TECHNICAL DATA Speaker Amplifier KK5009 The KK5009 is a monolithic integrated circuit designed for speaker amp. FEATURES • Operating supply voltage range : Vcc = 1.5V ~ 5.0V • Recommended operating supply voltage : Vcc = 3V • Low quiescent : Icc = 3.9mA • Package is compact. ORDERING INFORMATION KK5009N Plastic KK5009D SOIC TA = -20° to 60° C for package APPLICATION • Telephone set MAXIMUM RATINGS Characteristics Supply Voltage Power Dissipation Operating Temperature Storage Temperature Symbol Rating Unit Vcc PD Topr Tstr 10 800 -20 ~ +60 -55 ~ +150 V mW ºC ºC BLOCK DIAGRAM & APPLICATION CIRCUIT KK5009 ELECTRICAL DC CHARACTERISTICS (Pin Voltage at Vcc = 3V and no input signal) Pin No. Symbol Typical Value Unit Pin No Symbol Typical Value Unit 1 V1 1.4 V 5 V5 0 V 2 V2 1.4 V 6 V6 1.5 V 3 V3 1.4 V 7 V7 2.3 V 4 V4 1.3 V 8 V8 3.0 V ELECTRICAL AC CHARACTERISTICS ( Unless otherwise specified, Vcc = 3V, f = 1KHz, VIN = 20mVrms, RL = 32Ω, Ta = 25 ºC ) Characteristic Quiescent Current Symbol Test condition Min. Typ. Max. Unit ICCO1 Vcc = 1.5V 3.1 mA ICCO2 Vcc = 3.0V 3.9 mA ICCO3 Vcc = 5.0V 4.9 mA 27 dB Close Loop Voltage Gain GV Maximum Output Voltage VOM THD = 10% 1.0 Vrms Total Harmonic Distortion THD VIN = 40m Vrms 0.6 % Output noise Voltage VNO VIN = 0 200 µVrms Input Resistance RIN 15 KΩ TYPICAL PERFORMANCE CHARACTERISTICS KK5009 N SUFFIX PLASTIC DIP (MS – 001BA) A Dimension, mm 5 8 B 1 4 MIN MAX A 8.51 10.16 B 6.1 7.11 5.33 C L F Symbol C D 0.36 0.56 F 1.14 1.78 -T- SEATING PLANE N G M K 0.25 (0.010) M J H D T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AA) Dimension, mm A 8 5 B H 1 G P 4 D K MIN MAX A 4.8 5 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 R x 45 C -T- Symbol SEATING PLANE J F 0.25 (0.010) M T C M M G 1.27 H 5.72 J 0° 8° K 0.1 0.25 1. Dimensions A and B do not include mold flash or protrusion. M 0.19 0.25 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. P 5.8 6.2 R 0.25 0.5 NOTES: