PULSE T-3200SCT

Copperhead
High Speed
Dual transformerS
TM
Military / Aerospace Division
Compliant with ANSI X3T111, Fiber Channel,
FC-PH-3 for quarter/full speed applications, SMPTE,
IEEE1394 Firewire
Moisture sensitivity Level 3
Pick and place compatible
IC grade package withstands 225°C peak temperature profile
AS9100 Certified (Based on and including ISO 9001:2000)
Electrical Specifications @ 25°C — Operating Temperature -55°C to +125°C
Part
Turns Ratio Primary Inductance
Number
(±5%)
(µH MIN)
T-330SCT
T-531SCT
T-1062SCT
T-1250SCT
T-1485SCT
T-3200SCT
1CT:1CT
1CT:1CT
1CT:1CT
1CT:1CT
1CT:1CT
1:1
Rise Time
Hi-Pot
Insertion Loss
@ 20& to 80% DC Resistance
(W MAX) (Vrms MIN)
(dB MAX)
(pS MAX)
26 @ 1Vrms, 100kHz
7.5@1Vrms, 100kHz
3.75@1Vrms, 100kHz
3.75@1Vrms, 100kHz
3.75@1Vrms, 100kHz
0.70
350
325
280
280
280
200
0.2
0.2
0.2
0.2
0.2
0.2
1,500
1,500
1,500
1,500
1,500
1,500
Application
Nominal Bit Rate
(Mbaud)
-1.5 @ 15-165MHz
265.6 (1/4 speed)
-2.0 @ 50-265MHz
531 (half speed)
-2.0 @ 100-531MHz 1,062.5 (full speed)
-2.0@125-650MHz
1,250
-2.0
1,485 (SMTPE)
-4.5
3,200
NOTES: 1. To order a RoHS compliant part, add the suffix “NL” to the part number, i.e. T-330SCT becomes T-330SCTNL.
2. Add suffix “T” to part number for Tape & Reel package (i.e. T-330SCTT).
Mechanical
Schematic
T-330SCT, T-531SCT, T-1062SCT, T-1250SCT and T-1485SCT
����
����
�����
���
�����
�����������
���������
�����������������
���� �����
�����
���� ���
����
����
����� ����
����� ����
����
���
����
����������
����������
����
����
�
��
�
��
�
��
�
��
�
��
�
��
�
��
�
�
���������������������
����
����
����
���
����
�����������
�����������
����
���
����
���
����
����
������
���
����
����
Weight . . . . . . . . . . . . . . . 1.0 grams
Tape & Reel . . . . . . . . . . . . . 400/reel
Dimensions: Inches
mm
Unless otherwise specified,
all tolerances are ± .005
0,13
USA 215 781 6400 ● Germany 49 7032 7806 0 ● Singapore 65 6287 8998 ● Shanghai 86 21 32181071 ● China 86 755 33966678 ● Taiwan 886 3 4643715
www.pulseeng.com
M105.D (2/10)
Copperhead
High Speed
Dual transformerS
TM
Military / Aerospace Division
Mechanical
T-3200SCT
Schematic
����
����
�����
���
�����
����
����
����
����
���������
���������
�����������������
����
����
����������
����������
����� ����
����� ����
���
����
���
����
����
����
���������������������
����
���
����
����
����
����
����
���
���
��
�
��
�
��
�
��
�
��
�
��
�
��
�
�
Weight . . . . . . . . . . . . . . . 1.0 grams
Tape & Reel . . . . . . . . . . . . . 600/reel
Dimensions: Inches
mm
Unless otherwise specified,
all tolerances are ± .005
0,13
�������
����
���
����
�����������
�����������
�
����
����
Application Notes
Pulse Specialty Components has designed Fibre Channel dual transformers specifically for point to point coupling to 150 twinax cable.
The isolation transformers protect the station from static charges that
may develop on the cable, and prevents ground loop currents from
being transferred between stations. The devices have also been
designed to provide common mode rejection within the transmission
��������
��������
��
��
��������� ������ ���������
�������
��
������
����
�
������
���
�
��
����
��
���������
�������
���
�����������
��������
���
�
�
�
��
���
��
�
��
�
�
�
�����������
��������
��
���
���
��
����
��
��
������
����
�
������
����
���������
������������������������������������
1. The transformer, 51W resistors, and the impedance of the driver
are matched to achieve the best return loss (S11) for the transmitter of the 150W system.
2. The total impedance of termination resistor network is 150 W.
3. When laying out PCB, transmission line methods must be utilized
to maintain return loss and signal integrity. Transformer must be
��
���������
�������
���
���������
��
band and thus reduce EMI. The wide bandwidth of these devices
minimizes data dependent jitter by providing fast signal rise times.
Low-end bandwidth also minimizes base-line wander, another contributor to jitter. The dual package allows connection of both transmit
and receive channels, as shown in the application circuit below.
Surface-mount packaging also allows a cost-effective solution.
�������
���
��
��
�������
���
located within .50” of the DB9 connector.
4. It is recommended that the center tap (CT) of transformer(s), cable
side, be connected to earth/chassis (cable shield) ground either
directly or via a transient voltage suppressor (TVS) type component and earth/chassis ground should be “AC-coupled” to signal
(digital) ground through a .027uF, 500V capacitor.
For More Information:
Pulse Worldwide
Headquarters
Two Pearl Buck Court
Bristol, PA 19007
U.S.A.
www.pulseeng.com
Tel: 215 781 6400
Fax: 215 781 6403
Pulse Europe
Pulse China Headquarters Pulse North China
Pulse South Asia
Pulse North Asia
Einsteinstrasse 1
D-71083 Herrenberg
Germany
B402, Shenzhen Academy of
Aerospace Technology Bldg.
10th Kejinan Rd.
High-Tech Zone
Nanshan District
Shenzen, PR China 518057
TEL: 86 755 33966678
FAX: 86 755 33966700
Room 2704/2705
Super Ocean Finance Ctr.
2067 Yan An Rd. West
Shanghai 200336
China
135 Joo Seng Rd.
#03-02
PM Industrial Bldg.
Singapore 368363
No. 26, Kao Ching Rd.
Yang Mei Chen
Taoyuan Hsien
Taiwan
R. O. C.
Tel: 86 21 62787060
Fax: 86 2162786973
TEL: 65 6287 8998
FAX: 65 6280 0080
Tel: 886 3 4643715
Fax: 886 3 4641911
Tel: 49 7032 7806 0
Fax: 49 7032 7806 135
Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product
names mentioned herein may be trademarks or registered trademarks of their respective owners.
© Copyright, 2010. Pulse Engineering, Inc. All rights reserved.
www.pulseeng.com
M105.D (2/10)