NJM2734 Full-Swing Input and Output type Quad Operational Amplifier ■ PACKAGE OUTLINE ■ GENERAL DESCRIPTION NJM2734 is single supply quad operational amplifier with full swing input and output, operates from 1.8V. Input and Output Full Swing provides wide dynamic range, is from ground to power supply level. In addition to ground sensing applications, NJM2734 enable to be applied to Hi-side sensing applications. The features are low noise and low operating voltage for battery management, portable audio applications, and others. ■ FEATURES ●Operating Voltage ●Input Full-Swing ●Output Full-Swing ●Load Drivability ●Offset Voltage ●Slew Rate ●Low Input Voltage Noise ●Adequate phase margin ●Bipolar Technology ●Package Outline :1.8 to 6.0V :VICM= 0 to 5.0V, at V+=5V :VOH≥4.9V/ VOL≤0.1V, at V+=5V, RL=20kΩ :VOH≥4.75V/ VOL≤0.25V, at V+=5V, RL=2kΩ :5mV max. :0.4V/µs typ. :10nV/√Hz typ. :ΦM=75deg. typ., at RL=2kΩ NJM2734D NJM2734M NJM2734E NJM2734V :DIP14, DMP14, EMP14, SSOP14 ■ PIN CONFIGURATION PIN FUNCTION 1. A OUTPUT 2. A -INPUT 3. A +INPUT + 4. V 5. B +INPUT 6. B –INPUT 7. B OUTPUT 8. C OUTPUT 9. C -INPUT 10. A +INPUT 11. GND 12. D +INPUT 13. D –INPUT 14. D OUTPUT NJM2734D NJM2734M NJM2734E NJM2734V Ver.2005-01-26 -1- NJM2734 ■ ABSOLUTE MAXIMUM RATINGS (Ta=25ûC) PARAMETER Supply Voltage Differential Input Voltage Range Common Mode Input Voltage Range SYMBOL + V VID VIC Power Dissipation PD Operating Temperature Range Storage Temperature Range Topr Tstg RATINGS 7.0 ±1.0 (Note1) 0 ~ 7.0 (Note1) (DIP14) 700 (DMP14) 520 (Note2) (EMP14) 720 (Note2) (SSOP14) 450 (Note2) -40~+85 -40~+125 UNIT V V V mW ûC ûC (Note1) For supply voltage less than 7V, the absolute maximum input voltage is equal to the supply voltage. (Note2) On the PCB “ EIA/JEDEC (76.2×114.3×1.6mm, two layers, FR-4) “ ■ RECOMMENDED OPERATING CONDITION (Ta=25ûC) PARAMETER Supply Voltage SYMBOL + V RATING 1.8 to 6.0 UNIT V ■ ELECTRICAL CHARACTERISTICS (V+=5V, Ta=25ûC) ●DC CHARACTERISTICS PARAMETER Operating Current Input Offset Voltage Input Bias Current Input Offset Current Large Signal Voltage Gain Common Mode Rejection Ratio SYMBOL ICC VIO IB IIO AV CMR Supply Voltage Rejection Ratio Maximum Output Voltage 1 SVR VOH1 VOL1 VOH2 VOL2 VICM Maximum Output Voltage 2 Input Common Mode Voltage Range (Note3) TEST CONDITION No signal applied RL=2kΩ to 2.5V CMR+: 2.5V≤VCM ≤5V (Note3) CMR -: 0V≤VCM≤2.5V (Note3) + V /V =±2.0V ~ ±3.0V RL=20kΩ to 2.5V RL=20kΩ to 2.5V RL=2kΩ to 2.5V RL=2kΩ to 2.5V CMR≥55dB (V+=5V, Ta=25ûC) MIN. 60 55 TYP. 1.2 1 50 5 85 70 MAX. 1.8 5 250 100 - UNIT mA mV nA nA dB dB 70 4.9 4.75 0 85 4.95 0.05 4.85 0.15 - 0.1 0.25 5 dB V V V V V CMR is represented by either CMR+ or CMR- has lower value. CMR+ is measured with 2.5V≤VCM≤5.0 and CMR- is measured with 0V≤VCM≤2.5V. (V+=5V, Ta=25ûC) ●AC CHARACTERISTICS PARAMETER Unity Gain Bandwidth Phase Margin Equivalent Input Noise Voltage Amp to Amp Separation SYMBOL GB ΦM VNI CS TEST CONDITION RL=2kΩ to 2.5V RL=2kΩ to 2.5V f=1kHz f=1kHz RL=2kΩ to 2.5V, Vo=1.2Vrms MIN. - TYP. 1 75 10 133 PARAMETER -2- SYMBOL SR UNIT MHz Deg nV/√Hz dB (V+=5V, Ta=25ûC) ●TRANSIENT CHARACTERISTICS Slew Rate MAX. - TEST CONDITION RL=2kΩ to 2.5V MIN. - TYP. 0.4 MAX. - UNIT V/µs Ver.2005-01-26 NJM2734 ■ ELECTRICAL CHARACTERISTICS (V+=3V, Ta=25ûC) ●DC CHARACTERISTICS PARAMETER Operating Current Input Offset Voltage Input Bias Current Input Offset Current Large Signal Voltage Gain Common Mode Rejection Ratio SYMBOL ICC VIO IB IIO AV CMR Supply Voltage Rejection Ratio Maximum Output Voltage 1 SVR VOH1 VOL1 VOH2 VOL2 VICM Maximum Output Voltage 2 Input Common Mode Voltage Range (Note4) TEST CONDITION No signal applied RL=2kΩ to 1.5V CMR+: 1.5V≤VCM≤3V (Note4) CMR -: 0V≤VCM≤1.5V (Note4) + V /V =±1.2V ~ ±2.0V RL=20kΩ to 1.5V RL=20kΩ to 1.5V RL=2kΩ to 1.5V RL=2kΩ to 1.5V CMR≥48dB (V+=3V, Ta=25ûC) MIN. 60 48 TYP. 1 1 50 5 84 63 MAX. 1.8 5 250 100 - UNIT mA mV nA nA dB dB 68 2.9 2.75 0 83 2.95 0.05 2.85 0.15 - 0.1 0.25 3 dB V V V V V CMR is represented by either CMR+ or CMR-has lower value. CMR+ is measured with 1.5V≤VCM≤3.0 and CMR- is measured with 0V≤VCM≤1.5V. (V+=3V, Ta=25ûC) ●AC CHARACTERISTICS PARAMETER Unity Gain Bandwidth Phase Margin Equivalent Input Noise Voltage Amp to Amp Separation SYMBOL GB ΦM VNI CS TEST CONDITION RL=2kΩ to 1.5V RL=2kΩ to 1.5V f=1kHz f=1kHz RL=2kΩ to 1.5V, Vo=0.7Vrms MIN. - TYP. 1 75 10 130 PARAMETER Ver.2005-01-26 SYMBOL SR UNIT MHz Deg nV/√Hz dB (V+=3V, Ta=25ûC) ●TRANSIENT CHARACTERISTICS Slew Rate MAX. - TEST CONDITION RL=2kΩ to 1.5V MIN. - TYP. 0.35 MAX. - UNIT V/µs -3- NJM2734 ■ ELECTRICAL