CY14B101Q1 CY14B101Q2 CY14B101Q3 1 Mbit (128 K x 8) Serial SPI nvSRAM Features ■ 1-Mbit nonvolatile static random access memory (nvSRAM) ❐ Internally organized as 128 K × 8 ❐ STORE to QuantumTrap nonvolatile elements initiated automatically on power-down (AutoStore) or by user using HSB pin (Hardware STORE) or SPI instruction (Software STORE) ❐ RECALL to SRAM initiated on power-up (Power-Up RECALL) or by SPI instruction (Software RECALL) ❐ Automatic STORE on power-down with a small capacitor (except for CY14B101Q1) ■ High reliability ❐ Infinite read, write, and RECALL cycles ❐ 1 million STORE cycles to QuantumTrap ❐ Data retention: 20 years ■ High speed serial peripheral interface (SPI) ❐ 40 MHz clock rate ❐ Supports SPI mode 0 (0,0) and mode 3 (1,1) ■ 8-pin dual flat no-lead (DFN) package and 16-pin small outline integrated circuit (SOIC) package ❐ Restriction of hazardous substances (RoHS) compliant ❐ Functional Overview The Cypress CY14B101Q1/CY14B101Q2/CY14B101Q3 combines a 1 Mbit nvSRAM with a nonvolatile element in each memory cell with serial SPI interface. The memory is organized as 128 K words of 8 bits each. The embedded nonvolatile elements incorporate the QuantumTrap technology, creating the world’s most reliable nonvolatile memory. The SRAM provides infinite read and write cycles, while the QuantumTrap cell provides highly reliable nonvolatile storage of data. Data transfers from SRAM to the nonvolatile elements (STORE operation) takes place automatically at power-down (except for CY14B101Q1). On power-up, data is restored to the SRAM from the nonvolatile memory (RECALL operation). Both STORE and RECALL operations can also be initiated by the user through SPI instruction. Configuration Feature Write protection ❐ Hardware protection using Write Protect (WP) pin ❐ Software protection using Write Disable instruction ❐ Software block protection for 1/4,1/2, or entire array ■ Low power consumption ❐ Single 3 V +20%, –10% operation ❐ Average active current of 10 mA at 40 MHz operation ■ Industry standard configurations ❐ Industrial temperature ❐ CY14B101Q1 has identical pin configuration to industry standard 8-pin NV memory CY14B101Q1 CY14B101Q2 CY14B101Q3 AutoStore No Yes Yes Software STORE Yes Yes Yes Hardware STORE No No Yes Logic Block Diagram VCC CS WP SCK QuantumTrap 128 K X 8 Instruction decode Write protect Control logic STORE SRAM Array HOLD RECALL 128 K X 8 Instruction register Address Decoder SI VCAP Power Control STORE/RECALL Control HSB D0-D7 A0-A16 Data I/O register SO Status Register Cypress Semiconductor Corporation Document #: 001-50091 Rev. *H • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised January 18, 2011 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Contents Pinouts .............................................................................. 3 Device Operation .............................................................. 4 SRAM Write................................................................. 4 SRAM Read ................................................................ 4 STORE Operation ....................................................... 4 AutoStore Operation .................................................... 5 Software STORE Operation ........................................ 5 Hardware STORE and HSB Pin Operation ................. 5 RECALL Operation...................................................... 5 Hardware RECALL (Power-Up) .................................. 5 Software RECALL ........................................................ 5 Disabling and Enabling AutoStore............................... 6 Noise Considerations ....................................................... 6 Serial Peripheral Interface ............................................... 6 SPI Overview............................................................... 6 SPI Modes................................................................... 7 SPI Operating Features .................................................... 8 Power-Up .................................................................... 8 Power On Reset .......................................................... 8 Power-Down ................................................................ 8 Active Power and Standby Power Modes ................... 8 SPI Functional Description .............................................. 8 Status Register ................................................................. 9 Read Status Register (RDSR) Instruction ................... 9 Write Status Register (WRSR) Instruction .................. 9 Write Protection and Block Protection ......................... 10 Write Enable (WREN) Instruction .............................. 10 Write Disable (WRDI) Instruction .............................. 10 Block Protection ........................................................ 10 Write Protect (WP) Pin .............................................. 11 Memory Access .............................................................. 11 Document #: 001-50091 Rev. *H Read Sequence (READ) instruction .......................... 11 Write Sequence (WRITE) instruction ........................ 11 Software STORE (STORE) instruction ...................... 13 Software RECALL (RECALL) instruction .................. 13 AutoStore Enable (ASENB) instruction ..................... 13 AutoStore Disable (ASDISB) instruction ................... 13 HOLD Pin Operation ................................................. 14 Best Practices ................................................................. 14 Maximum Ratings........................................................... 15 DC Electrical Characteristics ........................................ 15 Data Retention and Endurance ..................................... 16 Capacitance .................................................................... 16 Thermal Resistance........................................................ 16 AC Test Conditions ........................................................ 16 AC Switching Characteristics ....................................... 17 AutoStore or Power-Up RECALL .................................. 18 Software Controlled STORE and RECALL Cycles ...... 19 Hardware STORE Cycle ................................................. 20 Ordering Information ...................................................... 21 Ordering Code Definition ........................................... 21 Package Diagrams........................................................... 22 Acronyms ........................................................................ 24 Document Conventions ................................................. 24 Units of Measure ....................................................... 24 Document History Page ................................................ 25 Sales, Solutions, and Legal Information ...................... 26 Worldwide Sales and Design Support ....................... 26 Products .................................................................... 26 PSoC Solutions ......................................................... 26 Page 2 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Pinouts Figure 1. Pin Diagram - 8-Pin DFN[1, 2, 3] CY14B101Q1 CS CY14B101Q2 O SO 1 2 WP 3 VSS 4 EXPOSED PAD O 8 VCC CS 7 HOLD SO 6 SCK 5 SI 1 2 VCAP 3 VSS 4 Top View (not to scale) EXPOSED PAD 8 VCC 7 HOLD 6 SCK 5 SI Top View (not to scale) Figure 2. Pin Diagram - 16-Pin SOIC NC 1 16 VCC NC 2 15 NC NC 3 14 VCAP 13 SO 12 SI CY14B101Q3 NC 4 WP 5 HOLD 6 11 SCK NC 7 10 CS VSS 8 9 Top View not to scale HSB Table 1. Pin Definitions Pin Name CS I/O Type Input SCK Input SI SO WP HOLD HSB Input Output Input Input Input/Output VCAP Power supply NC VSS VCC EXPOSED PAD No connect Power supply Power supply No connect Description Chip select. Activates the device when pulled LOW. Driving this pin high puts the device in low power standby mode. Serial clock. Runs at speeds up to maximum of fSCK. Serial input is latched at the rising edge of this clock. Serial output is driven at the falling edge of the clock. Serial input. Pin for input of all SPI instructions and data. Serial output. Pin for output of data through SPI. Write protect. Implements hardware write protection in SPI. HOLD pin. suspends serial operation. Output: Indicates busy status of nvSRAM when LOW. After each Hardware and Software STORE operation HSB is driven HIGH for a short time (tHHHD) with standard output high current and then weak internal pull up resistor keeps this pin HIGH (External pull up resistor connection optional). Input: Hardware STORE implemented by pulling this pin LOW externally. AutoStore capacitor. Supplies power to the nvSRAM during power loss to STORE data from the SRAM to nonvolatile elements. If AutoStore is not needed, this pin must be left as No connect. It must never be connected to VSS. No connect: This pin is not connected to the die. Ground Power supply (2.7 V to 3.6 V) The EXPOSED PAD on the bottom of 8-pin DFN package is not connected to the die. It is recommended to connect the EXPOSED PAD to VSS. Thermal vias can be used to increase thermal conductivity. Notes 1. HSB pin is not available in 8 DFN packages. 2. CY14B101Q1 part does not have VCAP pin and does not support AutoStore. 3. CY14B101Q2 part does not have WP pin Document #: 001-50091 Rev. *H Page 3 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Device Operation SRAM Write CY14B101Q1/CY14B101Q2/CY14B101Q3 is a 1 Mbit nvSRAM memory with a nonvolatile element in each memory cell. All the reads and writes to nvSRAM happen to the SRAM which gives nvSRAM the unique capability to handle infinite writes to the memory. The data in SRAM is secured by a STORE sequence which transfers the data in parallel to the nonvolatile QuantumTrap cells. A small capacitor (VCAP) is used to AutoStore the SRAM data in nonvolatile cells when power goes down providing power-down data security. The QuantumTrap nonvolatile elements built in the reliable SONOS technology make nvSRAM the ideal choice for secure data storage. All writes to nvSRAM are carried out on the SRAM and do not use up any endurance cycles of the nonvolatile memory. This enables the user to perform infinite write operations. A write cycle is performed through the WRITE instruction. The WRITE instruction is issued through the SI pin of the nvSRAM and consists of the WRITE opcode, three bytes of address, and one byte of data. Write to nvSRAM is done at SPI bus speed with zero cycle delay. The 1 Mbit memory array is organized as 128 K words x 8 bits. The memory is accessed through a standard SPI interface that enables very high clock speeds up to 40 MHz with zero cycle delay read and write cycles. This device supports SPI modes 0 and 3 (CPOL, CPHA = 0, 0 and 1, 1) and operates as SPI slave. The device is enabled using the Chip Select (CS) pin and accessed through Serial Input (SI), Serial Output (SO), and Serial Clock (SCK) pins. This device provides the feature for hardware and software write protection through the WP pin and WRDI instruction respectively along with mechanisms for block write protection (1/4, 1/2, or full array) using BP0 and BP1 pins in the status register. Further, the HOLD pin can be used to suspend any serial communication without resetting the serial sequence. CY14B101Q1/CY14B101Q2/CY14B101Q3 uses the standard SPI opcodes for memory access. In addition to the general SPI instructions for read and write, it provides four special instructions which enable access to four nvSRAM specific functions: STORE, RECALL, AutoStore Disable (ASDISB), and AutoStore Enable (ASENB). The major benefit of serial (SPI) nvSRAM over serial EEPROMs is that all reads and writes to nvSRAM are performed at the speed of SPI bus with zero cycle delay. Therefore, no wait time is required after any of the memory accesses. The STORE and RECALL operations need finite time to complete and all memory accesses are inhibited during this time. While a STORE or RECALL operation is in progress, the busy status of the device is indicated by the Hardware STORE Busy (HSB) pin and also reflected on the RDY bit of the Status Register. The device is available in three different pin configurations that enable the user to choose a part which fits in best in their application. The feature summary is given in Table 2. Table 2. Feature Summary Feature CY14B101Q1 CY14B101Q2 CY14B101Q3 WP Yes No Yes VCAP No Yes Yes HSB No No Yes AutoStore No Yes Yes Power Up RECALL Yes Yes Yes Hardware STORE No No Yes Software STORE Yes Yes Yes Document #: 001-50091 Rev. *H The device allows burst mode writes to be performed through SPI. This enables write operations on consecutive addresses without issuing a new WRITE instruction. When the last address in memory is reached in burst mode, the address rolls over to 0x0000 and the device continues to write. The SPI write cycle sequence is defined in the memory access section of SPI Protocol Description. SRAM Read A read cycle is performed at the SPI bus speed and the data is read out with zero cycle delay after the READ instruction is executed. The READ instruction is issued through the SI pin of the nvSRAM and consists of the READ opcode and 3 bytes of address. The data is read out on the SO pin. This device allows burst mode reads to be performed through SPI. This enables reads on consecutive addresses without issuing a new READ instruction. When the last address in memory is reached in burst mode read, the address rolls over to 0x0000 and the device continues to read. The SPI read cycle sequence is defined in the memory access section of SPI Protocol Description. STORE Operation STORE operation transfers the data from the SRAM to the nonvolatile QuantumTrap cells. The device stores data to the nonvolatile cells using one of the three STORE operations: AutoStore, activated on device power-down; Software STORE, activated by a STORE instruction; and Hardware STORE, activated by the HSB. During the STORE cycle, an erase of the previous nonvolatile data is first performed, followed by a program of the nonvolatile elements. After a STORE cycle is initiated, read/write to CY14B101Q1/CY14B101Q2/CY14B101Q3 is inhibited until the cycle is completed The HSB signal or the RDY bit in the Status register can be monitored by the system to detect if a STORE or Software RECALL cycle is in progress. The busy status of nvSRAM is indicated by HSB being pulled LOW or RDY bit being set to ‘1’. To avoid unnecessary nonvolatile STOREs, AutoStore and Hardware STORE operations are ignored unless at least one write operation has taken place since the most recent STORE or RECALL cycle. However, software initiated STORE cycles are performed regardless of whether a write operation has taken place. Page 4 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 The AutoStore operation is a unique feature of nvSRAM which automatically stores the SRAM data to QuantumTrap during power-down. This STORE makes use of an external capacitor (VCAP) and enables the device to safely STORE the data in the nonvolatile memory when power goes down. During normal operation, the device draws current from VCC to charge the capacitor connected to the VCAP pin. When the voltage on the VCC pin drops below VSWITCH during power-down, the device inhibits all memory accesses to nvSRAM and automatically performs a conditional STORE operation using the charge from the VCAP capacitor. The AutoStore operation is not initiated if no write cycle has been performed since the last RECALL. Note If a capacitor is not connected to VCAP pin, AutoStore must be disabled by issuing the AutoStore Disable instruction specified in AutoStore Disable (ASDISB) instruction on page 13. If AutoStore is enabled without a capacitor on the VCAP pin, the device attempts an AutoStore operation without sufficient charge to complete the STORE. This corrupts the data stored in the nvSRAM and Status register. To resume normal functionality, the WRSR instruction must be issued to update the nonvolatile bits BP0, BP1 and WPEN in the Status Register. Figure 3 shows the proper connection of the storage capacitor (VCAP) for AutoStore operation. Refer to DC Electrical Characteristics on page 15 for the size of the VCAP. Note For successfull last data byte STORE, a hardware store should be initiated atleast one clock cycle after the last data bit D0 is recieved. Upon completion of the STORE operation, the nvSRAM memory access is inhibited for tLZHSB time after HSB pin returns HIGH. The HSB pin must be left unconnected if not used. Note CY14B101Q1/CY14B101Q2 do not have HSB pin. RDY bit of the SPI status register may be probed to determine the Ready or Busy status of nvSRAM Figure 3. AutoStore Mode VCC 0.1 uF 10 kOhm AutoStore Operation VCC CS VCAP VSS VCAP Note CY14B101Q1 does not support AutoStore operation. The user must perform Software STORE operation by using the SPI STORE instruction to secure the data. Software STORE Operation RECALL Operation Software STORE enables the user to trigger a STORE operation through a special SPI instruction. STORE operation is initiated by executing STORE instruction irrespective of whether a write has been performed since the last NV operation. A RECALL operation transfers the data stored in the nonvolatile QuantumTrap elements to the SRAM. A RECALL may be initiated in two ways: Hardware RECALL, initiated on power-up; and Software RECALL, initiated by a SPI RECALL instruction. A STORE cycle takes tSTORE time to complete, during which all the memory accesses to nvSRAM are inhibited. The RDY bit of the Status register or the HSB pin may be polled to find the Ready or Busy status of the nvSRAM. After the tSTORE cycle time is completed, the SRAM is activated again for read and write operations. Internally, RECALL is a two-step procedure. First, the SRAM data is cleared. Next, the nonvolatile information is transferred into the SRAM cells. All memory accesses are inhibited while a RECALL cycle is in progress. The RECALL operation does not alter the data in the nonvolatile elements. Hardware STORE and HSB Pin Operation During power-up, when VCC crosses VSWITCH, an automatic RECALL sequence is initiated which transfers the content of nonvolatile memory on to the SRAM. The data would previously have been stored on the nonvolatile memory through a STORE sequence. The HSB pin in CY14B101Q3 is used to control and acknowledge STORE operations. If no STORE or RECALL is in progress, this pin can be used to request a Hardware STORE cycle. When the HSB pin is driven LOW, nvSRAM conditionally initiates a STORE operation after tDELAY duration. An actual STORE cycle starts only if a write to the SRAM has been performed since the last STORE or RECALL cycle. Reads and writes to the memory are inhibited for tSTORE duration or as long as HSB pin is LOW. Hardware RECALL (Power-Up) A Power-Up RECALL cycle takes tFA time to complete and the memory access is disabled during this time. HSB pin is used to detect the Ready status of the device. Software RECALL The HSB pin also acts as an open drain driver (internal 100 kΩ weak pull-up resistor) that is internally driven LOW to indicate a busy condition when the STORE (initiated by any means) is in progress. Software RECALL enables the user to initiate a RECALL operation to restore the content of nonvolatile memory on to the SRAM. A Software RECALL is issued by using the SPI instruction for RECALL. Note After each Hardware and Software STORE operation HSB is driven HIGH for a short time (tHHHD) with standard output high current and then remains HIGH by an internal 100 kΩ pull-up resistor. A Software RECALL takes tRECALL time to complete during which all memory accesses to nvSRAM are inhibited. The controller must provide sufficient delay for the RECALL operation to complete before issuing any memory access instructions. Document #: 001-50091 Rev. *H Page 5 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Disabling and Enabling AutoStore If the application does not require the AutoStore feature, it can be disabled by using the ASDISB instruction. If this is done, the nvSRAM does not perform a STORE operation at power-down. AutoStore can be re-enabled by using the ASENB instruction. However, these operations are not nonvolatile and if the user need this setting to survive the power cycle, a STORE operation must be performed following AutoStore Disable or Enable operation. Note CY14B101Q2/CY14B101Q3 has AutoStore Enabled from the factory. In CY14B101Q1, VCAP pin is not present and AutoStore option is not available. The AutoStore Enable and Disable instructions to CY14B101Q1 are ignored. Note If AutoStore is disabled and VCAP is not required, then the VCAP pin must be left open. VCAP pin must never be connected to ground. Power-Up RECALL operation cannot be disabled in any case. SPI Slave The SPI slave device is activated by the master through the chip select line. A slave device gets the SCK as an input from the SPI master and all the communication is synchronized with this clock. SPI slave never initiates a communication on the SPI bus and acts on the instruction from the master. CY14B101Q1/CY14B101Q2/CY14B101Q3 operates as a SPI slave and may share the SPI bus with other SPI slave devices. Chip Select (CS) For selecting any slave device, the master needs to pull-down the corresponding CS pin. Any instruction can be issued to a slave device only while the CS pin is LOW. When the device is not selected, data through the SI pin is ignored and the serial output pin (SO) remains in a high-impedance state. Note A new instruction must begin with the falling edge of CS. Therefore, only one opcode can be issued for each active chip select cycle. Noise Considerations Serial Clock (SCK) Refer to CY application note AN1064. Serial clock is generated by the SPI master and the communication is synchronized with this clock after CS goes LOW. Serial Peripheral Interface SPI Overview The SPI is a four-pin interface with Chip Select (CS), Serial Input (SI), Serial Output (SO) and Serial Clock (SCK) pins. CY14B101Q1/CY14B101Q2/CY14B101Q3 provides serial access to nvSRAM through SPI interface. The SPI bus on this device can run at speeds up to 40 MHz. The SPI is a synchronous serial interface which uses clock and data pins for memory access and supports multiple devices on the data bus. A device on SPI bus is activated using a CS pin. The relationship between chip select, clock, and data is dictated by the SPI mode. This device supports SPI modes 0 and 3. In both these modes, data is clocked into the nvSRAM on the rising edge of SCK starting from the first rising edge after CS goes active. The SPI protocol is controlled by opcodes. These opcodes specify the commands from the bus master to the slave device. After CS is activated the first byte transferred from the bus master is the opcode. Following the opcode, any addresses and data are then transferred. The CS must go inactive after an operation is complete and before a new opcode can be issued. The commonly used terms used in SPI protocol are as follows: SPI Master The SPI master device controls the operations on a SPI bus. A SPI bus may have only one master with one or more slave devices. All the slaves share the same SPI bus lines and the master may select any of the slave devices using the CS pin. All the operations must be initiated by the master activating a slave device by pulling the CS pin of the slave LOW. The master also generates the SCK and all the data transmission on SI and SO lines are synchronized with this clock. Document #: 001-50091 Rev. *H CY14B101Q1/CY14B101Q2/CY14B101Q3 enables SPI modes 0 and 3 for data communication. In both these modes, the inputs are latched by the slave device on the rising edge of SCK and outputs are issued on the falling edge. Therefore, the first rising edge of SCK signifies the arrival of the first bit (MSB) of SPI instruction on the SI pin. Further, all data inputs and outputs are synchronized with SCK. Data Transmission - SI and SO SPI data bus consists of two lines, SI and SO, for serial data communication. The SI is also referred to as Master Out Slave In (MOSI) and SO is referred to as Master In Slave Out (MISO). The master issues instructions to the slave through the SI pin, while the slave responds through the SO pin. Multiple slave devices may share the SI and SO lines as described earlier. Most Significant Bit (MSB) The SPI protocol requires that the first bit to be transmitted is the most significant bit (MSB). This is valid for both address and data transmission. The 1 Mbit serial nvSRAM requires a 3-byte address for any read or write operation. However, since the actual address is only 17 bits, it implies that the first seven bits which are fed in are ignored by the device. Although these seven bits are ‘don’t care’, Cypress recommends that these bits are treated as 0s to enable seamless transition to higher memory densities. Serial Opcode After the slave device is selected with CS going LOW, the first byte received is treated as the opcode for the intended operation. CY14B101Q1/CY14B101Q2/CY14B101Q3 uses the standard opcodes for memory accesses. In addition to the memory accesses, it provides additional opcodes for the nvSRAM specific functions: STORE, RECALL, AutoStore Enable, and AutoStore Disable. Refer to Table 3 on page 8 for details. Page 6 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Invalid Opcode Status Register If an invalid opcode is received, the opcode is ignored and the CY14B101Q1/CY14B101Q2/CY14B101Q3 has an 8-bit status device ignores any additional serial data on the SI pin till the next register. The bits in the status register are used to configure the falling edge of CS and the SO pin remains tristated. SPI bus. These bits are described in the Table 5 on page 9. Figure 4. System Configuration Using SPI nvSRAM SCK M OSI M IS O SCK SI SO SCK SI SO u C o n tro lle r C Y14B 101Q x CS C Y14B 101Q x HO LD CS HO LD CS1 HO LD 1 CS2 HO LD 2 SPI Modes CY14B101Q1/CY14B101Q2/CY14B101Q3 may be driven by a microcontroller with its SPI peripheral running in either of the following two modes: The two SPI modes are shown in Figure 5 and Figure 6. The status of clock when the bus master is in standby mode and not transferring data is: ■ SCK remains at 0 for Mode 0 SCK remains at 1 for Mode 3 ■ SPI Mode 0 (CPOL=0, CPHA=0) ■ ■ SPI Mode 3 (CPOL=1, CPHA=1) CPOL and CPHA bits must be set in the SPI controller for the either Mode 0 or Mode 3. The device detects the SPI mode from the status of SCK pin when the device is selected by bringing the CS pin LOW. If SCK pin is LOW when the device is selected, SPI Mode 0 is assumed and if SCK pin is HIGH, it works in SPI Mode 3. For both these modes, the input data is latched-in on the rising edge of SCK starting from the first rising edge after CS goes active. If the clock starts from a HIGH state (in mode 3), the first rising edge, after the clock toggles, is considered. The output data is available on the falling edge of SCK. Figure 6. SPI Mode 3 Figure 5. SPI Mode 0 CS CS 0 1 2 3 4 5 6 1 2 3 4 5 6 7 SCK SCK SI 0 7 7 6 5 4 MSB Document #: 001-50091 Rev. *H 3 2 1 0 LSB SI 7 MSB 6 5 4 3 2 1 0 LSB Page 7 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 SPI Operating Features Active Power and Standby Power Modes Power-Up When CS is LOW, the device is selected, and is in the active power mode. The device consumes ICC current, as specified in DC Electrical Characteristics on page 15. When CS is HIGH, the device is deselected and the device goes into the standby power mode if a STORE or RECALL cycle is not in progress. If a STORE or RECALL cycle is in progress, the device goes into the standby power mode after the STORE or RECALL cycle is completed. In the standby power mode, the current drawn by the device drops to ISB. Power-up is defined as the condition when the power supply is turned on and VCC crosses Vswitch voltage. During this time, the CS must be allowed to follow the VCC voltage. Therefore, CS must be connected to VCC through a suitable pull-up resistor. As a built-in safety feature, CS is both edge sensitive and level sensitive. After power-up, the device is not selected until a falling edge is detected on CS. This ensures that CS is HIGH, before going LOW to start the first operation. As described earlier, nvSRAM performs a Power-Up RECALL operation after power-up and therefore, all memory accesses are disabled for tFA duration after power-up. The HSB pin can be probed to check the ready or busy status of nvSRAM after power-up. Power On Reset A power on reset (POR) circuit is included to prevent inadvertent writes. At power-up, the device does not respond to any instruction until the VCC reaches the POR threshold voltage (VSWITCH). After VCC transitions the POR threshold, the device is internally reset and performs an Power-Up RECALL operation. During Power-Up RECALL all device accesses are inhibited. The device is in the following state after POR: ■ Deselected (after power-up, a falling edge is required on CS before any instructions are started). ■ Standby power mode ■ Not in the HOLD condition Status register state: ❐ Write Enable (WEN) bit is reset to 0. ❐ WPEN, BP1, BP0 unchanged from previous STORE operation ❐ Don’t care bits 4-6 are reset to 0. The WPEN, BP1, and BP0 bits of the Status Register are nonvolatile bits and remain unchanged from the previous STORE operation. SPI Functional Description The CY14B101Q1/CY14B101Q2/CY14B101Q3 uses an 8-bit instruction register. Instructions and their operation codes are listed in Table 3. All instructions, addresses, and data are transferred with the MSB first and start with a HIGH to LOW CS transition. There are, in all, 10 SPI instructions which provide access to most of the functions in nvSRAM. Further, the WP, HOLD and HSB pins provide additional functionality driven through hardware. Table 3. Instruction Set Instruction Category Status Register Control Instructions Instruction Name Opcode Operation WREN 0000 0110 Set write enable latch WRDI 0000 0100 Reset write enable latch RDSR 0000 0101 Read Status Register WRSR 0000 0001 Write Status Register READ 0000 0011 Read data from memory array WRITE 0000 0010 Write data to memory array ■ Before selecting and issuing instructions to the memory, a valid and stable VCC voltage must be applied. This voltage must remain valid until the end of the instruction transmission. SRAM Read/Write Instructions Special NV Instructions Power-Down At power-down (continuous decay of VCC), when VCC drops from the normal operating voltage and below the VSWITCH threshold voltage, the device stops responding to any instruction sent to it. If a write cycle is in progress and the last data bit D0 has been received when the power goes down, it is allowed tDELAY time to complete the write. After which all memory accesses are inhibited and a conditional AutoStore operation is performed (AutoStore is not performed if no writes have happened since last RECALL cycle). This feature prevents inadvertent writes to nvSRAM from happening during power-down. However, to completely avoid the possibility of inadvertent writes during power-down, ensure that the device is deselected and is in standby power mode, and the CS follows the