PI3CH200 ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| 2-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Description Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching 0 to 5V switching with 3.3V power supply 0 to 3.3V switching with 2.5V power supply 5V I/O tolerant with supply in OFF and ON state 1.8V, 2.5V and 3.3V supply voltage operation Hot Insertion Capable Industrial Operating Temperature: -40ºC to +85ºC 8kV ESD Protection (human body model) Latch-up Performance: >200mA per JESD17 Packaging (Pb-free & Green available): -8-pin TSSOP (L) The PI3CH200 is a low voltage, 2-channel switch designed with fast individual enables. The switch introduces no additional ground bounce noise or additional propagation delay. The PI3CH200 device has active low enables. It is very useful in switching signals that have high bandwidth (500 MHz). Applications High Bandwidth Data Switching Hot-Docking Analog Signal Switching Differential Signal Switching Block Diagram Pin Configuration EN1 A2 B2 EN2 Pin Description Pin No 1, 7 Pin Name 1111111 ENx Ax Bx VCC A Ports X Hi-Z Hi-Z GND Disconnect H Hi-Z Hi-Z VCC Disconnect Ax VCC Connect 2, 5 EN1, EN2 A1, A2 3, 6 B1, B2 B Ports 4 GND VCC Ground Power 8 Truth Table(1) Description Switch Enables L Bx Note: Function 1. H=High Voltage Level; L=Low Voltage Level; Hi-Z=High Impedance 2013-03-0014 PT0479 1 03/22/13 PI3CH200 2-Bit Bus Switch, Enable Low1.8V/2.5V/ 3.3V, High-Bandwidth, Hot Plug ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Maximum Ratings Storage Temperature ................................................................................... -65oC to +150oC Ambient Temperature with Power Applied........................................–40°C to +85°C Supply Voltage to Ground Potential ............................................................-0.5V to + 4.6V DC Input Voltage ............................................................................................-0.5V to + 6.0V DC Output Current .......................................................................................... 120mA Power Dissipation .............................................................................................................. 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics 3.3V supply (Over operating range, TA = -40 ~ +85ºC, VCC=3.3V±10%, unless otherwise noted) Symbol Description Test Conditions(1) Min Typ(2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 - - V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.5 - 0.8 V VIK Clamp Diode Voltage VCC = Min., IIN = -18mA - -1.3 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC - - ±1 μA IIL Input Low Current VCC = Max., VIN = GND - - ±1 μA 0 ≤ A, B ≤ VCC VCC = Min., VIN = 0.0V ION = -48mA or -64mA VCC = Min., VIN = 3.6V ION = -15mA - - ±1 μA - 4 6 - 5 8 IOZH High-Impedance Current RON Switch On-Resistance(3) Ω Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Ax, Bx) pins. 2.5V supply (Over operating range, TA = -40 ~ +85ºC, VCC=2.5V±10%, unless otherwise noted) Symbol Description Test Conditions(1) Min Typ(2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 1.8 - VCC+0.3 V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.3 - 0.8 V VIK Clamp Diode Voltage VCC = Max., IIN = -6mA - -0.7 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC - - ±1 μA IIL Input Low Current VCC = Max., VIN = GND - - ±1 μA - - ±1 μA - 4 8 - 7 14 IOZH High-Impedance Current RON Switch On-Resistance(3) 0 ≤ A, B ≤ VCC VCC = Min., VIN = 0.0V ION = -48mA VCC = Min., VIN = 2.25V ION = -15mA Ω Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 2.5V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Ax, Bx) pins. 2013-03-0014 PT0479 2 03/22/13 PI3CH200 2-Bit Bus Switch, Enable Low1.8V/2.5V/ 3.3V, High-Bandwidth, Hot Plug ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| 1.8V supply (Over operating range, TA = -40 ~ +85ºC, VCC=1.8V±10%, unless otherwise noted) Symbol Test Conditions(1) Description Min Typ(2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 1.2 - VCC+0.3 V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.3 - 0.6 V VIK Clamp Diode Voltage VCC = Min., IIN = -18mA - -0.7 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC - - ±1 μA IIL Input Low Current VCC = Max., VIN = GND - - ±1 μA 0 ≤ A, B ≤ VCC VCC = Min., VIN = 0.0V ION = -48mA VCC = Min., VIN = 1.6V ION = -15mA - - ±1 μA - 4 8 - 10 18 IOZH High-Impedance Current RON Switch On-Resistance(3) Ω Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 1.8V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Ax, Bx) pins. Capacitance (TA = 25ºC, f=1MHz) Symbol(1) Description Typ(2) Test Conditions CIN Input