Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-Isolated DC-DC Power Modules 3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A Output Current Features RoHS Compliant Applications Compliant to RoHS EU Directive 2002/95/EC (Z versions) Compatible in a Pb-free or SnPb reflow environment (Z versions) DOSA based Wide Input voltage range (3Vdc-14.4Vdc) Output voltage programmable from 0.6Vdc to 5.5Vdc via external resistor. Digitally adjustable down to 0.45Vdc Digital interface through the PMBusTM # protocol Tunable LoopTM to op timize dynamic output voltage response Flexible output voltage sequencing EZSEQUENCE Distributed power architectures Intermediate bus voltage applications Power Good signal Telecommunications equipment Servers and storage applications Fixed switching frequency with capability of external synchronization Networking equipment Output overcurrent protection (non-latching) Industrial equipment Overtemperature protection Remote On/Off Ability to sink and source current Cost efficient open frame design Small size: 12.2 mm x 12.2 mm x 7.25 mm (0.48 in x 0.48 in x 0.29 in) Wide operating temperature range [-40°C to 85°C] UL* 60950-1Recognized, CSA C22.2 No. ‡ 60950-1-03 Certified, and VDE 0805:2001-12 (EN60950-1) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Vin+ VIN PGOOD Vout+ VOUT VS+ RTUNE MODULE SEQ Cin ON/OFF GND CTUNE CLK TRIM DATA ADDR0 SMBALRT# ADDR1 Co RTrim RADDR1 RADDR0 SIG_GND SYNC GND VS- † Description The 6A Digital Pico DLynxTM power modules are non-isolated dc-dc converters that deliver up to 6A of output current. These modules operate over a wide range of input voltage (VIN = 3Vdc-14.4Vdc) and provide a precisely regulated output voltage from 0.45Vdc to 5.5Vdc, programmable via an external resistor and further adjustable through PMBus. Features include a digital interface using the PMBus protocol, remote On/Off, adjustable output voltage, over current and overtemperature protection. The PMBus interface supports a range of commands to control and monitor the module. The Tunable LoopTM feature allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards ‡ # The PMBus name and logo are registered trademarks of the System Management Interface Forum (SMIF) Document No: DS11-008 ver. 0.33 PDF name: PDT006A0X.pdf Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit All VIN -0.3 15 V Input Voltage Continuous SEQ, SYNC, VS+ All 7 V CLK, DATA, SMBALERT All 3.6 V Operating Ambient Temperature All TA -40 85 °C All Tstg -55 125 °C (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit 3 14.4 Vdc 5 Adc Operating Input Voltage All VIN Maximum Input Current All IIN,max VO,set = 0.6 Vdc IIN,No load 30 mA (VIN=3V to 14V, IO=IO, max ) Input No Load Current (VIN = 12Vdc, IO = 0, module enabled) VO,set = 5Vdc IIN,No load 90 mA Input Stand-by Current (VIN = 12Vdc, module disabled) All IIN,stand-by 6 mA Inrush Transient All It Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1ȝH source impedance; VIN =0 to 14V, IO= IOmax ; See Test Configurations) All 11.2 mAp-p Input Ripple Rejection (120Hz) All -55 dB LINEAGE POWER 2 1 2 As 2 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Electrical Specifications (continued) Parameter Device Symbol Min Output Voltage Set-point (with 0.1% tolerance for external resistor used to set output voltage) All VO, set -1.0 Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) All VO, set -3.0 Adjustment Range (selected by an external resistor) (Some output voltages may not be possible depending on the input voltage – see Feature Descriptions Section) All VO 0.6 PMBus Adjustable Output Voltage Range All VO,adj -25 PMBus Output Voltage Adjustment Step Size All Remote Sense Range All Typ 0 Max Unit +1.0 % VO, set +3.0 % VO, set 5.5 Vdc +25 %VO,set 0.4 %VO,set 0.5 Vdc Output Regulation (for VO 2.5Vdc) Line (VIN=VIN, min to VIN, max) All +0.4 % VO, set Load (IO=IO, min to IO, max) All 10 mV Output Regulation (for VO < 2.5Vdc) Line (VIN=VIN, min to VIN, max) All 5 mV Load (IO=IO, min to IO, max) All 10 mV Temperature (Tref=TA, min to TA, max) All 0.4 % VO, set Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Co = 0.1ȝF // 22 ȝF ceramic capacitors) Peak-to-Peak (5Hz to 20MHz bandwidth) RMS (5Hz to 20MHz bandwidth) External Capacitance All All 50 100 mVpk-pk 20 38 mVrms 1 TM Without the Tunable Loop All CO, max 22 47 ȝF ESR 0.15 mȍ All CO, max 22 1000 ȝF ESR 10 mȍ All CO, max 22 3000 ȝF Output Current (in either sink or source mode) All Io 0 6 Adc Output Current Limit Inception (Hiccup Mode) (current limit does not operate in sink mode) All IO, lim 200 % Io,max Output Short-Circuit Current All IO, s/c 367 mArms ESR 1 mȍ With the Tunable Loop TM (VO250mV) ( Hiccup Mode ) Efficiency VIN= 12Vdc, TA=25°C IO=IO, max , VO= VO,set Switching Frequency 1 VO,set = 0.6Vdc Ș 75.6 % VO, set = 1.2Vdc Ș 85.0 % VO,set = 1.8Vdc Ș 88.6 % VO,set = 2.5Vdc Ș 90.6 % VO,set = 3.3Vdc Ș 92.1 % VO,set = 5.0Vdc Ș 93.8 % All fsw 600 kHz TM External capacitors may require using the new Tunable Loop feature to ensure that the module is stable as well as TM getting the best transient response. See the Tunable Loop section for details. LINEAGE POWER 3 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Electrical Specifications (continued) Parameter Device Frequency Synchronization Symbol Min Typ Max Unit 720 kHz All Synchronization Frequency Range All High-Level Input Voltage All 510 VIH 2.0 V Low-Level Input Voltage All VIL 0.4 V Input Current, SYNC All ISYNC 100 nA Minimum Pulse Width, SYNC All tSYNC 100 ns Maximum SYNC rise time All tSYNC_SH 100 ns General Specifications Parameter Calculated MTBF (IO=0.8IO, max, TA=40°C) Telecordia Issue 2 Method 1 Case 3 Device Min All Typ 18,595,797 Weight Max Hours TBD Unit g (oz.) Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Input High Current All IIH Input High Voltage All VIH Min Typ Max Unit 1 mA VIN,max V On/Off Signal Interface (VIN=VIN, min to VIN, max ; open collector or equivalent, Signal referenced to GND) Device code with suffix “4” – Positive Logic (See Ordering Information) Logic High (Module ON) 2 Logic Low (Module OFF) Input Low Current All IIL 1 mA Input Low Voltage All VIL -0.2 0.6 V Device Code with no suffix – Negative Logic (See Ordering Information) (On/OFF pin is open collector/drain logic input with external pull-up resistor; signal referenced to GND) Logic High (Module OFF) Input High Current All IIH ʊ ʊ 1 mA Input High Voltage All VIH 2.0 ʊ VIN, max Vdc Logic Low (Module ON) Input low Current All IIL ʊ ʊ 10 ȝA Input Low Voltage All VIL -0.2 ʊ 0.6 Vdc LINEAGE POWER 4 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Feature Specifications (cont.) Parameter Device Symbol Min Typ Max Units Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo = 10% of Vo, set) All Tdelay ʊ 0.4 ʊ msec Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which Von/Off is enabled until Vo = 10% of Vo, set) All Tdelay ʊ 0.8 ʊ msec Output voltage Rise time (time for Vo to rise from 10% of Vo, set to 90% of Vo, set) All Trise ʊ 2.2 ʊ msec 3.0 % VO, set Turn-On Delay and Rise Times (VIN=VIN, nom, IO=IO, max , VO to within ±1% of steady state) o Output voltage overshoot (TA = 25 C VIN= VIN, min to VIN, max,IO = IO, min to IO, max) With or without maximum external capacitance Over Temperature Protection (See Thermal Considerations section) All PMBus Over Temperature Warning Threshold Tracking Accuracy (Power-Up: 2V/ms) (Power-Down: 2V/ms) Tref TBD All TWARN 130 All VSEQ –Vo 100 mV All VSEQ –Vo 100 mV °C °C (VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo) Input Undervoltage Lockout Turn-on Threshold All 2.79 Vdc Turn-off Threshold All 2.58 Vdc Hysteresis All 0.2 Vdc PMBus Adjustable Input Under Voltage Lockout Thresholds All Resolution of Adjustable Input Under Voltage Threshold All 2.5 14 Vdc 500 mV PGOOD (Power Good) Signal Interface Open Drain, Vsupply ≤ 5VDC Overvoltage threshold for PGOOD ON All 108 %VO, set Overvoltage threshold for PGOOD OFF All 105 %VO, set Undervoltage threshold for PGOOD ON All 110 %VO, set Undervoltage threshold for PGOOD OFF All 90 %VO, set Pulldown resistance of PGOOD pin All 50 Ω Sink current capability into PGOOD pin All 5 mA LINEAGE POWER 5 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Digital Interface Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Conditions Symbol Min Input High Voltage (CLK, DATA) VIH 2.1 Input Low Voltage (CLK, DATA) VIL Input high level current (CLK, DATA) IIH -10 IIL -10 Typ Max Unit 3.6 V PMBus Signal Interface Characteristics Input low level current (CLK, DATA) 0.8 V 10 ʅA 10 ʅA 0.4 V 10 ʅA 400 kHz Output Low Voltage (CLK, DATA, SMBALERT#) IOUT=2mA VOL Output high level open drain leakage current (DATA, SMBALERT#) VOUT=3.6V IOH Slave Mode FPMB 10 Receive Mode Transmit Mode tHD:DAT 0 300 ns tSU:DAT 250 ns Read delay time tDLY 153 Output current measurement range IRNG 0 Output current measurement resolution IRES 62.5 Output current measurement gain accuracy IACC Pin capacitance PMBus Operating frequency range Data hold time Data setup time 0 CO 0.7 pF Measurement System Characteristics Output current measurement offset 192 231 ȝs 18 A mA ±5 IOFST % 0.1 A 5.5 V VOUT measurement range VOUT(rng) VOUT measurement resolution VOUT(res) VOUT measurement gain accuracy VOUT(gain) -2 2 LSB VOUT measurement offset VOUT(ofst) -3 3 LSB VIN measurement range VIN(rng) 0 14.4 VIN measurement resolution VIN(res) VIN measurement gain accuracy VIN(gain) -2 2 LSB VIN measurement offset VIN(ofst) -5.5 1.4 LSB LINEAGE POWER 0 16.25 mV 32.5 V mV 6 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Characteristic Curves The following figures provide typical characteristics for the 6A Digital Pico DLynxTM at 0.6Vo and 25oC. 85 6.0 OUTPUT CURRENT, Io (A) EFFICIENCY, η (%) 80 Vin=3.3V 75 70 65 Vin=14V Vin=12V 60 55 50 0 1 2 3 4 5 NC 100 300 200 Ruggedized (D) Part (105 C) 80 85 400 2.0 1.0 90 95 100 105 OUTPUT VOLTAGE VO (V) (5mV/div) IO (A) (2Adiv) TIME, t (20µs /div) INPUT VOLTAGE VIN (V) (5V/div) VO (V) (200mV/div) Figure 4. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout=1x47uF + 4x330uF, CTune=33nF, RTune=178 OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (200mV/div) 3.0 Figure 2. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT CURRENT, VO (V) (10mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE LINEAGE POWER 2m/s (400LFM) 400 O TIME, t (1µs/div) TIME, t (2ms/div) 200 300 4.0 Standard Part (85 C) AMBIENT TEMPERATURE, TA C Figure 1. Converter Efficiency versus Output Current. Figure 5. Typical Start-up Using On/Off Voltage (Io = Io,max). NC 100 75 6 OUTPUT CURRENT, IO (A) Figure 3. Typical output ripple and noise (CO=22ʅF ceramic, VIN = 12V, Io = Io,max, ). NC 5.0 TIME, t (2ms/div) Figure 6. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 7 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Characteristic Curves The following figures provide typical characteristics for the 6A Digital Pico DLynxTM at 1.2Vo and 25oC. 95 6.0 90 80 OUTPUT CURRENT, Io (A) EFFICIENCY, η (%) 85 Vin=3.3V 75 Vin=14V 70 Vin=12V 65 60 55 50 0 1 2 3 4 5 6 200 400 3.0 NC 100 200 300 2.0 400 2m/s (400LFM) Standard Part (85 C) Ruggedized (D) Part (105 C) 1.0 80 85 90 95 100 105 OUTPUT VOLTAGE VO (V) (10mV/div) IO (A) (2Adiv) TIME, t (20µs /div) INPUT VOLTAGE VIN (V) (5V/div) VO (V) (500mV/div) Figure 10. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout=1x47uF + 2x330uF, CTune=12nF, RTune=178 OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (500mV/div) 300 Figure 8. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT CURRENT, VO (V) (20mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE LINEAGE POWER 100 O TIME, t (1µs/div) Figure 1. Typical Start-up Using On/Off Voltage (Io = Io,max). 4.0 NC AMBIENT TEMPERATURE, TA C Figure 7. Converter Efficiency versus Output Current. TIME, t (2ms/div) NC 75 OUTPUT CURRENT, IO (A) Figure 9. Typical output ripple and noise (CO=22ʅF ceramic, VIN = 12V, Io = Io,max, ). 5.0 TIME, t (2ms/div) Figure 12. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 8 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Characteristic Curves The following figures provide typical characteristics for the 6A Digital Pico DLynxTM at 1.8Vo and 25oC. 95 6.0 OUTPUT CURRENT, Io (A) EFFICIENCY, η (%) 90 Vin=3.3V 85 Vin=14V 80 Vin=12V 75 70 0 1 2 3 4 5 200 400 3.0 NC 100 200 300 2.0 400 2m/s (400LFM) Standard Part (85 C) Ruggedized (D) Part (105 C) 1.0 80 85 90 95 100 105 OUTPUT VOLTAGE VO (V) (20mV/div) IO (A) (2Adiv) TIME, t (20µs /div) INPUT VOLTAGE VIN (V) (5V/div) VO (V) (500mV/div) Figure 16. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout= 1x47uF + 1x330uF, CTune=4700pF, RTune=178 OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (500mV/div) 300 Figure 14. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT CURRENT, VO (V) (20mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE LINEAGE POWER 100 O TIME, t (1µs/div) TIME, t (2ms/div) 4.0 NC AMBIENT TEMPERATURE, TA C Figure 13. Converter Efficiency versus Output Current. Figure 17. Typical Start-up Using On/Off Voltage (Io = Io,max). NC 75 6 OUTPUT CURRENT, IO (A) Figure 15. Typical output ripple and noise (CO=22ʅF ceramic, VIN = 12V, Io = Io,max, ). 5.0 TIME, t (2ms/div) Figure 18. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 9 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Characteristic Curves The following figures provide typical characteristics for the 6A Digital Pico DLynxTM at 2.5Vo and 25oC. 95 EFFICIENCY, η (%) OUTPUT CURRENT, Io (A) 6.0 90 Vin=4.5V 85 Vin=14V Vin=12V 80 75 70 0 1 2 3 4 5 NC 300 2.0 2m/s (400LFM) 100 200 400 Ruggedized (D) Part (105 C) 1.0 80 85 90 95 100 105 OUTPUT VOLTAGE VO (V) (20mV/div) IO (A) (2Adiv) TIME, t (20µs /div) INPUT VOLTAGE VIN (V) (5V/div) VO (V) (1V/div) Figure 22. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout = 3x47uF, CTune=3300pF, RTune=178 OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (1V/div) 3.0 NC Figure 20. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT CURRENT, VO (V) (20mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE LINEAGE POWER 4.0 Standard Part (85 C) O TIME, t (1µs/div) TIME, t (2ms/div) 200 400 AMBIENT TEMPERATURE, TA C Figure 19. Converter Efficiency versus Output Current. Figure 23. Typical Start-up Using On/Off Voltage (Io = Io,max). 100 300 75 6 OUTPUT CURRENT, IO (A) Figure 21. Typical output ripple and noise (CO=22ʅF ceramic, VIN = 12V, Io = Io,max, ). NC 5.0 TIME, t (2ms/div) Figure 24. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 10 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Characteristic Curves The following figures provide typical characteristics for the 6A Digital Pico DLynxTM at 3.3Vo and 25oC. 100 6.0 90 OUTPUT CURRENT, Io (A) EFFICIENCY, η (%) 95 Vin=4.5V 85 Vin=14V Vin=12V 80 75 70 0 1 2 3 4 5 3.0 100 NC 300 2.0 200 Ruggedized (D) Part (105 C) 400 1.0 80 85 90 95 100 105 VO (V) (20mV/div) OUTPUT VOLTAGE TIME, t (20µs /div) INPUT VOLTAGE VIN (V) (5V/div) VO (V) (1V/div) Figure 28 Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout= 3x47uF, CTune=3300pF, RTune=178 OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (1V/div) 2m/s (400LFM) IO (A) (2Adiv) OUTPUT CURRENT, VO (V) (20mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE LINEAGE POWER 400 4.0 Figure 26. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (1µs/div) TIME, t (2ms/div) NC Standard Part (85 C) AMBIENT TEMPERATURE, TA C Figure 25. Converter Efficiency versus Output Current. Figure 29. Typical Start-up Using On/Off Voltage (Io = Io,max). 200 O OUTPUT CURRENT, IO (A) Figure 27. Typical output ripple and noise (CO=22ʅF ceramic, VIN = 12V, Io = Io,max, ). 300 75 6 100 NC 5.0 TIME, t (2ms/div) Figure 30. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 11 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Characteristic Curves The following figures provide typical characteristics for the 6A Digital Pico DLynxTM at 5Vo and 25oC. 100 6.0 OUTPUT CURRENT, Io (A) EFFICIENCY, η (%) 95 90 Vin=7V 85 Vin=14V Vin=12V 80 75 70 0 1 2 3 4 5 Ruggedized (D) Part (105 C) 400 1.0 80 85 90 95 100 105 OUTPUT VOLTAGE VO (V) (50mV/div) TIME, t (20µs /div) INPUT VOLTAGE VIN (V) (5V/div) VO (V) (2V/div) Figure 34. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout= 2x47uF, CTune=2200pF, RTune=261 OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (2V/div) 2.0 100 200 IO (A) (2Adiv) OUTPUT CURRENT, VO (V) (50mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE LINEAGE POWER NC 300 Figure 32. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (1µs/div) Figure 35. Typical Start-up Using On/Off Voltage (Io = Io,max). 0.5m/s (100LFM) 3.0 AMBIENT TEMPERATURE, TA C Figure 31. Converter Efficiency versus Output Current. TIME, t (2ms/div) 400 4.0 Standard Part (85 C) O OUTPUT CURRENT, IO (A) Figure 33. Typical output ripple and noise (CO=22ʅF ceramic, VIN = 12V, Io = Io,max, ). NC 200 300 75 6 100 NC 5.0 TIME, t (2ms/div) Figure 36. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 12 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Design Considerations Input Filtering The 6A Digital Pico DLynxTM module should be connected to a low ac-impedance source. A highly inductive source can affect the stability of the module. An input capacitance must be placed directly adjacent to the input pin of the module, to minimize input ripple voltage and ensure module stability. To minimize input voltage ripple, ceramic capacitors are recommended at the input of the module. Figure 37 shows the input ripple voltage for various output voltages at 6A of load current with 1x22 µF or 2x22 µF ceramic capacitors and an input of 12V. 190 180 170 160 150 140 130 120 110 100 90 80 70 1x22uF Ripple (mVp-p) 2x22uF TM achieved by using the Tunable Loop later in this data sheet. 40 feature described 1x22uF Ext Cap 1x47uF Ext Cap Ripple (mVp-p) Preliminary Data Sheet October 17, 2011 30 2x47uF Ext Cap 20 10 0 0.5 1 1.5 2 2.5 3 3.5 4 Output Voltage(Volts) 4.5 5 Figure 38. Output ripple voltage for various output voltages with external 1x22 µF, 1x47 µF, or 2x47 µF ceramic capacitors at the output (6A load). Input voltage is 12V. Safety Considerations 0.5 1.5 2.5 3.5 4.5 Output Voltage(Volts) Figure 37. Input ripple voltage for various output voltages with 1x22 µF or 2x22 µF ceramic capacitors at the input (6A load). Input voltage is 12V. Output Filtering These modules are designed for low output ripple voltage and will meet the maximum output ripple specification with 0.1 µF ceramic and 22 µF ceramic capacitors at the output of the module. However, additional output filtering may be required by the system designer for a number of reasons. First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. For safety agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., UL 60950-1 2nd, CSA C22.2 No. 60950-1-07, DIN EN 60950-1:2006 + A11 (VDE0805 Teil 1 + A11):200911; EN 60950-1:2006 + A11:2009-03. For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. The input to these units is to be provided with a fuse with a maximum rating of TBD in the positive input lead. To reduce the output ripple and improve the dynamic response to a step load change, additional capacitance at the output can be used. Low ESR polymer and ceramic capacitors are recommended to improve the dynamic response of the module. Figure 38 provides output ripple information for different external capacitance values at various Vo and a full load current of 6A. For stable operation of the module, limit the capacitance to less than the maximum output capacitance as specified in the electrical specification table. Optimal performance of the module can be LINEAGE POWER 13 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Analog Feature Descriptions Remote On/Off DLYNX MODULE +3.3V +VIN The module can be turned ON and OFF either by using the ON/OFF pin (Analog interface) or through the PMBus interface (Digital). The module can be configured in a number of ways through the PMBus interface to react to the two ON/OFF inputs: Rpullup I Q1 Q2 22K V ON/OFF _ GND Figure 39. Circuit configuration for using positive On/Off logic. DLYNX MODULE +3.3V +VIN Rpullup I Analog On/Off The 6A Digital Pico