19.0-26.0 GHz GaAs MMIC Receiver R1005 April 2006 - Rev 10-Apr-06 Features Sub-harmonic Receiver Integrated LNA, LO Buffer, Image Reject Mixer +2.0 dBm LO Drive Level 2.3 dB Noise Figure 20.0 dB Image Rejection 100% On-Wafer RF, DC and Noise Figure Testing 100% Visual Inspection to MIL-STD-883 Method 2010 Chip Device Layout General Description Mimix Broadband’s 19.0-26.0 GHz GaAs MMIC receiver has a noise figure of 2.5 dB and 20.0 dB image rejection across the band. This device is a two stage balanced LNA followed by an image reject sub-harmonic anti-parallel diode mixer and includes an integrated LO buffer amplifer. The image reject mixer eliminates the need for a bandpass filter after the LNA to remove thermal noise at the image frequency. The use of a sub-harmonic mixer makes the provision of the LO easier than for fundamental mixers at these frequencies. I and Q mixer outputs are provided and an external 90 degree hybrid is required to select the desired sideband. This MMIC uses Mimix Broadband’s 0.15 µm GaAs PHEMT device model technology, and is based upon electron beam lithography to ensure high repeatability and uniformity. The chip has surface passivation to protect and provide a rugged part with backside via holes and gold metallization to allow either a conductive epoxy or eutectic solder die attach process. This device is well suited for Millimeter-wave Point-to-Point Radio, LMDS, SATCOM and VSAT applications. Absolute Maximum Ratings Supply Voltage (Vd) Supply Current (Id1,Id2) Gate Bias Voltage (Vg) Input Power (RF Pin) Storage Temperature (Tstg) Operating Temperature (Ta) Channel Temperature (Tch) +4.5 VDC 180, 165 mA +0.3 VDC 0.0 dBm -65 to +165 OC -55 to MTTF Table 3 MTTF Table 3 (3) Channel temperature affects a device's MTTF. It is recommended to keep channel temperature as low as possible for maximum life. Electrical Characteristics (Ambient Temperature T = 25o C) Parameter Frequency Range (RF) Upper Side Band Frequency Range (RF) Lower Side Band Frequency Range (LO) Frequency Range (IF) Input Return Loss RF (S11)3 Small Signal Conversion Gain RF/IF (S21)2,3 LO Input Drive (PLO) Image Rejection2,3 Noise Figure (NF)2,3 Isolation LO/RF @ LOx1/LOx2 Input Third Order Intercept (IIP3)1,2 Drain Bias Voltage (Vd1) Drain Bias Voltage (Vd2) Gate Bias Voltage (Vg1,2) Supply Current (Id1) (Vd1=3.5V, Vg=-0.3V Typical) Supply Current (Id2) (Vd2=4.0V,Vg=-0.3V Typical) Units GHz GHz GHz GHz dB dB dBm dBc dB dB dBm VDC VDC VDC mA mA Min. 19.0 19.0 8.0 DC 7.5 15.0 -1.2 - Typ. 20.0 9.5 +2.0 20.0 2.3 65.0 -7.0 +4.0 +4.0 -0.3 130 116 Max. 26.0 26.0 14.5 3.0 -12.0 12.0 2.9 +4.5 +4.5 +0.1 155 140 (1) Measured using constant current. (2) Measured using LO Input drive level of +2.0 dBm. (3) Max and Min are specified for RF=20 to 24 GHz Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 1 of 9 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 19.0-26.0 GHz GaAs MMIC Receiver R1005 April 2006 - Rev 10-Apr-06 Receiver Measurements XR1005 LSB Conversion Gain (1398 devices) 12 10 10 8 8 Conversion Gain (dB) Conversion Gain (dB) XR1005 USB Conversion Gain (1398 devices) 12 6 4 2 6 4 2 Max Mean Min 0 Max Mean Min 0 20 21 22 RF at USB (GHz) 23 20 24 22 RF at LSB (GHz) XR1005 USB Image Rejection (1398 devices) 23 24 [IF = 2GHz] XR1005 LSB Image Rejection (1398 devices) 0 0 -5 -5 -10 -10 Image Rejection (dB) Image Rejection (dB) 21 [IF = 2GHz] -15 -20 -25 -30 -15 -20 -25 -30 Max Mean -35 Max Mean -35 -40 -40 20 21 22 RF at USB (GHz) 23 24 20 21 [IF = 2GHz] 22 RF at LSB (GHz) RF Input Return Loss (1398 devices) 23 24 [IF = 2GHz] XR1005 USB Noise Figure (1398 devices) 0 5 4.5 -5 4 3.5 Noise Figure (dB) S11 (dB) -10 -15 3 2.5 2 -20 1.5 1 -25 Max Mean +3sigma Mean -3sigma 0.5 -30 0 20 21 22 RF (GHz) 23 24 20 21 22 RF at USB (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com 23 24 [IF = 2GHz] Page 2 of 9 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 19.0-26.0 GHz GaAs MMIC Receiver R1005 April 2006 - Rev 10-Apr-06 Receiver Measurements (cont.) XR1005 LSB Noise Figure (1398 devices) 5 Typical OIP3 and IIP3 at USB, LO Pin = -2, 0 and +2dBm 4.5 10 4 6 3.5 4 2 OIP3 and IIP3 (dBm) Noise Figure (dB) 8 3 2.5 2 1.5 OIP3 OIP3, LO = -2dBm 0 OIP3, LO = 0dBm -2 -4 OIP3, LO = +2dBm -6 IIP3 -8 IIP3, LO = -2dBm -10 IIP3, LO = 0dBm -12 -14 IIP3, LO = 2dBm -16 1 -18 +3sigma Mean -3sigma 0.5 -20 16 17 18 19 20 21 22 RF USB (GHz) 23 24 25 26 27 28 [IF = 3GHz] 0 20 21 22 RF at LSB (GHz) 23 24 [IF = 2GHz] USB Conversion Gain vs. Pin, IF = 3GHz, LO = +2dBm Typical OIP3 and IIP3 at LSB, LO Pin = -2, 0 and +2dBm 10 20 8 6 21 GHz 16 OIP3, LO = -2dBm 25 GHz 14 0 OIP3, LO = 0dBm -2 -4 OIP3, LO = 2dBm -6 -8 IIP3, LO = -2dBm IIP3 -10 IIP3, LO = 0dBm -12 USB CG (dB) OIP3 and IIP3 (dBm) 18 OIP3 4 2 12 10 8 6 -14 IIP3, LO = 2dBm 4 -16 -18 2 -20 16 17 18 19 20 21 RF LSB (GHz) 22 23 24 25 26 27 0 28 -40 [IF = 3GHz] -38 -36 -34 -32 -30 -28 -26 -24 -22 -20 -18 -16 -14 -12 -10 -8 -6 -4 Pin (dBm) 18-26 GHz USB Conversion Gain (1398 devices) 12 LSB Conversion Gain vs. Pin, IF = 3GHz, LO = +2dBm 20 10 18 21 GHz 16 Conversion Gain (dB) LSB CG (dB) 8 25 GHz 14 12 10 8 6 6 4 4 2 2 Max Mean Min 0 -40 -38 -36 -34 -32 -30 -28 -26 -24 -22 -20 Pin (dBm) -18 -16 -14 -12 -10 -8 -6 -4 0 18 19 20 21 22 RF at USB (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com 23 24 25 [IF = 2GHz] Page 3 of 9 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 26 19.0-26.0 GHz GaAs MMIC Receiver R1005 April 2006 - Rev 10-Apr-06 Receiver Measurements (cont.) 18-26 GHz LSB Conversion Gain (1398 devices) 18-26 GHz USB Image Rejection (1398 devices) 12 0 -5 10 -10 Image Rejection (dB) Conversion Gain (dB) 8 6 4 -15 -20 -25 -30 2 Max Mean Min -35 0 Max Mean -40 18 19 20 21 22 RF at LSB (GHz) 23 24 25 26 18 19 20 [IF = 2GHz] 21 22 RF at USB (GHz) 18-26 GHz LSB Image Rejection (1398 devices) 23 24 25 26 [IF = 2GHz] 18-26 GHz USB Noise Figure (1398 devices) 5 0 4.5 -5 4 -10 Noise Figure (dB) Image Rejection (dB) 3.5 -15 -20 -25 3 2.5 2 1.5 -30 1 Max Mean -35 +3sigma Mean -3sigma 0.5 -40 0 18 19 20 21 22 RF at LSB (GHz) 23 24 25 18 26 19 20 [IF = 2GHz] 21 22 RF at USB (GHz) 18-26 GHz LSB Noise Figure (1398 devices) 23 24 25 26 [IF = 2GHz] 18-26 GHz RF Input Return Loss (1398 devices) 5 0 4.5 -5 4 3.5 S11 (dB) Noise Figure (dB) -10 3 2.5 -15 2 -20 1.5 1 +3sigma Mean -3sigma 0.5 -25 Max Mean 0 -30 18 19 20 21 22 RF at LSB (GHz) 23 [IF = 2GHz] 24 25 26 18 20 22 24 26 RF (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 4 of 9 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 19.0-26.0 GHz GaAs MMIC Receiver R1005 April 2006 - Rev 10-Apr-06 Mechanical Drawing 1.678 (0.066) 2.478 (0.098) 3.278 (0.129) 2 3 4 1.945 (0.077) 1.608 (0.063) 1 1.488 (0.059) 5 10 0.0 0.0 9 1.678 (0.066) 8 7 6 3.077 (0.121) 3.278 (0.129) 2.478 (0.098) 3.677 3.970 (0.145) (0.156) (Note: Engineering designator is 22REC0393) Units: millimeters (inches) Bond pad dimensions are shown to center of bond pad. Thickness: 0.110 +/- 0.010 (0.0043 +/- 0.0004), Backside is ground, Bond Pad/Backside Metallization: Gold All DC/IF Bond Pads are 0.100 x 0.100 (0.004 x 0.004). All RF Bond Pads are 0.100 x 0.200 (0.004 x 0.008). Bond pad centers are approximately 0.109 (0.004) from the edge of the chip. Dicing tolerance: +/- 0.005 (+/- 0.0002). Approximate weight: 4.787 mg. Bond Pad #1 (RF In) Bond Pad #2 (Vd1) Bond Pad #3 (IF1) Bond Pad #4 (Vd2) Bond Pad #5 (LO) Bond Pad #6 (Vg2b) Bond Pad #7 (Vg2) Bond Pad #8 (Vg2a) Bond Pad #9 (IF2) Bond Pad #10 (Vg1) Bias Arrangement Bypass Capacitors - See App Note [2] Vd2 Vd1 Vd1 IF1 2 RF Vd2 IF1 4 3 RF 1 5 LO LO XR1005 10 Vg1 9 IF2 8 7 6 Vg2 IF2 Vg1 Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Vg2 Page 5 of 9 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 19.0-26.0 GHz GaAs MMIC Receiver R1005 April 2006 - Rev 10-Apr-06 App Note [1] Biasing - As shown in the bonding diagram, this device is operated by separately biasing Vd1 and Vd2 with Vd1=4.0V, Id1=130mA and Vd2=4.0V, Id2=116mA. It is also recommended to use active biasing to keep the currents constant as the RF power and temperature vary; this gives the most reproducible results. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current and thus drain voltage. The typical gate voltage needed to do this is -0.3V. Typically the gate is protected with Silicon diodes to limit the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply. App Note [2] Bias Arrangement - Each DC pad (Vd1,2 and Vg1,2) needs to have DC bypass capacitance (~100-200 pF) as close to the device as possible. Additional DC bypass capacitance (~0.01 uF) is also recommended. MTTF Table (TBD) These numbers were calculated based on accelerated life test information and thermal model analysis received from the fabricating foundry. Backplate Temperature Channel Temperature Rth MTTF Hours FITs 55 deg Celsius deg Celsius C/W E+ E+ 75 deg Celsius deg Celsius C/W E+ E+ 95 deg Celsius deg Celsius C/W E+ E+ Bias Conditions: Vd1=4.0V, Vd2=4.0V, Id1=130 mA, Id2=116 mA Typical Application XR1005 BPF RF IN 21.2-23.6 GHz LNA IR Mixer IF Out 2 GHz Coupler AGC Control LO(+2.0dBm) 9.6-10.8 GHz (USB Operation) 11.6-12.8 GHz (LSB Operation) Mimix Broadband MMIC-based 19.0-26.0 GHz Receiver Block Diagram (Changing LO and IF frequencies as required allows design to operate as high as 26.0 GHz) Mimix Broadband's 19.0-26.0 GHz XR1005 GaAs MMIC Receiver can be used in saturated radio applications and linear modulation schemes up to 16 QAM. The receiver can be used in upper and lower sideband applications from 19.0-26.0 GHz. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 6 of 9 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 19.0-26.0 GHz GaAs MMIC Receiver R1005 April 2006 - Rev 10-Apr-06 App Note [3] USB/LSB Selection - LSB USB IF2 For Upper Side Band operation (USB): With IF1 and IF2 connected to the direct port (0º) and coupled port (90º) respectively as shown in the diagram, the USB signal will reside on the isolated port. The input port must be loaded with 50 ohms. For Lower Side Band operation (LSB): With IF1 and IF2 connected to the direct port (0º) and coupled port (90º) respectively as shown in the diagram, the LSB signal will reside on the input port. The isolated port must be loaded with 50 ohms. IF1 An alternate method of Selection of USB or LSB: -90 USB LSB In Phase Combiner In Phase Combiner -90o o IF2 IF1 IF2 IF1 Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 7 of 9 