CHARACTERISTICS (V+=1.8V, Ta=25ûC) ●DC CHARACTERISTICS PARAMETER Operating Current Input Offset Voltage Input Bias Current Input Offset Current Large Signal Voltage Gain Common Mode Rejection Ratio SYMBOL ICC VIO IB IIO AV CMR Supply Voltage Rejection Ratio Maximum Output Voltage 1 SVR VOH1 VOL1 VOH2 VOL2 VICM Maximum Output Voltage 2 Input Common Mode Voltage Range (Note5) TEST CONDITION No signal applied RL=2kΩ to 0.9V CMR+: 0.9≤VCM≤1.8V (Note5) CMR-:0V≤VCM≤0.9V (Note5) + - V /V =±0.9V ~ ±1.2V RL=20kΩ to 0.9V RL=20kΩ to 0.9V RL=2kΩ to 0.9V RL=2kΩ to 0.9V CMR≥40dB (V+=1.8V, Ta=25ûC) MIN. 60 40 TYP. 0.9 1 50 5 83 55 MAX. 1.6 5 250 100 - UNIT mA mV nA nA dB dB 65 1.7 1.55 0 80 1.75 0.05 1.65 0.15 - 0.1 0.25 1.8 dB V V V V V CMR is represented by either CMR+ or CMR-has lower value. CMR+ is measured with 0.9V≤VCM≤1.8 and CMR- is measured with 0V≤VCM≤0.9V. (V+=1.8V, Ta=25ûC) ●AC CHARACTERISTICS PARAMETER Unity Gain Bandwidth Phase Margin Equivalent Input Noise Voltage Amp to Amp Separation SYMBOL GB ΦM VNI CS TEST CONDITION RL=2kΩ t o 0.9V RL=2kΩ to 0.9V f=1kHz f=1kHz RL=2kΩ to 0.9V, Vo=0.4Vrms MIN. - TYP. 1 75 10 125 PARAMETER -4- SYMBOL SR UNIT MHz Deg nV/√Hz dB (V+=1.8V, Ta=25ûC) ●TRANSIENT CHARACTERISTICS Slew Rate MAX. - TEST CONDITION RL=2kΩ to 0.9V MIN. - TYP. 0.3 MAX. - UNIT V/µs Ver.2005-01-26 NJM2734 ■ Typical Characteristics Operating Current vs. Supply Voltage Operating Current vs. Ambient Temperature (Ambient Temperature) GV=0dB Ta=85oC 1.4 Ta=25oC Operating Current [uA] 1.4 Operating Current [uA] GV=0dB 1.6 1.6 Ta=125oC 1.2 1 0.8 Ta=-50oC 0.6 Ta=-40oC 0.4 V+=5V 1.2 1 0.8 0.6 V+=1.8V 0.4 0.2 0.2 0 0 0 1 2 3 4 5 Supply Voltage [V] 6 7 -50 -25 (Ambient Temperature) Ta=125oC 3 Ta=85oC Input Offset Voltage [mV] Input Offset Voltage [mV] -0.2 125 GV=0dB GV=0dB 0 0 25 50 75 100 Ambient Temperature [oC] Input Offset Voltage vs. Ambient Temperature Input Offset Voltage vs. Supply Voltage Ta=25oC -0.4 -0.6 Ta=-50oC Ta=-40oC -0.8 2 1 V+=3V + V =5V 0 -1 V+=1.8V -2 -3 -1 0 1 2 3 4 5 Supply Voltage [V] 6 7 -50 Input Offset Current vs. Ambient Temperature -25 0 25 50 75 100 Ambient Temperature [oC] 125 Input Bias Current vs. Ambient Temperature GV=0dB GV=0dB 100 12 8 + 4 V =1.8V Input Bias Current [nA] Input Offset Current [nA] V+=3V V+=3V 0 -4 V+=5V -8 -12 80 V+=5V V+=3V 60 40 V+=1.8V 20 0 -50 Ver.2005-01-26 -25 0 25 50 75 100 Ambient Temperature [oC] 125 -50 -25 0 25 50 75 100 Ambient Temperature [oC] 125 -5- NJM2734 ■ Typical Characteristics Common Mode Rejection Ratio vs. Ambient Temperature Supply Voltage Rejection Ratio vs. Ambient Temperature 90 Common Mode Rejection Ratio [dB] Supply Voltage Rejection Ratio [dB] ≤VICM≤ V+ V+/2≤ GV=0dB 100 V+=4V to 6V 95 90 85 80 75 V+=2.4V to 4V 70 V+=1.8V to 2.4V 65 85 V+=5V 80 75 70 V+=1.8V 65 V+=3V 60 55 50 60 -50 -25 0 25 50 75 100 Ambient Temperature [oC] -50 125 1.0 85 0.5 80 V+=3V 75 V+=5V 70 65 60 0.0 Ta=+85oC -0.5 Ta=+25oC -1.0 -1.5 -2.0 V+=1.8V 55 Ta=-40oC -2.5 50 -3.0 -50 -25 0 25 50 75 100 Ambient Temperature [oC] 125 -1.5 Input Offset Voltage vs. Common Mode Input Voltage -1 -0.5 0 0.5 1 Common Mode Input Voltage [V] V+/V-=±1.5V V+/V-=±2.5V 1.0 0.5 0.5 Input Offset Voltage [mV] Input Offset Voltage [mV] 1.5 Input Offset Voltage vs. Common Mode Input Voltage 1.0 o Ta=+85 C 0.0 -0.5 -1.0 o Ta=+25 C -1.5 Ta=-40oC -2.0 -2.5 0.0 Ta=+85oC -0.5 Ta=+25oC -1.0 Ta=-40oC -1.5 -2.0 -2.5 -3.0 -3.0 -3 -6- 125 V+/V-=±0.9V 0V≤ ≤VICM≤V+/2 Input voltage [mV] Common Mode Rejection Ratio [dB] 0 25 50 75 100 Ambient Temperature [oC] Input Offset Voltage vs. Common Mode Input Voltage Common Mode Rejection ratio vs. Ambient Temperature 90 -25 -2 -1 0 1 2 Common Mode Input Voltage [V] 3 -3 -2 -1 0 1 2 Common Mode Input Voltage [V] 3 Ver.2005-01-26 NJM2734 ■ Typical Characteristics Maximum Output Voltage vs. Load Resistance Input bias Current vs. Common Mode Input Voltage (Ambient Temperature) Ta=+25oC 200 3 Maximum Output Voltage [V] Input Bias Current [nA] 150 V+/V-=±2.5V 100 50 0 V+/V-=±0.9V -50 V+/V-=±1.5V -100 -150 -3 -2 -1 0 1 2 Common Mode Input Voltage [V] 2 1 3 Maximum Output Voltage vs. Load Resistance (Ambient Temperature) V+=3V, GV=OPEN, RL to 1/2V+ 5 Ta=+85oC Ta=+25oC o Ta=-40 C 0 0.01 Ver.2005-01-26 0.1 1 10 Load Resistance [kΩ] 0.1 1 10 Load Resistance [kΩ] 100 (Ambient Temperature) 2 1 Ta=+25oC Maximum Output Voltage vs. Load Resistance Maximum Output Voltage [V] Maximum Output Voltage [V] 3 Ta=+85oC Ta=-40oC 0 0.01 -200 V+=1.8V, GV=OPEN, RL to 1/2V+ 100 V+=5V, GV=OPEN, RL to 1/2V+ 4 3 2 Ta=+85oC Ta=+25oC 1 0 0.01 Ta=-40oC 0.1 1 10 Load Resistance [kΩ] 