DLynxTM power modules feature an On/Off pin for remote On/Off operation. Two On/Off logic options are available. In the Positive Logic On/Off option, (device code suffix “4” – see Ordering Information), the module turns ON during a logic High on the On/Off pin and turns OFF during a logic Low. With the Negative Logic On/Off option, (no device code suffix, see Ordering Information), the module turns OFF during logic High and ON during logic Low. The On/Off signal should be always referenced to ground. For either On/Off logic option, leaving the On/Off pin disconnected will turn the module ON when input voltage is present. ENABLE 22K ON/OFF + • Module ON/OFF can be controlled only through the analog interface (digital interface ON/OFF commands are ignored) • Module ON/OFF can be controlled only through the PMBus interface (analog interface is ignored) • Module ON/OFF can be controlled by either the analog or digital interface The default state of the module (as shipped from the factory) is to be controlled by the analog interface only. If the digital interface is to be enabled, or the module is to be controlled only through the digital interface, this change must be made through the PMBus. These changes can be made and written to non-volatile memory on the module so that it is remembered for subsequent use. 10K 10K ON/OFF ENABLE 22K Q1 + Q2 V ON/OFF _ 22K GND Figure 40. Circuit configuration for using negative On/Off logic. Monotonic Start-up and Shutdown For positive logic modules, the circuit configuration for using the On/Off pin is shown in Figure 39. When the external transistor Q2 is in the OFF state, the internal transistor Q1 is turned ON, and the internal PWM #Enable signal is pulled low causing the module to be ON. When transistor Q2 is turned ON, the On/Off pin is pulled low and the module is OFF. A suggested value for Rpullup is 20kΩ. The module has monotonic start-up and shutdown behavior for any combination of rated input voltage, output current and operating temperature range. For negative logic On/Off modules, the circuit configuration is shown in Fig. 40. The On/Off pin should be pulled high with an external pull-up resistor (suggested value for the 3V to 14V input range is 20Kohms). When transistor Q2 is in the OFF state, the On/Off pin is pulled high, transistor Q1 is turned ON and the module is OFF. To turn the module ON, Q2 is turned ON pulling the On/Off pin low, turning transistor Q1 OFF resulting in the PWM Enable pin going high. Analog Output Voltage Programming Digital On/Off Please see the Digital Feature Descriptions section. LINEAGE POWER Startup into Pre-biased Output The module can start into a prebiased output as long as the prebias voltage is 0.5V less than the set output voltage. The output voltage of the module is programmable to any voltage from 0.6dc to 5.5Vdc by connecting a resistor between the Trim and SIG_GND pins of the module. Certain restrictions apply on the output voltage set point depending on the input voltage. These are shown in the Output Voltage vs. Input Voltage Set Point Area plot in Fig. 41. The Upper Limit curve shows that for output voltages lower than 1V, the input voltage must be lower than the maximum of 14.4V. The Lower Limit curve shows that for output voltages higher than 0.6V, the input voltage needs to be larger than the minimum of 3V. 14 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 VO, set (V) 0.6 0.9 1.0 1.2 1.5 1.8 2.5 3.3 5.0 16 Input Voltage (v) 14 12 Upper 10 8 6 4 Lower 2 Rtrim (Kȍ) Open 40 30 20 13.33 10 6.316 4.444 2.727 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 Digital Output Voltage Adjustment Output Voltage (V) Figure 41. Output Voltage vs. Input Voltage Set Point Area plot showing limits where the output voltage can be set for different input voltages. VIN(+) VO(+) Please see the Digital Feature Descriptions section. Remote Sense The power module has a Remote Sense feature to minimize the effects of distribution losses by regulating the voltage between the sense pins (VS+ and VS-). The voltage drop between the sense pins and the VOUT and GND pins of the module should not exceed 0.5V. Analog Voltage Margining VS+ ON/OFF LOAD TRIM Rtrim SIG_GND VSņ Caution – Do not connect SIG_GND to GND elsewhere in the layout Figure 42. Circuit configuration for programming output voltage using an external resistor. Output voltage margining can be implemented in the module by connecting a resistor, Rmargin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to output pin for margining-down. Figure 43 shows the circuit configuration for output voltage margining. The POL Programming Tool, available at www.lineagepower.com under the Downloads section, also calculates the values of Rmargin-up and Rmargin-down for a specific output voltage and % margin. Please consult your local Lineage Power technical representative for additional details. Vo Rmargin-down Without an external resistor between Trim and SIG_GND pins, the output of the module will be 0.6Vdc.To calculate the value of the trim resistor, Rtrim for a desired output voltage, should be as per the following equation: MODULE Q2 Trim Rmargin-up ª 12 º Rtrim = « » kΩ ¬ (Vo − 0.6) ¼ Rtrim is the external resistor in kȍ Vo is the desired output voltage. Table 1 provides Rtrim values required for some common output voltages. Rtrim Q1 SIG_GND Figure 43. Circuit Configuration for margining Output voltage. Digital Output Voltage Margining Please see the Digital Feature Descriptions section. Table 1 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Output Voltage Sequencing The power module includes a sequencing feature, EZSEQUENCE that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When not using the sequencing feature, leave it unconnected. The voltage applied to the SEQ pin should be scaled down by the same ratio as used to scale the output voltage down to the reference voltage of the module. This is accomplished by an external resistive divider connected across the sequencing voltage before it is fed to the SEQ pin as shown in Fig. 44. In addition, a small capacitor (suggested value 100pF) should be connected across the lower resistor R1. For all DLynx modules, the minimum recommended delay between the ON/OFF signal and the sequencing signal is 10ms to ensure that the module output is ramped up according to the sequencing signal. This ensures that the module soft-start routine is completed before the sequencing signal is allowed to ramp up. DLynx Module fault (see the description of the PMBus command VOUT_UV_FAULT_RESPONSE for additional information). Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. Digital Adjustable Overcurrent Warning Please see the Digital Feature Descriptions section. Overtemperature Protection To provide protection in a fault condition, the unit is equipped with a thermal shutdown circuit. The unit will shut down if the overtemperature threshold of o 150 C(typ) is exceeded at the thermal reference point Tref .Once the unit goes into thermal shutdown it will then wait to cool before attempting to restart. Digital Temperature Status via PMBus Please see the Digital Feature Descriptions section. V SEQ Digitally Adjustable Output Over and Under Voltage Protection 20K Please see the Digital Feature Descriptions section. SEQ Input Undervoltage Lockout R1=Rtrim 100 pF SIG_GND Figure 44. Circuit showing connection of the sequencing signal to the SEQ pin. When the scaled down sequencing voltage is applied to the SEQ pin, the output voltage tracks this voltage until the output reaches the set-point voltage. The final value of the sequencing voltage must be set higher than the set-point voltage of the module. The output voltage follows the sequencing voltage on a one-to-one basis. By connecting multiple modules together, multiple modules can track their output voltages to the voltage applied on the SEQ pin. To initiate simultaneous shutdown of the modules, the SEQ pin voltage is lowered in a controlled manner. The output voltage of the modules tracks the voltages below their set-point voltages on a one-to-one basis. A valid input voltage must be maintained until the tracking and output voltages reach ground potential. At input voltages below the input undervoltage lockout limit, the module operation is disabled. The module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. Digitally Adjustable Input Undervoltage Lockout Please see the Digital Feature Descriptions section. Digitally Adjustable Power Good Thresholds Please see the Digital Feature Descriptions section. Note that in all digital DLynx series of modules, the PMBus Output Undervoltage Fault will be tripped when sequencing is employed. This will be detected using the STATUS_WORD and STATUS_VOUT PMBus commands. In addition, the SMBALERT# signal will be asserted low as occurs for all faults and warnings. To avoid the module shutting down due to the Output Undervoltage Fault, the module must be set to continue operation without interruption as the response to this LINEAGE POWER 16 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Synchronization The module switching frequency can be synchronized to a signal with an external frequency within a specified range. Synchronization can be done by using the external signal applied to the SYNC pin of the module as shown in Fig. 45, with the converter being synchronized by the rising edge of the external signal. The Electrical Specifications table specifies the requirements of the external SYNC signal. If the SYNC pin is not used, the module should free run at the default switching frequency. If synchronization is not being used, connect the SYNC pin to GND. MODULE SYNC + ņ External capacitors are usually added to the output of the module for two reasons: to reduce output ripple and noise (see Figure 38) and to reduce output voltage deviations from the steady-state value in the presence of dynamic load current changes. Adding external capacitance however affects the voltage control loop of the module, typically causing the loop to slow down with sluggish response. Larger values