TECHNICAL DATA KK4006B СMOS 18-Stage Static Shift Register The RCA-4006B types are composed of 4 separate shift register sections: two sections of four stages and two sections of five stages with an output tar at the fourth stage. Each section has an independent single-rail data path. • • • • N SUFFIX PLASTIC 14 Standardized, symmetriсal output characteristics Operating Voltage Range: 3.0 to 18 V 100% tested for guiescent current at 20 V Maximum input current of 1 µA at 18 V over full package-temperature range; 100 nA at 18 V and 25°C • Noise margin ( full package temperature range): 1.0 V at VDD=5.0 V 2.0 V at VDD =10.0 V 2.5 V at VDD =15.0 V PIN ASSIGNMENT D1 01 14 D1+4' 02 VDD 01 02 13 D1 D1+4/ C D2 D3 D4 VSS D4+4 D4+5 D3+4 D2+4 D2+5 D1+4 Description Input Data Output Data Clock Data Input Data Input Data Input Data Ground Output Data Output Data Output Data Output Data Output Data Output Data 14 VDD Positive Pover Supply D2+5 11 D2+4 10 D3+4 05 D4 06 09 D4+5 06 V SS 07 08 D4+4 4006 D3 05 03 04 07 08 09 FUNCTION TABLE Inputs C D1 10 11 Outputs D2-D4 D1+4...D4+4 ORDERING INFORMATION KK4006BN Plastic KK4006BD SOIC TA = -55° to 125° C for all packages Symbol 12 D2 04 1 Pin.No D1+4 03 14 D SUFFIX SOIC TERMINAL ASSIGNMENT 13 C 1 D1+4 / L L L Storage H H H Storage X X Storage D1 L X Storage L H X Storage H X X D1...D4 Storage 12 X = don’t care 1 KK4006B MAXIMUM RATINGS* Symbol Parameter VDD DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) IIN DC Input Current, per Pin PD Power Dissipation in Still Air, Plastic DIP, SOIC Package Ptot Power Dissipation per Output Transistor Tstg Storage Temperature TL Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) Value Unit -0.5 to +20 V -0.5 to VDD +0.5 V ±10 mA 500** mW 100 mW -65 to +150 °C 260 °C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. **Derating: - Plastic DIP from -55 to +100°C - SOIC Package from -55 to +65°C - Plastic DIP: - 12 mW/°C from +100 to +125°C - SOIC Package: : - 7 mW/°C from +65 to +125°C RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) TA Operating Temperature, All Package Types Min Max Unit 3.0 18 V 0 VCC V -55 +125 °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation VIN should be constrained to the range GND≤VIN ≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either Vss or VDD). Unused outputs must be left open. 2 KK4006B DC ELECTRICAL CHARACTERISTICS Symbol Parameter Test Conditions Guaranteed Limit VDD, V VIH VIL 55°C Unit 125°C 25°C min max min max min max Minimum HighVO = 0.5 V or VDD-0.5 V Level Input Voltage 5.0 3.5 - 3.5 - 3.5 - V VO = 1.0 V or VDD-1.0 V 10 7.0 - 7.0 - 7.0 - VO = 1.5 V or VDD-1.5 V 15 11 - 11 - 11 - Maximum Low VO = 0.5 V or VDD-0.5 V Level Input Voltage 5.0 - 1.5 - 1.5 - 1.5 VO = 1.0 V or VDD-1.0 V 10 - 3.0 - 3.0 - 3.0 VO = 1.5 V or VDD-1.5 V 15 - 4.0 - 4.0 - 4.0 - 4.95 9.95 14.95 - 4.95 9.95 14.95 - V V VOH Minimum HighLevel Output Voltage