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 19.0-26.0 GHz GaAs MMIC Receiver R1005 April 2006 - Rev 10-Apr-06 Block Diagram Device Schematic Vd1 LNA RF In RF In Vd2 IF1 IR Mixer RF RF Out Vg1 LO Buffer LO LO LO In LO Out Vg2 IF2 LO Buffer Schematic Vd2 R=14.4 R=14.4 R=7.1 R=15.0 R=10.0 R=10.0 LO Out to IR Mixer LO In R=11.4 R=25.0 R=25.0 R=60.0 R=850.0 R=850.0 R=60.0 Vg2a Vg2 Vg2b LNA Schematic R=25.0 Vd1 "LNA arm” VG_1 VD_1 VG_2 VD_2 RF In RF Out R=12.8 R=25.0 RF In R=50.0 R=9.6 R=6.5 R=8.3 RF Out to IR Mixer R=9.6 R=50.0 R=25.0 VG_1 VD_1 VG_2 R=6.5 R=19.2 R=9.6 VD_2 Vg1 Arm "LNA arm” Vg1 Vd1 Arm Vg2 Arm Vd2 Arm R=25.0 Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 8 of 9 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 19.0-26.0 GHz GaAs MMIC Receiver April 2006 - Rev 10-Apr-06 Handling and Assembly Information R1005 CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: Do not ingest. Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ESD - Gallium Arsenide (GaAs) devices are susceptible to electrostatic and mechanical damage. Die are supplied in antistatic containers, which should be opened in cleanroom conditions at an appropriately grounded antistatic workstation. Devices need careful handling using correctly designed collets, vacuum pickups or, with care, sharp tweezers. Die Attachment - GaAs Products from Mimix Broadband are 0.100 mm (0.004") thick and have vias through to the backside to enable grounding to the circuit. Microstrip substrates should be brought as close to the die as possible. The mounting surface should be clean and flat. If using conductive epoxy, recommended epoxies are Ablestick 84-1LMI or 84-1LMIT cured in a nitrogen atmosphere per manufacturer's cure schedule. Apply epoxy sparingly to avoid getting any on to the top surface of the die. An epoxy fillet should be visible around the total die periphery. If eutectic mounting is preferred, then a fluxless gold-tin (AuSn) preform, approximately 0.001 2 thick, placed between the die and the attachment surface should be used. A die bonder that utilizes a heated collet and provides scrubbing action to ensure total wetting to prevent void formation in a nitrogen atmosphere is recommended. The gold-tin eutectic (80% Au 20% Sn) has a melting point of approximately 280 C (Note: Gold Germanium should be avoided). The work station temperature should be 310 C +- 10 C. Exposure to these extreme temperatures should be kept to minimum. The collet should be heated, and the die pre-heated to avoid excessive thermal shock. Avoidance of air bridges and force impact are critical during placement. Wire Bonding - Windows in the surface passivation above the bond pads are provided to allow wire bonding to the die's gold bond pads. The recommended wire bonding procedure uses 0.076 mm x 0.013 mm (0.003" x 0.0005") 99.99% pure gold ribbon with 0.5-2% elongation to minimize RF port bond inductance. Gold 0.025 mm (0.001") diameter wedge or ball bonds are acceptable for DC Bias connections. Aluminum wire should be avoided. Thermo-compression bonding is recommended though thermosonic bonding may be used providing the ultrasonic content of the bond is minimized. Bond force, time and ultrasonics are all critical parameters. Bonds should be made from the bond pads on the die to the package or substrate. All bonds should be as short as possible. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 9 of 9 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.