of external capacitance could also cause the module to become unstable. TM The Tunable Loop allows the user to externally adjust the voltage control loop to match the filter network connected to the output of the module. The Tunable LoopTM is implemented by connecting a series R-C between the VS+ and TRIM pins of the module, as shown in Fig. 47. This R-C allows the user to externally adjust the voltage loop feedback compensation of the module. VOUT VS+ GND Figure 45. External source connections to synchronize switching frequency of the module. Measuring Output Current, Output Voltage and Input Voltage RTune MODULE TRIM Please see the Digital Feature Descriptions section. Dual Layout Identical dimensions and pin layout of Analog and Digital Pico DLynx modules permit migration from one to the other without needing to change the layout. To support this, 2 separate Trim Resistor locations have to be provided in the layout. As shown in Fig. 46, for the digital modules, the resistor is connected between the TRIM pad and SGND and in the case of the analog module it is connected between TRIM and GND. MODULE TRIM (PVX006 / PDT006) Rtrim1 for Digital Rtrim2 for Analog SIG_GND GND(Pin 7) Caution – For digital modules, do not connect SIG_GND to GND elsewhere in the layout Figure 46. Connections to support either Analog or Digital PicoDLynx on the same layout. Tunable LoopTM The module has a feature that optimizes transient response of the module called Tunable LoopTM. CO CTune RTrim SIG_GND GND Figure. 47. Circuit diagram showing connection of RTUME and CTUNE to tune the control loop of the module. Recommended values of RTUNE and CTUNE for different output capacitor combinations are given in Tables 2 and 3. Table 3 shows the recommended values of RTUNE and CTUNE for different values of ceramic output capacitors up to 1000uF that might be needed for an application to meet output ripple and noise requirements. Selecting RTUNE and CTUNE according to Table 3 will ensure stable operation of the module. In applications with tight output voltage limits in the presence of dynamic current loading, additional output capacitance will be required. Table 3 lists recommended values of RTUNE and CTUNE in order to meet 2% output voltage deviation limits for some common output voltages in the presence of a 6A to 6A step change (50% of full load), with an input voltage of 12V. Please contact your Lineage Power technical representative to obtain more details of this feature as well as for guidelines on how to select the right value of external R-C to tune the module for best transient performance and stable operation for other output capacitance values. 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Table 2. General recommended values of of RTUNE and CTUNE for Vin=12V and various external ceramic capacitor combinations. Co 1x47µF 2x47µF 4x47µF 6x47µF 10x47µF RTUNE 330 CTUNE 680pF 270 220 180 180 1800pF 3300pF 4700pF 5600pF Table 3. Recommended values of RTUNE and CTUNE to obtain transient deviation of 2% of Vout for a 3A step load with Vin=12V. Vo Co 5V 3.3V 2.5V 1.8V 0.6V 2x47µF 3x47µF 3x47µF 1x330µF 2x330µF 4x330µF Polymer Polymer Polymer RTUNE 270 180 180 180 CTUNE 2200pF 3300pF 3300pF 4700pF ∆V 1.2V 76mV 48mV 47mV 33mV 180 180 12nF 33nF 18mV 10mV Note: The capacitors used in the Tunable Loop tables are 47 ȝF/3 m ESR ceramic and 330 ȝF/12 m ESR polymer capacitors. LINEAGE POWER 18 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Digital Feature Descriptions PMBus Interface Capability The 6A Digital Pico DLynxTM power modules have a PMBus interface that supports both communication and control. The PMBus Power Management Protocol Specification can be obtained from www.pmbus.org. The modules support a subset of version 1.1 of the specification (see Table 6 for a list of the specific commands supported). Most module parameters can be programmed using PMBus and stored as defaults for later use. All communication over the module PMBus interface must support the Packet Error Checking (PEC) scheme. The PMBus master must generate the correct PEC byte for all transactions, and check the PEC byte returned by the module. The module also supports the SMBALERT response protocol whereby the module can alert the bus master if it wants to talk. For more information on the SMBus alert response protocol, see the System Management Bus (SMBus) specification. The module has non-volatile memory that is used to store configuration settings. Not all settings programmed into the device are automatically saved into this nonvolatile memory, only those specifically identified as capable of being stored can be saved (see Table 6 for which command parameters can be saved to nonvolatile storage). digit. The resistor values suggested for each digit are shown in Table 4 (1% tolerance resistors are recommended). Note that if either address resistor value is outside the range specified in Table 4, the module will respond to address 127. Table 4 Digit 0 1 2 3 4 5 6 7 2 The user must know which I C addresses are reserved in a system for special functions and set the address of the module to avoid interfering with other system operations. Both 100kHz and 400kHz bus speeds are supported by the module. Connection for the PMBus interface should follow the High Power DC specifications given in section 3.1.3 in the SMBus specification V2.0 for the 400kHz bus speed or the Low Power DC specifications in section 3.1.2. The complete SMBus specification is available from the SMBus web site, smbus.org. PMBus Data Format ADDR1 For commands that set thresholds, voltages or report such quantities, the module supports the “Linear” data format among the three data formats supported by PMBus. The Linear Data Format is a two byte value with an 11-bit, two’s complement mantissa and a 5-bit, two’s complement exponent. The format of the two data bytes is shown below: Data Byte High Data Byte Low 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Exponent Mantissa MSB MSB The value is of the number is then given by Value = Mantissa x 2 PMBus Addressing Exponent The power module can be addressed through the PMBus using a device address. The module has 64 possible addresses (0 to 63 in decimal) which can be set using resistors connected from the ADDR0 and ADDR1 pins to SIG_GND. Note that some of these addresses (0, 1, 2, 3, 4, 5, 6, 7, 8, 12, 40 in decimal) are reserved according to the SMBus specifications and may not be useable. The address is set in the form of two octal (0 to 7) digits, with each pin setting one digit. The ADDR1 pin sets the high order digit and ADDR0 sets the low order LINEAGE POWER Resistor Value (K) 10 15.4 23.7 36.5 54.9 84.5 130 200 ADDR0 RADDR0 RADDR1 SIG_GND Figure 48. Circuit showing connection of resistors used to set the PMBus address of the module. PMBus Enabled On/Off The module can also be turned on and off via the PMBus interface. The OPERATION command is used to actually turn the module on and off via the PMBus, while the ON_OFF_CONFIG command configures the combination of analog ON/OFF pin input and PMBus commands needed to turn the module on and off. Bit [7] in the OPERATION command data byte enables the module, with the following functions: 0 1 : : Output is disabled Output is enabled This module uses the lower five bits of the ON_OFF_CONFIG data byte to set various ON/OFF options as follows: 19 Preliminary Data Sheet October 17, 2011 Bit Position Access Function Default Value 4 r/w PU 1 3 r/w CMD 0 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current 2 r/w CPR 1 1 r/w POL 1 0 r CPA 1 PU: Sets the default to either operate any time input power is present or for the ON/OFF to be controlled by the analog ON/OFF input and the PMBus OPERATION command. This bit is used together with the CP, CMD and ON bits to determine startup. Bit Value 0 1 Action Module powers up any time power is present regardless of state of the analog ON/OFF pin Module does not power up until commanded by the analog ON/OFF pin and the OPERATION command as programmed in bits [2:0] of the ON_OFF_CONFIG register. CMD: The CMD bit controls how the device responds to the OPERATION command. Bit Value 0 1 Action Module ignores the ON bit in the OPERATION command Module responds to the ON bit in the OPERATION command CPR: Sets the response of the analog ON/OFF pin. This bit is used together with the CMD, PU and ON bits to determine startup. Bit Value 0 1 Action Module ignores the analog ON/OFF pin, i.e. ON/OFF is only controlled through the PMBUS via the OPERATION command Module requires the analog ON/OFF pin to be asserted to start the unit PMBus Adjustable Soft Start Rise Time The soft start rise time can be adjusted in the module via PMBus. When setting this parameter, make sure that the charging current for output capacitors can be delivered by the module in addition to any load current to avoid nuisance tripping of the overcurrent protection circuitry during startup. The TON_RISE command sets the rise time in ms, and allows choosing soft start times between 600ʅs and 9ms, with possible values listed in Table 5. Note that the exponent is fixed at -4 (decimal) and the upper two bits of the mantissa are also fixed at 0. Table 5 Rise Time 600ʅs 900ʅs 1.2ms 1.8ms 2.7ms 4.2ms 6.0ms 9.0ms Exponent 11100 11100 11100 11100 11100 11100 11100 11100 Mantissa 00000001010 00000001110 00000010011 00000011101 00000101011 00001000011 00001100000 00010010000 Output Voltage Adjustment Using the PMBus The VOUT_SCALE_LOOP parameter is important for a number of PMBus commands related to output voltage trimming, margining, over/under voltage protection and the PGOOD thresholds. The output voltage of the module is set as the combination of the voltage divider formed by RTrim and a 20k upper divider resistor inside the module, and the internal reference voltage of the module. The reference voltage VREF is nominally set at 600mV, and the output regulation voltage is then given by ª 20000 + RTrim º VOUT = « »¼ × VREF RTrim ¬ Hence the module output voltage is dependent on the value of RTrim which is connected external