C&K TS Series Tiny Slide Switches Features/Benefits • Reliable contact design ensures long electrical life • Ratings up to 3 AMPS • Epoxy terminal-seal compatible with bottom wash cleaning • RoHS compliant Typical Applications • Test & measurement equipment • Computers & peripherals • Telecommunications & networking equipment Models Available Materials CONTACT RATING: B contact material: 0.4 VA max. @ 20 V AC or DC max. Q contact material (TS01 Model): 3 AMPS @ 120 V AC or 28 V DC; (TS02, TS03 Models): 1 AMP @ 120 V AC or 28 V DC. See page I-10 for additional ratings. ELECTRICAL LIFE: TS01 MODELS: 60,000 make-and-break cycles at full load. TS02, TS03 MODELS: 30,000 cycles. CONTACT RESISTANCE: Below 20 m Ω typ. initial @ 2-4 V DC, 100 mA, for both silver and gold plated contacts. INSULATION RESISTANCE: 109 Ω min. DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level. OPERATING TEMPERATURE: –30ºC to 85ºC SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). CASE: Glass filled nylon 6/6, flame retardant, heat stabilized, or diallyl phthalate (DAP) (UL 94V-0). ACTUATOR: Nylon, black standard. HOUSING: Stainless steel or stainless steel, nickel plated. END CONTACTS: B contact material: Copper alloy, with gold plate over nickel plate. Q contact material: Coin silver, silver plated. See page I-10 for additional contact materials. CENTER CONTACT & ALL TERMINALS: B contact material: Copper alloy, with gold plate over nickel plate. Q contact material: Copper alloy, silver plated. See page J-9 for additional contact materials. TERMINAL SEAL: Epoxy. Refer to Soldering and Cleaning in Technical Data chapter. NOTE: Any models supplied with Q, B, G, P, S or R contact material are RoHS compliant. For the latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs. NOTE: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages J–8 and J–9. For additional options not shown in catalog, consult Customer Service Center. All models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods. Switch Function TS01 SPDT On-None-On TS02 SPST Off-None-On TS03 SPDT On-Off-On Terminations A Right angle, PC thru-hole (TS01 & TS03 models only) C PC Thru-hole W Wire wrap Contact Material B Gold Q Silver K Gold, tin-lead M Silver, tin-lead G Gold over silver L Gold over silver, tin-lead P Gold, matte-tin S Silver, matte-tin R Gold over silver, matte-tin Seal E Epoxy F Epoxy seal and splashproof RTV latex rubber seal Dimensions are shown: Inch (mm) Specifications and dimensions subject to change J–7 www.ittcannon.com J Slide Specifications C&K TS Series Tiny Slide Switches SWITCH FUNCTION SWITCH FUNCTION POS. 1 POS. 2 POS. 3 NO. POLES MODEL NO. POS. 1 C&K marking on opposite side TS01 ON NONE ON TS03 ON OFF ON TS02 OFF NONE ON CONNECTED TERMINALS POS. 2 C&K marking on opposite side 1-2 SP J POS. 3 OPEN SCHEMATIC 2-3 SPDT OPEN N/A 3-1 SPST Slide SPDT TS02 models: Omit center terminal Terminal Nos. For Reference Only Part number shown: TS01CBE All models with all options when ordered with G, L, M, Q, R or S contact material. TS02 model not available with A terminations. TERMINATIONS C W PC THRU-HOLE WIRE WRAP PC MOUNTING TS02 models: Omit center hole SPDT and SPST A SPDT and SPST RIGHT ANGLE, PC THRU-HOLE PC MOUNTING TS01ABE Horizontal Actuation SPDT Actuator shown in pos. 1 Not available with TS02 model. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change J–8 www.ittcannon.com C&K TS Series Tiny Slide Switches CONTACT MATERIAL OPTION CODE RoHS COMPLIANT RoHS COMPLIANT B YES YES K NO YES P YES YES Q YES YES M NO YES S YES YES G YES YES CONTACT MATERIAL GOLD 3 GOLD 1 NO YES R YES YES TIN-LEAD 6 LOW LEVEL/DRY CIRCUIT MATTE-TIN 7 0.4 VA MAX. @ 20 V AC OR DC MAX. GOLD 3 SILVER 4,5 TIN-LEAD 6 MATTE-TIN POWER SILVER 2,3 TS01 MODELS: 3 AMPS @ 120 V AC OR 28 V DC. TS02, TS03 MODELS: 1 AMP @ 120 V AC OR 28 V DC. 7 GOLD 3 GOLD OVER L RATINGS TERMINAL PLATING TIN-LEAD 6 LOW LEVEL/DRY CIRCUIT OR POWER MATTE-TIN 7 TS01 MODELS: 0.4 VA MAX @20 V AC OR DC MAX. OR 3 AMPS @ 120 V AC OR 28 V DC. TS02, TS03 MODELS: 0.4 VA MAX @ 20 V AC OR DC MAX. OR 1 AMP @ 120 V AC OR 28 V DC. Slide * Note: See Technical Data section of this catalog for RoHS compliant and compatible definitions and specifications. 1 CONTACTS & TERMINALS: Copper alloy, with gold plate over nickel plate. All models 2 END CONTACTS: Coin silver, with gold plate over nickel plate. B contact material standard with A and W terminations. 3 CENTER CONTACTS & ALL TERMINALS: Copper alloy, with gold plate over nickel plate. Q contact material standard with C terminations. 4 END CONTACTS: Coin silver, silver plated. 5 CENTER CONTACT & ALL TERMINALS: Copper alloy, silver plated. 6 TERMINALS: Copper alloy, with tin-lead alloy over nickel plate. 7 TERMINALS: Copper alloy, with matte-tin over nickel plate with all options when ordered with G, L, M,S or R contact material. NOTE: Any models supplied with Q, B, G, P, S or R contact material are RoHS compliant. For the latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs. SEAL E F EPOXY SEAL EPOXY SEAL AND SPLASHPROOF RTV LATEX RUBBER SEAL NOTE: RTV latex rubber seal peels off easily after installation. Epoxy terminal seal standard. Not available with A termination. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change J–9 J www.ittcannon.com