KODENSHI KK74HCT138AD

TECHNICAL DATA
KK74HCT138A
1-of-8 Decoder/Demultiplexer
High-Performance Silicon-Gate CMOS
The KK74HCT138A is identical in pinout to the LS/ALS138. The
KK74HCT138A may be used as a level converter for interfacing TTL or
NMOS outputs to High Speed CMOS inputs.
The KK74HCT138A decodes a three-bit Address to one-of-eight
active-lot outputs. This device features three Chip Select inputs, two
active-low and one active-high to facilitate the demultiplexing, cascading,
and chip-selecting functions. The demultiplexing function is
accomplished by using the Address inputs to select the desired device
output; one of the Chip Selects is used as a data input while the other
Chip Selects are held in their active states.
• TTL/NMOS Compatible Input Levels
• Outputs Directly Interface to CMOS, NMOS, and TTL
• Operating Voltage Range: 4.5 to 5.5 V
• Low Input Current: 1.0 µA
ORDERING INFORMATION
KK74HCT138AN Plastic
KK74HCT138AD SOIC
TA = -55° to 125° C for all packages
PIN ASSIGNMENT
LOGIC DIAGRAM
FUNCTION TABLE
Inputs
PIN 16 =VCC
PIN 8 = GND
Outputs
CS1 CS2 CS3
A2 A1 A0
Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7
X X H
X H X
L X X
X X X
X X X
X X X
H H H H H H H H
H H H H H H H H
H H H H H H H H
H
H
H
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
L
H
L
H
L
H
H
H
H
L
H
H
H
H
L
H
H
H
H
L
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
L
H
H
H
H
L
L
H
H
L
H
L
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
H
H
H
H
L
H
H
H
H
L
H
H
H
H
L
H = high level (steady state)
L = low level (steady state)
X = don’t care
1
KK74HCT138A
MAXIMUM RATINGS*
Symbol
Parameter
Value
Unit
-0.5 to +7.0
V
VCC
DC Supply Voltage (Referenced to GND)
VIN
DC Input Voltage (Referenced to GND)
-1.5 to VCC +1.5
V
DC Output Voltage (Referenced to GND)
-0.5 to VCC +0.5
V
DC Input Current, per Pin
±20
mA
IOUT
DC Output Current, per Pin
±25
mA
ICC
DC Supply Current, VCC and GND Pins
±50
mA
PD
Power Dissipation in Still Air, Plastic DIP+
SOIC Package+
750
500
mW
-65 to +150
°C
260
°C
VOUT
IIN
Tstg
TL
Storage Temperature
Lead Temperature, 1 mm from Case for 10 Seconds
(Plastic DIP or SOIC Package)
*
Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
+Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C
SOIC Package: : - 7 mW/°C from 65° to 125°C
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
VIN, VOUT
Parameter
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to GND)
TA
Operating Temperature, All Package Types
tr, tf
Input Rise and Fall Time (Figure 2)
Min
Max
Unit
4.5
5.5
V
0
VCC
V
-55
+125
°C
0
500
ns
This device contains protection circuitry to guard against damage due to high static voltages or electric fields.
However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this
high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or
VOUT)≤VCC.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused
outputs must be left open.
2
KK74HCT138A
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
VCC
Symbol
Parameter
Test Conditions
Guaranteed Limit
V
25 °C
to
-55°C
≤85
°C
≤125
°C
Unit
VIH
Minimum HighLevel Input Voltage
VOUT=0.1 V or VCC-0.1 V
⎢IOUT⎢≤ 20 µA
4.5
5.5
2.0
2.0
2.0
2.0
2.0
2.0
V
VIL
Maximum Low Level Input Voltage
VOUT=0.1 V or VCC-0.1 V
⎢IOUT⎢ ≤ 20 µA
4.5
5.5
0.8
0.8
0.8
0.8
0.8
0.8
V
VOH
Minimum HighLevel Output Voltage
VIN=VIH or VIL
⎢IOUT⎢ ≤ 20 µA
4.5
5.5
4.4
5.4
4.4
5.4
4.4
5.4
V
VIN=VIH or VIL
⎢IOUT⎢ ≤ 4.0 mA
4.5
3.98
3.84
3.7
VIN=VIH or VIL
⎢IOUT⎢ ≤ 20 µA
4.5
5.5
0.1
0.1
0.1
0.1
0.1
0.1
VIN=VIH or VIL
⎢IOUT⎢ ≤ 4.0 mA
4.5
0.26
0.33
0.4
VOL
Maximum LowLevel Output Voltage
V
IIN
Maximum Input
Leakage Current
VIN=VCC or GND
5.5
±0.1
±1.0
±1.0
µA
ICC
Maximum Quiescent
Supply Current
(per Package)
VIN=VCC or GND
IOUT=0µA
5.5
4.0
40
160
µA
∆ICC
Additional Quiescent
Supply Current
VIN = 2.4 V, Any One Input
VIN=VCC or GND, Other
Inputs
≥-55°C
25°C to
125°C
mA
2.9
2.4
IOUT=0µA
5.5
3
KK74HCT138A
AC ELECTRICAL CHARACTERISTICS (VCC =5.0 V, CL=50pF,Input tr=tf=6.0 ns)
Guaranteed Limit
Symbol
Parameter
25 °C
to
-55°C
≤85°C
≤125°C
Unit
tPLH, tPHL
Maximum Propagation Delay, Input A to
Output Y (Figures 1 and 4)
30
38
45
ns
tPLH, tPHL
Maximum Propagation Delay , CS1 to
Output Y (Figures 2 and 4)
27
34
41
ns
tPLH, tPHL
Maximum Output Transition Time , CS2 or CS3
to Output Y (Figures 3 and 4)
30
38
45
ns
tTLH, tTHL
Maximum Output Transition Time, Any Output
(Figures 2 and 4)
15
19
22
ns
Maximum Input Capacitance
10
10
10
pF
CIN
CPD
Power Dissipation Capacitance (Per Enabled
Output)
Typical @25°C,VCC=5.0 V
Used to determine the no-load dynamic power
consumption:
PD=CPDVCC2f+ICCVCC
51
Figure 1. Switching Waveforms
pF
Figure 2. Switching Waveforms
4
KK74HCT138A
Figure 3. Switching Waveforms
Figure 4. Test Circuit
EXPANDED LOGIC DIAGRAM
5
KK74HCT138A
N SUFFIX PLASTIC DIP
(MS - 001BB)
A
Dimension, mm
9
16
Symbol
MIN
MAX
A
18.67
19.69
B
6.1
7.11
B
1
8
5.33
C
F
L
C
D
0.36
0.56
F
1.14
1.78
G
2.54
H
7.62
-T- SEATING
PLANE
N
G
K
M
H
D
J
0.25 (0.010) M T
NOTES:
1. Dimensions “A”, “B” do not include mold flash or protrusions.
Maximum mold flash or protrusions 0.25 mm (0.010) per side.
J
0°
10°
K
2.92
3.81
L
7.62
8.26
M
0.2
0.36
N
0.38
D SUFFIX SOIC
(MS - 012AC)
Dimension, mm
A
16
9
H
B
1
G
P
8
R x 45
C
-TK
D
SEATING
PLANE
J
0.25 (0.010) M T C M
NOTES:
1. Dimensions A and B do not include mold flash or protrusion.
2. Maximum mold flash or protrusion 0.15 mm (0.006) per side
for A; for B ‑ 0.25 mm (0.010) per side.
F
M
Symbol
MIN
MAX
A
9.8
10
B
3.8
4
C
1.35
1.75
D
0.33
0.51
F
0.4
1.27
G
1.27
H
5.72
J
0°
8°
K
0.1
0.25
M
0.19
0.25
P
5.8
6.2
R
0.25
0.5
6