to the module. The information on the output voltage divider ratio is conveyed to the module through the VOUT_SCALE_LOOP parameter which is calculated as follows: VOUT _ SCALE _ LOOP = RTrim 20000+ RTrim The VOUT_SCALE_LOOP parameter is specified using the “Linear” format and two bytes. The upper five bits [7:3] of the high byte are used to set the exponent which is fixed at –9 (decimal). The remaining three bits of the high byte [2:0] and the eight bits of the lower byte are used for the mantissa. The default value of the mantissa is 00100000000 corresponding to 256 (decimal), corresponding to a divider ratio of 0.5. The maximum value of the mantissa is 512 corresponding to a divider ratio of 1. Note that the resolution of the VOUT_SCALE_LOOP command is 0.2%. When PMBus commands are used to trim or margin the output voltage, the value of VREF is what is changed inside the module, which in turn changes the regulated output voltage of the module. The nominal output voltage of the module can be adjusted with a minimum step size of 0.4% over a ±25% range from nominal using the VOUT_TRIM command over the PMBus. The VOUT_TRIM command is used to apply a fixed offset voltage to the output voltage command value LINEAGE POWER 20 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current using the “Linear” mode with the exponent fixed at –10 (decimal). The value of the offset voltage is given by VOUT ( offset ) = VOUT _ TRIM × 2 −10 This offset voltage is added to the voltage set through the divider ratio and nominal VREF to produce the trimmed output voltage. The valid range in two’s complement for this command is –4000h to 3999h. The high order two bits of the high byte must both be either 0 or 1. If a value outside of the +/-25% adjustment range is given with this command, the module will set it’s output voltage to the nominal value (as if VOUT_TRIM had been set to 0), assert SMBALRT#, set the CML bit in STATUS_BYTE and the invalid data bit in STATUS_CML. Output Voltage Margining Using the PMBus The module can also have its output voltage margined via PMBus commands. The command VOUT_MARGIN_HIGH sets the margin high voltage, while the command VOUT_MARGIN_LOW sets the margin low voltage. Both the VOUT_MARGIN_HIGH and VOUT_MARGIN_LOW commands use the “Linear” mode with the exponent fixed at –10 (decimal). Two bytes are used for the mantissa with the upper bit [7] of the high byte fixed at 0. The actual margined output voltage is a combination of the VOUT_MARGIN_HIGH or VOUT_MARGIN_LOW and the VOUT_TRIM values as shown below. VOUT( MH ) = (VOUT _ MARGIN_ HIGH + VOUT _ TRIM) × 2 −10 VOUT( ML) = (VOUT _ MARGIN _ LOW + VOUT _ TRIM) × 2 −10 Note that the sum of the margin and trim voltages cannot be outside the ±25% window around the nominal output voltage. The data associated with VOUT_MARGIN_HIGH and VOUT_MARGIN_LOW can be stored to non-volatile memory using the STORE_DEFAULT_ALL command. The module is commanded to go to the margined high or low voltages using the OPERATION command. Bits [5:2] are used to enable margining as follows: 00XX 0101 0110 1001 1010 : : : : : Margin Off Margin Low (Ignore Fault) Margin Low (Act on Fault) Margin High (Ignore Fault) Margin High (Act on Fault) PMBus Adjustable Overcurrent Warning The module can provide an overcurrent warning via the PMBus. The threshold for the overcurrent warning can be set using the parameter IOUT_OC_WARN_LIMIT. This command uses the “Linear” data format with a two byte data word where the upper five bits [7:3] of the high byte represent the exponent and the remaining three bits of the high byte [2:0] and the eight bits in the low byte represent the mantissa. The exponent is fixed at – 1 (decimal). The upper six bits of the mantissa are fixed LINEAGE POWER at 0 while the lower five bits are programmable with a default value of TBD (decimal). The resolution of this warning limit is 500mA. The value of the IOUT_OC_WARN_LIMIT can be stored to non-volatile memory using the STORE_DEFAULT_ALL command. Temperature Status via PMBus The module can provide information related to temperature of the module through the STATUS_TEMPERATURE command. The command returns information about whether the pre-set over temperature fault threshold and/or the warning threshold have been exceeded. PMBus Adjustable Output Over and Under Voltage Protection The module has output over and under voltage protection capability. The PMBus command VOUT_OV_FAULT_LIMIT is used to set the output over voltage threshold from four possible values: 108%, 110%, 112% or 115% of the commanded output voltage. The command VOUT_UV_FAULT_LIMIT sets the threshold that causes an output under voltage fault and can also be selected from four possible values: 92%, 90%, 88% or 85%. The default values are 112% and 88% of commanded output voltage. Both commands use two data bytes formatted as two’s complement binary integers. The “Linear” mode is used with the exponent fixed to –10 (decimal) and the effective over or under voltage trip points given by: VOUT (OV _ REQ ) = (VOUT _ OV _ FAULT _ LIMIT ) × 2 −10 VOUT (UV _ REQ ) = (VOUT _ UV _ FAULT _ LIMIT ) × 2 −10 Values within the supported range for over and undervoltage detection thresholds will be set to the nearest fixed percentage. Note that the correct value for VOUT_SCALE_LOOP must be set in the module for the correct over or under voltage trip points to be calculated. In addition to adjustable output voltage protection, the 6A Digital Pico DLynxTM module can also be programmed for the response to the fault. The VOUT_OV_FAULT RESPONSE and VOUT_UV_FAULT_RESPONSE commands specify the response to the fault. Both these commands use a single data byte with the possible options as shown below. 1. Continue operation without interruption (Bits [7:6] = 00, Bits [5:3] = xxx) 2. Continue for four switching cycles and then shut down if the fault is still present, followed by no restart or continuous restart (Bits [7:6] = 01, Bits [5:3] = 000 means no restart, Bits [5:3] = 111 means continuous restart) 3. Immediate shut down followed by no restart or continuous restart (Bits [7:6] = 10, Bits [5:3] = 000 means no restart, Bits [5:3] = 111 means continuous restart). 4. Module output is disabled when the fault is present and the output is enabled when the 21 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current fault no longer exists (Bits [7:6] = 11, Bits [5:3] = xxx). Note that separate response choices are possible for output over voltage or under voltage faults. PMBus Adjustable Input Undervoltage Lockout The module allows adjustment of the input under voltage lockout and hysteresis. The command VIN_ON allows setting the input voltage turn on threshold, while the VIN_OFF command sets the input voltage turn off threshold. For the VIN_ON command, possible values are 2.75V, and 3V to 14V in 0.5V steps. For the VIN_OFF command, possible values are 2.5V to 14V in 0.5V steps. If other values are entered for either command, they will be mapped to the closest of the allowed values. Both the VIN_ON and VIN_OFF commands use the “Linear” format with two data bytes. The upper five bits represent the exponent (fixed at -2) and the remaining 11 bits represent the mantissa. For the mantissa, the four most significant bits are fixed at 0. Power Good The module provides a Power Good (PGOOD) signal that is implemented with an open-drain output to indicate that the output voltage is within the regulation limits of the power module. The PGOOD signal will be deasserted to a low state if any condition such as overtemperature, overcurrent or loss of regulation occurs that would result in the output voltage going outside the specified thresholds. The PGOOD thresholds are user selectable via the PMBus (the default values are as shown in the Feature Specifications Section). Each threshold is set up symmetrically above and below the nominal value. The POWER_GOOD_ON command sets the output voltage level above which PGOOD is asserted (lower threshold). For example, with a 1.2V nominal output voltage, the POWER_GOOD_ON threshold can set the lower threshold to 1.14 or 1.1V. Doing this will automatically set the upper thresholds to 1.26 or 1.3V. The POWER_GOOD_OFF command sets the level below which the PGOOD command is de-asserted. This command also sets two thresholds symmetrically placed around the nominal output voltage. Normally, the POWER_GOOD_ON threshold is set higher than the POWER_GOOD_OFF threshold. Both POWER_GOOD_ON and POWER_GOOD_OFF commands use the “Linear” format with the exponent fixed at –10 (decimal). The two thresholds are given by VOUT ( PGOOD _ ON ) = ( POWER _ GOOD _ ON ) × 2 −10 VOUT ( PGOOD _ OFF ) = ( POWER _ GOOD _ OFF ) × 2 −10 Both commands use two data bytes with bit [7] of the high byte fixed at 0, while the remaining bits are r/w and used to set the mantissa using two’s complement representation. Both commands also use the VOUT_SCALE_LOOP parameter so it must be set correctly. The default value of POWER_GOOD_ON is set at 1.1035V and that of the POWER_GOOD_OFF is LINEAGE POWER set at 1.08V. The values associated with these commands can be stored in non-volatile memory using the STORE_DEFAULT_ALL command. The PGOOD terminal can be connected through a pullup resistor (suggested value 100KΩ) to a source of 5VDC or lower. Measurement of Output Current, Output Voltage and Input Voltage The module is capable of measuring key module parameters such as output current and voltage and input voltage and providing this information through the PMBus interface. Roughly every 200ȝs, the module makes 16 measurements each of output current, voltage and input voltage. Average values of of these 16 measurements are then calculated and placed in the appropriate registers. The values in the registers can then be read using the PMBus interface. Measuring Output Current Using the PMBus The module measures current by using the inductor winding resistance as a current sense element. The inductor winding resistance is then the current gain factor used to scale the measured voltage into a current reading. This