100 -7- NJM2734 ■ Typical Characteristics Voltage Gain/Phase vs. Frequency Voltage Gain/Phase vs. Frequency (Capacitive Load) (Ambient Temperature) - o V /V =±2.5V, GV=40dB, RL=2kΩ, Ta=+25 C 60 180 60 120 40 V+/V-=±2.5V, GV=40dB, RL=2kΩ, CL=10pF 60 CL=10pF Phase 0 0 -20 -60 -40 CL=1000pF 1k 10k 1M 100k 1000k Frequency [Hz] Gain Ta=+25oC 20 60 -40 -120 -180 10M 10000k -60 1k 10k -180 10M 10000k 1M 100k 1000k Frequency [Hz] Voltage Gain/Phase vs. Frequency (Capacitive Load) (Ambient Temperature) V+/V-=±1.5V, GV=40dB, RL=2kΩ, Ta=+25oC V+/V-=±1.5V, GV=40dB, RL=2kΩ, CL=10pF 180 60 180 gain CL=10pF Phase 0 -20 -60 Ta=+25oC 20 60 Phase 0 Ta=+85oC 0 -20 -60 -120 -40 -120 -180 10M 10000k -60 CL=220pF -40 120 CL=470pF Phase [deg] 60 Ta=-40oC 40 Voltage Gain [dB] 120 Phase [deg] Voltage Gain [dB] 0 -120 20 0 Ta=+85 C -60 Gain 40 o Phase 0 Voltage Gain/Phase vs. Frequency 60 120 Ta=-40oC -20 CL=220pF CL=470pF -60 Voltage Gain [dB] Voltage Gain [dB] 20 Phase [deg] Gain 40 180 Phase [deg] + CL=1000pF -60 1k 10k 1M 100k 1000k Frequency [Hz] 1k Voltage gain/Phase vs. Frequency 10k Voltage Gain/Phase vs. Frequency (Capacitive Load) (Ambient Temperature) V+/V-=±0.9V, GV=40dB, RL=2kΩ, Ta=+25oC 60 -180 10M 10000k 1M 100k 1000k Frequency [Hz] 180 V+/V-=±0.9V, GV=40dB, RL=2kΩ, CL=10pF 60 Gain Gain 40 120 Ta=-40oC 40 180 120 Phase 0 0 -20 -60 CL=220pF -40 CL=470pF 20 60 Phase Ta=+85oC 0 0 -20 -60 -120 -40 -120 -180 10M 10000k -60 Phase [deg] 60 CL=10pF Voltage Gain [dB] 20 Phase [deg] Voltage Gain [dB] Ta=+25oC CL=1000pF -60 1k -8- 10k 1M 100k 1000k Frequency [Hz] 1k 10k 1M 100k 1000k Frequency [Hz] -180 10M 10000k Ver.2005-01-26 NJM2734 ■ Typical Characteristics Voltage Gain vs. Frequency Voltage Gain vs. Frequency (Voltage Follower, Capacitive Load) (Voltage Follower, Ambient Temperature) V+/V-=±2.5V, GV=0dB, RL=2kΩ, Ta=+25oC 15 V+/V-=±2.5V, GV=0dB, RL=2kΩ, CL=10pF 15 10 10 Voltage Gain [dB] Voltage Gain [dB] CL=1000pF CL=470pF 5 CL=220pF 0 CL=10pF -5 -10 5 Ta=-40oC 0 Ta=+25oC -5 Ta=+85oC -10 -15 10k M 100k M 1M 10M Frequency [Hz] -15 10k M 100M 1M 10M Frequency [Hz] Voltage Gain vs. Frequency Voltage Gain vs. Frequency (Voltage Follower, Capacitive Load) (Voltage Follower, Ambient Temperature) V+/V-=±1.5V, GV=0dB, RL=2kΩ, Ta=+25oC 15 100k M V+/V-=±1.5V, GV=0dB, RL=2kΩ, CL=10pF 