TM EV3011DQ-00A 1x, 1.5x, 2x High Efficiency Charge Pump 2 White LED Driver Evaluation Board The Future of Analog IC Technology TM DESCRIPTION FEATURES The EV3011DQ-00A is an evaluation board for the MP3011, a fully automatic driver for powering two white LEDs, with up to 4V forward voltage, from a single Li-Ion or three NiMH cells. The driver performs all of the sensing and control to run the LEDs at an optimum charge pump ratio for efficiency without an expensive inductor. The driver allows PWM operation to support brightness control. • • • • • • • • • • • • • The tiny 3mm x 3mm QFN16 package and small external capacitors allow for the most compact white LED solution available. ELECTRICAL SPECIFICATIONS Parameter # of WLEDs Input Voltage LED Current Symbol Value VIN ILED 2 2.5 – 5.5 40 Units V mA 2% LED Current Matching High Efficiency (>93%) Current Source Outputs No Ballast Resistors Required 1x, 1.5x and 2x Automatic Modes Constant Frequency Operation Automatic LED Detection High and Low Frequency PWM Capability 2.5V to 5.5V Operation Less than 1µA Leakage during Shutdown Detects Changes in Battery Level No External Schottky Diode Required Soft-Start and Soft Switching Operation APPLICATIONS • • • Cell Phones PDA or Hand Held Computers White LED Application at 3.6V Supply “MPS” and “The Future of Analog IC Technology” are Trademarks of Monolithic Power Systems, Inc. EV3011DQ-00A EVALUATION BOARD Efficiency vs Supply Voltage 100 90 VLED = 3.35V @ 40mA ILED=10mA ILED=40mA EFFICIENCY (%) 80 70 60 50 ILED=20mA 40 30 20 (L x W x H) 2.4” x 1.9” x 0.4” (6.1cm x 4.8cm x 1.0cm) Board Number MPS IC Number EV3011DQ-00A MP3011DQ EV3011DQ-00A Rev. 1.1 10/27/2005 10 0 2.5 3.0 3.5 4.0 SUPPLY VOLTAGE (V) www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. 4.5 MP3011_EC01 1 TM EV3011DQ-00A – 1X, 1.5X, 2X CHARGE PUMP 2 WHITE LED DRIVER EV BOARD EVALUATION BOARD SCHEMATIC 5, 13 VIN 12 EN 11 3, 10 GND U1 BATT C1A EN C1B RADJ C2A GND C2B LED1 8 TP_LEDC LEDC LED2 4 7 6 9 15 16 MP3011 LED2 LED1 EV3011_S01 EV3011DQ-00A BILL OF MATERIALS Qty Ref 3 C1, C2, C3 1 C4 2 LED1, LED2 1 R1 1.54kΩ Resistor, 1% 0805 1 R2 100kΩ Resistor, 5% 0805 2 R3, R4 1 U1 EV3011DQ-00A Rev. 1.1 10/27/2005 Value Description 1µF Package Manufacturer P/N Distributor P/N TDK: C2012X7R1A105K TDK: C2012X5R0J475K Digikey: 445-1359-1-ND Digikey: 445-1421-1-ND Panasonic: ERJ-6ENF1541V Panasonic: ERJ-6GEYJ104V Yageo: 9C08052A0R00JLHFT MPS: MP3011DQ Digikey: P1.54KCCT-ND Digikey: P100KACT-ND Digikey: 311-0.0ACT-ND Ceramic Cap., 10V, X7R 0805 4.7µF Ceramic Cap., 6.3V, X5R 0805 Not Stuffed 0Ω Resistor, 5% White LED Driver 0805 QFN16 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. 2 TM EV3011DQ-00A – 1X, 1.5X, 2X CHARGE PUMP 2 WHITE LED DRIVER EV BOARD PRINTED CIRCUIT BOARD LAYOUT Figure 1—Top Silk Layer Figure 2—Top Layer Figure 3—Bottom Layer QUICK START GUIDE 1. Solder LED1 – LED2 to the board. 2. Attach the positive and negatives terminals of the power supply (2.5V – 5.5V) to the VIN and GND pins, respectively. 3. Drive EN high to enable the MP3011. Leave EN disconnected to disable the MP3011. 4. To use burst mode brightness control, drive EN with a PWM signal. NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. EV3011DQ-00A Rev. 1.1 10/27/2005 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. 3