TECHNICAL DATA Quad 2-Input OR Gate KK74VHCT32 is high-speed logic IC made by CMOS technology and designed for use in high-performance calculating systems with a wide supply voltage range. As for operation speed, KK74VHCT32 can be compared with equivalent bipolar ICs based on Schottky TTL and two times surpasses ICs of KK74НС series. KK74VHCT32 tolerates operation under conditions when voltage on input & output is exceeded up to 7V without affecting characteristics and IC reliability. This possibility allows to use KK74VHCT32 in radio-electronic devices for interfacing with supply voltages 5V and 3V, eliminate IC failure under supply voltage source emergency outage. Use of output edge shaping block in the microcircuit allows to reduce noise amplitude of noises when switching outputs into the same state simultaneously. Input levels of KK74VHCT32 are compatible with TTL level and output levels with CMOS levels. • • • • • • • • • • KK74VHCT32 ORDERING INFORMATION KK74VHCT32N Plastic KK74VHCT32D SOIC TA = -40° to 85° C for all packages Features: Supply voltage range 4.5 to 5.5 V. Output current 8 mA. Low consumption current: 0.2 mkA (typical value) at Та = 25 °С. Latchup current not less than 300 mA at Та = 85 °С. Tolerable value of static potential not less than 2000 V as per human body model (HBM) and not less than 200 V as per machine model (ММ). Ambient operation temperature minus 40 to plus 85 °С. Balanced signal propagation delay. Ensures voltage exceeding mode on input Low noise level at the simultaneous switching of outputs in the same state: VOLP = 0.8 V (max). For pins and functions, compatible with KK74HCT32. . 1 KK74VHCT32 KK74VHCT32 truth table Input Output A B Y= А+В L L L L H H H L H H H Note – H - high voltage level; L - low voltage level; H Pinout A1 01 14 Vcc B1 02 13 B4 Y1 03 12 A4 A2 04 11 Y4 B2 05 10 B3 Y2 06 09 A3 GND 07 08 Y3 Pins description in KK74VHCT32 Pin No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 Symbol А1 В1 Y1 А2 В2 Y2 GND Y3 А3 В3 Y4 А4 В4 VCC Description Input Input Output Input Input Output Common output Output Input Input Output Input Input Supply output from voltage source 2 KK74VHCT32 Absolute maximum conditions* Parameter, unit Supply voltage, V Input voltage, V Output voltage, V Output voltage, V Input diode current, mA Current of common output and supply output, mA Output current, mA Output diode current, mA Dissipated power, mW Symbol VCC Vin Vout Vout1 Iik Icc Value min -0.5 -0.5 -0.5 -0.5 - max 7.0 7.0 VCC + 0.5B 7.0 -20 ±50 ±25 ±20 180 Iout Iok Pd *Under absolute maximum conditions operation of microcircuit is not guaranteed. Operation is guaranteed under maximum conditions Maximum conditions Parameter, unit Supply voltage, V Input voltage,V Output voltage, V Output voltage, V Output current, mA Input rise and fall time, ns/V * - Vcc = 0V Symbol VCC Vin Vout Vout1 Iout tLH, tHL Value min 4.5 0 0 0 0 max 5.5 VCC VCC 5.5* ±8.0 20 3 KK74VHCT32 DC electrical characteristics Value Symbo l Parameter Test conditions max - 4.5 – 5.5 – 0.8 0.8 – 0.8 0.8 VI = VIH or VIL IO = -50 mkA VI = VIH or VIL; IO = -8 mA Low output voltage VI = VIH or VIL IO = 50 mkA VI = VIH or VIL IO = 8 mA Low level input VI = 0 V current High level input VI = VCC current High level input VI = 5.5V current Output bias current VI = 5.5V excess mode Consumption current VI =VCC or 0V 4.5 5.5 4.42 5.42 – – 4.4 5.4 – – 4.5 3.94 – 3.80 – 4.5 5.5 – – 0.09 0.09 – – 0.1 0.1 4.5 – 0.36 – 0.44 5.5 TTL-input VI consumption current 5.5 High input voltage VO ≤ 0.1 V or VO ≥ VCC –0.1 4.5 – 5.5 VIL Low input voltage VO ≤ 0.1 V or VO ≥ VCC –0.1 VOH High output voltage II IIH IIH1 IOPD ICC ICCT –40 to 85 °C min max 2.0 2.0 min 2.0 2.0 VIH VOL 25 °C VCC, V = 3.4 V 5.5 -0.1 V -1.0 5.5 - 0.1 - 1.0 0 - 0.1 - 1.0 0.5 - 5.0 - 2.0 - 20.0 - 1.35 - 1.5 0 Unit uA mA 4 KK74VHCT32 AC electrical characteristics (tLH = tHL = 3.0 ns) Value Symbol Test conditions Parameter tPHL, tPLH Propagation delay time VIL = 0 when switching "on", VIН=3.0 V, "off" CI CРD Input capacity Dynamic capacity CL, pF VCC, V V, 5.0 ± 0.5 VI = 0 V orVCC 15 50 25 °C min – – max 6.9 7.9 5.0 5.0 –40 to 85 °C min max – 8.0 – 9.0 10 28 Unit ns pF Noise characteristics (CL = 50 pF) Parameter Symbol VOLP VOLV VIHD VILD Unit Value VCC, V Positive noise of low output voltage 5.0 Negative noise of low output 5.0 voltage min -0.8 max 0.8 - Input dynamic high voltage Input dynamic low voltage 2.0 0.8 5.0 5.0 V - Time diagram of input and output pulses t LH t HL VCC 0.9 0.9 A, B 0.5 0.1 0.5 0.1 tPLH GND tPHL 0.9 0.9 Y 0.5 0.5 0.1 t TLH t THL 0.1 5 KK74VHCT32 N SUFFIX PLASTIC DIP (MS - 001AA) A Dimension, mm 8 14 B 7 1 Symbol MIN MAX A 18.67 19.69 B 6.1 7.11 5.33 C F L C -T- SEATING PLANE N G M K J H D 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AB) Dimension, mm A 14 8 H B 1 G P 7 R x 45 C -TK D SEATING PLANE M Symbol MIN MAX A 8.55 8.75 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G 1.27 H 5.27 J 0° 8° K 0.1 0.25 1. Dimensions A and B do not include mold flash or protrusion. M 0.19 0.25 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. P 5.8 6.2 R 0.25 0.5 J 0.25 (0.010) M T C M NOTES: F 6