15 10 100M 10 Voltage Gain [dB] Voltage Gain [dB] CL=1000pF CL=470pF 5 CL=220pF 0 CL=10pF -5 -10 5 Ta=-40oC 0 Ta=+25oC -5 o Ta=+85 C -10 -15 10k M 100k M 1M 10M Frequency [Hz] -15 10k M 100M 100k M 1M 10M Frequency [Hz] 100M Voltage Gain vs. Frequency Voltage Gain vs. Frequency (Voltage Follower, Capacitive Load) (Voltage Follower, Ambient Temperature) V+/V-=±0.9V, GV=0dB, RL=2kΩ, Ta=+25oC V+/V-=±0.9V, GV=0dB, RL=2kΩ, CL=10pF 15 15 10 10 Voltage Gain [dB] Voltage Gain [dB] CL=1000pF CL=470pF 5 CL=220pF 0 CL=10pF -5 -10 5 Ta=-40oC 0 Ta=+25oC -5 o Ta=+85 C -10 -15 -15 M 10k Ver.2005-01-26 M 100k 1M 10M Frequency [Hz] 100M M 10k M 100k 1M 10M Frequency [Hz] 100M -9- NJM2734 ■ Typical Characteristics Pulse Response (Ambient Temperature) Pulse Response (Ambient Temperature) V+=5V, AV=0dB, f=10kHz, VIN=1VPP V+=5V, AV=0dB, f=10kHz, VIN=1VPP RL=2kΩ to V+/2, CL=10pF 3.5 5.0 4.5 2.5 4.0 2.5 4.0 2.0 3.5 2.0 3.5 1.5 3.0 Ta=-40oC Ta=+25oC Ta=+85oC 2.0 OUTPUT 1.0 0.5 2.0 OUTPUT 0.00 0.05 0.10 Time [msec] 0.15 1.5 0.20 0.0 -0.05 0.00 V+=3V, AV=0dB, f=10kHz, VIN=1VPP 4.0 RL=2kΩ to V+/2, CL=1000pF 2.5 INPUT 4.0 INPUT 3.5 2.0 3.5 1.5 3.0 1.5 3.0 1.0 2.5 1.0 2.5 0.5 2.0 Ta=-40oC Ta=+25oC Ta=+85oC 0.0 1.5 -0.5 Input Voltage [V] 2.0 Output Voltage [V] Input Voltage [V] 1.5 0.20 0.15 V+=3V, AV=0dB, f=10kHz, VIN=1VPP RL=2kΩ to V+/2, CL=10pF 2.5 0.05 0.10 Time [msec] Pulse Response (Ambient Temperature) Pulse Response (Ambient Temperature) 1.0 0.5 -1.0 -0.05 Ta=-40 C Ta=+25oC Ta=+85oC 0.0 1.0 OUTPUT 0.05 0.1 Time [msec] 0.15 -1.0 -0.05 0.2 Pulse Response (Ambient Temperature) 0.5 0 RL=2kΩ to V+/2, CL=10pF 1.5 1.5 0.0 Ta=-40oC 1.0 Ta=+25oC Ta=+85oC -0.5 0.5 -1.0 OUTPUT -1.5 -0.05 0 Input Voltage [V] 0.5 Output Voltage [V] 2.5 2.0 RL=2kΩ to V+/2, CL=1000pF 2.0 INPUT 1.0 0.15 0.2 V+=1.8V, AV=0dB, f=10kHz, VIN=1VPP 3.0 1.5 0.05 0.1 Time [msec] Pulse Response (Ambient Temperature) V+=1.8V, AV=0dB, f=10kHz, VIN=1VPP 2.0 1.5 -0.5 0.5 0 2.0 o OUTPUT Input Voltage [V] 2.5 Output Voltage [V] 0.0 -0.05 3.0 Ta=-40oC Ta=+25oC Ta=+85oC 3.0 INPUT 2.5 1.0 2.0 0.5 1.5 0.0 Ta=-40oC 1.0 Ta=+25oC Ta=+85oC -0.5 Output Voltage [V] 0.5 2.5 1.5 Output Voltage [V] 3.0 Input Voltage [V] 4.5 Output Voltage [V] 3.0 1.0 - 10 - 5.0 INPUT INPUT Input Voltage [V] RL=2kΩ to V+/2, CL=1000pF 3.5 