gain factor is the argument of the IOUT_CAL_GAIN command, and consists of two bytes in the linear data format. The exponent uses the upper five bits [7:3] of the high data byte in two-s complement format and is fixed at –15 (decimal). The remaining 11 bits in two’s complement binary format represent the mantissa. During manufacture, each module is calibrated by measuring and storing the current gain factor into non-volatile storage. The current measurement accuracy is also improved by each module being calibrated during manufacture with the offset in the current reading. The IOUT_CAL_OFFSET command is used to store and read the current offset. The argument for this command consists of two bytes composed of a 5-bit exponent (fixed at -4d) and a 11-bit mantissa. This command has a resolution of 62.5mA and a range of -4000mA to +3937.5mA. The READ_IOUT command provides module average output current information. This command only supports positive or current sourced from the module. If the converter is sinking current a reading of 0 is provided. The READ_IOUT command returns two bytes of data in the linear data format. The exponent uses the upper five bits [7:3] of the high data byte in two-s complement format and is fixed at –4 (decimal). The remaining 11 bits in two’s complement binary format represent the th mantissa with the 11 bit fixed at 0 since only positive numbers are considered valid. Note that the current reading provided by the module is not corrected for temperature. The temperature corrected current reading for module temperature TModule can be estimated using the following equation ࡵࡻࢁࢀǡࡻࡾࡾ ൌ ࡵࡾࡱࡰ̴ࡻࢁࢀ ሾሺࢀࡵࡺࡰ െ ሻ ൈ Ǥ ૢሿ 22 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current where IOUT_CORR is the temperature corrected value of the current measurement, IREAD_OUT is the module current measurement value, TIND is the temperature of the inductor winding on the module. Since it may be difficult to measure TIND, it may be approximated by an estimate of the module temperature. Measuring Output Voltage Using the PMBus The module can provide output voltage information using the READ_VOUT command. The command returns two bytes of data all representing the mantissa while the exponent is fixed at -10 (decimal). During manufacture of the module, offset and gain correction values are written into the non-volatile memory of the module. The command VOUT_CAL_OFFSET can be used to read and/or write the offset (two bytes consisting of a 16-bit mantissa in two’s complement format) while the exponent is always fixed at -10 (decimal). The allowed range for this offset correction is -125 to 124mV. The command VOUT_CAL_GAIN can be used to read and/or write the gain correction - two bytes consisting of a five-bit exponent (fixed at -8) and a 11-bit mantissa. The range of this correction factor is -0.125V to +0.121V, with a resolution of 0.004V. The corrected output voltage reading is then given by: VOUT ( Final) = [VOUT ( Initial) × (1 + VOUT _ CAL _ GAIN)] + VOUT _ CAL _ OFFSET Measuring Input Voltage Using the PMBus The module can provide output voltage information using the READ_VIN command. The command returns two bytes of data in the linear format. The upper five bits [7:3] of the high data form the two’s complement representation of the mantissa which is fixed at –5 (decimal). The remaining 11 bits are used for two’s complement representation of the mantissa, with the th 11 bit fixed at zero since only positive numbers are valid. During module manufacture, offset and gain correction values are written into the non-volatile memory of the module. The command VIN_CAL_OFFSET can be used to read and/or write the offset - two bytes consisting of a five-bit exponent (fixed at -5) and a11-bit mantissa in two’s complement format. The allowed range for this offset correction is -2 to 1.968V, and the resolution is 32mV. The command VIN_CAL_GAIN can be used to read and/or write the gain correction - two bytes consisting of a five-bit exponent (fixed at -8) and a 11-bit mantissa. The range of this correction factor is -0.125V to +0.121V, with a resolution of 0.004V. The corrected output voltage reading is then given by: LINEAGE POWER VIN ( Final) = [VIN ( Initial) × (1 + VIN _ CAL _ GAIN)] + VIN _ CAL _ OFFSET Reading the Status of the Module using the PMBus The module supports a number of status information commands implemented in PMBus. However, not all features are supported in these commands. A 1 in the bit position indicates the fault that is flagged. STATUS_BYTE : Returns one byte of information with a summary of the most critical device faults. Bit Default Flag Position Value 7 X 0 6 OFF 0 5 VOUT Overvoltage 0 4 IOUT Overcurrent 0 3 VIN Undervoltage 0 2 Temperature 0 1 CML (Comm. Memory Fault) 0 0 None of the above 0 STATUS_WORD : Returns two bytes of information with a summary of the module’s fault/warning conditions. Low Byte Bit Default Flag Position Value 7 X 0 6 OFF 0 5 VOUT Overvoltage 0 4 IOUT Overcurrent 0 3 VIN Undervoltage 0 2 Temperature 0 1 CML (Comm. Memory Fault) 0 0 None of the above 0 High Byte Bit Position 7 6 5 4 3 2 1 0 Flag VOUT fault or warning IOUT fault or warning X X POWER_GOOD# (is negated) X X X Default Value 0 0 0 0 0 0 0 0 STATUS_VOUT : Returns one byte of information relating to the status of the module’s output voltage related faults. Bit Position 7 6 Flag VOUT OV Fault X Default Value 0 0 23 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current 5 X 0 4 VOUT UV Fault 0 3 X 0 2 X 0 1 X 0 0 X 0 STATUS_IOUT : Returns one byte of information relating to the status of the module’s output voltage related faults. Bit Position 7 6 5 4 3 2 1 0 Flag IOUT OC Fault X IOUT OC Warning X X X X X Default Value 0 0 0 0 0 0 0 0 MFR_SPECIFIC_00 : Returns information related to the type of module and revision number. Bits [7:2] in the Low Byte indicate the module type (000110 corresponds to the PDT006 series of module), while bits [7:3] indicate the revision number of the module. Low Byte Bit Position 7:2 1:0 Flag Module Name Reserved High Byte Bit Position 7:3 2:0 Flag Module Revision Number Reserved STATUS_TEMPERATURE : Returns one byte of information relating to the status of the module’s temperature related faults. Bit Position 7 6 5 4 3 2 1 0 Flag OT Fault OT Warning X X X X X X Default Value 0 0 0 0 0 0 0 0 STATUS_CML : Returns one byte of information relating to the status of the module’s communication related faults. Bit Position 7 6 5 4 3 2 1 0 Flag Invalid/Unsupported Command Invalid/Unsupported Command Packet Error Check Failed X X X Other Communication Fault X Default Value 0 0 0 0 0 0 0 0 MFR_VIN_MIN : Returns minimum input voltage as two data bytes of information in Linear format (upper five bits are exponent – fixed at -2, and lower 11 bits are mantissa in two’s complement format – fixed at 12) MFR_VOUT_MIN : Returns minimum output voltage as two data bytes of information in Linear format (upper five bits are exponent – fixed at -10, and lower 11 bits are mantissa in two’s complement format – fixed at 614) LINEAGE POWER Default Value 000110 10 24 Default Value None 000 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Summary of Supported PMBus Commands Please refer to the PMBus 1.1 specification for more details of these commands. Table 6 Hex Code Command Non-Volatile Memory Storage Brief Description Turn Module on or off. Also used to margin the output voltage 01 OPERATION Format Bit Position Access Function Default Value 7 r/w On 0 6 r X 0 Unsigned Binary 4 3 2 r/w r/w r/w Margin 0 0 0 0 5 r/w 1 r X X 0 r X X Configures the ON/OFF functionality as a combination of analog ON/OFF pin and PMBus commands Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access r/w r r r r r/w r/w r/w Function X X X pu cmd pol cpa X Default Value 0 0 0 1 0 1 1 1 02 ON_OFF_CONFIG 03 CLEAR_FAULTS Clear any fault bits that may have been set, also releases the SMBALERT# signal if the device has been asserting it. 10 WRITE_PROTECT Used to control writing to the module via PMBus. Copies the current register setting in the module whose command code matches the value in the data byte into non-volatile memory (EEPROM) on the module Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access x x r/w r/w r/w x x x Function bit7 bit6 bit5 X X X X X Default Value 0 0 0 X X X X X Bit5: 0 – Enables all writes as permitted in bit6 or bit7 1 – Disables all writes except the WRITE_PROTECT, OPERATION and ON_OFF_CONFIG (bit 6 and bit7 must be 0) Bit 6: 0 – Enables all writes as permitted in bit5 or bit7 1 – Disables all writes except for the WRITE_PROTECT and OPERATION commands (bit5 and bit7 must be 0) Bit7: 0 – Enables all writes as permitted in bit5 or bit6 1 – Disables all writes except for the WRITE_PROTECT command (bit5 and bit6 must be 0) 11 STORE_DEFAULT_ALL Copies all current register settings in the module into non-volatile memory (EEPROM) on the module. Takes about 50ms for the command to execute. 