HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Typical Applications Features The HMC641LC4 is ideal for: Broadband Performance: DC - 20 GHz • Telecom Infrastructure High Isolation: 42 dB @ 12 GHz • Microwave Radio & VSAT Low Insertion Loss: 2.1 dB @ 12 GHz • Military & Space Hybrids Integrated 2:4 TTL Decoder • Test Instrumentation 24 Lead 4x4mm SMT Package: 16mm² • SATCOM & Sensors General Description Functional Diagram The HMC641LC4 is a broadband non-reflective GaAs pHEMT SP4T switch in a compact 4x4 mm ceramic package. Covering DC to 20 GHz, this switch offers high isolation, low insertion loss and on-chip termination of isolated ports. This switch also includes an on board binary decoder circuit which reduces the number of required logic control lines from four to two. The HMC641LC4 is controlled with 0/ -5V logic, exhibits fast switching speed and consumes much less DC current than pin diode based solutions. The HMC641LC4 is also available in die form as the HMC641. Switches - SPDT - SMT 11 Electrical Specifications, TA = +25° C, With 0/-5V Control, Vss = -5V, 50 Ohm System Parameter Insertion Loss Isolation (RFC to RF1 - RF4) DC - 12 GHz DC - 20 GHz Return Loss “On State” Return Loss “Off State” Min. 30 30 DC - 12 GHz DC - 20 GHz DC - 20 GHz 10 20 Typ. Max. Units 1.6 2.3 2.8 3.5 dB dB 42 40 dB dB 18 17 dB dB 13 dB 15 23 dBm dBm Input Power for 1 dB Compression 0.05 - 0.25 GHz 0.25- 20 GHz Input Third Order Intercept (Two-Tone Input Power= +14 dBm Each Tone) 0.05 - 0.25 GHz 0.25 - 20 GHz 30 39 dBm dBm DC - 20 GHz 15 88 ns ns Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 11 - 1 Frequency DC - 12 GHz DC - 20 GHz For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Insertion Loss vs. Temperature Isolation 0 0 RF1 RF2 RF3 RF4 -20 ISOLATION (dB) INSERTION LOSS (dB) -10 -1 -2 +25 C +85 C -40 C -3 -30 -40 -50 -60 -4 -70 -5 -80 4 8 12 16 20 0 24 4 8 Return Loss 16 20 24 11 1 dB Input Compression Point 30 -5 INPUT COMPRESSION POINT (dBm) 0 RFC RF1,2,3,4 On RF1,2,3,4 Off -10 -15 -20 -25 -30 -35 25 20 15 10 0 4 8 12 16 20 24 0 2 4 6 8 FREQUENCY (GHz) 10 12 14 16 18 20 22 FREQUENCY (GHz) Input Third Order Intercept Point @ 0 dBm Tone Power 50 45 40 IP3 (dBm) RETURN LOSS (dB) 12 FREQUENCY (GHz) FREQUENCY (GHz) Switches - SPDT - SMT 0 35 30 25 20 15 0 5 10 15 20 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 11 - 2 HMC641LC4 v00.0609 Absolute Maximum Ratings Switches - SPDT - SMT 11 11 - 3 Bias Voltage (Vss) -7V Control Voltage Range (A & B) Vss -0.5V to +1V Maximum Input Power Channel Temperature Thermal Resistance Channel to die bottom (Insertion Loss Path) 199 °C/W Thermal Resistance Channel to die bottom (Terminated Path) 219 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1A GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Truth Table Control Input Signal Path State A B +24 dBm High High RF1 150 °C Low High RF2 High Low RF3 Low Low RF4 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RFC to: Bias Voltage & Current Vss Range= -5.0 Vdc ±10% Vss (Vdc) Iss (Typ) (mA) Iss (Max) (mA) -5 1.7 5.0 TTL/CMOS Control Voltages State Bias Condition Low -2.5V to 0V @ 30 µA Typ. High -5V to -3.8V @ 1.7 µA Typ. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA 2. LEAD AND GROUND PADDLE PLATING: 30-80 MICROINCHES GOLD OVER 50 MICROINCHES MINIMUM NICKEL. 3. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm DATUM -C6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. CLASSIFIED AS MOISTURE SENSITIVITY LEVEL (MSL) 1. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] Switches - SPDT - SMT 11 11 - 4 HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Pin Descriptions Pin Number Description 1, 5, 6, 13, 18 N/C These pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 2, 4, 7, 9, 10, 12, 17, 19, 21, 22, 24 Ground Paddle GND These pins and the exposed ground paddle must be connected to RF/DC ground. 3, 8, 11, 20, 23 RFC, RF1, RF2, RF3, RF4 These pads are DC coupled and matched to 50 Ohms. Blocking capacitors are required if RF line potential is not equal to 0V. 14 Vss Supply Voltage -5 Vdc ± 10%. 15 CTLB See Truth Table and Control Voltage Table. 16 CTLA See Truth Table and Control Voltage Table. Interface Schematic Switches - SPDT - SMT 11 Function 11 - 5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Evaluation PCB List of Materials for Evaluation PCB 126511 [1] Item Description J1 - J5 PCB Mount SMA Connector C1 1000 pF Capacitor, 0402 Pkg. U1 HMC641LC4 Switch PCB [2] 126508 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon FR4 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] Switches - SPDT - SMT 11 11 - 6