LCA210L Common Input, Dual-Pole OptoMOS® Relay INTEGRATED CIRCUITS DIVISION Parameter Blocking Voltage Load Current On-Resistance (max) Ratings 350 100 35 Units VP mArms / mADC Features • Current Limiting • 3750Vrms Input/Output Isolation • Low Drive Power Requirements (TTL/CMOS Compatible) • High Reliability • Arc-Free With No Snubbing Circuits • FCC Compatible • VDE Compatible • No EMI/RFI Generation • Small 8-Pin Package • Machine Insertable, Wave Solderable • Surface Mount Tape & Reel Version Available Description The LCA210L is a current-limiting, common input, dual normally open (2-Form-A) solid state relay that has two independent MOSFET switch outputs controlled by a common input signal. It employs optically coupled MOSFET technology to provide 3750Vrms of input to output isolation. Its optically coupled outputs, which use the patented OptoMOS architecture, are controlled by a highly efficient GaAIAs infrared LED. Common input OptoMOS relays can replace standard dual-pole relays in a variety of applications. The common-input relay eliminates the need to make an external circuit connection when both poles are controlled by a common signal. Approvals Applications • Telecommunications • Telecom Switching • Tip/Ring Circuits • Modem Switching (Laptop, Notebook, Pocket Size) • Hook Switch • Dial Pulsing • Ground Start • Ringing Injection • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment—Patient/Equipment Isolation • Security • Aerospace • Industrial Controls • UL Recognized Component: File E76270 • CSA Certified Component: Certificate 1175739 • EN/IEC 60950-1 Certified Component: TUV Certificate B 09 07 49410 004 Ordering Information Part # LCA210L LCA210LS LCA210LSTR Description 8-Pin DIP (50/Tube) 8-Pin Surface Mount (50/Tube) 8-Pin Surface Mount (1,000/Reel) Pin Configuration NC + Control - Control NC 1 8 2 7 3 6 4 5 Output 1 Output 1 Output 2 Output 2 Switching Characteristics of Normally Open Devices Form-A IF 90% 10% ILOAD Pb DS-LCA210L-R04 ton e3 www.ixysic.com toff 1 INTEGRATED CIRCUITS DIVISION LCA210L Absolute Maximum Ratings @ 25ºC Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 Derate linearly 1.33 mW / ºC 2 Derate linearly 6.67 mW / ºC Ratings 350 5 100 1 150 800 3750 -40 to +85 -40 to +125 Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Units VP V mA A mW mW Vrms °C °C Electrical Characteristics @ 25ºC Parameter Output Characteristics Load Current, Continuous Peak Load Current Load Current Limiting Conditions Symbol Min Typ Max Units 10ms Max IF=8mA IL ILPK ICL 130 170 85 170 210 On-Resistance 1 IL=85mA RON - - 35 mArms / mADC mAP mA Off-State Leakage Current VL=350VP ILEAK - - 1 µA ton - - 4 VL=50V, f=1MHz toff COUT - 25 4 - IL=120mA IF=8mA VR=5V IF IF VF IR 0.8 0.9 - 1.4 1.2 - 8 1.4 20 mA mA V µA - CI/O - 3 - pF Switching Speeds Turn-On Turn-Off Output Capacitance Input Characteristics 2 Input Control Current to Activate Input Control Current to Deactivate Input Voltage Drop Reverse Input Current Common Characteristics Capacitance, Input to Output 1 2 IF=8mA, VL=10V ms pF Measurement taken within 1 second of on-time. Input characteristics represent requirements of two parallel-connected LEDs. 2 www.ixysic.com R04 INTEGRATED CIRCUITS DIVISION LCA210L PERFORMANCE DATA @25ºC (Unless Otherwise Noted)* 25 20 15 10 5 1.17 25 1.19 1.21 1.23 15 10 5 20 15 10 5 0 0.6 1.25 0.7 0.8 .9 1.0 1.1 1.2 0.0 0.1 0.2 0.3 0.4 0.5 0.6 LED Forward Voltage Drop (V) Turn-On Time (ms) Turn-Off Time (ms) Typical IF for Switch Operation (N=50, IL=85mADC) Typical IF for Switch Dropout (N=50, IL=85mADC) Typical On-Resistance Distribution (N=50, IF=2mA, IL=120mADC) 25 20 Device Count (N) Device Count (N) 20 0 0 Typical Turn-Off Time (N=50, IF=8mA, IL=85mADC) 25 Device Count (N) Device Count (N) Device Count (N) 30 25 Typical Turn-On Time (N=50, IF=8mA, IL=85mADC) 15 10 5 0 30 20 15 10 5 1.30 1.82 2.34 2.86 3.38 25 20 15 10 5 0 0.78 35 Device Count (N) 35 Typical LED Forward Voltage Drop (N=50, IF=8mA) 0.78 3.9 1.30 LED Current (mA) 1.82 2.34 2.86 3.38 0 3.9 17.0 17.4 LED Current (mA) 17.8 18.2 18.6 19.0 19.4 On-Resistance (:) Typical Blocking Voltage Distribution (N=50) 35 Device Count (N) 30 25 20 15 10 5 0 420 425 430 435 440 445 450 Blocking Voltage (VP) Typical Turn-On Time vs. LED