12 RESTORE_DEFAULT_ALL Restores all current register settings in the module from values in the module non-volatile memory (EEPROM) STORE_DEFAULT_CODE Copies the current register setting in the module whose command code matches the value in the data byte into non-volatile memory (EEPROM) on the module Bit Position 7 6 5 4 3 2 1 0 Access w w w w w w w w Function Command code RESTORE_DEFAULT_CODE Restores the current register setting in the module whose command code matches the value in the data byte from the value in the module non-volatile memory (EEPROM) Bit Position 7 6 5 4 3 2 1 0 Access w w w w w w w w Function Command code VOUT_MODE The module has MODE set to Linear and Exponent set to -10. These values cannot be changed Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Mode Exponent Default Value 0 0 0 1 0 1 1 0 13 14 20 LINEAGE POWER YES YES 25 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Table 6 (continued) Hex Code 22 25 26 29 35 Command VOUT_TRIM Apply a fixed offset voltage to the output voltage command value Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r/w r/w r/w r/w r/w r/w r/w Function High Byte Default Value 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 Access r/w r/w r/w r/w r/w r/w r/w Function Low Byte Default Value 0 0 0 0 0 0 0 VOUT_MARGIN_HIGH Sets the target voltage for margining the output high Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r r/w r/w r/w r/w r/w r/w Function High Byte Default Value 0 0 0 0 0 1 0 Bit Position 7 6 5 4 3 2 1 Access r/w r/w r/w r/w r/w r/w r/w Function Low Byte Default Value 0 1 0 0 0 1 1 VOUT_MARGIN_LOW VOUT_SCALE_LOOP VIN_ON LINEAGE POWER Non-Volatile Memory Storage Brief Description 0 r/w 0 0 r/w YES 0 0 r/w 1 0 r/w YES 1 Sets the target voltage for margining the output low Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r/w r r/w r/w r/w r/w r/w Function High Byte Default Value 0 0 0 0 0 1 0 Bit Position 7 6 5 4 3 2 1 Access r/w r/w r/w r/w r/w r/w r/w Function Low Byte Default Value 0 1 0 1 0 0 0 0 r/w 0 0 r/w YES 1 Sets the scaling of the output voltage – equal to the feedback resistor divider ratio Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r/w r r r r r r Function Exponent Mantissa Default Value 1 0 1 1 1 0 0 Bit Position 7 6 5 4 3 2 1 Access r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 0 0 0 0 Sets the value of input voltage at which the module turns on Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Function Exponent Mantissa Default Value 1 1 1 1 0 0 0 Bit Position 7 6 5 4 3 2 1 Access r/w r r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 0 1 0 1 26 0 r/w YES 1 0 r/w 0 0 r 0 0 r/w 1 YES Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Table 6 (continued) Hex Code 36 38 39 40 41 Command VIN_OFF Non-Volatile Memory Storage Brief Description Sets the value of input voltage at which the module turns off Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Function Exponent Mantissa Default Value 1 1 1 1 0 0 0 Bit Position 7 6 5 4 3 2 1 Access r/w r r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 0 1 0 1 0 r 0 0 r/w YES 0 IOUT_CAL_GAIN Returns the value of the gain correction term used to correct the measured output current Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r/w Function Exponent Mantissa Default Value 1 0 0 0 1 0 0 V Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value V: Variable based on factory calibration YES IOUT_CAL_OFFSET Returns the value of the offset correction term used to correct the measured output current Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r/w Function Exponent Mantissa Default Value 1 1 1 0 0 V 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r r r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 V: Variable based on factory calibration YES Sets the voltage level for an output overvoltage fault Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r/w r r/w r/w r/w r/w r/w Function High Byte Default Value 0 0 0 0 0 1 0 Bit Position 7 6 5 4 3 2 1 Access r/w r/w r/w r/w r/w r/w r/w Function Low Byte Default Value 0 0 0 0 1 0 1 YES VOUT_OV_FAULT_LIMIT Instructs the module on what action to take in response to a output overvoltage fault Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 VOUT_OV_FAULT_RESPONSE Access r/w r/w r/w r/w r/w r r RSP RSP Function RS[2] RS[1] RS[0] X X [1] [0] Default Value 1 1 1 1 1 1 0 LINEAGE POWER 0 r/w 1 0 r/w 0 0 r YES X 0 27 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Table 6 (continued) Hex Code 44 45 4A 5E 5F Command VOUT_UV_FAULT_LIMIT Non-Volatile Memory Storage Brief Description Sets the voltage level for an output undervoltage fault Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r/w r r/w r/w r/w r/w r/w Function High Byte Default Value 0 0 0 0 0 1 0 Bit Position 7 6 5 4 3 2 1 Access r/w r/w r/w r/w r/w r/w r/w Function Low Byte Default Value 1 0 0 0 1 1 1 0 r/w 0 0 r/w 1 Instructs the module on what action to take in response to a output undervoltage fault Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 VOUT_UV_FAULT_RESPONSE Access r r/w r/w r/w r/w r/w r RSP RSP Function RS[2] RS[1] RS[0] X X [1] [0] Default Value 0 0 0 0 0 1 0 IOUT_OC_WARN_LIMIT YES Sets the output overcurrent warning level in A Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Function Exponent Mantissa Default Value 1 1 1 1 1 0 0 Bit Position 7 6 5 4 3 2 1 Access r/w r r r/w r/w r/w r/w Function Mantissa Default Value 0 0 tbd tbd tbd tbd tbd 0 r YES X 0 0 r 0 0 r/w YES tbd POWER_GOOD_ON Sets the output voltage level at which the PGOOD pin is asserted high Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r/w r/w r/w r/w r/w r/w r/w Function High Byte Default Value 0 0 0 0 0 1 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Low Byte Default Value 0 1 1 0 1 0 1 0 YES POWER_GOOD_OFF Sets the output voltage level at which the PGOOD pin is de-asserted low Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r/w r/w r/w r/w r/w r/w r/w Function High Byte Default Value 0 0 0 0 0 1 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Low Byte Default Value 0 1 0 1 0 0 1 0 YES LINEAGE POWER 28 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Table 6 (continued) Hex Code 61 78 79 7A 7B 7D Command TON_RISE Non-Volatile Memory Storage Brief Description Sets the rise time of the output voltage during startup Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Function Exponent Mantissa Default Value 1 1 1 0 0 0 0 Bit Position 7 6 5 4 3 2 1 Access r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 1 0 1 0 1 0 r/w 0 0 r/w 0 STATUS_BYTE Returns one byte of information with a summary of the most critical module faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r VOUT IOUT VIN_ OTHE Flag X OFF TEMP CML _OV _OC UV R Default Value 0 0 0 0 0 0 0 0 STATUS_WORD Returns two bytes of information with a summary of the module’s fault/warning conditions Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r IOUT PGO Flag VOUT X X X X X _OC OD Default Value 0 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r VOUT IOUT VIN_ OTHE Flag X OFF TEMP CML _OV _OC UV R Default Value 0 0 0 0 0 0 0 0 STATUS_VOUT Returns one byte of information with the status of the module’s output voltage related faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Flag VOUT_OV X X VOUT_UV X X X X Default Value 0 0 0 0 0 0 0 0 STATUS_IOUT Returns one byte of information with the status of the module’s output current related faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Flag IOUT_OC X X X IOUT_OC_WARN X X Default Value 0 0 0 0 0 0 0 STATUS_TEMPERATURE LINEAGE POWER YES 0 r X 0 Returns one byte of information with the status of the module’s temperature related faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Flag OT_FAULT OT_WARN X X X X X X Default Value 0 0 0 0 0 0 0 0 29 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Table 6 (continued) Hex Code 7E 88 8B 8C 98 A0 Command STATUS_CML READ_VIN READ_VOUT READ_IOUT Non-Volatile Memory Storage Brief Description Returns one byte of information with the status of the module’s communication related faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Other Invalid Invalid PEC Flag X X X Comm Command Data Fail Fault Default Value 0 0 0 0 0 0 0 Returns the value of the input voltage applied to the module Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Function Exponent Mantissa Default Value 1 1 0 1 1 0 0 Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Function Mantissa Default Value 0 0 0 0 0 0 0 Returns the value of the output voltage of the module Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 Access r r r r r r Function Mantissa Default Value 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 Access r r r r r r Function Mantissa Default Value 0 0 0 0 0 0 0 r X 0 0 r 0 0 r 0 1 r 0 r 0 1 r 0 0 r 0 0 Returns the value of the output current of the module Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Function Exponent Mantissa Default Value 1 1 1 0 0 0 0 Bit Position 7 6 5 4 3 2 1 Access r r r r r r r Function Mantissa Default Value 0 0 0 0 0 0 0 0 r 0 0 r 0 PMBUS_REVISION Returns one byte indicating the module is compliant to PMBus Spec. 1.1 (read only) Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Default Value 0 0 0 1 0 0 0 1 YES MFR_VIN_MIN Returns the minimum input voltage the module is specified to operate at (read only) Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Exponent Mantissa Default Value 1 1 1 1 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Mantissa Default Value 0 0 0 0 1 1 0 0 YES LINEAGE POWER 30 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Table 6 (continued) Hex Code A4 D0 D4 D5 D6 Command MFR_VOUT_MIN MFR_SPECIFIC_00 Non-Volatile Memory Storage Brief Description Returns the minimum output voltage possible from the module (read only) Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Exponent Mantissa Default Value 0 0 0 0 0 0 1 0 Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Mantissa Default Value 0 1 1 0 0 1 1 0 YES Returns module name information (read only) Format Unsigned Binary Bit Position 7 6 5 4 3 Access r r r r r Function Reserved Default Value 1 1 1 0 1 Bit Position 7 6 5 4 3 Access r r r r r Function Module Name Default Value 0 0 0 1 1 YES 2 r 1 r 0 2 r 0 0 1 0 r r Reserved 1 0 0 0 r Applies an offset to the READ_VOUT command results to calibrate out offset errors in module measurements of the output voltage (between -125mV and +124mV) Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r/w r r r r r r r Function Mantissa Default Value V 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value V V V V V V V V YES VOUT_CAL_GAIN Applies a gain correction to the READ_VOUT command results to calibrate out gain errors in module measurements of the output voltage (between -0.125 and 0.121) Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r/w Function Exponent Mantissa Default Value 1 1 0 0 0 0 0 V Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value V V V V V V V V YES VIN_CAL_OFFSET Applies an offset correction to the READ_VIN command results to calibrate out offset errors in module measurements of the input voltage (between -2V and +1.968V) Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r/w r r r/w