voltage applied on VCC. Document #: 001-50091 Rev. *H Reserved STORE 0011 1100 Software STORE RECALL 0110 0000 ASENB 0101 1001 AutoStore Enable ASDISB 0001 1001 AutoStore Disable Software RECALL - Reserved - 0001 1110 The SPI instructions are divided based on their functionality in the following types: ❐ Status Register access: RDSR and WRSR instructions ❐ Write protection functions: WREN and WRDI instructions along with WP pin and WEN, BP0, and BP1 bits ❐ SRAM memory access: READ and WRITE instructions ❐ nvSRAM special instructions: STORE, RECALL, ASENB, and ASDISB Page 8 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Status Register The status register bits are listed in Table 4. The status register consists of a Ready bit (RDY) and data protection bits BP1, BP0, WEN, and WPEN. The RDY bit can be polled to check the Ready or Busy status while a nvSRAM STORE or Software RECALL cycle is in progress. The status register can be modified by WRSR instruction and read by RDSR instruction. However, only the WPEN, BP1, and BP0 bits of the Status Register can be modified by using WRSR instruction. The WRSR instruction has no effect on WEN and RDY bits. The default value shipped from the factory for WEN, BP0, BP1, bits 4-6 and WPEN bits is ‘0’. Table 4. Status Register Format Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 WPEN (0) X (0) X (0) X (0) BP1 (0) BP0 (0) WEN (0) RDY Table 5. Status Register Bit Definition Definition Description Bit 0 (RDY) Bit Ready Read only bit indicates the ready status of device to perform a memory access. This bit is set to ‘1’ by the device while a STORE or Software RECALL cycle is in progress. Bit 1 (WEN) Write Enable WEN indicates if the device is Write Enabled. This bit defaults to ‘0’ (disabled) on power-up. WEN = '1' --> Write Enabled WEN = '0' --> Write Disabled Bit 2 (BP0) Block protect bit ‘0’ Bit 3 (BP1) Block protect bit ‘1’ Bits 4-6 Bit 7 (WPEN) Used for block protection. For details see Table 6 on page 10. Used for block protection. For details see Table 6 on page 10. Don’t care Bits are writable and volatile. On power-up, bits are written with ‘0’. Write protect enable bit Used for enabling the function of Write Protect Pin (WP). For details see Table 7 on page 11. Read Status Register (RDSR) Instruction WRSR instruction is a write instruction and needs writes to be enabled (WEN bit set to ‘1’) using the WREN instruction before it is issued. The instruction is issued after the falling edge of CS using the opcode for WRSR followed by 8 bits of data to be stored in the Status Register. Since only bits 2, 3, and 7 can be modified by WRSR instruction; therefore, it is recommended to leave the bits 4-6 as ‘0’ while writing to the Status Register The Read Status Register instruction provides access to the status register. This instruction is used to probe the Write Enable Status of the device or the Ready status of the device. RDY bit is set by the device to ‘1’ whenever a STORE or Software RECALL cycle is in progress. The block protection and WPEN bits indicate the extent of protection employed. Note In CY14B101Q1/CY14B101Q2/CY14B101Q3, the values written to Status Register are saved to nonvolatile memory only after a STORE operation. If AutoStore is disabled (or while using CY14B101Q1), any modifications to the Status Register must be secured by performing a Software STORE operation. This instruction is issued after the falling edge of CS using the opcode for RDSR. Write Status Register (WRSR) Instruction The WRSR instruction enables the user to write to the Status register. However, this instruction cannot be used to modify bit 0 and bit 1 (RDY and WEN). The BP0 and BP1 bits can be used to select one of four levels of block protection. Further, WPEN bit must be set to ‘1’ to enable the use of write protect (WP) pin. Note CY14B101Q2 does not have WP pin. Any modification to bit 7 of the Status register has no effect on the functionality of CY14B101Q2. Figure 7. Read Status Register (RDSR) Instruction Timing CS 0 1 2 3 4 5 6 7 0 1 0 MSB 1 2 3 4 5 6 7 SCK SI SO 0 0 0 0 HI-Z 0 1 0 D7 D6 D5 D4 D3 D2 D1 D0 MSB Document #: 001-50091 Rev. *H LSB Data LSB Page 9 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Figure 8. Write Status Register (WRSR) Instruction Timing CS 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCK Data in Opcode SI 0 0 0 0 0 0 0 1 D7 X MSB X X D3 D2 X X LSB HI-Z SO Write Protection and Block Protection Write Disable (WRDI) Instruction CY14B101Q1/CY14B101Q2/CY14B101Q3 provides features for both software and hardware write protection using WRDI instruction and WP. Additionally, this device also provides block protection mechanism through BP0 and BP1 pins of the Status Register. Write Disable instruction disables the write by clearing the WEN bit to ‘0’ in order to protect the device against inadvertent writes. This instruction is issued following the falling edge of CS followed by opcode for WRDI instruction. The WEN bit is cleared on the rising edge of CS following a WRDI instruction. Figure 10. WRDI Instruction The write enable and disable status of the device is indicated by WEN bit of the status register. The write instructions (WRSR and WRITE) and nvSRAM special instruction (STORE, RECALL, ASENB, and ASDISB) need the write to be enabled (WEN bit = 1) before they can be issued. Write Enable (WREN) Instruction On power-up, the device is always in the write disable state. The following WRITE, WRSR, or nvSRAM special instruction must therefore be preceded by a Write Enable instruction. If the device is not write enabled (WEN = ‘0’), it ignores the write instructions and returns to the standby state when CS is brought HIGH. A new CS falling edge is required to re-initiate serial communication. The instruction is issued following the falling edge of CS. When this instruction is used, the WEN bit of status register is set to ‘1’. WEN bit defaults to ‘0’ on power-up. Note After completion of a write instruction (WRSR or WRITE) or nvSRAM special instruction (STORE, RECALL, ASENB, and ASDISB) instruction, WEN bit is cleared to ‘0’. This is done to provide protection from any inadvertent writes. Therefore, WREN instruction must be used before a new write instruction is issued. Figure 9. WREN Instruction 0 1 2 3 4 5 6 7 SCK SO 0 0 0 0 0 0 1 1 0 1 2 3 4 5 6 7 SCK SI 0 0 0 0 0 1 0 0 HI-Z SO Block Protection Block protection is provided using the BP0 and BP1 pins of the Status register. These bits can be set using WRSR instruction and probed using the RDSR instruction. The nvSRAM is divided into four array segments. One-quarter, one-half, or all of the memory segments can be protected. Any data within the protected segment is read only. Table 6 shows the function of block protect bits. Table 6. Block Write Protect Bits Level CS SI CS Status Register Bits BP1 Array Addresses Protected BP0 0 0 0 None 1 (1/4) 0 1 0x18000-0x1FFFF 2 (1/2) 1 0 0x10000-0x1FFFF 3 (All) 1 1 0x00000-0x1FFFF HI-Z Document #: 001-50091 Rev. *H Page 10 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Write Protect (WP) Pin address. The Most Significant address byte contains A16 in bit 0 and other bits as ‘don’t cares’. Address bits A15 to A0 are sent in the following two address bytes. After the last address bit is transmitted on the SI pin, the data (D7-D0) at the specific address is shifted out on the SO line on the falling edge of SCK starting with D7. Any other data on SI line after the last address bit is ignored. The write protect pin (WP) is used to provide hardware write protection. WP pin enables all normal read and write operations when held HIGH. When the WP pin is brought LOW and WPEN bit is ‘1’, all write operations to the status register are inhibited. The hardware write protection function is blocked when the WPEN bit is ‘0’. This enables the user to