TECHNICAL DATA Low Power Quad Operational Amplifier The KK2902 contains four independent high gain operational amplifiers with internal frequency compensation. The four op-amps operate over a wide voltage range from a single power supply. Also use a split power supply. The device has low power supply current drain, regardless of the power supply voltage. The low power drain also makes the KK2902 a good choice for battery operation. When your project calls for a traditional op-amp function, now you can streamline your design with a simple single power supply. Use ordinary +5VDC common to practically any digital system or personal computer application, without requiring an extra 15V power supply just to have the interface electronics you need. The KK2902 is a versatile, rugged workhorse with a thousand-and-one uses, from amplifying signals from a variety of transducers to dc gain blocks, or any op-amp function. The attached pages offer some recipes that will have your project cooking in no time. • • • • • • • • Internally frequency compensated for unity gain Large DC voltage gain: 100dB Wide power supply range: 3V ~ 32V (or ±1.5V ~ ±16V) Input common-mode voltage range includes ground Large output voltage swing: 0V DC to VCC-1.5V DC Power drain suitable for battery operation Low input offset voltage and offset current Differential input voltage range equal to the power supply voltage LOGIC DIAGRAM KK2902 ORDERING INFORMATION KK2902N Plastic KK2902D SOIC TA = -40° to +85° C for all packages. PIN ASSIGNMENT PIN 4 = VCC PIN 11= GND 1 KK2902 MAXIMUM RATINGS* Symbol VCC Parameter Value Unit 32 ±16 V Power Supply Voltages Single Supply Split Supplies VIDR Input Differential Voltage Range (1) ±32 V VICR Input Common Mode Voltage Range -0.3 to 32 V ISC TJ Output Short Circuit Duration Junction Temperature Plastic Packages Tstg Continuous °C 150 °C Storage Temperature Plastic Packages -55 to +125 IIN Input Current, per pin (2) 50 mA TL Lead Temperature, 1mm from Case for 10 Seconds 260 °C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C Notes: 1. Split Power Supplies. 2. VIN<-0.3V. This input current will only exist when voltage at any of the input leads is driven negative. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC DC Supply Voltage TA Operating Temperature, All Package Types Min Max Unit ±2.5 or 5.0 ±15 or 30 V -40 +85 °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 2 KK2902 DC ELECTRICAL CHARACTERISTICS (TA=-40 to +85°C) Guaranteed Limit Symbol VIO Parameter Test Conditions Maximum Input Offset Voltage VO=1.4V VCC=5.0-30V;RS=0Ω VICM=0V to VCC-1.7V Input Offset Voltage Drift RS=0Ω, VCC=30V Maximum Input Offset Current VCC=5.0V ∆IIO/∆T Input Offset Current Drift RS=0Ω, VCC=30V IIB Maximum Input Bias Current VCC=5.0V Input Common Mode Voltage Range VCC=30V Maximum Power Supply Current ∆VIO/∆T IIO VICR ICC Min Typ Max Unit 9.0 mV 5.0* µV/°C 7.0 150 nA 50* 10 pA/°C 500 nA 250* 0 28 V RL=∞,VCC=30V,V0=0V 3 mA RL=∞,VCC=5V,V0=0V 1.2 Minimum Large Signal VCC=15V, RL≥2KΩ Open-Loop Voltage Gain 25* VOH Minimum Output HighLevel Voltage Swing VCC=30V,RL=2KΩ VCC=30V,RL=10KΩ 26 27 VOL Maximum Output LowLevel Voltage Swing VCC=5V,RL=10KΩ CMR Common Mode Rejection VCC=30V, RS=10KΩ 65* dB PSR Power Supply Rejection VCC=30V 65* dB CS Channel Separation f=1KHz to 20KHz,VCC=30V -120* dB ISC Maximum Output Short Circuit to GND VCC=5.0V Isource Minimum Output Source Current VIN+=1V, VIN-=0V, VCC=15V, V0=0V 10 mA Minimum Output Sink Current VIN+=0V, VIN-=1V, VCC=15V, V0=15V VIN+=0V, VIN-=1V, VCC=15V, V0=0.2V 5 10* mA 12* µA AVOL Isink VIDR Differential Input Voltage Range All VIN≥GND or V-Supply (if used) 15 V/mV V 20 60* VCC* mV mA V *=@25°C 3 KK2902 TYPICAL PERFORMANCE CHARACTERISTICS Figure 1.Input Voltage Range Figure 2. Open-Loop Frequency Figure 3. Large-Signal Frequency Response Figure 4. Small-Signal Voltage Follower Pulse Response (Noninverting) Figure 5. Power Supply Current versus Power Supply Voltage Figure 6. Input Bias Current versus Power Supply Voltage 4 KK2902 N SUFFIX PLASTIC DIP (MS - 001AA) A Dimension, mm 8 14 B 7 1 Symbol MIN MAX A 18.67 19.69 B 6.1 7.11 5.33 C F L C -T- SEATING PLANE N G M K J H D 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AB) Dimension, mm A 14 8 H B 1 G P 7 R x 45 C -TK D SEATING PLANE J 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. F M Symbol MIN MAX A 8.55 8.75 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G 1.27 H 5.27 J 0° 8° K 0.1 0.25 M 0.19 0.25 P 5.8 6.2 R 0.25 0.5 5