0.5 -1.0 OUTPUT 0.05 0.1 0.15 Time [msec] 0.2 0.0 0.25 -1.5 -0.05 0 0.05 0.1 0.15 Time [msec] 0.2 0.0 0.25 Ver.2005-01-26 NJM2734 ■ Typical Characteristics Unity Gain Frequency vs. Capacitive Load Phase Margin vs. Capacitive Load GV=40dB, RF=2kΩ, RG=20Ω, RS=50Ω, Ta=+25oC GV=40dB, RF=2kΩ, RG=20Ω, RS=50Ω, Ta=+25oC 90 1.4 1.2 - V /V =±2.5V 80 V+/V-=±1.5V 70 1 Phase Margin [deg] Unity Gain Frequency [MHz] + 0.8 + - V /V =±0.9V 0.6 0.4 V+/V-=±1.5V V+/V-=±2.5V 60 V+/V-=±0.9V 50 40 30 20 0.2 10 0 0 10 100 1000 Capacitive Load [pF] 10 10000 Amp to Amp Separation vs. Frequency V+/V-=±0.9V, GV=40dB, RL=2kΩ to 0V, RF=100kΩ, o VIN=Ach, Vo=3VPP, Ta=25 C VIN=Ach, Vo=1VPP, Ta=25oC -60 Amp to Amp Separation [dB] Amp to Amp Separation [dB] -60 -80 ACH→CCH ACH→BCH -120 ACH→DCH -140 -160 0.01 0.1 1 10 Frequency [kHz] -80 -100 ACH→CCH -140 -160 0.01 100 Amp to Amp Separation [dB] Amp to Amp Separation [dB] -60 -80 CCH→ACH CCH→BCH -120 -160 0.01 Ver.2005-01-26 CCH→DCH 0.1 1 10 Frequency [kHz] 1 10 Frequency [kHz] 100 V+/V-=±0.9V, GV=40dB, RL=2kΩ to 0V, RF=100kΩ, VIN=Cch, Vo=3VPP, Ta=25oC -140 0.1 Amp to Amp Separation vs. Frequency V+/V-=±2.5V, GV=40dB, RL=2kΩ to 0V, RF=100kΩ, -100 ACH→DCH ACH→BCH -120 Amp to Amp Separation vs. Frequency -60 10000 Amp to Amp Separation vs. Frequency V+/V-=±2.5V, GV=40dB, RL=2kΩ to 0V, RF=100kΩ, -100 100 1000 Capacitive Load [pF] VIN=Cch, Vo=1VPP, Ta=25oC -80 CCH→BCH -100 -120 CCH→DCH -140 CCH→ACH 100 -160 0.01 0.1 1 10 Frequency [kHz] 100 - 11 - NJM2734 ■ Typical Characteristics Total Harmonic Distortion vs. Output Voltage 2 3 1 2 0 1 -1 0 -2 -1 OUTPUT -3 -100 -50 0 Time [µsec] 50 -2 100 Output Voltage [V] Input Voltage [V] INPUT Total Harmonic Distortion (THD+N) [%] Sine Wave Response V+/V-=±1.5V, AV=0dB, VIN=3VPP RL=2kΩ to 0V, f=10kHz, Ta=25°C V+/V-=±1.5V, AV=+2, RL=2kΩ to 0V, CL=0pF, Ta=25°C 10 1 BPF 100Hz : 22Hz to 30kHz 1kHz : 400Hz to 30kHz 10kHz : 400Hz to 80kHz 10kHz 1kHz 0.1 0.01 100Hz 0.001 0.001 0.01 0.1 1 Output Voltage [Vrms] 10 Equivalent Input Noise Voltage vs. Frequency Equivalent Input Noise Voltage [nV/√ Hz] GV=40dB, RL=2kΩ to 0V, CL=10PF, Ta=25oC 30 25 20 V+/V-=±0.9V 15 10 V+/V-=±1.5V 5 V+/V-=±2.5V 0 1 k 10 k 100 k 1k Frequency [Hz] 10k 100k [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. - 12 - Ver.2005-01-26