C
±100ppm
±100ppm
–30 to 80°C
±100ppm
±100ppm
0 to 50°C
±5ppm
±100ppm
–10 to 60°C
±5ppm
±100ppm
–20 to 70°C
±10ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
–55 to 125°C
±50ppm
±100ppm
110.0 to 270.0MHz
±5ppm to ±100ppm
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
Frequency Stability Available Over
Operating Temperature
25
ESR
max.
Vibration
Mode
100W
7th Overtone
BT cut
150W
9th Overtone
AT cut
Americas Tel: +1 919 941 0430
QUARTZ
CRYSTALS
Frequency Range
Fax: +1 919 941 0530
HC51 & HC47 CRYSTALS
Outline in mm (inches) - HC51 & HC51-3L
ISSUE 8; 19 JUNE 1997
Delivery Options
n
n
Common frequencies are available from stock. Please
see p6 for details
19.43 max
(0.765 max)
3 day Express Manufacturing Service, subject to piece
part stock availability
Æ 0.76
(Æ 0.03)
n
HC51 crystals are resistance welded, hermetically
sealed in an inert atmosphere with glass to metal seals
securing the lead wires; HC48 is plug–in version
n
HC47 crystals are cold welded; HC36 is plug–in version
n
8.86
(0.349)
Holders suffixed ‘–3L have a centre third wire which
grounds the case; this is not applicable to the HC36
and HC48
Load Capacitance (CL): 10pF to 75pF or Series
n
Drive Level: 1mW max.
n
Static Capacitance (C0): 9pF max.
n
Ageing: ±3ppm typical per year
3
8.86
(0.349)
19.05 (0.75)
1 9 .4 3 m a x
(0 .7 6 5 m a x )
Æ 1 .2 7
(Æ 0 .0 5 )
Standard Frequency Tolerances and Stabilities
6 .0 5 m in
(0 .2 3 8 m in )
±10ppm, ±15ppm, ±20ppm, ±30ppm, ±50ppm,
±100ppm
1 2 .3 4 (0 .4 8 6 )
Operating Temperature Ranges
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
8 .8 6
(0 .3 4 9 )
1 9 .0 5 (0 .7 5 )
Typical Frequency vs Temperature Curves
for various angles of AT-cut crystals
Storage Temperature Range
n
2
1
Outline in mm (inches) - HC48 & HC36
n
n
12.34 (0.486)
Pin connections
1. Crystal
2. Case & ground
3. Crystal
19.05 (0.75)
General Specifications
n
Æ 0.76
(Æ 0.03)
12.7 min
(0.5 min)
12.34 (0.486)
–55 to 125°C
+ 2 5
Environmental Specification
n
n
Shock: 981m/s2 for 6ms, three shocks in each direction along three mutually perpendicular p lanes
Vibration: 10 to 60Hz 0.75mm displacement, 60 to
500Hz 98.1m/s2 acceleration, 30 minutes in each of
three mutually perpendicular planes
D f/f0 (p p m )
QUARTZ
CRYSTALS
Holder Style
Marking
n
0
Includes Frequency
Minimum Order Information Required
n
Frequency + Holder + Frequency Tolerance @ 25°C
+ Frequency Stability + Operating Temperature
Range + Circuit Condition + Overtone Order
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
– 2 5
26
– 5 0
– 2 0
+ 2 5
T e m p e ra tu re (° C )
Americas Tel: +1 919 941 0430
+ 7 0
+ 1 0 0
Fax: +1 919 941 0530
Electrical Specification – maximum limiting values
Frequency Range
Frequency Tolerance
@ 25°C ±2°C
Operating
Temperature Range
Frequency Stability Available Over
Operating Temperature
890.0kHz to < 1.5MHz
±10ppm to ±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
1.5 to < 2.5MHz
2.5 to < 3.5MHz
3.5 to < 7.0MHz
7.0 to < 12.0MHz
12.0 to 24.0MHz
9.0 to 30.0MHz
15.0 to 50.0MHz
±10ppm to ±100ppm
±10ppm to ±100ppm
±10ppm to ±100ppm
±10ppm to ±100ppm
±10ppm to ±100ppm
±10ppm to ±100ppm
±10ppm to ±100ppm
Europe Tel: +44 (0)1460 74433
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
0 to 50°C
±10ppm
±100ppm
–10 to 60°C
±15ppm
±100ppm
–20 to 70°C
±15ppm
±100ppm
–30 to 80°C
±20ppm
±100ppm
–40 to 90°C
±25ppm
±100ppm
–55 to 105°C
±50ppm
±100ppm
27
700W
Fundamental
AT cut
350W
Fundamental
AT cut
200W
Fundamental
AT cut
100W
Fundamental
AT cut
40W
Fundamental
AT cut
20W
Fundamental
AT cut
20W
3rd Overtone
AT cut
20W
5th Overtone
AT cut
Maximum
–20 to 70°C
Fax: +44 (0)1460 72578
Vibration
Mode
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
QUARTZ
CRYSTALS
Minimum
ESR
max.
