1.6X0.8mm SMD CHIP LED LAMP Part Number: APT1608SURCK Features Description z1.6mmX0.8mm zLOW SMT LED, 0.75mm THICKNESS. POWER CONSUMPTION. VIEWING ANGLE. zIDEAL FOR BACKLIGHT AND INDICATOR. COLORS AND LENS TYPES AVAILABLE. zPACKAGE: 2000PCS / REEL . zMOISTURE SENSITIVITY LEVEL : LEVEL 3. zRoHS The Hyper Red source color devices are made with DH InGaAlP on GaAs substrate Light Emitting Diode. zWIDE zVARIOUS HYPER RED COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3.Specifications are subject to change without notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAD0926 REV NO: V.8 DATE: APR/20/2007 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1203005341 Selection Guide Dice Part No. APT1608SURCK Iv (mcd) [2] @ 20mA Lens Type HYPER RED (InGaAlP) Viewing Angle [1] Min. Typ. 2θ1/2 50 150 120° WATER CLEAR Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device λpeak Peak Wavelength Hyper Red λD [1] Dominant Wavelength Δλ1/2 Typ. Max. Units Test Conditions 650 nm IF=20mA Hyper Red 635 nm IF=20mA Spectral Line Half-width Hyper Red 28 nm IF=20mA C Capacitance Hyper Red 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR = 5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD0926 REV NO: V.8 DATE: APR/20/2007 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1203005341 Hyper Red APT1608SURCK SPEC NO: DSAD0926 REV NO: V.8 DATE: APR/20/2007 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1203005341 APT1608SURCK Recommended Soldering Pattern (Units : mm; Tolerance: ±0.1) Tape Specifications (Units : mm) SPEC NO: DSAD0926 REV NO: V.8 DATE: APR/20/2007 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1203005341 PACKING & LABEL SPECIFICATIONS APT1608SURCK SPEC NO: DSAD0926 REV NO: V.8 DATE: APR/20/2007 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1203005341