502 series features • Ø8.1mm mounting • Nickel plated brass housing, Sealed to IP67 • Wide viewing angle • Water clear lens for good on/off contrast ratio • Internal reverse protection diode fitted as standard in all voltage models • Internally potted for use in high vibration applications • Pack Quantity = 10 Pieces specifications Typical characteristics (Ta = 25°C) Colour Number Luminous Intensity (mcd) Wave Length (nm) Operating Temp. (°C) Storage Temp. (°C) De-rating Vac/dc Current DC (mA) Voltage Graphs 502-930-21 Blue 12 Vdc 20 9870 465 -30 - +85 -40 - +100 U 502-997-21 White 12 Vdc 20 27000 * See below -30 - +85 -40 - +100 I 502-501-23 Red 28 Vdc 20 600 630 -40 - +80 -40 - +100 D 502-521-23 Yellow 28 Vdc 20 600 585 -40 - +80 -40 - +100 D 502-930-23 Blue 28 Vdc 20 9870 465 -30 - +85 -40 - +100 U 997F-C *Typical emission colour White x 0.31 - - - y 0.32 - - - ^ = Voltage for 20mA product is Vf at 20mA, not Vopr - Products must be de-rated according to the de-rating information. Each de-rating graph refers to specific LEDs. Please refer to graphs on page 3. - Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated. - Intensities (lv) and colour shades of white (x, y co-ordinates) may vary between LEDs within a batch to order to order please contact us on: t: +44 (0)1229 582 430 f: +44 (0)1229 585 155 e: [email protected] w: www.leds.co.uk © marl international limited technical documentation has been designed by marl international limited for the intention of providing information, which must not be copied or released to a third party without prior written consent from marl international limited. the information provided does not constitute part of any order or contract and should not be regarded as a representation relating to either products or service. no responsibility can be assumed for inaccuracies or printing errors. marl international limited reserve the right to alter without notice the specification or any conditions of supply for product or service. marl international limited - dsn 502 - version 2013-12-03-173358 BS EN ISO 9001:2008 approved manufacturer page 1 of 4 industrial panel lamps Part 502 series technical data 23.8 +0.1 8.1 0 6 2.8 7 11.5 7.8 Mounting Hole Anode termination indicated by red sleeve. Mounting hole to be clean and burr free. Dimensions in mm (typical) Not to scale housing material push on connectors Body Bright Nickel Plated Brass Nut Panel Seal Bright Nickel Plated Brass Termination Brass with Silver Flash finish Lens Polycarbonate Encapsulation PC5430 Resin Lock Washer Header Spring Steel Viton 925-000-00 is brass tin plated - for use with 502 series lamps Dimensions in mm (typical). Not to scale. - technical characteristics Series Max. Power Dissipation Max. Reverse Voltage Panel Cutout Nut Mounting Torque Min. Mounting Centres Max. Panel Thickness 502 700 3*/1000^ 8.1 0.6 14.5 1.5 - 13.0 units mW Vdc mm Nm mm mm * = Current version ^ = Voltage version optional flying lead terminators Order Code Suffix 15 15 19 19 Supply Voltage DC products AC products DC products AC products Wire Colour Red-anode/ Black-cathode Brown-live/ Blue-neutral Red-anode/ Black-cathode Brown-live/ Blue-neutral Wire Length 150mm 150mm 1000mm 1000mm No/Diameter of Conductor Diameter Insulation 19/0.15mm 1.2mm Comments Customised lengths available to order to order please contact us on: t: +44 (0)1229 582 430 f: +44 (0)1229 585 155 e: [email protected] w: www.leds.co.uk © marl international limited technical documentation has been designed by marl international limited for the intention of providing information, which must not be copied or released to a third party without prior written consent from marl international limited. the information provided does not constitute part of any order or contract and should not be regarded as a representation relating to either products or service. no responsibility can be assumed for inaccuracies or printing errors. marl international limited reserve the right to alter without notice the specification or any conditions of supply for product or service. marl international limited - dsn 502 - version 2013-12-03-173358 BS EN ISO 9001:2008 approved manufacturer page 2 of 4 502 series de-rating information Derating Graph I Derating Graph U 55 50 50 50 45 45 40 35 30 25 20 15 10 40 35 30 25 20 15 10 5 5 0 0.0 0 0.0 20.0 40.0 60.0 80.0 100.0 Ambient Temperature Ta (°C) 8.5 Forward Current IF (mA) 55 Forward Current IF (mA) Forward Current IF (mA) Derating Graph D 55 45 40 35 30 25 20 15 10 8.5 5 20.0 40.0 60.0 80.0 100.0 Ambient Temperature Ta (°C) 0 0.0 20.0 40.0 60.0 80.0 100.0 Ambient Temperature Ta (°C) also available Part numbers also available in the 502 series: Part Voltage Colour Number 502-501-20 502-501-86-19 502-930-21-19 Vopr Red Red Blue 5/6 Vdc 115 Vac 60 Hz 12 Vdc The products listed here illustrate all of the options available to order. These products may have custom modifications that alter their operation beyond the generic information contained within this datasheet. Please contact sales for further information. RP = Reverse Polarity to order to order please contact us on: t: +44 (0)1229 582 430 f: +44 (0)1229 585 155 e: [email protected] w: www.leds.co.uk © marl international limited technical documentation has been designed by marl international limited for the intention of providing information, which must not be copied or released to a third party without prior written consent from marl international limited. the information provided does not constitute part of any order or contract and should not be regarded as a representation relating to either products or service. no responsibility can be assumed for inaccuracies or printing errors. marl international limited reserve the right to alter without notice the specification or any conditions of supply for product or service. marl international limited - dsn 502 - version 2013-12-03-173358 BS EN ISO 9001:2008 approved manufacturer page 3 of 4 502 series design considerations Electro-Static Discharge (ESD) Build up of electro-static discharge occurs in many situations involving people moving and handling products. The range of possible situations is very diverse but voltage levels as high as several thousand volts can and do arise in many individual situations. When an operator charged up to these levels handles a static sensitive device, there is a very probable likelihood that the device will be irreversibly damaged. It is essential that precautions are taken at all stages during manufacture and assembly of these products. Although LEDs were never considered to be static sensitive devices, changes in manufacturing technology and materials used to produce higher intensity products over a large range of the wavelength spectrum have changed this. Marl has an approved system of ESD control from goods in, through production and into final packing and despatch. Marl recommend all users of LED based products follow the guidelines of BS 100015. Power De-Rating The forward voltage/ current value of an LED is dependant upon the ambient temperature of the environment in which it is operated. Therefore, care must be taken to operate the LED at the correct voltage/ current values, depending upon the ambient temperature. Consequently, a recommendation regarding operating voltages and currents is given in order to address these temperature effects. This recommendation is termed ‘de-rating’. It is usual for forward voltages and currents to be specified for ambient temperature of 25°C. However, because the values of these qualities vary with temperature, please refer to the de-rating graphs for correct operation. Marl accept no liability for any product that is operated higher than the stated voltage. to order to order please contact us on: t: +44 (0)1229 582 430 f: +44 (0)1229 585 155 e: [email protected] w: www.leds.co.uk © marl international limited technical documentation has been designed by marl international limited for the intention of providing information, which must not be copied or released to a third party without prior written consent from marl international limited. the information provided does not constitute part of any order or contract and should not be regarded as a representation relating to either products or service. no responsibility can be assumed for inaccuracies or printing errors. marl international limited reserve the right to alter without notice the specification or any conditions of supply for product or service. marl international limited - dsn 502 - version 2013-12-03-173358 BS EN ISO 9001:2008 approved manufacturer page 4 of 4