SC CUT CRYSTALS: CFPX-2000 SERIES
ISSUE 1; 18 MAY 1998
QUARTZ
CRYSTALS
n
Frequency\Holder Range
The CFPX-2000 series of SC cut quartz resonators
are double rotated crystals that offer considerable advantages over single rotated AT or BT cuts for certain
applications. The term SC stands for “Stress Compensated” and it was the property of compensation for
thermal transient and planar stress effects that was
sought in its orginal development. The frequency/temperature characteristics of the SC cut are most suitable for oven controlled oscillator applications for
precision frequency control.
Frequency
Range
Mode
Holder
IEC Code
8.0 to 50.0MHz
Fundamental
30.0 to 150.0MHz
3rd Overtone
HC35/U (TO5)
HC45/U
DK
EB
5.0 to 20.0MHz
Fundamental
HC37/U (TO8)
DL
8.0 to 20.0MHz
3rd Overtone
1.5 to 10.0MHz
Fundamental
4.0 to 20.0MHz
3rd Overtone
HC40/U
HC36/U
DU, DM, DR
DN
Key Features:
n
Thermal transient compensation - fast warm up
n
Low frequency/temperature response slope suitable
for ovened applications
n
n
Smooth frequency/temperature characteristics reduce
coupled mode problems
n
n
Low thermal hysteresis
n
General Characteristics
Low acceleration sensitivity
n
Q factor > 1.2 million for 10MHz 3rd overtone crystal
n
n
Bump: IEC 68-2-29 Test Eb, 4000 ±10 bumps at
400m/ s2 (40gn) in each of three mutually perpendicular planes
n
Vibration: IEC 68-2-6 Test Fc Procedure B4
(MIL-STD-202 Method 204), Duration 12 hours, 10
to 55Hz 0.75mm D.A., 55 to 2000Hz 98m/s2 (10gn)
n
Shock: IEC 68-2-27 Test Ea, (MIL-STD-202
Method 213) ½ sine wave, 981m/s2 (100gn) 11ms, 6
shocks in each plane
n
Damp Heat: IEC 68-2-3 Test Ca (Steady State), Duration 56 days, recovery time 12 hours
n
Change of temperature: IEC 68-2-14 Test Na (Rapid
Change) (MIL-STD-202 Method 107), 10 cycles of
30 mintues duration each for -55/+125°C cycle
n
n
n
n
Material: Swept premium Q, low inclusion density
n
To determine your exact requirements please contact
our Applications Support Department
8 .5 m a x
(0 .3 3 5 m a x )
6 .6 m a x
(0 .2 6 0 m a x )
1 2 .7 m in
(0 .5 0 0 m in )
Æ 0 .4 /0 .4 8
(Æ 0 .0 1 6 /0 .0 1 9 )
Robustness of Termination: IEC 68-2-21 Test Ua
(Tensile or Thrust)(MIL-STD-202 Method 211), 10
Newtons (Tensile) or 20 Newtons (Thrust)
4 .9 3 /5 .2 3
(0 .1 9 4 /0 .2 0 6 )
Hermetic Seal: IEC 68-2-17 Test Qk (Fine Leak),
(MIL-STD-202 Method 112 Test condition C) and
IEC 68-2-17 Test Qc (Gross Leak) (MIL-STD-202
Method 112 Test condition D)
T a g p o s itio n
o r p re s e n c e
o p tio n a l
0 .8 7 m a x
(0 .0 3 4 m a x )
Marking: Heat cured epoxy or engraving
Fax: +44 (0)1460 72578
g - sensitivity: < 1 × 10-9/g typical for HC35, HC37 or
HC40
Outline in mm (inches) - HC35/U (TO5) DK (scale 1.5:1)
Solderability: IEC 68-2-20 Test Ta Method1 (Solder
Bath) (MIL-STD-202 Method 208), Temperature
235°C
Europe Tel: +44 (0)1460 74433
Q - factor: > 1.2 million for 10MHz 3rd overtone
Note: These holders employ 4-point mounting and are
recommended where low g - sensitivity is a requirement
Environmental Specification:
n
Ageing: < 5 × 10-9/day at 85°C (fundamental)
< 1 × 10-9/day at 85°C (3rd overtone)
Note: Tighter specifications available