install the device in a system with the WP pin tied to ground, and still write to the status register. CY14B101Q1/CY14B101Q2/CY14B101Q3 allows reads to be performed in bursts through SPI which can be used to read consecutive addresses without issuing a new READ instruction. If only one byte is to be read, the CS line must be driven HIGH after one byte of data comes out. However, the read sequence may be continued by holding the CS line LOW and the address is automatically incremented and data continues to shift out on SO pin. When the last data memory address (0x1FFFF) is reached, the address rolls over to 0x0000 and the device continues to read. WP pin can be used along with WPEN and block protect bits (BP1 and BP0) of the status register to inhibit writes to memory. When WP pin is LOW and WPEN is set to ‘1’, any modifications to status register are disabled. Therefore, the memory is protected by setting the BP0 and BP1 bits and the WP pin inhibits any modification of the status register bits, providing hardware write protection. Note WP going LOW when CS is still LOW has no effect on any of the ongoing write operations to the status register. Write Sequence (WRITE) instruction The write operations on this device are performed through the SI pin. To perform a write operation, if the device is write disabled, then the device must first be write enabled through the WREN instruction. When the writes are enabled (WEN = ‘1’), WRITE instruction is issued after the falling edge of CS. A WRITE instruction constitutes transmitting the WRITE opcode on SI line followed by 3 bytes of address and the data (D7-D0) which is to be written. The Most Significant address byte contains A16 in bit 0 with other bits being ‘don’t cares’. Address bits A15 to A0 are sent in the following two address bytes. Note CY14B101Q2 does not have WP pin and therefore does not provide hardware write protection. Table 7 summarizes all the protection features of this device Table 7. Write Protection Operation Unprotected WEN Protected Blocks Blocks Status Register WPEN WP X X 0 Protected Protected 0 X 1 Protected Writable Writable 1 LOW 1 Protected Writable Protected 1 HIGH 1 Protected Writable Writable Protected CY14B101Q1/CY14B101Q2/CY14B101Q3 enables writes to be performed in bursts through SPI which can be used to write consecutive addresses without issuing a new WRITE instruction. If only one byte is to be written, the CS line must be driven HIGH after the D0 (LSB of data) is transmitted. However, if more bytes are to be written, CS line must be held LOW and address is incremented automatically. The following bytes on the SI line are treated as data bytes and written in the successive addresses. When the last data memory address (0x1FFFF) is reached, the address rolls over to 0x0000 and the device continues to write. The WEN bit is reset to ‘0’ on completion of a WRITE sequence. Memory Access All memory accesses are done using the READ and WRITE instructions. These instructions cannot be used while a STORE or RECALL cycle is in progress. A STORE cycle in progress is indicated by the RDY bit of the status register and the HSB pin. Read Sequence (READ) instruction Note When a burst write reaches a protected block address, it continues the address increment into the protected space but does not write any data to the protected memory. If the address roll over takes the burst write to unprotected space, it resumes writes. The same operation is true if a burst write is initiated within a write protected block. The read operations on this device are performed by giving the instruction on SI and reading the output on SO pin. The following sequence needs to be followed for a read operation: After the CS line is pulled LOW to select a device, the read opcode is transmitted through the SI line followed by three bytes of Figure 11. Read Instruction Timing CS 1 2 3 4 5 6 7 0 1 2 3 4 5 Op-Code SI 0 0 0 0 0 SO 0 6 7 ~ ~ ~ ~ 0 SCK 20 21 22 23 0 1 2 3 4 5 6 7 17-bit Address 1 1 0 0 MSB 0 0 0 0 0 A16 A3 A2 A1 A0 LSB D7 D6 D5 D4 D3 D2 D1 D0 LSB Data MSB Document #: 001-50091 Rev. *H Page 11 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Figure 12. Burst Mode Read Instruction Timing CS 2 3 4 5 6 7 0 1 2 3 4 5 6 7 Op-Code 0 0 0 0 1 2 3 4 5 6 7 0 0 7 1 2 3 4 5 6 7 17-bit Address 0 1 0 1 0 0 0 0 0 0 ~ ~ SI 20 21 22 23 0 ~ ~ 1 ~ ~ 0 SCK A16 0 MSB A3 A2 A1 A0 LSB Data Byte N ~ ~ Data Byte 1 SO D7 D6 D5 D4 D3 D2 D1 D0 D7 D0 D7 D6 D5 D4 D3 D2 D1 D0 MSB MSB LSB LSB Figure 13. Write Instruction Timing CS 1 2 3 4 5 0 7 6 1 2 3 4 5 6 7 ~ ~ ~ ~ 0 SCK Op-Code SI 0 0 0 0 0 20 21 22 23 0 1 2 3 4 5 6 7 17-bit Address 0 1 0 0 0 0 0 0 0 0 A16 MSB A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 LSB MSB LSB Data HI-Z SO Figure 14. Burst Mode Write Instruction Timing CS 2 3 4 5 6 7 0 1 2 3 4 5 6 7 20 21 22 23 0 1 2 3 4 5 6 7 0 0 0 17-bit Address 0 1 0 0 0 0 0 0 0 0 ~ ~ SI 0 A16 Document #: 001-50091 Rev. *H 2 3 4 5 6 7 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D0 D7 D6 D5 D4 D3 D2 D1 D0 LSB MSB MSB SO 1 ~ ~ Op-Code 0 0 Data Byte N Data Byte 1 0 7 ~ ~ 1 ~ ~ 0 SCK LSB HI-Z Page 12 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 nvSRAM Special Instructions AutoStore Enable (ASENB) instruction CY14B101Q1/CY14B101Q2/CY14B101Q3 provides four special instructions which enables access to the nvSRAM specific functions: STORE, RECALL, ASDISB, and ASENB. Table 8 lists these instructions. The AutoStore Enable instruction enables the AutoStore on CY14B101Q1. This setting is not nonvolatile and needs to be followed by a STORE sequenceif this is desired to survive the power cycle. Table 8. nvSRAM Special Instructions To issue this instruction, the device must be write enabled (WEN = ‘1’). The instruction is performed by transmitting the ASENB opcode on the SI pin following the falling edge of CS. The WEN bit is cleared on the positive edge of CS following the ASENB instruction. Function Name STORE RECALL ASENB ASDISB Opcode 0011 1100 0110 0000 0101 1001 0001 1001 Operation Software STORE Software RECALL AutoStore Enable AutoStore Disable Software STORE (STORE) instruction When a STORE instruction is executed, nvSRAM performs a Software STORE operation. The STORE operation is performed irrespective of whether a write has taken place since the last STORE or RECALL operation. To issue this instruction, the device must be write enabled (WEN bit = ‘1’). The instruction is performed by transmitting the STORE opcode on the SI pin following the falling edge of CS. The WEN bit is cleared on the positive edge of CS following the STORE instruction. Figure 15. Software STORE Operation Note If ASDISB and ASENB instructions are executed in CY14B101Q1, the device is busy for the duration of software sequence processing time (tSS). However, ASDISB and ASENB instructions have no effect on CY14B101Q1 as AutoStore is internally disabled. Figure 17. AutoStore Enable Operation CS 0 1 2 3 4 5 6 7 SCK SI 0 1 0 1 1 0 0 1 HI-Z SO CS 0 1 2 3 4 5 6 7 SCK SI 0 0 1 1 1 1 0 0 HI-Z SO Software RECALL (RECALL) instruction When a RECALL instruction is executed, nvSRAM performs a Software RECALL operation. To issue this instruction, the device must be write enabled (WEN = ‘1’). The instruction is performed by transmitting the RECALL opcode on the SI pin following the falling edge of CS. The WEN bit is cleared on the positive edge of CS following the RECALL instruction. Figure 16. Software RECALL Operation CS 0 1 2 3 4 5 6 7 AutoStore Disable (ASDISB) instruction AutoStore is enabled by default in CY14B101Q2/CY14B101Q3. The ASDISB instruction disables the AutoStore. This setting is not nonvolatile and needs to be followed by a STORE sequence if this is desired to survive the power cycle. To issue this instruction, the device must be write enabled (WEN = ‘1’). The instruction is performed