LM9036 Ultra-Low Quiescent Current Voltage Regulator General Description Features The LM9036 ultra-low quiescent current regulator features low dropout voltage and low current in the standby mode. With less than 25µA Ground Pin current at a 0.1mA load, the LM9036 is ideally suited for automotive and other battery operated systems. The LM9036 retains all of the features that are common to low dropout regulators including a low dropout PNP pass device, short circuit protection, reverse battery protection, and thermal shutdown. The LM9036 has a 40V maximum operating voltage limit, a −40˚C to +125˚C operating temperature range, and ± 5% output voltage tolerance over the entire output current, input voltage, and temperature range. n Ultra low Ground Pin current (IGND ≤ 25µA for IOUT = 0.1mA) n Fixed 5V, 3.3V, 50mA output n Output tolerance ± 5% over line, load, and temperature n Dropout voltage typically 200mV @ IOUT = 50mA n −45V reverse transient protection n Internal short circuit current limit n Internal thermal shutdown protection n 40V operating voltage limit Typical Application 20001101 * Required if regulator is located more than 2" from power supply filter capacitor. ** Required for stability. Must be rated over intended operating temperature range. Effective series resistance (ESR) is critical, see Electrical Characteristics. Locate capacitor as close as possible to the regulator output and ground pins. Capacitance may be increased without bound. © 2004 National Semiconductor Corporation DS200011 www.national.com LM9036 Ultra-Low Quiescent Current Voltage Regulator April 2004 Connection Diagrams TO-252 20001125 Top View Order Number LM9036DT-5.0, LM9036DT-3.3 See NS Package Number TD03B 20001127 20001128 Top View LM9036MM-3.3, LM9036MM-5.0 See NS Package Number MUA08A www.national.com Top View LM9036M-3.3, LM9036M-5.0 See NS Package Number M08A 2 Absolute Maximum Ratings (Note 1) Operating Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Input Voltage (Survival) Operating Temperature Range +55V, −45V ESD Susceptibility (Note 2) ± 1.9kV Power Dissipation (Note 3) Internally limited Junction Temperature (TJmax) Storage Temperature Range 150˚C −65˚C to +150˚C Lead Temperature (Soldering, 10 sec.) −40˚C to +125˚C Maximum Input Voltage (Operational) 40V SO-8 (M08A) θJA (Note 7) 140˚C/W TO-252 (TD03B) θJA (Note 7) 125˚C/W TO-252 (TD03B) θJA (Note 8) 50˚C/W TO-252 (TD03B) θJC (Note 7) 11˚C/W MSO-8 (MUA08A) θJA (Note 7) 200˚C/W 260˚C Electrical Characteristics - LM9036-5.0 VIN = 14V, IOUT = 10 mA, TJ = 25˚C, unless otherwise specified. Boldface limits apply over entire operating temperature range Parameter Output Voltage (VOUT) Quiescent Current (IGND) Line Regulation (∆ VOUT) Load Regulation (∆ VOUT) Dropout Voltage (∆ VOUT) Conditions 5.5V ≤ VIN ≤ 26V, 0.1mA ≤ IOUT ≤ 50mA (Note 6) Min (Note 5) Typical (Note 4) Max (Note 5) 4.80 5.00 5.20 4.75 5.00 5.25 IOUT = 0.1mA, 8V ≤ VIN ≤ 24V 20 25 IOUT = 1mA, 8V ≤ VIN ≤ 24V 50 100 IOUT = 10mA, 8V ≤ VIN ≤ 24V 0.3 0.5 IOUT = 50mA, 8V ≤ VIN ≤ 24V 2.0 2.5 6V ≤ VIN ≤ 40V, IOUT = 1mA 10 30 Units V µA mA mV 0.1mA ≤ IOUT ≤ 5mA 10 30 mV 5mA ≤ IOUT ≤ 50mA 10 30 mV IOUT = 0.1mA 0.05 0.10 V IOUT = 50mA 0.20 0.40 V 250 mA Short Circuit Current (ISC) VOUT = 0V 65 120 Ripple Rejection (PSRR) Vripple = 1Vrms, Fripple = 120Hz −40 −60 dB Output Bypass Capacitance (COUT) 0.3Ω ≤ ESR ≤ 8Ω 0.1mA ≤ IOUT ≤ 50mA 10 22 µF Electrical Characteristics - LM9036-3.3 VIN = 14V, IOUT = 10 mA, TJ = 25˚C, unless otherwise specified. Boldface limits apply over entire operating temperature range Parameter Output Voltage (VOUT) Quiescent Current (IGND) Conditions 5.5V ≤ VIN ≤ 26V, 0.1mA ≤ IOUT ≤ 50mA (Note 6) Min (Note 5) Typical (Note 4) Max (Note 5) 3.168 3.30 3.432 3.135 3.30 3.465 IOUT = 0.1mA, 8V ≤ VIN ≤ 24V 20 25 IOUT = 1mA, 8V ≤ VIN ≤ 24V 50 100 IOUT = 10mA, 8V ≤ VIN ≤ 24V 0.3 0.5 IOUT = 50mA, 8V ≤ VIN ≤ 24V 2.0 2.5 Units V µA mA Line Regulation (∆ VOUT) 6V ≤ VIN ≤ 40V, IOUT = 1mA 10 30 mV Load Regulation (∆ VOUT) 0.1mA ≤ IOUT ≤ 5mA 10 30 mV 5mA ≤ IOUT ≤ 50mA 10 30 mV Dropout Voltage (∆ VOUT) IOUT = 0.1mA 0.05 0.10 V IOUT = 50mA 0.20 0.40 V 3 www.national.com Electrical Characteristics - LM9036-3.3 (Continued) VIN = 14V, IOUT = 10 mA, TJ = 25˚C, unless otherwise specified. Boldface limits apply over entire operating temperature range Parameter Min (Note 5) Conditions Typical (Note 4) Max (Note 5) Units 250 mA Short Circuit Current (ISC) VOUT = 0V 65 120 Ripple Rejection (PSRR) Vripple = 1Vrms, Fripple = 120Hz −40 −60 dB Output Bypass Capacitance (COUT) 0.3Ω ≤ ESR ≤ 8Ω 0.1mA ≤ IOUT ≤ 50mA 22 33 µF Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating ratings. Note 2: Human body model, 100pF discharge through a 1.5kΩ resistor. Note 3: The maximum power dissipation is a function of TJmax, θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJmax − TA)/θJA. If this dissipation is exceeded, the die temperature will rise above 150˚C and the LM9036 will go into thermal shutdown. Note 4: Typicals are at 25˚C (unless otherwise specified) and represent the most likely parametric norm. Note 5: Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level) and 100% tested. Note 6: To ensure constant junction temperature, pulse testing is used. Note 7: Worst case (Free Air) per EIA / JESD51-3. Note 8: Typical θJA with 1 square inch of 2oz copper pad area directly under the ground tab. Ordering Information TO-252 SOIC Mini SOIC 3.30V LM9036DT-3.3 LM9036M-3.3 LM9036MM-3.3 5.00V LM9036DT-3.3 LM9036M-5.0 LM9036MM-5.0 Typical Performance Characteristics Dropout Voltage Quiescent Current 20001108 www.national.com 20001111 4 Typical Performance Characteristics (Continued) Quiescent Current Quiescent Current 20001113 20001114 Peak Output Current 20001117 Using the θJA for a LM9036DT mounted on a circuit board as defined at (Note 8), and using the formula for maximum allowable dissipation given in (Note 3) for an ambient temperature (TA) of +85˚C, we find that PDMAX = 1.3W. Including the small contribution of the quiescent current IQ to the total power dissipation, the maximum input voltage (while still delivering 50mA output current) is 29.5V. The LM9036DT will go into thermal shutdown when attempting to deliver the full output current of 50mA, with an ambient temperature of +85˚C, and the input voltage is greater than 29.5V. Similarly, with an ambient temperature of 25˚C the PDMAX = 2.5W, and the LM9036DT can deliver the full output current of 50mA with an input voltage of up to 40V. While the LM9036 maintains regulation to 55V, it will not withstand a short circuit above 40V because of safe operating area limitations in the internal PNP pass device. Above 55V the LM9036 will break down with catastrophic effects on the regulator and possibly the load as well. Do not use this device in a design where the input operating voltage may exceed 40V, or where transients are likely to exceed 55V. Applications Information Unlike other PNP low dropout regulators, the LM9036 remains fully operational to 40V. Owing to power dissipation characteristics of the package, full output current cannot be guaranteed for all combinations of ambient temperature and input voltage. The junction to ambient thermal resistance θJA rating has two distinct components: the junction to case thermal resistance rating θJC; and the case to ambient thermal resistance rating θCA. The relationship is defined as: θJA = θJC + θCA. On the TO-252 package the ground tab is thermally connected to the backside of the die. Adding 1 square inch of 2 oz. copper pad area directly under the ground tab will improve the θJA rating to approximately 50˚C/W. While the LM9036 has an internally set thermal shutdown point of typically 150˚C, this is intended as a safety feature only. Continuous operation near the thermal shutdown temperature should be avoided as it may have a negative affect on the life of the device. 5 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted TO-252 Package (DT) NS Package Number TD03B 8 Lead Small Outline Molded Package (M) NS Package Number M08A www.national.com 6 LM9036 Ultra-Low Quiescent Current Voltage Regulator Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 8 Lead Mini SOIC (MM) NS Package Number MUA08A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.