VI = VSS или VDD 5.0 4.95 10 9.95 15 14.95 VOL Maximum LowLevel Output Voltage VI = VSS или VDD 5.0 10 15 - 0.05 0.05 0.05 - 0.05 0.05 0.05 - 0.05 0.05 0.05 V IIL Maximum Input Current VI = VSS 18 - -0.1 - -1.0 - -0.1 µA IIH Maximum Input Leakage Current VI = VDD 18 - +0.1 - +1.0 - +0.1 µA IDD Maximum Quiescent Supply Current (per Package) VI = VSS or VDD 5.0 10 15 20 - 5.0 10.0 20.0 100 - 150 300 600 3000 - 5.0 10 20 100 µA IOL Minimum Output VI = VSS or VDD Low (Sink) Current VOL = 0.4 V VOL = 0.5 V VOL = 1.5 V 5.0 10 15 0.64 1.6 4.2 - 0.36 0.9 2.4 - 0.51 1.3 3.4 - IOH Minimum Output High (Source) Current 5.0 -2.0 5.0 -0.64 10 -1.6 15 -4.2 - -1.15 -0.36 -0.9 -2.4 - -1.6 -0.51 -1.3 -3.4 - CIN Maximum Input Capacitance - - - - 7.5 VI = VSS or VDD VOH = 2.5 V VOH = 4.6 V VOH = 9.5 V VOH = 13.5 V mA mA - - pF 3 KK4006B TIMING REQUIREMENTS (CL=50 пФ, RL = 200 кОм, tLH = tHL ≤ 20 нс) Symbol Parameter UDD, Guaranteed Limit Unit V 55°C min max - 400 125°C min max - 800 25°C min max tPHL, Propagation Delay 5.0 - 400 tPLH Time 10 200 400 200 15 160 320 160 ns tTHL, tTLH Transition Time 5.0 10 15 - 200 100 80 - 400 200 160 - 200 100 80 ns tSU Minimum Data Setup Time 5.0 10 15 100 50 40 - 200 100 80 - 100 50 40 - ns tH Minimum Hold Time, Clock to Data 5.0 10 15 150 80 60 - 300 160 120 - 150 80 60 - ns tW Minimum Clock Pulse Width 5.0 10 15 200 90 60 - 400 180 120 - 200 90 60 - nc fC Maximum Clock Input Freguency 5.0 10 15 2.5 5.0 7.0 1.25 2.5 3.5 2.5 5.0 7.0 MHz tr(CL) tf(CL) Maximum Clock Input Rise or Fall Time 5.0 10 15 15 15 15 15 15 15 15 15 15 µs 4 KK006B LOGIS DIAGRAM WITH DETAIL OF LATCH D1 (01) D Q Q D D C C C C Q C D C Q C C D 1+4 Q C C- CLOCK (03) D2 (04) D3 (05) D4 (06) D1+4 (13) D1+4 (02) D2+4 (11) D Q C D C D Q D D Q C C Q D D C Q D D C C D Q C C C D Q C C D2+5 (12) D3+4 (10) Q C Q D Q C C C C Q C C Q C C C C C D Q C C D Q C C- D4+4 (08) D4+5 (09) 5 KK4006B tHL tLH D1,D2, D3,D4 UDD 0.9 0.5 0.1 0В tH tSU tLH tHL UDD 0.9 0.5 CLK 0.1 1 4 tWH tPLH D1+4,D2+4, D3+4,D4+4 0.5 0.5 5 0.5 8 9 0.9 UOH 0.9 0.5 0.5 0.1 tTLH tPLH UOL tTHL tPHL 0.9 UOH 0.9 0.5 0.5 0.1 0.1 tTLH tPLH D2+5,D4+5 0В tPHL 0.1 D1+4/ 0.5 UOL tTHL tPHL 0.9 0.5 UOH 0.9 0.5 0.1 tTLH 0.1 UOL tTHL SWITCHING WAVEFORMS 6 KK4006B N SUFFIX PLASTIC DIP (MS - 001AA) A 8 14 B Dimensions, mm 7 1 F L -T- SEATING PLANE M K G H D MIN MAX A 18.67 19.69 B 6.10 7.11 C C N Symbol J 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. 5.33 D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.20 0.36 N 0.38 D SUFFIX SOIC (MS - 012AB) A 14 8 Dimensions, mm H B 1 G P 7 R x 45 C -TK D SEATING PLANE J F 0.25 (0.010) M T C M NOTES: 1.Dimensions A and B do not include mold flash or protrusion. 2.Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B - 0.25 mm (0.010) per side. M Symbol. MIN MAX A 8.55 8.75 B 3.80 4.00 C 1.35 1.75 D 0.33 0.51 F 0.40 1.27 G 1.27 H 5.72 J 0° 8° K 0.10 0.25 M 0.19 0.25 P 5.80 6.20 R 0.25 0.50 7