Capacitance COFF A/B Capacitance, Switch Off CON A/B Capacitance, Switch On Unit 2.0 VIN = 0V 3.5 pF 7.0 Note: 1. These parameters are determined by device characterization but are not production tested Power Supply Characteristics Symbol ICC Test Conditions(1) Description Quiescent Power Supply Current Min Typ Max Unit VCC = 3.6V, VIN = GND or VCC - 0.2 0.5 mA VCC = 2.5V, VIN = GND or VCC - 0.15 0.4 mA VCC = 1.8V, VIN = GND or VCC - 0.8 1.5 mA Note: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at +25°C ambient Dynamic Electrical Characteristics (Over Operating Range, TA = -40 ~ +85ºC, VCC=3.3V±10%) Symbol Description Test Conditions Min Typ Max XTALK Crosstalk 10MHz - -60 - OIRR Off-Isolation 10MHz - -60 - BW -3dB Bandwidth See test Diagram - 500 - Unit dB MHz Switch Characteristics Over 3.3V Operating Range Symbol tPLH, tPHL Test Conditions(1) Description (2, 3) Propagation Delay Ax to Bx, Bx to Ax Min Typ Max See test Diagram - - 0.3 tPZH, tPZL Enable Time ENx to Ax or Bx See test Diagram 1.5 - 9.0 tPHZ, tPLZ Disable Time ENx to Ax or Bx See test Diagram 1.5 - 9.0 2013-03-0014 PT0479 3 Unit ns 03/22/13 PI3CH200 2-Bit Bus Switch, Enable Low1.8V/2.5V/ 3.3V, High-Bandwidth, Hot Plug ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Over 2.5V Operating Range Symbol tPLH, tPHL Test Conditions(1) Description (2, 3) Propagation Delay Ax to Bx, Bx to Ax Min Typ Max See test Diagram - - 0.3 tPZH, tPZL Enable Time ENx to Ax or Bx See test Diagram 1.5 - 15.0 tPHZ, tPLZ Disable Time ENx to Ax or Bx See test Diagram 1.5 - 12.0 Unit ns Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Over 1.8V Operating Range Symbol tPLH, tPHL Test Conditions(1) Description (2, 3) Propagation Delay Ax to Bx, Bx to Ax Min Typ Max See test Diagram - - 0.3 tPZH, tPZL Enable Time ENx to Ax or Bx See test Diagram 1.5 - 25.0 tPHZ, tPLZ Disable Time ENx to Ax or Bx See test Diagram 1.5 - 12.0 Unit ns Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Test Circuit for Electrical Characteristics 6.0V VCC 200Ω Pulse Generator VIN VOUT D.U.T RT 10pF CL 200Ω Notes: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator 3. All input impulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50-ohm, tR ≤ 2.5ns, tF ≤ 2.5ns. 4. The outputs are measured one at a time with one transition per measurement. 2013-03-0014 PT0479 4 03/22/13 PI3CH200 2-Bit Bus Switch, Enable Low1.8V/2.5V/ 3.3V, High-Bandwidth, Hot Plug ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Switch Positions Test Switch tPLZ, tPZL 6.0V tPHZ, tPZH GND Prop Delay Open Test Circuit for Dynamic Electrical Characteristics Switching Waveforms 2013-03-0014 PT0479 5 03/22/13 PI3CH200 2-Bit Bus Switch, Enable Low1.8V/2.5V/ 3.3V, High-Bandwidth, Hot Plug ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Applications Information Logic Inputs The logic control inputs can be driven up to 3.6V regardless of the supply voltage. For example, given a +3.3V supply, EN may be driven LOW to 0V and HIGH to 3.6V. Driving EN Rail-to-Rail® minimizes power consumption. Power Supply-Sequencing Proper power supply sequencing is recommended for all CMOS devices. Always apply VCC before applying signals to the input/ output or control pins. Hot Insertion For Datacom and Telecom applications that have ten or more volts passing through the backplane, a high voltage from the power supply may be seen at the device input pins during hot insertion. The PI3CH200 devices have maximum limits of 6V and 120mA for 20ns. If the power is higher or applied for a longer time or repeatedly reaches the maximum limits, the devices can be damaged. Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. 2013-03-0014 PT0479 6 03/22/13 PI3CH200 2-Bit Bus Switch, Enable Low1.8V/2.5V/ 3.3V, High-Bandwidth, Hot Plug ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Mechanical Information 8-Pin TSSOP(L) Note: 1) Controlling dimensions in millimeters. PKG. DIMENSIONS(MM) SYMBOL MIN MAX A 1.20 A1 0.02 0.15 A2 0.80 1.00 b 0.19 0.30 c 0.09 0.20 D 2.90 3.10 E 4.30 4.50 E1 6.25 6.55 e 0.65 BSC L 0.50 0.70 θ 1° 7° Ordering Information Package Cede Part No. PI3CH200LE Package Lead free and Green 8-Pin TSSOP L Note: E = Pb-free or Pb-free & Green Adding X Suffix= Tape/Reel Pericom Semiconductor Corporation 1-800-435-2336 www.pericom.com Pericom reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply the best possible product. Pericom does not assume any responsibility for use of any circuitry described other than the circuitry embodied in Pericom product. The company makes no representations that circuitry described herein is free from patent infringement or other rights, of Pericom. 2013-03-0014 PT0479 7 03/22/13