by transmitting the ASDISB opcode on the SI pin following the falling edge of CS. The WEN bit is cleared on the positive edge of CS following the ASDISB instruction. Figure 18. AutoStore Disable Operation CS 0 1 2 3 4 5 6 7 SCK SI SO 0 0 0 1 1 0 0 1 HI-Z SCK SI SO 0 1 1 0 0 0 0 0 HI-Z Document #: 001-50091 Rev. *H Page 13 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Best Practices HOLD Pin Operation The HOLD pin is used to pause the serial communication. When the device is selected and a serial sequence is underway, HOLD is used to pause the serial communication with the master device without resetting the ongoing serial sequence. To pause, the HOLD pin must be brought LOW when the SCK pin is LOW. CS pin must remain LOW along with HOLD pin to pause serial communication. While the device serial communication is paused, inputs to the SI pin are ignored and the SO pin is in the high impedance state. To resume serial communication, the HOLD pin must be brought HIGH when the SCK pin is LOW (SCK may toggle during HOLD). nvSRAM products have been used effectively for over 27 years. While ease-of-use is one of the product’s main system values, experience gained working with hundreds of applications has resulted in the following suggestions as best practices: ■ The nonvolatile cells in this nvSRAM product are delivered from Cypress with 0x00 written in all cells. Incoming inspection routines at customer or contract manufacturer’s sites sometimes reprogram these values. Final NV patterns are typically repeating patterns of AA, 55, 00, FF, A5, or 5A. End product’s firmware should not assume an NV array is in a set programmed state. Routines that check memory content values to determine first time system configuration, cold or warm boot status, and so on should always program a unique NV pattern (that is, complex 4-byte pattern of 46 E6 49 53 hex or more random bytes) as part of the final system manufacturing test to ensure these system routines work consistently. ■ Power-up boot firmware routines should rewrite the nvSRAM into the desired state (for example, AutoStore Enabled). While the nvSRAM is shipped in a preset state, best practice is to again rewrite the nvSRAM into the desired state as a safeguard against events that might flip the bit inadvertently such as program bugs and incoming inspection routines. ■ The VCAP value specified in this data sheet includes a minimum and a maximum value size. Best practice is to meet this requirement and not exceed the maximum VCAP value because the nvSRAM internal algorithm calculates VCAP charge and discharge time based on this maximum VCAP value. Customers that want to use a larger VCAP value to make sure there is extra STORE charge and STORE time should discuss their VCAP size selection with Cypress to understand any impact on the VCAP voltage level at the end of a tRECALL period. Figure 19. HOLD Operation SCK HOLD ~ ~ CS SO Document #: 001-50091 Rev. *H Page 14 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Maximum Ratings Exceeding maximum ratings may shorten the useful life of the device. These user guidelines are not tested. Transient voltage (<20 ns) on any pin to ground potential .................. –2.0 V to VCC + 2.0 V Storage temperature ................................ –65 °C to +150 °C Package power dissipation capability (TA = 25 °C) .................................................. 1.0 W Maximum accumulated storage time At 150 °C ambient temperature................... .... 1000 h At 85 °C ambient temperature.................. ... 20 Years Ambient temperature with power applied ........................................... –55 °C to +150 °C Supply voltage on VCC relative to VSS ..........–0.5 V to +4.1 V DC voltage applied to outputs in High-Z state ..................................... –0.5 V to VCC + 0.5 V Surface mount lead soldering temperature (3 Seconds).......................................... +260 °C DC output current (1 output at a time, 1s duration)..... 15 mA Static discharge voltage.......................................... > 2001 V (per MIL-STD-883, Method 3015) Latch up current..................................................... > 200 mA Table 9. Operating Range Input voltage ........................................ –0.5 V to VCC + 0.5 V Range Ambient Temperature VCC –40 °C to +85 °C 2.7 V to 3.6 V Industrial DC Electrical Characteristics Over the Operating Range (VCC = 2.7 V to 3.6 V) Parameter Description Test Conditions Min Typ[4] Max Unit 2.7 3.0 3.6 V VCC Power supply voltage ICC1 Average Vcc current At fSCK = 40 MHz. Values obtained without output loads (IOUT = 0 mA) – – 10 mA ICC2 Average VCC current during STORE All inputs don’t care, VCC = Max. Average current for duration tSTORE – – 10 mA ICC4 Average VCAP current All inputs don’t care. Average current for duration tSTORE during AutoStore cycle – – 5 mA ISB VCC standby current – – 5 mA IIX[5] Input leakage current VCC = Max, VSS < VIN < VCC (except HSB) –1 – +1 µA Input leakage current VCC = Max, VSS < VIN < VCC (for HSB) –100 – +1 µA –1 – +1 µA CS > (VCC – 0.2 V). VIN < 0.2 V or > (VCC – 0.2 V). Standby current level after nonvolatile cycle is complete. Inputs are static. f = 0 MHz. IOZ Off state output leakage current VCC = Max, VSS < VOUT < VCC VIH Input HIGH voltage 2.0 – VCC + 0.5 V VIL Input LOW voltage VSS – 0.5 – 0.8 V VOH Output HIGH voltage IOUT = –2 mA 2.4 – – V VOL Output LOW voltage IOUT = 4 mA – – 0.4 V VCAP Storage capacitor Between VCAP pin and VSS, 5 V rated 61 68 180 µF Notes 4. Typical values are at 25 °C, VCC= VCC (Typ). Not 100% tested. 5. The HSB pin has IOUT = -2 uA for VOH of 2.4 V when both active high and LOW drivers are disabled. When they are enabled standard VOH and VOL are valid. This parameter is characterized but not tested. Document #: 001-50091 Rev. *H Page 15 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Data Retention and Endurance Parameter Description DATAR Data retention NVC Nonvolatile STORE operations Min Unit 20 Years 1,000 K Max Unit 6 pF 8 pF Capacitance Parameter[6] Description Test Conditions CIN Input capacitance COUT Output pin capacitance TA = 25 °C, f = 1 MHz, VCC = VCC (Typ) Thermal Resistance Parameter [6] Description ΘJA Thermal resistance (junction to ambient) ΘJC Thermal resistance (junction to case) Test Conditions Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA / JESD51. 16-SOIC 8-DFN Unit 55.17 17.7 °C/W 2.64 18.8 °C/W Figure 20. AC Test Loads and Waveforms 577 Ω 577 Ω 3.0 V 3.0 V R1 R1 OUTPUT OUTPUT 30 pF R2 789 Ω 5 pF R2 789 Ω AC Test Conditions Input pulse levels....................................................0 V to 3 V Input rise and fall times (10% - 90%)............................ <3 ns Input and output timing reference levels........................ 1.5 V Note 6. These parameters are guaranteed by design and are not tested. Document #: 001-50091 Rev. *H Page 16 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 AC Switching Characteristics Cypress Parameter fSCK tCL tCH tCS tCSS tCSH tSD tHD tHH tSH tCO tHHZ[7] tHLZ[7] tOH tHZCS Alt. Parameter fSCK tWL tWH tCE tCES tCEH tSU tH tHD tCD tV tHZ tLZ tHO tDIS 40 MHz Description Min – 11 11 20 10 10 5 5 5 5 – – – 0 – Clock frequency, SCK Clock pulse width LOW Clock pulse width HIGH CS HIGH time CS setup time CS hold time Data in setup time Data in hold time HOLD hold time HOLD setup time Output valid HOLD to output High Z HOLD to output Low Z Output hold time Output disable time Unit Max 40 – – – – – – – – – 9 15 15 – 25 MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns Figure 21. Synchronous Data Timing (Mode 0) tCS CS tCH tCL tCSH ~ ~ tCSS SCK tSD tHD VALID IN SI tCO SO tOH HI-Z tHZCS HI-Z Figure 22. HOLD Timing ~ ~ CS SCK tHH tHH tSH tSH HOLD tHHZ tHLZ SO Note 7. These parameters are guaranteed by design and are not tested. Document #: 001-50091 Rev. *H Page 17 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 AutoStore or Power-Up RECALL Parameter Power-Up RECALL duration tFA [8] tSTORE CY14B101Q1/CY14B101Q2/ CY14B101Q3 Min Max – 20 Description Unit ms [9] STORE cycle duration – 8 ms [10] Time allowed to complete SRAM cycle – 25 ns – 150 2.65 – V μs tDELAY VSWITCH tVCCRISE [11] Low voltage trigger level VCC rise time VHDIS[11] HSB output disable voltage – 1.9 V tLZHSB[11] tHHHD[11] HSB high to nvSRAM active time – 5 μs HSB high active time – 500 ns Switching Waveforms Figure 23. AutoStore or Power-Up RECALL[12] VCC VSWITCH VHDIS t VCCRISE tHHHD Note 9 9 tSTORE Note tHHHD 13 Note tSTORE Note 13 HSB OUT tDELAY tLZHSB AutoStore tLZHSB tDELAY POWERUP RECALL tFA tFA Read & Write Inhibited (RWI) POWER-UP RECALL Read & Write BROWN OUT AutoStore POWER-UP RECALL Read & Write POWER DOWN AutoStore Notes 8. tFA starts from the time VCC rises above VSWITCH. 