0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Features Matched Pair of Amplifiers for Optimum Balanced Design 0.25 to 3GHz Frequency Range 44 dBm Output IP3 (Balanced configuration) 41 dBm Output IP3 (Single-ended configuration) 15 dB Gain 23 dBm P1dBm 2.1dB Noise Figure RoHS Compliant 4X4 QFN Package Singale Positive Supply +3V to +5V Voltage Rail Absolute Maximum Ratings General Description The CDQ6004-QS is a dual high dynamic range amplifier designed for applications operation within the 0.25 to 3GHz frequency range. Co-located matched amplifiers are assembled in the 4mm X 4mm QFN package. The low-cost, surface-mount, 16 terminal, plastic package is RoHS compliant. The CDQ6004-QS is an ideal solution for implementing balanced or push-pull designs. The amplifier can also be used for dual-band operation where single-ended design is used for each band. The amplifier has the flexibility of being optimized for a number of wireless applications. The combination of low NF and high IP3 at the same bias point make it an ideal transmit or receive solution when used in applications including CATV operating from 50 to 850 MHz, cellular and PCS (personal communications service) operating from 0.8 to 2.2 GHz; MMDS (multichannel multipoint distribution systems) operating from 2.2 to 2.7 GHz; and WLAN (wireless LAN) operation at 2.4 GHz. All devices are 100% RF and DC tested. Supply Voltage RF Input Power Storage Temperature (Tstg) Junction Temperature Operating Temperature Thermal Resistance +6.0 V +20 dBm -55 ºC to +125 ºC 150 ºC -40 ºC to +85ºC 52 ºC/W Operation of this device above any of these parameters may cause damage. Typical Parameters Electrical Characteristics (T = 25ºC) Parameter Typical Frequency Range Gain Input Return Loss Output Return Loss Output IP3 Noise Figure Output P1dB Units 0.9 2 2.4 GHz 16.5 15 14.9 dB -13 -11 -20 dB -16 -12 -11 dB 42 41 40.5 dBm 2.1 2.1 2.6 dB +23 +23 +24 dBm Typical values reflect performance in recommended application circuit @ +5V. Unless otherwise specified, the following specifications are guaranteed at room temerpature in a Mimix fixture. Parameter Frequency Range Gain Input Return Loss Output Return Loss Output IP3 Noise Figure Output P1dB Operating Current Range Supply Voltage Condition Externally Matched Externally Matched Externally Matched Units GHz dB dB dB dBm dB dBm mA V Min. 0.25 13.5 38 120 Typ. 15 -10 -10 41 2.1 23 150 5.0 Max. 3.0 180 Notes: 1. T = 25ºC, Frequency = 2 GHz, 50 Ohm system. 2. Each single ended amplifier is tested separately. 3. OIP3 is measured with two tones at output power of 5 dBm/tone separated by 10 MHz. 4. Slight performance degredation is expected over temperature. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 1 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Typical Device S-Parameters CDQ6004-QS S21 Vs Voltage CDQ6004-QS S12 Vs Voltage 19 0 18 17 16 -5 15 S21 3V S21 4V S21 5V 14 13 S12 3V S12 4V S12 5V -10 12 10 (dB) (dB) 11 9 8 -15 7 -20 6 5 4 3 -25 2 1 0 0 1 2 3 4 5 6 7 8 9 -30 10 0 Frequency (GHz) 1 2 3 4 6 7 8 9 10 9 10 CDQ6004-QS S11 Vs Voltage CDQ6004-QS S22 Vs Voltage 20 10 18 9 16 8 14 7 12 6 S22 3V S22 4V S22 5V 10 8 6 S11 3V S11 4V S11 5V 5 4 3 4 2 2 1 0 (dB) (dB) 5 Frequency (GHz) -2 -4 0 -1 -2 -6 -3 -8 -4 -10 -5 -12 -14 -6 -16 -7 -18 -8 -9 -20 0 1 2 3 4 5 6 Frequency (GHz) 7 8 9 10 -10 0 1 2 3 4 5 6 7 8 Frequency (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 2 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Application Circuit @ 900 MHz Schematic: Typical Performance: CDQ6004-QS Evalua tio n B o ard @ 900MHz VD=5 V 15 20 15 Gain 5 10 5 -5 0 Input Return Loss -5 - 15 - 10 - 15 Output Return Loss -2 0 0 0.5 1 -2 5 1. 5 2 F re q u e n c y ( G H z ) Parameter Board Layout: Frequency Range Gain Input Return Loss Output Return Loss Output IP3 Noise Figure Output P1dB Typical Units 0.9 GHz 16.5 dB -13 dB -16 dB 42 dBm 2.1 dB 23 dBm Components Ref Designator C2, C4, C6, C8 C1, C5 C3, C7 L1, L2 L3, L4 Value Size 2.7 pf 0402 1.5 pf 0603 1000 pf 0805 47 nH 0805 6.8 nH 0603 * Material: FR4, 28 mil * Plating: 1.5 oz. Copper both sides Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 3 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Typical Performance @ 900 MHz (50 Ohm system over voltage) CDQ6004-QS Evaluation Board @ 0.9GHz Input Return Loss (S11) Over Voltage 20 18 16 14 12 10 8 6 4 2 0 Vd=2V Vd=3V Vd=4V Vd=5V Return Loss (dB) Gain (dB) CDQ6004-QS Evaluation Board @ 0.9GHz Gain Over Voltage 0 -5 -10 -15 -20 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 0 0.5 1 1.5 Frequency (GHz) Vd=5V 2 2.5 3 3.5 4 4.5 5 5.5 6 Frequency (GHz) CDQ6004-QS Evaluation Board @ 900MHz P1dB Over Voltage CDQ6004-QS Evaluation Board @ 0.9GHz Output Return Loss (S22) Over Voltage 26 0 24 -5 P1dB (dBm) Return Loss (dB) Vd=3V Vd=4V -25 0 -10 -15 Vd=2V Vd=4V -20 Vd=3V Vd=5V 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 22 20 18 16 14 12 -25 5 5.5 1.5 6 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 5.0 5.5 Drain Voltage (V) Frequency (GHz) CDQ6004-QS Evaluation Board @ 900MHz Noise Figure Over Voltage CDQ6004-QS Evaluation Board @ 900MHz OIP3 Over Voltage 2.4 44 42 40 38 36 34 32 30 28 26 24 2.2 NF(dB) OIP3 (dBm) Vd=2V 2.0 1.8 1.6 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 Drain Voltage (V) Drain Voltage (V) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 4 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Application Circuit @ 1.9 GHz ~ 2.1 GHz: Schematic: Typical Performance: CDQ6 004-QS Evalua tio n B o ard @ 1.9GHz 2.1GHz VD=5 V 20 15 15 Gain 10 5 5 Input Return Loss 0 -5 -5 - 10 - 15 - 15 Output Return Loss -2 0 0 0 .5 1.5 1 2 -2 5 3 2 .5 F re q u e n c y ( G H z ) Parameter Frequency Range Gain Input Return Loss Output Return Loss Output IP3 Noise Figure Output P1dB Board Layout: Typical Units 1.9 2.1 GHz 15.3 15.0 dB -11.9 -12.5 dB -16.3 -13.6 dB dBm 41 41.3 2.1 2.1 dB 23 23 dBm Components Ref Designator C2, C4, C6, C8 C1, C5 C3, C7 L1, L2 Value Size 100 pf 0402 1.5 pf 0603 1000 pf 0805 47 nH 0805 * Material: FR4, 28 mil * Plating: 1.5 oz. Copper both sides Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 5 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Typical Performance @ 1.9 GHz (50 Ohm system over voltage) CDQ6004-QS Evaluation Board @ 1.9~2.1GHz Input Return Loss (S11) Over Voltage 20 18 16 14 12 10 8 6 4 2 0 Vd=2V Vd=3V Vd=4V Vd=5V Return Loss (dB) Gain (dB) CDQ6004-QS Evaluation Board @ 1.9 ~ 2.1 Gain Over Voltage 0 -5 -10 -15 -20 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 0 0.5 1 1.5 Frequency (GHz) Vd=5V 2 2.5 3 3.5 4 4.5 5 5.5 6 Frequency (GHz) CDQ6004-QS Evaluation Board @ 1.9~2.1GHz Output Return Loss (S22) Over Voltage CDQ6004-QS Evaluation [email protected] P1dB Over Voltage 0 26 24 -5 P1dB (dBm) Return Loss (dB) Vd=3V Vd=4V -25 0 -10 -15 Vd=2V Vd=4V -20 Vd=3V Vd=5V 22 20 18 16 14 -25 12 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 1.5 2.0 2.5 Frequency (GHz) 3.0 3.5 4.0 4.5 5.0 5.5 5.0 5.5 Drain Voltage (V) CDQ6004-QS Evaluation Board @ 1.9GHz Noise Figure Over Voltage CDQ6004-QS Evaluation Board @ 1.9GHz OIP3 Over Voltage 2.4 44 42 40 38 36 34 32 30 28 26 24 2.2 NF (dB) OIP3(dBm) Vd=2V 2.0 1.8 1.6 1.5 2.0 2.5 3.0 3.5 4.0 Drain Voltage (V) 4.5 5.0 5.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 Drain Voltage (V) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 6 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Application Circuit @ 2.4 GHz: Schematic: Typical Performance: CDQ6 0 0 4 -QS Eva lua tio n B o a rd @ 2.4 GHz VD=5V 15 20 15 10 5 Gain 5 Input Return Loss -5 0 -5 Output Return Loss - 10 - 15 - 15 -2 0 -2 5 0 0 .5 1 1.5 2 2 .5 3 3 .5 F re q u e n c y ( G H z ) Parameter Frequency Range Gain Input Return Loss Output Return Loss Output IP3 Noise Figure Output P1dB Board Layout: Typical Units 2.4 GHz 14.9 dB -20 dB -11 dB 40.5 dBm 2.6 dB 24 dBm Components Ref Designator C2, C4, C6, C8 C1, C5 C3, C7 L1, L2 Value Size 2.7 pf 0402 1.2 pf 0603 1000 pf 0805 47 nH 0805 * Material: FR4, 28 mil * Plating: 1.5 oz. Copper both sides Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 7 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Typical Performance @ 2.4 GHz (50 Ohm system over voltage) CDQ6004-QS Evaluation Board @ 2.4GHz Input Return Loss (S11) Over Voltage 20 18 16 14 12 10 8 6 4 2 0 Vd=2V Vd=3V Vd=4V Vd=5V Return Loss (dB) Gain (dB) CDQ6004-QS Evaluation Board @ 2.4GHz Gain Over Voltage 0 -5 -10 -15 Vd=2V -20 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 0 0.5 1 1.5 Frequency (GHz) 2 2.5 3 3.5 4 4.5 5 5.5 6 Frequency (GHz) CDQ6004-QS Evaluation Board @ 2.4GHz Output Return Loss (S22) Over Voltage CDQ6004-QS Evaluation Board @ 2.4GHz P1dB Over Voltage 0 26 Output P1dB(dBm) Return Loss (dB) Vd=5V -25 0 -5 -10 -15 Vd=2V Vd=4V -20 Vd=3V Vd=5V -25 24 22 20 18 16 14 12 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 1.5 2.0 2.5 Frequency (GHz) 3.0 3.5 4.0 4.5 5.0 5.5 5.0 5.5 Drain Voltage (V) CDQ6004-QS Evaluation Board @ 2.4GHz OIP3 Over Voltage CDQ6004-QS Evaluation Board @ 2.4GHz Noise Figure Over Voltage 2.8 48 46 44 42 40 38 36 34 32 30 28 26 24 22 2.6 NF(dB) OIP3(dBm) Vd=3V Vd=4V 2.4 2.2 2.0 1.5 2.0 2.5 3.0 3.5 4.0 Drain Voltage (V) 4.5 5.0 5.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 Drain Voltage (V) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 8 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Functional Block Diagram Pin Out Detail Pin Function Description 5 8 16 13 1,2,3,4 9,10,11,12 6,7,14,15 IN 1 Amplifier 1 RF Input IN 2 Amplifier 2 RF Input OUT 1 Amplifier 1 RF Output OUT 2 Amplifier 2 RF Output VS 1 Amplifier 1 Source Connection VS 2 Amplifier 2 Source Connection GND Main Heat-Sinking Connection Physical Dimensions D b K E2 E 100% MATTE TIN e WAFER LOT NUMBER L DATE CODE (YEAR/WEEK) D2 COUNTRY OF ORIGIN (IF OTHER THAN USA) A3 A A2 DIE Ordering Information A A3 A2 b K D E e D2 E2 L MIN 0.80 0 0.25 0.20 2.50 2.50 0.35 NOM 0.90 0.20 REF 0.65 0.30 4.00 BSC 4.00 BSC 0.65 2.65 2.65 0.40 MAX 1.00 1.00 0.35 - 2.80 2.80 0.45 Part Number for Ordering Description CDQ6004-QS-0G00 CDQ6004-QS-0G0T Matte Tin plated RoHS compliant QFN4x4 16L surface mount package in bulk quantity Matte Tin plated RoHS compliant QFN4x4 16L surface mount package in tape and reel PB-CDQ6004-QS-00A0 PB-CDQ6004-QS-00B0 PB-CDQ6004-QS-00C0 CDQ6004-QS Evaluation Board @ 900 MHz CDQ6004-QS Evaluation Board @ 1.9 GHz~2.1 GHz CDQ6004-QS Evaluation Board @ 2.4 GHz We also offer this product with SnPb (Tin-Lead) or NiPdAu plating. Please contact your regional sales manager for more information regarding different plating types. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 9 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier CDQ6004-QS April 2006 - Rev 11-Apr-06 Handling and Assembly Information CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: Do not ingest. Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible with high volume solder installation. Care should be taken not to apply heavy pressure to the top or base material to avoid package damage. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress. Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matt tin (Sn) over copper alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260°C reflow) “Pb Free” processes. Part Numbering Designator - For Mimix/Celeritek lead-free products, the letter “G” will be used in the part number for Matte Tin finished RoHSCompliant components and “L” will be used in the part number of NiPdAu finished RoHS Compliant components in the second position of the part number suffix, as shown below: Example A: CXX1234-XX-0G00 = component bulk quantity Matte Tin finished RoHScompliant parts Example B: CXX1234-XX-0L0T = component in tape and reel NiPdAu finished RoHS parts For those customers not making the change at this time, Mimix/Celeritek will maintain production of current configurations. For questions and comments e-mail: [email protected]. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 10 of 10 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.