KODENSHI KK74ACT153

TECHNICAL DATA
KK74ACT153
Dual 4-Input Data Selector/Multiplexer
High-Speed Silicon-Gate CMOS
The KK74ACT153 is identical in pinout to the LS/ALS153,
HC/HCT153. The KK74ACT153 may be used as a level converter for
interfacing TTL or NMOS outputs to High Speed CMOS inputs.
The Address Inputs select one of four Data Inputs from each
multiplexer. Each multiplexer has an active-low Strobe control and a
noninverting output.
• TTL/NMOS Compatible Input Levels
• Outputs Directly Interface to CMOS, NMOS, and TTL
• Operating Voltage Range: 4.5 to 5.5 V
• Low Input Current: 1.0 µA; 0.1 µA @ 25°C
• Outputs Source/Sink 24 mA
ORDERING INFORMATION
KK74ACT153N Plastic
KK74ACT153D SOIC
TA = -40° to 85° C for all packages
PIN ASSIGNMENT
LOGIC DIAGRAM
FUNCTION TABLE
Inputs
PIN 16 =VCC
PIN 8 = GND
Output
A1
A0
Strobe
Y
X
X
H
L
L
L
L
D0
L
H
L
D1
H
L
L
D2
H
H
L
D3
D0,D1...D3=the level of the respective
Data Input
X = don’t care
1
KK74ACT153
MAXIMUM RATINGS*
Symbol
Parameter
Value
Unit
-0.5 to +7.0
V
VCC
DC Supply Voltage (Referenced to GND)
VIN
DC Input Voltage (Referenced to GND)
-0.5 to VCC +0.5
V
DC Output Voltage (Referenced to GND)
-0.5 to VCC +0.5
V
DC Input Current, per Pin
±20
mA
IOUT
DC Output Sink/Source Current, per Pin
±50
mA
ICC
DC Supply Current, VCC and GND Pins
±50
mA
PD
Power Dissipation in Still Air, Plastic DIP+
SOIC Package+
750
500
mW
-65 to +150
°C
260
°C
VOUT
IIN
Tstg
TL
Storage Temperature
Lead Temperature, 1 mm from Case for 10 Seconds
(Plastic DIP or SOIC Package)
*
Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
+Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C
SOIC Package: : - 7 mW/°C from 65° to 125°C
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
VIN, VOUT
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to GND)
TJ
Junction Temperature (PDIP)
TA
Operating Temperature, All Package Types
IOH
Output Current - High
IOL
Output Current - Low
tr, tf
*
Parameter
Input Rise and Fall Time
(except Schmitt Inputs)
*
Min
Max
Unit
4.5
5.5
V
0
VCC
V
140
°C
+85
°C
-24
mA
24
mA
10
8.0
ns/V
-40
VCC =4.5 V
VCC =5.5 V
0
0
VIN from 0.8 V to 2.0 V
This device contains protection circuitry to guard against damage due to high static voltages or electric fields.
However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this
high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or
VOUT)≤VCC.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused
outputs must be left open.
2
KK74ACT153
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
VCC
Symbol
Parameter
Test Conditions
Guaranteed Limits
V
25 °C
-40°C to
85°C
Unit
VIH
Minimum HighLevel Input Voltage
VOUT=0.1 V or VCC-0.1 V
4.5
5.5
2.0
2.0
2.0
2.0
V
VIL
Maximum Low Level Input Voltage
VOUT=0.1 V or VCC-0.1 V
4.5
5.5
0.8
0.8
0.8
0.8
V
VOH
Minimum HighLevel Output Voltage
IOUT ≤ -50 µA
4.5
5.5
4.4
5.4
4.4
5.4
V
4.5
5.5
3.86
4.86
3.76
4.76
4.5
5.5
0.1
0.1
0.1
0.1
VIN= VIL or VIH
IOL=24 mA
IOL=24 mA
4.5
5.5
0.36
0.36
0.44
0.44
±0.1
±1.0
µA
*
VIN= VIL or VIH
IOH=-24 mA
IOH=-24 mA
VOL
Maximum LowLevel Output Voltage
IOUT ≤ 50 µA
V
*
IIN
Maximum Input
Leakage Current
VIN=VCC or GND
5.5
∆ICCT
Additional Max
ICC/Input
VIN=VCC - 2.1 V
5.5
1.5
mA
IOLD
+Minimum Dynamic
Output Current
VOLD=1.65 V Max
5.5
75
mA
IOHD
+Minimum Dynamic
Output Current
VOHD=3.85 V Min
5.5
-75
mA
ICC
Maximum Quiescent
Supply Current
(per Package)
VIN=VCC or GND
5.5
80
µA
8.0
*
All outputs loaded; thresholds on input associated with output under test.
+Maximum test duration 2.0 ms, one output loaded at a time.
3
KK74ACT153
AC ELECTRICAL CHARACTERISTICS (VCC=5.0 V ± 10%, CL=50pF,Input tr=tf=3.0 ns)
Guaranteed Limits
Symbol
Parameter
25 °C
-40°C to
85°C
Min
Max
Min
Max
Unit
tPLH
Propagation Delay, Input A to Output Y (Figure 2)
3.0
11.5
2.0
13.5
ns
tPHL
Propagation Delay, Input A to Output Y (Figure 2)
3.0
11.5
2.5
13.5
ns
tPLH
Propagation Delay, Strobe to Output Y (Figure 3)
2.0
10.5
2.0
12.5
ns
tPHL
Propagation Delay, Strobe to Output Y (Figure 3)
3.0
9.5
2.5
11.0
ns
tPLH
Propagation Delay, Input D to Output Y (Figure 1)
2.5
9.5
2.0
11.0
ns
tPHL
Propagation Delay, Input D to Output Y (Figure 1)
2.0
9.5
2.0
11.0
ns
CIN
Maximum Input Capacitance
4.5
4.5
pF
Typical @25°C,VCC=5.0 V
CPD
Power Dissipation Capacitance
Figure 1. Switching Waveforms
65
pF
Figure 2. Switching Waveforms
Figure 3. Switching Waveforms
4
KK74ACT153
EXPANDED LOGIC DIAGRAM
5
KK74ACT153
N SUFFIX PLASTIC DIP
(MS - 001BB)
A
Dimension, mm
9
16
Symbol
MIN
MAX
A
18.67
19.69
B
6.1
7.11
B
1
8
5.33
C
F
L
C
D
0.36
0.56
F
1.14
1.78
G
2.54
H
7.62
-T- SEATING
PLANE
N
G
K
M
H
D
J
0.25 (0.010) M T
NOTES:
1. Dimensions “A”, “B” do not include mold flash or protrusions.
Maximum mold flash or protrusions 0.25 mm (0.010) per side.
J
0°
10°
K
2.92
3.81
L
7.62
8.26
M
0.2
0.36
N
0.38
D SUFFIX SOIC
(MS - 012AC)
Dimension, mm
A
16
9
H
B
1
G
P
8
R x 45
C
-TK
D
SEATING
PLANE
J
0.25 (0.010) M T C M
NOTES:
1. Dimensions A and B do not include mold flash or protrusion.
2. Maximum mold flash or protrusion 0.15 mm (0.006) per side
for A; for B ‑ 0.25 mm (0.010) per side.
F
M
Symbol
MIN
MAX
A
9.8
10
B
3.8
4
C
1.35
1.75
D
0.33
0.51
F
0.4
1.27
G
1.27
H
5.72
J
0°
8°
K
0.1
0.25
M
0.19
0.25
P
5.8
6.2
R
0.25
0.5
6