FEATURES • –55°C to +85°C operation • 0 to 40 VDC volt input • Up to 40 dB attenuation 110 kHz to 50 MHz • Transient suppression • Compliant to MIL-STD-461C, CE03 EMI INPUT FILTERS 28 VOLT INPUT FM-461, FMA-461 AND FMB-461 EMI FILTERS 1.75 TO 5 AMP MODELS INPUT VOLTAGE AND CURRENT Input (V) 0 - 40 0 - 40 0 - 40 Current ( A) 1.75 3.8 5.0 Size (max.): Non-flanged case H3 or H5 2.125 x 1.125 x 0.495* inches (53.98 x 28.58 x 12.57* mm) Flanged case K4 or K6 2.910 x 1.125 x 0.495* inches (73.91 x 28.58 x 12.57* mm) See Section B8, cases H3, H5, K4, and K6, for dimensions. *Height varies depending on model. Weight: Maximum – FM-461 38 grams, FMA-461 42 grams, FMB-461 43 grams Screening: Standard or ES. See Section C2 for screening options, see Section A5 for ordering information. DESCRIPTION The FM-461, FMA-461, and FMB-461 EMI filter modules have been specifically designed to reduce the input line reflected ripple current of Interpoint’s MTO, MTW, MHE, MLP, and MFW Series of DC/DC converters. They are intended for use in applications of high frequency ( 100 kHz) switch-mode DC/DC converters which must meet MIL-STD-461C levels of conducted power line noise. FILTER OPERATION A fast-reacting (1 picosecond) transient suppressor clamps the input voltage at approximately 47 V, protecting the DC/DC converter from line induced transients. These filters are built using thick-film hybrid technology and are sealed in metal packages for military, aerospace, and other highreliability applications. See Section B8, cases H3, H5, K4, and K6 for dimensions. See Section C2 for screening options. The filters are rated to operate, with no degradation of performance, over the temperature range of –55°C to +85°C (as measured at the baseplate). Above 85°C, input voltage and current must be derated as specified in “Derating” on the following page. The maximum power dissipation of the filters at maximum input current represents a power loss of less than 3% at typical input voltage. MIL-STD NOISE MANAGEMENT LAYOUT REQUIREMENTS When used in conjunction with Interpoint’s DC/DC converters (see connection diagram, Figure 2), the input ripple current will be reduced by 40 dB within the frequency band of 100 kHz to 50 MHz. This gives the filter/converter combination a performance which exceeds the CE03 test limit of MIL-STD-461C. The CE03 performance of a model MHE2805S converter with and without the FM-461 filter is shown in Figures 6 and 7. The case of the filter must be connected to the case of the converter through a low impedance connection to minimize EMI. B5-3 EMI INPUT FILTERS FM-461 EMI FILTER 1.75 TO 5 AMP ABSOLUTE MAXIMUM RATINGS RECOMMENDED OPERATING CONDITIONS DERATING Input Voltage • 0 to 40 VDC continuous Lead Soldering Temperature (10 sec per lead) • 300°C Storage Temperature Range (Case) • –55°C to +135°C Isolation • 100 megohm minimum at 500 V • Any pin to case (except case pin) Input Voltage Derate linearly from 100% at 85°C case to the 33 VDC at 125°C case Input Ripple Current Derate linearly from 100% at 85°C case to the following at 125°C case 270 mA rms FM-461 400 mA rms FMA-461 480 mA rms FMB-461 DC Input and Output Current Derate linearly from 100% at 85°C case to the following at 125°C case 750 mA FM-461 1.7 A FMA-461 1.7 A FMB-461 Input Voltage Range • 0 to 40 VDC continuous Case Operating Temperature (Tc) • –55°C to +85°C full power • –55°C to +125°C absolute Electrical Characteristics: 25°C Tc, nominal Vin, unless otherwise specified. FM-461 PARAMETER INPUT VOLTAGE INPUT CLAMPING VOLTAGE INPUT CURRENT FMA-461 FMB-461 CONDITION MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS CONTINUOUS 0 28 40 0 28 40 0 28 40 VDC –55°C 38.9 43.2 47.5 38.9 43.2 47.5 38.9 43.2 47.5 +25°C 42.3 47.0 51.7 42.3 47.0 51.7 42.3 47.0 51.7 +125°C 44.9 49.9 54.8 44.9 49.9 54.8 44.9 49.9 54.8 VDC DC — — 1.75 — — 3.8 — — 5.0 A RIPPLE — — 0.67 — — 1.0 — — 1.2 A rms 15 kHz - 50 MHz — 40 — — 40 — — 40 — dB STEADY STATE — 0.38 0.42 0.07 0.10 0.15 0.07 0.09 0.10 Ω ANY PIN TO CASE 1900 — 2200 3700 — 4400 6450 — 8000 pF NOISE REJECTION DC RESISTANCE (RDC) CAPACITANCE OUTPUT VOLTAGE 1 STEADY STATE OUTPUT CURRENT POWER DISSIPATION STEADY STATE — — 1.75 — — 3.8 — — 5.0 A MAX. CURRENT — — 1.3 — — 1.6 — — 2.5 W VOUT = VIN - IIN(RDC) VDC Note 1. Typical applications result in Vout within 2% of Vin. 469 mH 2.4 mH Positive Output Positive Input 1000 pF x2 0.1 mF 0.01mF 0.001mF 50 V Input Common Output Common 4.7 mF 150 V FM-461 47 pF FIGURE 1: SCHEMATIC B5-4 1000 pF 500 V EMI INPUT FILTERS 2.4 mH >150 mH Positive Input FM-461 EMI FILTER 1.75 TO 5 AMP x2 1000 pF 0.1 mF x3 x2 0.01 mF Positive Output 0.001 mF 50 V x2 Input Common Output Common 4.7 mF 150 V 1000 pF 500 V FMA-461 47 pF FIGURE 2: SCHEMATIC P6KE47 Positive Input 0.65 V 3.5 mH 3.5 mH 18.8 mF 9.4 mF 4.7 mF 50 V Positive Output Output Common Input Common 47 pF 500V 3300 pF 500 V FMB-461 FIGURE 3: SCHEMATIC EMI FILTER +Vin +Vout Case Output Input Common Common Chassis ground DC/DC CONVERTER +Vin +Vout Case Output Input Common Common Multiple units allowed up to rated output current of filter RL RL The case ground connection should be as low an impedance as possible to minimize EMI. Direct contact of baseplate to chassis ground provides the lowest impedance. FIGURE 4: CONNECTION DIAGRAM B5-5 FM-461 EMI FILTER 1.75 YO 5 AMP EMI INPUT FILTERS PIN OUT Squared corner and dot on top of package indicate pin one. 1 Pin 1 2 3 4 5 Designation Positive Input Positive Output Case Ground Output Common Input Common 2 BOTTOM VIEW FM-461, FMA-461, FMB-461 5 3 4 Dotted line outlines flanged package option. See Section B8, cases H3, H5, K4, and K6, for dimensions. FIGURE 5: PIN OUT MODEL NUMBERING KEY FMB - 461 F / ES Base Model FM, FMA, or FMB MIL-STD-461 reference Case Option (Non-flanged case has no designator in this position) Screening (Standard screening has no designator in this position) Typical Performance Curves: 25°C Tc , nominal Vin, unless otherwise specified. 90 90 CE03 Limit CE03 Limit 70 EMISSION LEVEL (dmA) EMISSION LEVEL (dmA) 70 50 30 10 .015 50 30 10 .1 1 10 50 .015 .1 FREQUENCY (MHz) B5-6 1 10 FREQUENCY (MHz) MHE Converter Without Filter MHE Converter With FM-461 EMI Filter FIGURE 6 FIGURE 7 26221-001-DTS Rev A DQ# 14006 All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1990 - 1999 Interpoint. All rights reserved. 50 CASES Dot on top of case indicates pin one CASE H BOTTOM VIEW See Figures 29 – 34 for pin configurations. 1.125 max (28.58) 2.125 max (53.98) CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. CASE H Materials Header Cold Rolled Steel/Nickel/Gold cases H1 and H2 Cold Rolled Steel/Nickel/Tin cases H3, H4, and H5 Cover Kovar/Nickel cases H1 and H2 Cold Rolled Steel/Nickel/Tin cases H3, H4, and H5 Pins #52 alloy ceramic seal case H1 case H2 (except MHV Series Single and Dual) compression glass seal MHV Series Single and Dual case H3, H4, H5 Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified FIGURE 28: CASE H MAXIMUM DIMENSIONS BOTTOM VIEW CASE H1 FMC EMI Filter: Screening – Standard, ES, or 883 SFMC EMI Filter: Screening – Space Standard, H, or K Seam Seal Squared corner and dot on top of case indicate pin one. 0.040 dia (1.02) 1.110 (28.19) 0.955 (24.26) 1 2 3 0.555 (14.1) 5 4 0.155 (3.94) 2.090 (53.01) 1.845 (46.86) 0.245 (6.22) 0.000 0.25 ±0.03 (6.4 ±0.8) 0.000 0.400 max. (10.16) 0.000 FIGURE 29: CASE H1 Note: Although every effort has been made to render the case drawings at actual size, variations in the printing process may cause some distortion. Please refer to the numerical dimensions for accuracy. B8-17 CASES CASE H BOTTOM VIEW CASE H3 FM-461 EMI Filter: Screening – Standard of ES Squared corner and dot on top of case indicate pin one. Solder Seal 1.120 (28.45) 0.960 (24.38) 1 0.040 dia (1.02) 2 3 0.560 (14.22) Solder Tip-off 5 4 0.160 (4.06) 2.110 (53.59) 1.855 (47.12) 0.255 (6.48) 0.000 0.25 +0.05/-0.00 (6.4 +1.3/-0.0) 0.000 0.417 max (10.59) 0.000 FIGURE 31: CASE H3 B8-19 CASES CASE H BOTTOM VIEW CASE H5 FMA-461and FMB-461 EMI Filter: Screening – Standard of ES Squared corner and dot on top of case indicate pin one. Solder Seal 1.120 (28.45) 0.960 (24.38) 1 0.040 dia (1.02) 2 3 0.560 (14.22) Solder Tip-off 5 4 0.160 (4.06) 2.110 (53.59) 1.855 (47.12) 0.255 (6.48) 0.000 0.25 +0.05/-0.00 (6.4 +1.3/-0.0) 0.495 max (12.57) 0.000 0.000 FIGURE 33: CASE H5 BOTTOM VIEW CASE H6 MHE Series: Screening – Standard or ES HR151 Series and HR152 Series: no screening options Dot on top of case indicates pin one Solder Seal 1.120 (28.45) 1 2 3 4 5 10 9 8 7 6 0.655 (16.64) 1.055 (26.80) 0.040 dia (1.02) 0.255 (6.48) 0.960 (24.38) Solder Tip-off 0.160 (4.06) 2.110 (53.59) 1.855 (47.12) 1.455 (36.96) 0.000 0.25 +0.05/-0.00 (6.4 +1.3/-0.0) 0.000 0.495 max (12.57) 0.000 FIGURE 34: CASE H6 B8-21 CASE K CASES Dot on top of case indicates pin one CASE K BOTTOM VIEW See Figures 42 - 48 for pin configuration 1.125 max (28.58) 2.910 max (73.91) Flange Thickness: Cases K1, K2, K3 and MLP Series (K5) 0.060 (1.52) Cases K4, K5 (except MLP Series), K6, K7, and K8 0.067 +0.005/-0.007 (1.70 +0.13/-0.8) Materials Header Case K1 - K3 Cold Rolled Steel/Nickel/Gold Cases K4 - K8 Cold Rolled Steel/Nickel/Tin Cover Case K1 - K3 Kovar/Nickel Case K4 - K8 Cold Rolled Steel/Nickel/Tin Pins #52 alloy (all cases) Case K1, K2, and K3 (except MHV Series Single and Dual) ceramic seal Cases K4 - K8 and MHV Series Single and Dual (K3) compression glass seal Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.2) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. FIGURE 41: CASE K MAXIMUM DIMENSIONS B8-26 CASE K CASES BOTTOM VIEW CASE K4 Flanged case: Designator required in Case Option position of model number. FM-461 EMI Filter: Screening – Standard or ES Squared corner and dot on top of case indicate pin one. Solder Seal 1.115 (28.32) 0.955 (24.26) 1 0.040 dia (1.02) 2 0.162 dia (4.11) 3 0.555 (14.1) Solder Tip-off 5 4 2.320 (58.93) 1.845 (46.86) 0.245 (6.22) 0.000 0.230 (5.84) 0.25 ±0.03 (6.4 ±0.8) 0.417 max (10.59) 0.000 0.155 (3.94) 0.000 FIGURE 45: CASE K4 BOTTOM VIEW CASE K5 Flanged cases: Designator required in Case Option position of model number. MTR Series Dual and MLP Series: Screening – Standard or ES Squared corner and dot on top of case indicate pin one. Solder Seal 1.115 (28.32) 0.955 (24.26) 1 0.040 dia (1.02) All K5 cases 2 3 4 5 6 MTR Series Dual (Standard and ES) 0.555 (14.1) 10 9 8 7 0.245 (6.22) 0.645 (16.38) 1.045 (26.54) 1.445 (36.70) Solder Tip-off 0.155 (3.94) 2.320 (58.93) 1.845 (46.86) 0.000 – 0.230 (5.84) 0.25 ±0.03 (6.4 ±0.8) Squared corner and dot on top of case indicate pin one. 1.115 (28.32) 2 4 5 8 7 6 1.445 (36.70) 1 1.045 (26.54) 0.955 (24.26) 3 MLP Series 0.555 (14.1) 10 9 0.155 (3.94) 2.320 (58.93) 1.845 (46.86) 0.645 (16.38) 0.245 (6.22) 0.000 0.000 0.230 (5.84) 0.000 0.417 max (10.59) 0.000 FIGURE 46: CASE K5 B8-29 CASES CASE K BOTTOM VIEW CASE K6 Flanged cases: Designator required in Case Option position of model number. FMA-461 and FMB-461 EMI Filters: Screening – Standard or ES Squared corner and dot on top of case indicate pin one. Solder Seal 1.115 (28.32) 0.955 (24.26) 1 0.040 dia (1.02) 2 0.162 dia (4.11) 3 0.555 (14.1) Solder Tip-off 5 4 0.155 (3.94) 2.320 (58.93) 2.090 (53.01) 1.845 (46.86) 0.245 (6.22) 0.000 0.230 (5.84) 0.25 ±0.03 (6.4 ±0.8) 0.495 max (12.57) 0.000 0.000 FIGURE 47: CASE K6 BOTTOM VIEW CASE K7 Flanged case: Designator required in Case Option position of model number. MHE Series: Screening – Standard or ES Squared corner and dot on top of case indicate pin one. Solder Seal 1.115 (28.32) 1 2 3 4 5 10 9 8 7 6 0.245 (6.22) 0.645 (16.38) 1.045 (26.54) 1.445 (36.70) 0.955 (24.26) 0.040 dia (1.02) 0.555 (14.1) Solder Tip-off 0.155 (3.94) FIGURE 48: CASE K7 B8-30 2.320 (58.93) 1.845 (46.86) 0.000 – 0.230 (5.84) 0.25 ±0.03 (6.4 ±0.8) 0.000 0.495 max (12.57) 0.000 QA SCREENING 85°C PRODUCTS 85°C PRODUCTS TEST (85°C Products excluding HR products) STANDARD /ES yes yes no yes no yes no yes yes yes Fine Leak, Method 1014, Cond. A no yes Gross Leak, Method 1014, Cond. C no yes Gross Leak, Dip (1 x 10-3) yes no yes yes PRE-CAP INSPECTION Method 2017 TEMPERATURE CYCLE (10 times) Method 1010, Cond. B, -55°C to 125°C CONSTANT ACCELERATION Method 2001, 500 g BURN-IN 96 hours at 70°C ambient (typical) FINAL ELECTRICAL TEST MIL-PRF-38534, Group A Subgroups 1 and 4: +25°C case HERMETICITY TESTING FINAL VISUAL INSPECTION Method 2009 Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. Applies to the following products: MFW Series MTW Series MHE/MLP Series MHL Series MRH Series MTO Series MSR Series DCH Series FM/FMA/FMB EMI Filters MSF EMI Filter C2-12