Ageing as low as 1 × 10-10/day at 85°C (3rd overtone)
can be achieved
n
n
Turnover temperature: 50 to 85°C
105 to 125°C
28
1
2
3
Americas Tel: +1 919 941 0430
1 0 .7 m a x
(0 .4 2 1 m a x )
Fax: +1 919 941 0530
CFPX-2000 Series Outline Drawings
Outline in mm (inches) - HC40/U, DU, DM, DR
2 2 m a x (0 .8 6 6 m a x )
1 8 .1 6 m a x (0 .7 1 5 m a x )
C
Outline in mm (inches) - HC36/U, DN
7.65 max
(0.301 max)
T y p e : D U
T y p e : D M
T y p e : D R
1 2 .7 m in
(0 .5 m in )
0 .9 m a x
(0 .0 3 5 m a x )
4.45 min
(0.175 min)
19.75 max
(0.8 max)
1.22 min
(0.048 min)
2
5
0 .9 m a x
(0 .0 3 5 m a x )
9.1 max
(0.358 max)
0 .5 3 m a x
9 .3 7 /9 .6 7
(0 .0 2 m a x )
(0 .3 7 /0 .3 8 )
12.35 nom
(0.486 nom)
3
Outline in mm (inches) - HC45/U, EB
8 .8 m a x
(O .3 4 6 m a x )
6 .6 m a x
(0 .2 6 0 m a x )
1 2 .7 m in
(0 .5 0 m in )
T a g p o s itio n
o r p re s e n c e
o p tio n a l
Æ 0 .5 3 m a x 5 p la c e s
(Æ 0 .0 2 0 m a x )
5
0 .9 S Q m a x
(0 .0 3 5 S Q m a x )
1
4
2
7 .0 4 /7 .2 9
(0 .2 7 7 /0 .2 8 7 )
C ry s ta l c o n n e c
to p in s 1 a n d 3
2 a n d 4 , e a rth
5 c o n n e c te d to
te d
o r
le a d
c a s e
3 .7 5 (0 .1 4 7 )
8 .2 6 m a x
(0 .3 2 5 m a x )
3
8 .8 m a x
(0 .3 4 6 m a x )
1 2 .7 m in
(0 .5 m in )
Æ 0 .3 5
(Æ 0 .0 1 4 )
3 .7 5 (0 .1 4 7 )
3 .7 m a x
(0 .1 4 5 m a x )
1 2 3
3 .7 m a x
(0 .1 4 5 m a x )
8 .2 6 m a x
(0 .3 2 5 m a x )
P in
1 . C
2 . C
3 . C
c o n n e c tio n s
ry s ta l
a s e & G ro u n d
ry s ta l
Frequency/Temperature Curves SC Cut -60+120°C
4
0
T h e ta a n g le (m in )
T h e ta a n g le (m in )
0
0
3
2 4
0
F re q u e n c y p p m
F re q u e n c y p p m
– 2
– 4
– 6
– 8
– 1 0
– 1 2
– 1 4
1 2 .7 m in
(0 .5 m in )
Æ 0 .3 5
(Æ 0 .0 1 4 )
Frequency/Temperature Curves SC Cut -40+140°C
0
7 .0 m a x
(0 .2 7 5 m a x )
7 .0 m a x
(0 .2 7 5 m a x )
1 5 .7 5 m a x
(0 .6 2 0 m a x )
1 3 .4 m a x
(0 .5 2 8 m a x )
0
19.4 max
(0.76 max)
Note: Metal case conductive finish
Outline in mm (inches) - HC37/U (TO8) DL
0
5.66 min
(0.223 min)
1
4
1 4
1 2
1 0
8
6
4
2
18.05 max
(0.711 max)
0.76 min
(0.03 min)
QUARTZ
CRYSTALS
C =
7 .6 2 (0 .3 ) m a x
8 .8 9 (0 .3 5 ) m a x
1 1 .6 (0 .4 5 7 ) m a x
2 0
0
1 6
0
1 2
0
4
0
1 .5
1
1 .0
0
0 .5
– 1
8
0
2 .0
2
0
– 2
0
– 3 - 0 .5
0
0
– 4 0
– 2 0
0
2 0
4 0
6 0
8 0
1 0 0
1 2 0
– 4
1 4 0
T e m p e ra tu re (° C )
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
29
6 0
7 0
8 0
9 0
T e m p e ra tu re (° C )
Americas Tel: +1 919 941 0430
1 0 0
1 1 0
1 2 0
Fax: +1 919 941 0530
CFPX-3000 ESA/SCC Approved Quartz Crystals
Outline in mm (inches): ESA/SCC 3501/001,
3501/008 & 3501/011 CFPX-3750 Series - (scale 1.5:1)
ISSUE 1; 18 MAY 1998
QUARTZ
CRYSTALS
n
C-MAC has held ESA/SCC Qualification Approval
for quartz crystals since 1985. This provides customers with a source of crystal units that can be released
as fully conforming to ESA/SCC requirements. The
certification is for Qualification Approval, which enables C-MAC to supply crystal resonators within the
frequency range and holder styles listed below. The
applicable specifications are Generic Specification
ESA/SCC 3501 and Detail Specifications 3501/001,
3501/002, 3501/008, 3501/009 and 3501/011.
