SPN150 150 WATT , Universal Input Fully Enclosed Switching Power Supply ELECTRICAL SPECIFICATIONS All specifications are typical at nominal input, full load. INPUT SPECIFICATIONS Input Voltage.............................................. AC 85-264V Input Frequency.......................................... 47 ~ 63 Hz Input Current.............................................. 1.00 ~ 1.3A Typ Inrush Current (100/230VAC cold start) .................13A ~ 31 Typ Power Factor .............................................. .99 OUTPUT SPECIFICATIONS Output Voltage........................................... See Chart Output Adjustment.................................... ± 10% Efficiency.................................................... 78 ~ 87% Over-Voltage Protection.............................. 115 - 150% Manual Reset FEATURES Over-Current Protection.............................. Automatic Recovery (105% min) Ripple and Noise........................................ 100 mVp-p max. REMOTE SENSE Hold-Up Time............................................. 50 mS POWER FACTOR CORRECTED Line/Load Regulation.................................. See Chart UNIVERSAL INPUT (AC85-264V) Rise Time.................................................... 470 - 1600 mS Leakage Current (100/230VAC)........................ Vin= 100V OVERVOLTAGE PROTECTION OVERCURRENT PROTECTION LIGHTWEIGHT CONSTRUCTION METAL CHASSIS WITH COVER COMPACT, LOW-PROFILE PACKAGES 3 YEAR WARRANTY Vin= 230V 0.5mA max. 0.75mA max. GENERAL SPECIFICATIONS MTBF ......................................................... >120,000 Hours Isolation Voltage Primary to Secondary............... 3000VAC Primary to Case........................ 1500VAC. Secondary to Case.................... 500VAC. Isolation Resistance.................................... 100 M-Ohms min. ENVIRONMENTAL SPECIFICATIONS SAFETIES / EMI FCC-B EN 55022-B VCCI-II Operating Temperature .............................. 0˚C~+60˚C Derates Linearly 2.5%/˚C After 50˚C Cooling........................................................ Convection Temperature Coefficient.............................. 0.02% / ˚C Humidity.......................................................20-85% Rh (non-condensing) Storage Temperature.................................. -20˚C ~ +85˚C Shock Vibration.......................................... Shock: 20G (3 directions each 3 times) Vibration: 10 ~ 55Hz PHYSICAL SPECIFICATIONS Metal Enclosed Power Supply with Terminal Strip 74 Series MODEL SPN150-05S SPN150-12S SPN150-15S SPN150-24S SPN150-48S CURRENT OUTPUT VOLTAGE EFFICIENCY 85 ~ 264 VAC 100VAC 230VAC 30.0 A 13.0 A 10.0 A 6.5 A 3.3 A 78% 82% 83% 83% 83% 81% 86% 87% 87% 87% 5 VDC 12 VDC 15 VDC 24 VDC 48 VDC LINE REGULATION LOAD REGULATION (mVmax) (MV) MAX (0~100% Load) 10 mVmax 10 mVmax 10 mVmax 20 mVmax 20 mVmax 20 mVmax 20 mVmax 20 mVmax 40 mVmax 40 mVmax SPN150 LED 0.787 7.717 (20max) (196 ±1) V. ADJ. I/O TERMINAL M4 0.610 (15.5) 6.732 (171 ±0.5) 2-No. 8-32UNC (MOUNTING HOLES) BOTTOM +S 3.484 N A/C IN 0.335 L (8.5) -S (88.5 ±0.5) -V 4.213 (107±1) +V 1.772 (45 ±1) 2-No. 8-32UNC (MOUNTING HOLES) INCH (21) *MOUNTING SCREWS NOT TO EXCEED MAX. PENETRATION OF 6mm. *REMOVE SHORT BAR BETWEEN (+S) AND (+V) , (-S) AND (-V) WHEN USE REMOTE SENSING. *TOLERANCE ±1mm. *ALL DIMENSIONS IN INCH (mm) 0.827 NOTE: 6.949 (176.5 ±0.5) 0.394 (10) SPN 150 NOTE: All specifications typical and nominal / full load and 25˚C unless otherwise noted. Mounting screw lenght should not exceed 0.31 inches or 8 mm. Avoid sustained operation in overload or dead short conditions. Specifications subject to changes without notice. 75 • No. 8-32 mounting holes standard • Dimensions in mm • Terminal block or “pin” type connector available