9. If an SRAM write has not taken place since the last nonvolatile cycle, AutoStore or Hardware STORE is not initiated 10. On a Hardware STORE, Software STORE / RECALL, AutoStore Enable / Disable and AutoStore initiation, SRAM operation continues to be enabled for time tDELAY. 11. These parameters are guaranteed by design and are not tested. 12. Read and Write cycles are ignored during STORE, RECALL, and while VCC is below VSWITCH. 13. During power up and power down, HSB glitches when HSB pin is pulled up through an external resistor Document #: 001-50091 Rev. *H Page 18 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Software Controlled STORE and RECALL Cycles Parameter CY14B101Q1/CY14B101Q2/ CY14B101Q3 Description Min Max Unit tRECALL RECALL duration – 200 μs tSS [14, 15] Soft sequence processing time – 100 μs Figure 24. Software STORE Cycle[15] CS CS 0 1 2 3 4 5 6 7 0 SCK SI Figure 25. Software RECALL Cycle[15] 1 2 3 4 5 6 7 SCK 0 0 1 1 1 1 0 0 SI 0 1 1 0 0 0 0 0 tRECALL tSTORE HI-Z RWI RDY RDY Figure 26. AutoStore Enable Cycle Figure 27. AutoStore Disable Cycle CS CS 0 1 2 3 4 5 6 0 7 1 2 3 4 5 6 7 SCK SCK SI HI-Z RWI 0 1 0 1 1 0 0 SI 1 0 0 0 1 1 0 0 1 tSS tSS RWI HI-Z RDY RWI HI-Z RDY Notes 14. This is the amount of time it takes to take action on a soft sequence command. Vcc power must remain HIGH to effectively register command. 15. Commands such as STORE and RECALL lock out IO until operation is complete which further increases this time. See the specific command. Document #: 001-50091 Rev. *H Page 19 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Hardware STORE Cycle Parameter tPHSB CY14B101Q3 Description Hardware STORE pulse width Min Max 15 – Unit ns Figure 28. Hardware STORE Cycle[16] Write Latch set ~ ~ tPHSB HSB (IN) tSTORE tHHHD ~ ~ tDELAY HSB (OUT) tLZHSB RWI tPHSB HSB (IN) HSB pin is driven HIGH to VCC only by Internal 100 K: resistor, HSB driver is disabled SRAM is disabled as long as HSB (IN) is driven LOW. tDELAY RWI ~ ~ HSB (OUT) ~ ~ Write Latch not set Note 16. If an SRAM write has not taken place since the last nonvolatile cycle, no AutoStore or Hardware STORE takes place. Document #: 001-50091 Rev. *H Page 20 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Ordering Information Ordering Code Package Diagram Package Type Operating Range CY14B101Q2-LHXI 001-50671 8-pin DFN (With VCAP) Industrial All the above parts are Pb-free. Ordering Code Definition CY 14 B 101 Q 1-SF X I T Option: T - Tape and Reel Blank - Std. Pb-free Temperature: I - Industrial (-40 to 85 °C) Package: SF - 16 SOIC LH - 8 DFN 1 - With WP 2 - With VCAP 3 - With VCAP, WP and HSB Q - Serial SPI nvSRAM Voltage: B - 3.0 V Density: 101 - 1 Mb 14 - nvSRAM Cypress Document #: 001-50091 Rev. *H Page 21 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Package Diagrams Figure 29. 8-Pin (196 mil) DFN Package (001-50671) NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS 2. PACKAGE WEIGHT: TBD 3. BASED ON REF JEDEC # MO-240 EXCEPT DIMENSIONS (L) and (b) Document #: 001-50091 Rev. *H 001-50671 *B Page 22 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Package Diagrams (continued) Figure 30. 16-Pin (300 mil) SOIC (51-85022) 51-85022 *C Document #: 001-50091 Rev. *H Page 23 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Acronyms Document Conventions Acronym Description Units of Measure CPHA Clock phase CPOL Clock polarity °C degrees Celsius Dual flat no-lead Hz Hertz DFN EEPROM Electrically erasable programmable read-only memory EIA Electronic Industries Alliance I/O Input/output nvSRAM nonvolatile static random access memory RoHS Restriction of hazardous substances SOIC Small outline integrated circuit SONOS SPI Silicon-oxide-nitride-oxide-silicon Serial peripheral interface Document #: 001-50091 Rev. *H Symbol Unit of Measure kbit 1024 bits kHz kilohertz KΩ kilo ohms μA microamperes mA milliampere μF microfarads MHz megahertz μs microseconds ms millisecond ns nanoseconds pF picofarads V volts Ω ohms W watts Page 24 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Document History Page Document Title: CY14B101Q1/CY14B101Q2/CY14B101Q3 1 MBit (128K x 8) Serial SPI nvSRAM Document Number: 001-50091 Orig. of Submission Rev. ECN No. Description of Change Change Date ** 2607408 GSIN/ 12/19/08 New Datasheet GVCH/AESA *A 2654487 GVCH/PYRS 02/04/2009 Moved from Advance information to Preliminary Changed part number from CY14B101QxA to CY14B101Qx Updated pin description of VCAP pin Updated Device operation and SPI peripheral interface description Added Factory setting values for BP1, BP2 and WPEN bits Updated Real Time Clock operation description Changed ICC2 from 5mA to 10mA *B 2733293 GVCH/AESA 07/08/2009 Corrected typo error in the Document History Page (Description of change) Corrected Typo error of footnote 2 and 3 Updated AutoStore operation description Updated test condition of ICC1 and ISB parameter Updated VHDIS parameter description *C 2757348 08/28/2009 08/28/2009 Moved data sheet status from Preliminary to Final Removed commercial temperature related specs Added thermal resistance values for 16-SOIC and DFN package Added note to Write Sequence (WRITE) description *D 2839453 GVCH/PYRS 01/06/10 Changed STORE cycles to QuantumTrap from 200K to 1 Million Updated Figure 3 Added Contents *E 2894833 GVCH 03/17/10 Removed inactive parts from the Ordering Information table. Updated links in Sales, Solutions, and Legal Information. Updated Package Diagrams. *F 2910569 BTK/GVCH 04/12/10 Updated Figure 1 to show the pad in the pin diagrams. Updated Table 1 to give information on the pad. Updated Power-Down description Power On Reset: Added status of bits 4-6 Table 5: Added definition of bits 4-6 Updated Figure 21, Figure 22, and Figure 23 Updated footnote 11 Removed tDHSB parameter Updated Figure 28 *G 3037045 GVCH 10/09/10 Changed ground naming convention from GND to VSS Updated Power-Down description Power On Reset: Added status of bits 4-6 Table 5: Added definition of bits 4-6 Updated Figure 8 Updated HOLD Pin Operation, Figure 19 and Figure 22 to indicate that CS pin must remain LOW along with HOLD pin to pause serial communication Added Figure 26 and Figure 27 Added Acronyms and Units of Measure table *H 3134300 GVCH 01/11/2011 Hardware STORE and HSB Pin Operation: Added more clarity on HSB pin operation Updated tLZHSB parameter description Document #: 001-50091 Rev. *H Page 25 of 26 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive psoc.cypress.com/solutions cypress.com/go/clocks PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/go/memory cypress.com/go/image cypress.com/go/psoc cypress.com/go/touch cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2010-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document #: 001-50091 Rev. *H Revised January 18, 2011 Page 26 of 26 All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback