FR301-FR309 3.0 AMP. Fast Recovery Rectifiers DO-201AD Features High efficiency, Low VF High current capability High reliability High surge current capability Low power loss. Mechanical Data Cases: Molded plastic Epoxy: UL 94V-0 rate flame retardant Polarity: Color band denotes cathode end High temperature soldering guaranteed: 260 oC/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs.,(2.3kg) tension Weight: 1.2 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length o @T A = 55 C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 3.0A o Maximum DC Reverse Current @ T A=25 C o at Rated DC Blocking Voltage @ T A=125 C Maximum Reverse Recovery Time ( Note 1) Typical Junction Capacitance ( Note 2 ) Typical Thermal resistance (Note 3) Operating Temperature Range Symbol V RRM V RMS V DC FR 301 50 35 50 FR 302 100 70 100 FR 303 200 140 200 FR 304 400 280 400 FR 305 600 420 600 FR 306 800 560 800 FR 307 1000 700 1000 FR Units FR 309 308 V 1200 1300 840 910 V 1200 1300 V I(AV) 3. 0 A IFSM 150 A VF 1. 2 V IR 5 150 uA uA nS pF o C/W o C o C Trr Cj R θJA TJ 150 250 500 60 40 -65 to +150 -65 to +150 Storage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF=0.5A, IR =1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 3. Mount on Cu-Pad Size 16mm x 16mm on P.C.B. http://www.luguang.cn mail:[email protected] FR301-FR309 3.0 AMP. Fast Recovery Rectifiers RATINGS AND CHARACTERISTIC CURVES (FR301 THRU FR309) FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG 1000 4 3 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT AMPERES FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 2 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375"(9.5mm) Lead Length 1 0 0 25 50 75 100 125 150 175 o AMBIENT TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 100 Tj=125 0C 10 Tj=75 0C 1.0 Tj=25 0C PEAK FORWARD SURGE CURRENT. (A) 150 0.1 0 100 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 50 Tj=25 0C FIG.5- TYPICAL FORWARD CHARACTERISTICS 8.3ms Single Half Sine Wave JEDEC Method 20 10 10 5 10 NUMBER OF CYCLES AT 60Hz 50 100 INSTANTANEOUS FORWARD CURRENT. (A) 1 FIG.4- TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE.(pF) 100 Tj=25 0C 60 40 20 3 1 0.3 0.1 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.03 0.01 0.4 10 1 2 4 6 10 20 40 60 100 0.6 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms http://www.luguang.cn 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm mail:[email protected] 1.6 1.8