Function Exponent Mantissa Default Value 1 1 0 1 V 0 0 V Bit Position 7 6 5 4 3 2 1 0 Access r r r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 V V V V V V YES VOUT_CAL_OFFSET LINEAGE POWER 31 Preliminary Data Sheet October 17, 2011 Hex Code D7 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Command Brief Description Non-Volatile Memory Storage VIN_CAL_GAIN Applies a gain correction to the READ_VIN command results to calibrate out gain errors in module measurements of the input voltage (between -0.125 and 0.121) Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r/w r r r/w Function Exponent Mantissa Default Value 1 1 0 0 V 0 0 V Bit Position 7 6 5 4 3 2 1 0 Access r r r r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 V V V V V YES LINEAGE POWER 32 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Preliminary Data Sheet October 17, 2011 Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should always be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 49. The preferred airflow direction for the module is in Figure 50. The thermal reference points, Tref used in the specifications are also shown in Figure 50. For reliable operation the temperatures at these points should not exceed TBD. The output power of the module should not exceed the rated power of the module (Vo,set x Io,max). Please refer to the Application Note “Thermal Characterization Process For Open-Frame BoardMounted Power Modules” for a detailed discussion of thermal aspects including maximum device temperatures. 25.4_ (1.0) Wind Tunnel PWBs Power Module Figure 50. Preferred airflow direction and location of hot-spot of the module (Tref). 76.2_ (3.0) x 12.7_ (0.50) Probe Location for measuring airflow and ambient temperature Air flow Figure 49. Thermal Test Setup. LINEAGE POWER 33 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Example Application Circuit Requirements: Vin: 12V Vout: 1.8V Iout: 4.5A max., worst case load transient is from 3A to 4.5A ∆Vout: Vin, ripple 1.5% of Vout (27mV) for worst case load transient 1.5% of Vin (180mV, p-p) Vin+ Vout+ VOUT VS+ VIN PGOOD RTUNE MODULE SEQ CTUNE SEQ CI3 CI2 CI1 TRIM DATA CO1 ADDR0 SMBALRT# RTrim ADDR1 ON/OFF RADDR1 RADDR0 SIG_GND SYNC GND GND VS- CI1 Decoupling cap - 1x0.01µF/16V ceramic capacitor (e.g. Murata LLL185R71E103MA01) CI2 1x22µF/16V ceramic capacitor (e.g. Murata GRM32ER61C226KE20) CI3 47µF/16V bulk electrolytic CO1 Decoupling cap - 1x0.01µF/16V ceramic capacitor (e.g. Murata LLL185R71E103MA01) CO2 1 x 47µF/6.3V ceramic capacitor (e.g. Murata GRM31CR60J476ME19) CO3 CTune RTune 1 x 330µF/6.3V Polymer (e.g. Sanyo Poscap) 2200pF ceramic capacitor (can be 1206, 0805 or 0603 size) 178 ohms SMT resistor (can be 1206, 0805 or 0603 size) RTrim 10kΩ SMT resistor (can be 1206, 0805 or 0603 size, recommended tolerance of 0.1%) LINEAGE POWER 34 CO2 CO3 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Mechanical Outline Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) PIN FUNCTION PIN FUNCTION 1 ON/OFF 10 PGOOD 2 VIN 11 SYNC 3 GND 12 VS- 4 VOUT 13 SIG. GND 5 VS+ (SENSE) 14 SMBALERT 6 TRIM 15 DATA 7 GND 16 ADDR0 8 CLK 17 ADDR1 9 SEQ 1 PIN 7 1 If unused, connect to Ground. Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) 7 PIN 1 2 3 4 5 6 7 8 9 2 LINEAGE POWER FUNCTION ON/OFF VIN GND VOUT VS+ (SENSE) TRIM GND CLK SEQ PIN 10 11 12 13 14 15 16 17 FUNCTION PGOOD SYNC2 VSSIG_GND SMBALERT DATA ADDR0 ADDR1 If unused, connect to Ground 36 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Packaging Details The 12V Digital Pico DLynxTM 6A modules are supplied in tape & reel as standard. Modules are shipped in quantities of 200 modules per reel. All Dimensions are in millimeters and (in inches). Reel Dimensions: Outside Dimensions: Inside Dimensions: Tape Width: LINEAGE POWER 330.2 mm (13.00) 177.8 mm (7.00”) 24.00 mm (0.945”) 37 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Surface Mount Information Dwell time above 217 C: 60 seconds minimum Dwell time above 235 C: 5 to 15 second Pick and Place MSL Rating TM The 6A Digital Pico DLynx modules use an open frame construction and are designed for a fully automated assembly process. The modules are fitted with a label designed to provide a large surface area for pick and place operations. The label meets all the requirements for surface mount processing, as well as safety standards, and is able to withstand reflow o temperatures of up to 300 C. The label also carries product information such as product code, serial number and the location of manufacture. Nozzle Recommendations The module weight has been kept to a minimum by using open frame construction. Variables such as nozzle size, tip style, vacuum pressure and placement speed should be considered to optimize this process. The minimum recommended inside nozzle diameter for reliable operation is 3mm. The maximum nozzle outer diameter, which will safely fit within the allowable component spacing, is 7 mm. TM The 6A Digital Pico DLynx rating of 2. modules have a MSL Storage and Handling The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. B (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken until time of use. Once the original package is broken, the floor life of the product at conditions of ≤ 30°C and 60% relative humidity varies according to the MSL rating (see J-STD-033A). The shelf life for dry packed SMT packages will be a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40° C, < 90% relative humidity. Bottom Side / First Side Assembly This module is not recommended for assembly on the bottom side of a customer board. If such an assembly is attempted, components may fall off the module during the second reflow process. Lead Free Soldering TM The 12VDigital Pico DLynx 6A modules are lead-free (Pb-free) and RoHS compliant and are both forward and backward compatible in a Pb-free and a SnPb soldering process. Failure to observe the instructions below may result in the failure of or cause damage to the modules and can adversely affect long-term reliability. Pb-free Reflow Profile Power Systems will comply with J-STD-020 Rev. C (Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices) for both Pb-free solder profiles and MSL classification procedures. This standard provides a recommended forced-air-convection reflow profile based on the volume and thickness of the package (table 5-2). The suggested Pb-free solder paste is Sn/Ag/Cu (SAC). The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Fig. 51. Soldering outside of the recommended profile requires testing to verify results and performance. Figure 51. Recommended linear reflow profile using Sn/Ag/Cu solder. Post Solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Board Mounted Power Modules: Soldering and Cleaning Application Note (AN04-001). It is recommended that the pad layout include a test pad where the output pin is in the ground plane. The thermocouple should be attached to this test pad since this will be the coolest solder joints. The temperature of this point should be: Maximum peak temperature is 260 C. Minimum temperature is 235 C. LINEAGE POWER 38 Preliminary Data Sheet October 17, 2011 6A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules 3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 6A output current Ordering Information Please contact your Lineage Power Sales Representative for pricing, availability and optional features. Table 7. Device Codes Device Code Input Voltage Range Output Voltage Output Current On/Off Logic Sequencing Comcodes PDT006A0X3-SRZ 3 – 14.4Vdc 0.45 – 5.5Vdc 6A Negative Yes CC109159604 PDT006A0X43-SRZ 3 – 14.4Vdc 0.45 – 5.5Vdc 6A Positive Yes CC109159612 -Z refers to RoHS compliant parts Table 8. Coding Scheme Package Family Identifier Sequencing Output Option current P D T 006A0 P=Pico D=Dlynx Digital T=with EZ Sequence 6A V= DLynx Analog. X=without sequencing U=Micro M=Mega G=Giga Output voltage On/Off logic Remote Sense X 4 3 -SR -D Z 3= Remote Sense S= Surface Mount D = 105°C operating ambient, 40G operating shock as per MIL Std 810F Z = ROHS6 X= 4= programm positive able output No entry = negative Options R= Tape & Reel ROHS Compliance Asia-Pacific Headquarters Tel: +86.021.54279977*808 World Wide Headquarters Lineage Power Corporation 601 Shiloh Road, Plano, TX 75074, USA +1-888-LINEAGE(546-3243) (Outside U.S.A.: +1-972-244-WATT(9288)) www.lineagepower.com e-mail: [email protected] Europe, Middle-East and Africa Headquarters Tel: +49.89.878067-280 India Headquarters Tel: +91.80.28411633 Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Lineage Power DC-DC products are protected under various patents. Information on these patents is available at www.lineagepower.com/patents. © 2011 Lineage Power Corporation, (Plano, Texas) All International Rights Reserved. Lineage Power Digital Non-Isolated DC-DC products use technology licensed from Power-One, protected by US patents: US20040246754, US2004090219A1, US2004093533A1, US2004123164A1, US2004123167A1, US2004178780A1, US2004179382A1, US20050200344, US20050223252, US2005289373A1, US20060061214, US2006015616A1, US20060174145, US20070226526, US20070234095, US20070240000, US20080052551, US20080072080, US20080186006, US6741099, US6788036, US6936999, US6949916, US7000125, US7049798, US7068021, US7080265, US7249267, US7266709, US7315156, US7372682, US7373527, US7394445, US7456617, US7459892, US7493504, US7526660. Outside the US the Power-One licensed technology is protected by patents: AU3287379AA, AU3287437AA, AU3290643AA, AU3291357AA, CN10371856C, CN1045261OC, CN10458656C, CN10459360C, CN10465848C, CN11069332A, CN11124619A, CN11346682A, CN1685299A, CN1685459A, CN1685582A, CN1685583A, CN1698023A, CN1802619A, EP1561156A1, EP1561268A2, EP1576710A1, EP1576711A1, EP1604254A4, EP1604264A4, EP1714369A2, EP1745536A4, EP1769382A4, EP1899789A2, EP1984801A2, W004044718A1, W004045042A3, W004045042C1, W004062061 A1, W004062062A1, W004070780A3, W004084390A3, W004084391A3, W005079227A3, W005081771A3, W006019569A3, W02007001584A3, W02007094935A3 LINEAGE POWER 39 Document No: DS11-008 ver. 0.33 PDF name: PDT006A0X.pdf