LM3544 Quad Port USB Power Distribution Switch and Over-Current Protection General Description Features The LM3544 is a quad high-side power switch that is an excellent choice for use in Root, Self-Powered and Bus-Powered USB (Universal Serial Bus) Hubs. Independent port enables, flag signals to alert USB controllers of error conditions, controlled start-up in hot-plug events, and short circuit protection all satisfy USB requirements. The LM3544 accepts input voltages between 2.7V and 5.5V. The Enable logic inputs, available in active-high and active-low versions, can be powered off any voltage in the 2.7V to 5.5V range. The LM3544 limits the continuous current through a single port to 1.25A (max.) when it is shorted to ground. The low on-state resistance of the LM3544 switches ensures the LM3544 will satisfy USB voltage drop requirements, even when current through a switch reaches 500 mA. Thus, High-Powered USB Functions, Low-Powered USB functions, and Bus-Powered USB Hubs can all be powered off a Root or Self-Powered USB Hub containing the LM3544. Added features of the LM3544 include current foldback to reduce power consumption in current overload conditions, thermal shutdown to prevent device failure caused by high-current overheating, and undervoltage lockout to keep switches from operating if the input voltage is below acceptable levels. n n n n n n n n n n n n 90mΩ (typ.) High-Side MOSFET Switch 500mA Continuous Current per Port 7 ms Fault Flag Delay Filters Hot-Plug Events Industry Standard Pin Order Short Circuit Protection with Power-Saving Current Foldback Thermal Shutdown Protection Undervoltage Lockout Recognized by UL and Nemko CB Input Voltage Range: 2.7V to 5.5V 5µA Maximum Standby Supply Current 16-Pin SOIC Package Ambient Temperature Range: −40˚C to 85˚C Applications n USB Root, Self-Powered, and Bus-Powered Hubs n USB Devices such as Monitors and Printers n General Purpose High Side Switch Applications 10120832 10120833 Functional Diagram 10120801 © 2001 National Semiconductor Corporation DS101208 www.national.com LM3544 Quad Port USB Power Distribution Switch and Over-Current Protection March 2001 LM3544 Connection Diagrams LM3544-H 16-Pin SOIC LM3544-L 16-Pin SOIC 10120802 10120829 Top View Top View Ordering Information Part Number Enable, Delivery Option LM3544M-H Active High Enable LM3544M-L Active Low Enable LM3544MX-H Active High Enable, 2500 units per reel LM3544MX-L Active Low Enable, 2500 units per reel Package Type SO-16 NS Package Number M16A Typical Application Circuit 10120804 FIGURE 1. The LM3544 used in a Self-Powered or Root USB Hub www.national.com 2 Lead Temperature Range (Soldering, 5 sec.) (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Voltage at INX and OUTX pins Power Dissipation (Note 2) ESD Rating (Note 3) −0.3V to 6V Voltage at ENX(ENX) and FLAGX pins 260˚C 2 kV Operating Ratings −0.3V to 5.5V Supply Voltage Range Internally Limited Maximum Junction Temperature Storage Temperature Range 2.7V to 5.5V Continuous Output Current Range (Each Output) 150˚C Junction Temperature Range −65˚C to 150˚C 0 mA to 500 mA −40˚C to 125˚C DC Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = 5.0V, ENX = VIN (LM3544-H) or ENX = 0V (LM3544-L). Symbol Parameter Conditions Min Typ Max VIN = 5V, IOUTX = 0.5A 90 125 VIN = 3.3V, IOUTX = 0.5A 95 130 RON On Resistance IOUT OUTX Continuous Output Current 3.0V ≤ VIN ≤ 5.5V ILEAK-OUT OUTX Leakage Current ENX = 0 (ENX = VIN); TJ = 25˚C 0.5 Units mΩ A 0.01 1 µA 10 µA 0.8 1.25 A 2.0 3.2 A ENX = 0 (ENX = VIN); − 40 ≤ TJ ≤ 125˚C ISC OUTX Short-Circuit Current (Note 4) OCTHRESH Overcurrent Threshold VL_FLAG FLAGX Output-Low Voltage I(FLAGX) = 10 mA 0.1 0.3 V ILEAK-FLAG FLAGX Leakage Current 2.7 ≤ VFLAG ≤ 5.5V 0.2 1 µA ILEAK-EN ENx Input Leakage Current ENx/ENx = 0V or ENx/ENx = VIN −0.5 0.5 µA VIH EN/EN Input Logic High 2.7V ≤ VIN ≤ 5.5V 2.4 VIL EN/EN Input Logic Low 4.5V ≤ VIN ≤ 5.5V 0.8 V 2.7V ≤ VIN ≤ 4.5V 0.4 V VUVLO IDDON IDDOFF OUTX Connected to GND Under-Voltage Lockout Threshold Operational Supply Current Shutdown Supply Current V 1.8 600 µA ENx = VIN (ENx = 0 ); −40˚C ≤ TJ ≤ 125˚C 800 µA ENx = 0 (ENx = VIN); TJ = 25˚C 1 µA −40˚C ≤ TJ ≤ 125˚C 5 µA ENx = VIN (ENx = 0 ); TJ = 25˚C 375 V Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its rated operating conditions. Note 2: The maximum allowable power dissipation is a function of the Maximum Junction Temperature (TJMAX), Junction to Ambient Thermal Resistance (θJA), and the Ambient Temperature (TA). The LM3544 in the 16-pin SOIC package has a TJMAX of 150˚C and a θJA of 130˚C/W. The maximum allowable power dissipation at any temperature is PMAX = (TJMAX − TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the part will go into thermal shutdown. Note 3: The Human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. Note 4: Thermal Shutdown will protect the device from permanent damage. 3 www.national.com LM3544 Absolute Maximum Ratings LM3544 AC Electrical Characteristics Limits are for TJ = 25˚C and VIN = 5.0V. Symbol Parameter Conditions Min Typ Max Units tr OUTx Rise Time (Note 5) CL = 33 µF, ILOAD = 500 mA 1.5 ms tf OUTx Fall Time (Note 6) CL = 33 µF, ILOAD = 500 mA 0.9 ms tON Turn-on Delay (Note 7) CL = 33 µF, ILOAD = 500 mA 2.9 ms tOFF Turn-off Delay (Note 8) CL = 33 µF, ILOAD = 500 mA 0.7 ms Flag Delay (Note 9) IFLAG = 10 mA 7 ms tF Note 5: Time for OUTx to rise from 10% to 90% of its enabled steady-state value after ENx (ENx) is asserted. Note 6: Time for OUTx to fall from 10% to 90% of its enabled steady-state value after ENx (ENx) is deasserted. Note 7: Time between ENx rising through VIH (ENx falling through VIL) and OUTx rising through 90% of its enabled steady-state voltage. Note 8: Time between ENx falling through VIL (ENx rising through VIH) and OUTx falling through 10% of its enabled steady-state voltage. Note 9: Time between ENx rising through VIN (ENx falling through VIN) and FLAGX falling through 0.3V when OUTX is connected to GND. Pin Description Pin Number Pin Name Pin Function 2, 6 IN 1, 2 Supply Inputs: These pins are the inputs to the power switches and the supply input for the IC. In most applications they are connected together externally and to a single input voltage supply. 1, 5 GND 1, 2 15, 14, 11, 10 OUT 1, 2, 3, 4 3, 4, 7, 8 LM3544-H: EN 1, 2, 3, 4 (LM3544-L: EN 1, 2, 3, 4) 16, 13, 12, 9 FLAG 1, 2, 3, 4 www.national.com Grounds: Must be connected together and to a common ground. Switch Outputs: These pins are the outputs of the high side switches. Enable (Inputs): Active-high (or active-low) logic enable inputs. Fault Flag (Outputs): Active-low open drain outputs. Indicates over-current, UVLO or thermal shutdown. See ″Application Information″ section for more details. 4 VIN = 5.0, IOUT_X = 500mA, TA = 25˚C unless otherwise specified. RON vs Input Voltage RON vs Junction Temperature 10120806 10120805 Quiescent Current, Output(s) Enabled vs Junction Temperature Quiescent Current, Output(s) Disabled vs Junction Temperature 10120808 10120807 Quiescent Current, Output(s) Enabled vs Input Voltage Quiescent Current, Output(s) Disabled vs Input Voltage 10120810 10120809 5 www.national.com LM3544 Typical Performance Characteristics LM3544 Typical Performance Characteristics VIN = 5.0, IOUT_X = 500mA, TA = 25˚C unless otherwise specified. (Continued) Short-Circuit Output Current vs Junction Temperature (Note 10) Over-Current Threshold vs Junction Temperature (Note 10) 10120813 10120814 Under-Voltage Lockout (UVLO) Threshold vs Junction Temperature Turn-On Delay vs Input Voltage (CIN = 33 µF, COUT = 33 µF) 10120815 10120811 Turn-Off Delay vs Input Voltage (CIN = 33 µF, COUT = 33 µF) Fault Flag Delay Time vs Junction Temperature 10120812 www.national.com 10120816 6 VIN = 5.0, IOUT_X = 500mA, TA = 25˚C unless otherwise specified. (Continued) Turn-On/Turn-Off Response with 47Ω/33µF Load Turn-On/Turn-Off Response with 10Ω/33µF Load 10120818 10120819 Enable Into a Short (Note 10) Short Connected to Enabled Device (Note 10) 10120820 10120821 Over-Current Response with Ramped Load on OUT1 and Fixed Load on OUT2 (Note 10) Inrush Current to Downstream Device when LM3544 is Enabled (Note 11) 10120822 10120823 Note 10: Output is shorted to Ground through a 100 mΩ resistor. Note 11: Load is two capacitors and one resistor in parallel to model an actual USB load condition. The first capacitor has a value of 33 µF to model the LM3544 output capacitor. The second capacitor has a value of 10 µF to model the maximum allowable input capacitance of the downstream device. The resistor is a 47Ω resistor to model the maximum allowable input resistance of the downstream device. 7 www.national.com LM3544 Typical Performance Characteristics LM3544 rapidly discharge through the part, activating current limit circuitry. The threshold for activating current limiting is 2.0A (typ.). Protection is achieved by momentarily opening the MOSFET switch and then gradually turning it on. Turn-on is halted when the current through the switch reaches the current-limit level of 1.0A (typ.) The current is held at this level until either the excessive load/short is removed or the part overheats and thermal shutdown occurs (see Thermal Shutdown section, below). The fault flag of a switch is asserted whenever the switch is current limiting. If a port on the LM3544 is enabled into a short condition, the output current of that port will rise to the current-limit level and hold there. When a port is in a current-limit condition, the LM3544 senses the output voltage on that port and, if it is less than 1.0V (typ.), will reduce the output current through that port. This operation is shown in Figure 2, below. The current reduction, or foldback, reduces power dissipation through the overloaded MOSFET switch. An additional advantage of the foldback feature is the reduction of power required from the source supply when one or more output ports are shorted. Functional Description Power Switches The power switches that comprise the four ports of the LM3544 are N-Channel MOSFETs. They have a typical on-state drain-to-source resistance of 90 mΩ when the input voltage is 5 V. When enabled, each switch will supply a 500 mA minimum current to its load. In the unlikely event that a switch is enabled and the output voltage of that switch is pulled above the input voltage, the bi-directional nature of the switch results in current to flow from the output to the input. When a switch is disabled, current flow through the switch is prevented in both directions. Charge Pump and Driver The gate voltages of the high-side NFET power switches are supplied by an internal charge-pump and driver circuit combination. The charge pump is a low-current switched-capacitor circuit that efficiently generates voltages above the LM3544 input supply. The charge pump output is used to supply a transconductance amplifier driver circuit that controls the gate voltages of the power switches. Rise and fall times on the gates are typically kept between 2 ms and 4 ms to limit large current surges and associated electromagnetic interference (EMI). ENABLE (ENx or ENx) The LM3544 comes in two versions: an active-high enable version, LM3544-H, and an active-low enable version, LM3544-L. In the LM3544-H, the ENx pins are active-high logic inputs that, when asserted, turn on the associated power supply switch(es). Power supply switches are controlled by the ENx active-low logic inputs in the LM3544-L. With all four ports disabled on either version of the LM3544, less than 5 µA of supply current is consumed. Both types of enable inputs, active-high and active-low, are TTL and CMOS logic compatible. Input and Output The power supply to the control circuitry and the drains of the power-switch MOSFETs are connected to the two input pins, IN1 and IN2. These two pins are connected externally in most standard applications. The two ground nodes GND1 and GND2 must be connected externally in all applications. Pins OUT1, OUT2, OUT3, and OUT4 are connections to the source nodes of the power-switch MOSFETs. In a typical application circuit, current flows through the switches from IN1 and IN2 to OUTx toward the load. 10120817 FIGURE 2. Short-Circuit Output Current (with Foldback) vs. Output Voltage Thermal Shutdown The LM3544 is internally protected against excessive power dissipation by a two-stage thermal protection circuit. If the device temperature rises to approximately 145˚C, the thermal shutdown circuitry turns off any switch that is current limited. Non-overloaded switches continue to function normally. If the die temperature rises above 160˚C, all switches are turned off and all four fault flag outputs are activated. Hysteresis ensures that a switch turned off by thermal shutdown will not be turned on again until the die temperature is reduced to 135˚C. Shorted switches will continue to cycle off and on, due to the rising and falling die temperature, until the short is removed. The thermal shutdown function is shown graphically in Figure 3 and Figure 4. Undervoltage Lockout (UVLO) Undervoltage Lockout (UVLO) prevents the MOSFET switches from turning on until the input voltage exceeds a typical value of 1.8V. If the input voltage drops below the UVLO threshold, the MOSFET switches are opened and fault flags are activated. UVLO flags function only when one or more of the ports is enabled. If a port is enabled in a UVLO condition, flags corresponding to the enabled port and its dual (port 1 is paired with port 2, port 3 is paired with port 4) are asserted. Current Limit and Foldback The current limit circuit is designed to protect the system supply, the LM3544 switches, and the load from potential damage resulting from excessive currents. If a direct short occurs on an output of the LM3544, the input capacitor(s) www.national.com 8 Soft Start (Continued) When a power switch is enabled, high levels of current will flow instantaneously through the LM3544 to charge the large capacitance at the output of the port. This is likely to exceed the over-current threshold of the device, at which point the LM3544 will enter its current-limit mode. The amount of current used to charge the output capacitor is then set by the current-limit circuitry. The device will exit the current-limit mode when the current needed to continue to charge the output capacitor is less than the LM3544 current-limit level. Fault Flag The fault flags are open-drain outputs, each capable of sinking up to a 10 mA load current to typically 100 mV above ground. A parasitic diode exists between the flag pins and VIN pins. Pulling the flag pins to voltages higher than VIN will forward bias this diode and will cause an increase in supply current. This diode will also clamp the voltage on the flag pins to a diode drop above VIN. The fault flag is active (pulled low) when any of the following conditions are present: under-voltage, current-limit, or thermal-shutdown. The LM3544 has an internal delay in reporting fault conditions that is typically 7 ms in length. In start-up, the delay gives the device time to charge the output capacitor(s) and exit the current-limit mode before a flag signal is set. This delay also prevents flag signal glitches from occurring when brief changes in operating conditions momentarily place the LM3544 into one of its three error conditions. If an error condition still exists after the delay interval has elapsed, the appropriate fault flag(s) will be asserted (pulled low) until the error condition is removed. In most applications, the 7 ms internal flag delay eliminates the need to extend the delay with an external RC delay network. 10120825 FIGURE 3. Thermal Shutdown Characteristics when only the First-Stage Thermal-Shutdown Mode is Needed Application Information 10120826 Output Filtering The schematic in Figure 1 showed a typical application circuit for the LM3544. The USB specification requires 120 µF at the output of each hub. A four-port hub with 33 µF tantalum capacitors at each port output meets the specification. These capacitors provide short-term transient current to drive downstream devices when hot-plug events occur. Capacitors with low equivalent-series-resistance should be used to lower the inrush current flow through the LM3544 during a hot-plug event. The rapid change in currents seen during a hot plug event can generate electromagnetic interference (EMI). To reduce this effect, ferrite beads in series between the outputs of the LM3544 and the downstream USB port are recommended. Beads should also be placed between the ground node of the LM3544 and the ground nodes of connected downstream ports. In order to keep voltage drop across the beads to a minimum, wire with small DC resistance should be used through the ferrite beads. A 0.01 µF - 0.1 µF ceramic capacitor is recommended on each downstream port directly between the Vbus and ground pins to further reduce EMI effects. FIGURE 4. Thermal Shutdown Characteristics when Both First-Stage and Second-Stage Thermal-Shutdown Modes are Needed In Figure 3, port 1 is enabled into a short. When this occurs, the MOSFET switch of port 1 repeatedly opens and closes as the device temperature rises and falls between 145˚C and 135˚C. In this example, the device temperature never rises above 160˚C. The second stage thermal shutdown is not used and port 2 remains operational. When port 1 is enabled into a short in the example illustrated in Figure 4, the device temperature immediately rises above 160˚C. A higher ambient temperature or a larger number of shorted outputs can cause the junction temperature to increase, resulting in the difference in behavior between the current example and the previous one. When the junction temperature reaches 160˚C, all four ports are disabled (ports 3 and 4 are not shown in the figure) and all four fault-flag signals are asserted. Just prior to time index 2.5 ms, the device temperature falls below 135˚C, all four ports activate, and all four fault flags are removed. The short condition remains on port 1, however. For the remainder of the example, the device temperature cycles between 135˚C and 145˚C, causing port 1 to repeatedly turn on and off but allowing the un-shorted ports to function normally. Power Supply Filtering A sizable capacitor should be connected to the input of the LM3544 to ensure the voltage drop on this node is less than 330 mV during a heavy-load hot-plug event. A 33 µF, 16V 9 www.national.com LM3544 Functional Description LM3544 Application Information Performance Characteristics section of this datasheet. Next, calculate the power dissipation through the switch with Equation (1). (Continued) tantalum capacitor is recommended. The input supply should be further bypassed with a 0.01 µF - 0.1 µF ceramic capacitor, placed close to the device. The ceramic capacitor reduces ringing on the supply that can occur when a short is present at the output of a port. PD = RON * IDS2 (1) Note: Equation for power dissipation neglects portion that comes from LM3544 quiescent current because this value will almost always be insignificant. Using this figure, determine the junction temperature with Equation (2). TJ = PD * θJA + TA. (2) Extending the Fault Flag Delay While the 7 ms (typical) internal delay in reporting flag conditions is adequate for most applications, the delay can be extended by connecting external RC filters to the FLAG pins, as shown in Figure 5. Where: θJA = SOIC Thermal Resistance: 130˚C/W and TA = Ambient Temperature (˚C). Compare the calculated temperature with the expected temperature used to estimate RON. If they do not reasonably match, re-estimate RON using a more appropriate operating temperature and repeat the calculations. Reiterate as necessary. PCB Layout Considerations In order to meet the USB requirements for voltage drop, droop and EMI, each component used in this circuit must be evaluated for its contribution to the circuit performance. These principles are illustrated in Figure 6. The following PCB layout rules and guidelines are recommended 1. Place the switch as close to the USB connector as possible. Keep all Vbus traces as short as possible and use at least 50-mil, 1 ounce copper for all Vbus traces. Solder plating the traces will reduce the trace resistance. 2. Avoid vias as much as possible. If vias are used, use multiple vias in parallel and/or make them as large as possible. 3. Place the output capacitor and ferrite beads as close to the USB connector as possible. 4. If ferrite beads are used, use wires with minimum resistance and large solder pads to minimize connection resistance. 10120828 FIGURE 5. Typical Circuit for Lengthening the Internal Flag Delay Power Dissipation and Junction Temperature A few simple calculations will allow a designer to calculate the approximate operating temperature of the LM3544 for a given application. The large currents possible through the low resistance power MOSFET combined with the high thermal resistance of the SOIC package, in relation to power packages, make this estimate an important design step. Begin the estimate by determining RON at the expected operating temperature using the graphs in the Typical 10120827 FIGURE 6. Self-Powered Hub Connections and Per-Port Voltage Drop www.national.com 10 USB Bus-Powered Functions and General In-Rush Current Limiting Applications Root and Self-Powered USB Hubs The LM3544 can be placed at the power-supply input of USB bus-powered functions, or other similar devices, to protect them from high in-rush currents. If the current being delivered to the device were to exceed the 2.0A over-current threshold (typ.) of the LM3544, switches in violation would open to protect the device from damage. In addition to in-rush current limiting, the LM3544 can be used in high-power bus-powered functions to keep current levels of the function in compliance during power-up. The USB specification requires the staged switching of power when connecting high-power functions to the bus. When a high-power function is initially connected to the bus, it must not draw more than one unit supply (100mA). After a connection is detected and enumerated, and if the upstream device is capable of supplying the required power, the high-power function may draw up to five unit loads (500mA). With the proper control signals, the LM3544 can be used to achieve this staged power connection. When the function is connected to the bus, one or more of the LM3544 switches can be closed to connect bus power only to circuitry needed during the connection and enumeration process. If the function is to be powered fully, remaining switches on the LM3544 can be closed to connect all blocks of the function to the power bus. Figure 7 illustrates how the LM3544 can be connected for use in bus powered functions. The LM3544 has been designed primarily for use in root and self-powered USB hubs. In this application, the switches of the LM3544 are used to connect the power source of the hub to the power bus used by downstream devices and to protect the hub from dangerously excessive loads and shorts to ground. A high-power bus-powered function, low-power bus-powered function, or a bus-powered hub can be driven through a single port of the LM3544. A schematic of a circuit that uses the LM3544 for power-supply switching in a typical root or self-powered hub was shown earlier in this datasheet in Figure 1. Voltage drop requirements of USB power supplies require the power outputs of the root and self-powered hubs to be no less than 4.75V. For this reason, it is recommended that a 5V power supply with a ± 3% output voltage tolerance is used in this application. Combining a 3% supply with a low-resistance PCB design and the low on-resistance of the LM3544 power switches will ensure that the hub power outputs meet the USB voltage drop specification even with a 500mA load, the maximum allowed in the USB standard. Bus-Powered USB Hubs The LM3544 is capable of performing the power supply switching functions required in Bus-Powered hubs. Use here is very similar to the configuration used in root and self-powered hubs. With bus-powered hubs, however, there is no internal power supply to drive the input pins of the LM3544. Instead, the input pins should be connected to the power bus supplied by the upstream hub. 10120831 FIGURE 7. Using the LM3544 in USB Bus-Powered Functions auxiliary supply, used when the device is in suspend mode, can dramatically decrease the power consumption of a computer that contains devices that spend extended periods of time in suspend mode. This application also works especially well with devices configured for remote wakeup capabilities (i.e.: using a keystroke on a mouse or keyboard Wake-on-USB and Remote Wakeup Applications The LM3544 can be used in desktop and notebook PC based root hubs to switch the power connection of USB devices between the main power source, used when the device is active, and a reduced power auxiliary supply. The 11 www.national.com LM3544 Typical Applications LM3544 Typical Applications In order to allow the power-switching circuit to smoothly transition from one supply to another, delay networks must be placed before the enable pins. These delay networks account for the turn-on delay of the LM3544 switches by slowing the fall time of the enable signals. Rise times of these signals are not affected by the delay networks. Glitch free transition is assured as long as both supplies remain within operating specifications for a minimum of 5 ms after the logic signal SRC is toggled. (Continued) to awaken a suspended PC). A schematic showing an example of how the LM3544 can be configured to switch the power connection of a device between two separate sources is shown in Figure 8, below. In the example, the logic signals EN and SRC control the power supply connections. If the EN signal is low, all four LM3544 switches will be open and neither supply will be connected to the bus. If EN and SRC are both high, switch 1 and switch 3 close, connecting the main power supply to the two bus power outputs. When EN is high and SRC is low, the auxiliary supply is connected to the power outputs through switches 2 and 4. 10120830 FIGURE 8. Using the LM3544 in a Wake-on-USB Application www.national.com 12 inches (millimeters) unless otherwise noted Order Number LM3544M-H, LM3544M-L, LM3544MX-H or LM3544MX-L, NS Package Number M16A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM3544 Quad Port USB Power Distribution Switch and Over-Current Protection Physical Dimensions