CRYSTAL CLOCK OSCILLATORS TTL Compatible Enable/Disable Data Sheet 8706A Rev. M HS-1200/1210 Series Description The HS-1200/1210 Series of quartz crystal oscillators provide enable/disable 3-state TTL compatible signals for bus connected systems. Supplying Pin 1 of the HS-1200 units with a logic “0" enables the output on Pin 8. Alternately, supplying pin 1 of the HS-1210 units with a logic “1" enables its Pin 8 output. In the disabled mode, Pin 8 presents a high impedance to the load. All units are resistance welded in an all metal package, offering RFI shielding, and are designed to survive standard wave soldering operations without damage. Insulated standoffs to enhance board cleaning are standard. Features • Wide frequency range– 0.5MHz to 36MHz • User specified tolerance available • Will withstand vapor phase temperatures of 253°C for 4 minutes maximum • Space-saving alternative to discrete component oscillators • High shock resistance, to 3000g • All metal, resistance weld, hermetically sealed package • Low Jitter • High Q Crystal actively tuned oscillator circuit • Power supply decoupling internal • No internal PLL avoids cascading PLL problems • Low power consumption • Gold plated leads - Solder dipped leads available upon request Electrical Connection Pin Connection 1 7 8 14 Enable Input Grd & Case Output VCC Dimensions are in inches and (MM) 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: [email protected] www.nelfc.com Data Sheet 8706A CRYSTAL CLOCK OSCILLATORS Rev. M HS-1200/-1210 Series Continued TTL Compatible - Enable/Disable Operating Conditions and Output Characteristics Electrical Characteristics Parameter Frequency Duty Cycle Logic 0 Logic 1 Rise & Fall Time Tpz Enable/Disable Logic High Voltage Enable/Disable Logic Low Voltage Jitter, RMS(2) Frequency Stability (1) Symbol --------VOL VOH tr,tf ----- Conditions ----@ VCC/2 @ 16mA @ 0.4mA @ 0.4 to 2.4V ----1K internal pullup to VCC ------------dF/F -5.5mA IIL ----Overall conditions including: voltage, calibration, temp., 10 yr aging, shock, vibration Min 0.5MHz 40/60% ----2.4V --------- Typical ------------------------- Max 36.0MHz 60/40% 0.4V ----5 ns 25 ns 2.4V 2.0V ----- ---------100ppm 0.2V --------- 0.4V 8 psec +100ppm Min 4.5V 0.0 mA 0.0 mA 0°C -55°C --------------------- Typical 5.0V ------------------------------------- Max 5.5V 55 mA ±16.0 mA 70°C 125°C 303 mW 300°C 10TTL gate 2 ms 10 ms General Characteristics Parameter Supply Voltage Supply Current Output current Operating temperature Storage temperature Power Dissipation Lead temperature Load Start-up time Symbol VCC ICC IO TA TS PD TL ---tS Conditions ----No Load ----------------Soldering, 10 sec. ----<20MHz 20MHz or greater Environmental and Mechanical Characteristics Mechanical Shock Thermal Shock Vibration Soldering Condition Hermetic Seal Per MIL-STD-202, Method 213, Condition E Per MIL-STD-833, Method 1011, Condition A 0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz 300°C for 10 seconds Leak rate less than 1 x 10 -8 atm.cc/sec of helium Footnotes: 1) Standard frequency stability (±20,±25,±50ppm & others available) 2) Jitter performance is frequency dependent. Please contact factory for full characterization. Test Load: Creating a Part Number HS - X120X - FREQ Package Code HS Leaded 4 pin (14 pin) SM Leaded 4 pin (14 pin) SMD Gull Wing Input Voltage Code Specification A 3.3V 5V Tolerance/Performance 0 ±100ppm 0-70°C 1 ±50ppm 0-70°C 7 ±25ppm 0-70°C 9 Customer Specific A ±20ppm 0-70°C B ±50ppm -40 to +85°C C ±100ppm -40 to +85°C 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: [email protected] www.nelfc.com