Forward Current (IL=50mADC) 1.6 1.4 IF=50mA IF=30mA IF=20mA IF=10mA 1.2 1.0 0.8 -40 -20 0 20 40 60 Temperature (ºC) 80 100 120 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 Typical Turn-Off Time vs. LED Forward Current (IL=50mADC) 0.7 0.6 Turn-Off Time (ms) 1.8 Turn-On Time (ms) LED Forward Voltage Drop (V) Typical LED Forward Voltage Drop vs. Temperature 0.5 0.4 0.3 0.2 0.1 0 5 10 15 20 25 30 35 40 45 LED Forward Current (mA) 50 55 5 10 15 20 25 30 35 40 45 50 55 LED Forward Current (mA) *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R04 www.ixysic.com 3 INTEGRATED CIRCUITS DIVISION LCA210L Typical Turn-On Time vs. Temperature (IL=40mADC) IF=8mA IF=16mA IF=32mA -40 6.0 -20 0 20 40 60 80 100 30 IF=16mA 20 0 -20 0 20 40 60 80 -40 100 0 20 40 60 80 100 Temperature (ºC) Typical IF for Switch Operation vs. Temperature (IL=50mADC) Typical IF for Switch Dropout vs. Temperature (IL=50mADC) Typical Load Current vs. Load Voltage (IF=8mA) 6.0 150 3.0 2.0 Load Current (mA) 5.0 4.0 4.0 3.0 2.0 1.0 0 -20 0 20 40 60 80 50 0 -50 -150 -40 100 100 -100 0 -20 0 20 40 60 80 100 -3 -1 0 1 2 3 Temperature (ºC) Load Voltage (V) Maximum Load Current vs. Temperature Typical Blocking Voltage vs. Temperature Typical Leakage vs. Temperature Measured across Pins 5&6 or 7&8 0.014 420 0.012 140 120 100 80 IF=16mA IF=8mA 60 40 415 410 405 20 400 0 395 0 20 40 60 80 100 Leakage (PA) 0.016 425 Blocking Voltage (VP) 430 160 -20 -2 Temperature (ºC) 180 -40 -20 Temperature (ºC) LED Current (mA) LED Current (mA) IF=8mA 40 Temperature (ºC) 1.0 Load Current (mA) 50 10 -40 5.0 -40 Typical On-Resistance vs. Temperature (IL=100mADC) 60 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 On-Resistance (:) 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 Typical Turn-Off Time vs. Temperature (IF=8mA, IL=40mADC) Turn-Off Time (ms) Turn-On Time (ms) PERFORMANCE DATA @25ºC (Unless Otherwise Noted)* 0.008 0.006 0.004 0.002 -40 120 -20 0 20 40 60 80 100 Temperature (ºC) Temperature (ºC) 0.010 0 -40 -20 0 20 40 60 80 100 Temperature (ºC) Load Current (A) Energy Rating Curve 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 10Ps 100Ps 1ms 10ms 100ms 1s 10s 100s Time *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.ixysic.com R04 INTEGRATED CIRCUITS DIVISION LCA210L Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Rating LCA210L / LCA210LS MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020 must be observed. Device Maximum Temperature x Time LCA210L / LCA210LS 250ºC for 30 seconds Board Wash IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb R04 e3 www.ixysic.com 5 INTEGRATED CIRCUITS DIVISION LCA210L MECHANICAL DIMENSIONS LCA210L 2.540 ± 0.127 (0.100 ± 0.005) 9.652 ± 0.381 (0.380 ± 0.015) 8-0.800 DIA. (8-0.031 DIA.) 2.540 ± 0.127 (0.100 ± 0.005) 9.144 ± 0.508 (0.360 ± 0.020) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 PCB Hole Pattern 7.620 ± 0.254 (0.300 ± 0.010) 6.350 ± 0.127 (0.250 ± 0.005) 0.457 ± 0.076 (0.018 ± 0.003) 3.302 ± 0.051 (0.130 ± 0.002) 7.620 ± 0.127 (0.300 ± 0.005) 7.239 TYP. (0.285) 4.064 TYP (0.160) 0.254 ± 0.0127 (0.010 ± 0.0005) 7.620 ± 0.127 (0.300 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) LCA210LS 9.652 ± 0.381 (0.380 ± 0.015) 2.540 ± 0.127 (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 0.635 ± 0.127 (0.025 ± 0.005) 3.302 ± 0.051 (0.130 ± 0.002) 9.525 ± 0.254 (0.375 ± 0.010) 0.457 ± 0.076 (0.018 ± 0.003) PCB Land Pattern 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 ± 0.254 (0.300 ± 0.010) 0.254 ± 0.0127 (0.010 ± 0.0005) 0.65 (0.0255) 4.445 ± 0.127 (0.175 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) 6 www.ixysic.com R04 INTEGRATED CIRCUITS DIVISION LCA210L LCA210LSTR Tape & Reel 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) K0 =4.90 (0.193) K1 =4.20 (0.165) Embossed Carrier Embossment W=16.00 (0.63) Bo=10.30 (0.406) Ao=10.30 (0.406) P=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2 For additional information please visit our website at: www.ixysic.com IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice. 7 Specification: DS-LCA210L-R04 ©Copyright 2012, IXYS Integrated Circuits Division OptoMOS® is a registered trademark of IXYS Integrated Circuits Division All rights reserved. Printed in USA. 12/22/2012