MICRODC IB1215NXT-1W

IB-XT-1W&IB-NXT-1W Series
1W,FIXED INPUT,ISOLATED & REGULATED SINGLE OUTPUT,SMD DC-DC CONVERTER
PRODUCT PROGRAM
Input
Part
Number
Output
Voltage(VDC)
Voltage
Efficiency
Current(MA)
(%,Typ)
(VDC)
Max
Min.
Nominal
Range
IB0505XT-W75
5
4.75-5.25
5
150
15
68
IB0512XT-1W
5
4.75-5.25
12
83
9
69
IB0515XT-1W
5
4.75-5.25
15
67
7
69
IB1205XT-W75
12
11.4-12.6
5
150
15
68
IB1212XT-1W
12
11.4-12.6
12
83
9
69
IB1215XT-1W
12
11.4-12.6
15
67
7
70
IB0505NXT-W75
5
4.75-5.25
5
150
15
68
◆No Heatsink Required
IB0512NXT-1W
5
4.75-5.25
12
83
9
69
◆Continuous Short Circuit Protection
IB0515NXT-1W
5
4.75-5.25
15
67
7
69
IB1205NXT-W75
12
11.4-12.6
5
150
15
68
◆Internal SMD Construction
IB1212NXT-1W
12
11.4-12.6
12
83
9
69
◆Temperature Range: -40℃~ +85℃
IB1215NXT-1W
12
11.4-12.6
15
67
7
70
◆Industry Standard Pinout
Note: 1. IB-NXT-1W series have no 3,6,8,9 pin, for example IB0505NXT-W75.
FEATURES
◆Small Footprint
◆SMD Package Style
◆1kVDC Isolation
◆No External Component Require
◆RoHS Compliance
MODEL SELECTION
IB①05②12③X④T⑤ -1W⑥
①Product Series
③Output Voltage
⑤SMD Package Style
②Input Voltage
④Fixed input
⑥Rated Power
MODEL SELECTION
IB①05②12③N④X⑤T⑥ -1W⑦
①Product Series
③Output Voltage
⑤Fixed input
⑦Rated Power
②Input Voltage
④No Pin
⑥SMD Package Style
COMMON SPECIFICATIONS
Item
Test Conditions
Min.
Typ.
Max.
Storage humidity
Operating temperature
-40
Storage temperature
-55
Temp. rise at full load
Lead temperature
15
1.5mm from case for 10 seconds
Cooling
Units
95
%
85
℃
125
℃
25
℃
260
℃
Free air convection
Short circuit protection
Continuous
Package material
Epoxy Resin (UL94-V0)
MTBF
3500
Weight
K hours
1.70
g
APPLICATIONS
The IB-XT-1W&IB-NXT-1W series are specially designed
for applications where a group of polar power supplies are
isolated from the input power supply in a distributed power
supply system on a circuit board.
These products apply to:
1) Where the voltage of the input power supply is fixed
(voltage variation≤±5%);
2) Where isolation is necessary between input and output
(isolation voltage≤1000VDC);
3) Where the regulation of the output voltage and the
output ripple noise are not demanding.
ISOLATION SPECIFICATIONS
Item
Test Conditions
Min.
Isolation voltage
Tested for 1 minute and 1mA max
1000
VDC
Isolation resistance
Test at 500VDC
1000
MΩ
Isolation capacitance
Typ.
Max.
40
MICRODC reserves the copyright
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 1 of 3
Units
pF
IB-XT-1W&IB-NXT-1W Series
TYPICAL CHARACTERISTICS
OUTPUT SPECIFICATIONS
Item
Test Conditions
Min.
Output power
Typ.
0.1
Max.
Units
1
W
±0.25
%
%
Line regulation
For Vin change of ±5%
Load regulation
10% to 100% load
±1
Output voltage accuracy
100% full load
±3
%
Temperature drift
100% full load
±0.03
%/℃
Ripple*
20MHz Bandwidth
10
20
mVp-p
Noise*
20MHz Bandwidth
50
100
mVp-p
Switching frequency
Full load, nominal input
100
operation
instructions
*Test
Testing
ripple
and
noise
by
"Parallel
cable" method.
See
detailed
KHz
at
of Power Converter section, application notes.
RECOMMENDED REFLOW SOLDERING PROFILE
RECOMMENDED CIRCUIT
APPLICATION NOTE
1) Requirement on output load
To ensure this module can operate efficiently and reliably , During operation , the minimum output
load could not be less than 10% of the full load . If the actual output power is very small , please connect
a resistor with proper resistance at the output end in parallel to increase the load.
2) Recommended testing circuit
If you want to further decrease the input/output ripple , an "LC" filtering network may be connected to
the input and output ends of the DC/DC converter, see (Figure 1).
It should also be noted that the inductance and the frequency of the "LC" filtering network should
be staggered with the DC/DC frequency to avoid mutual interference . However, the capacitance of the
output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For
every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of
its filter capacitor sees (Table 1).
3) Overload Protection
Under normal operating conditions, the output circuit of these products has no protection against
over-current . The simplest method is to connect a self-recovery fuse in series at the input end or add a
circuit breaker to the circuit .
4) When the environment temperature is higher than 71
71℃,, the product output power should be
less then 60% of the rated power
5) No parallel connection or plug and play
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 3
IB-XT-1W&IB-NXT-1W Series
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
MECHANICAL DIMENSIONS
TUBE OUTLINE DIMENSIONS
RECOMMENDED FOOTPRINT
REEL PACKING OUTLINE DIMENSIONS
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
REACH COMPLIANT INFORMATION
E-mail:[email protected]
Website:http://www.microdc.cn
http://www.microdc.cn
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 3 of 3