8 .5 m a x
(0 .3 3 5 m a x )
6 .6 m a x
(0 .2 6 0 m a x )
1 2 .7 m in
(0 .5 0 0 m in )
Æ 0 .4 /0 .4 8
(Æ 0 .0 1 6 /0 .0 1 9 )
4 .9 3 /5 .2 3
(0 .1 9 4 /0 .2 0 6 )
Key Features:
n
A range of quartz crystal units to full ESA/SCC approval
n
The product and processes are under the control of
the ESA inspectorate via Lot Acceptance Testing
n
Specifications can be issued against specific customer
requirements within the boundaries of the approval
n
Products can be supplied against this release for all
ESA projects
T a g p o s itio n
o r p re s e n c e
o p tio n a l
0 .8 7 m a x
(0 .0 3 4 m a x )
1
3
Outline in mm (inches): ESA/SCC 3501/002 &
3501/009 CFPX-3758 Series
ESA /S C C 3 5 0 1 / 0 0 1, 3 50 1/ 00 8 a nd 3 50 1/ 01 1
specification:
6 .6 m a x
(0 .2 6 0 m a x )
Frequency: 4.0 - 140.0MHz in Fundamental , 3rd
Overtone and 5th Overtone Mode
n
Holder Style: Metal welded type T807
n
CFPX Series: CFPX-3750
1 2 .7 m in
(0 .5 0 m in )
T a g p o s itio n
o r p re s e n c e
o p tio n a l
ESA/SCC 3501/002 and 3501/009 specification:
n
Frequency: 2.5 - 20.0MHz Fundamental Mode
n
Holder Style: Metal welded type T1507
n
CFPX Series: CFPX-3758
1 5 .7 5 m a x
(0 .6 2 0 m a x )
1 3 .4 m a x
(0 .5 2 8 m a x )
Range of Qualification
n
1 0 .7 m a x
(0 .4 2 1 m a x )
2
5
0 .9 S Q m a x
(0 .0 3 5 S Q m a x )
4
1
Æ 0 .5 3 m a x 5 p la c e s
(Æ 0 .0 2 0 m a x ) 5 p la c e s
2
7 .0 4 /7 .2 9
(0 .2 7 7 /0 .2 8 7 )
C ry s ta l
to p in s
e a r th le
c o n n e c
c o n n e c te d
2 a n d 4 ,
a d 5
te d to c a s e
3
Ordering Procedure
n
Please refer to ESA/SCC Table 1 and enter parameters as required
Europe Tel: +44 (0)1460 74433
Fax: +44 (0)1460 72578
30
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530
ESA/SCC Table 1
1
Customer Fax Form - Please copy form, fill out and fax to CFP on +44 (0)1460 72578
Characteristic
Symbol
Limits
Unit
Min.
Max.
Holder Style
2
Resonance Frequency
Fr or fL
MHz
3
Reference Temperature
To
°C
4
Overtone Order
5
Load Capacitance
CL
pF
6
Rated Drive Level
Po
mW
7
Frequency Adjustment Tolerance
Df
f
10–6
At To°C
8
Resonance Resistance
Rr or RL
W
At To°C
9
Df
f
DR
R
10–6
From frequency measured at To°C
%
From resistance measured at To°C
11
Frequency Variation with Temperature
over Top
Resistance Variation with Temperature
over Top
Operating Temperature Range
Top
°C
12
Frequency variation with Drive Level
10
10–6
Df
f
Resistance variation with Drive Level
14
Motional Inductance
L1
mH
15
Motional Capacitance
C1
fF
16
Static Capacitance
Co
pF
17
Q Factor
Q
-
18
19
Ratio of unwanted:
Response Resistance to
Resonance Resistance
or
Response Impedance to
Resonance Resistance
Ageing
20
Terminal Length
21
Storage Temperature Range
22
Intended Application
DR
R
mW
In the frequency range:
fkHz
to
f+
kHz
Rp/R
or
IZpI/R
Df
f
10–6
L
mm
Tstg
°C
Fax: +44 (0)1460 72578
mW
%
13
Europe Tel: +44 (0)1460 74433
From PS1 =
to
PS2 =
Remarks
QUARTZ
CRYSTALS
No
31
Americas Tel: +1 919 941 0430
Fax: +1 919 941 0530