RAMTRON FM31T374-G

Preliminary
FM31T372/374/376/378
System Supervisor & Temperature Compensated RTC
(TCXO) with Embedded Crystal
Features
High Integration Device Replaces Multiple Parts
 Real-time Clock (RTC)
o Embedded 32.768kHz Crystal
o Temperature Compensated
 32.768 kHz Clock Output
 Low-VDD Detection Drives Reset
 Watchdog Timer
 Early Power-Fail Warning/NMI
 Two 16-bit Event Counters with Event Driven
Interrupt Output
 Serial Number with Write-lock for Security
Ferroelectric Nonvolatile RAM
 4Kb, 16Kb, 64Kb, and 256Kb versions
 Unlimited Read/Write Endurance
 10 year Data Retention
 NoDelay™ Writes
Real-time Clock/Calendar
 Temp-Compensated Using On-Chip Sensor
o  5 ppm over -40°C to +85°C
o Accuracy  2 ½ min. per year
 Backup Current 1.4 A (max.) at +25C
 Seconds through Centuries in BCD format
 Tracks Leap Years through 2099
Description
The FM31T37x is a family of integrated devices that
includes the most commonly needed functions for
processor-based systems. Major features include
nonvolatile F-RAM memory available in various
sizes, temperature-compensated real-time clock with
embedded crystal, 32.768kHz clock output,
low-VDD reset, watchdog timer, battery backed
event counter, event driven interrupt output, lockable
64-bit serial number area, general purpose
comparator that can be used for an early power-fail
(NMI) interrupt or other purpose, and 2-wire serial
interface to a host microcontroller. The family
operates from 2.7 to 5.5V.
The real-time clock (RTC) provides time and date
information in BCD format. It can be permanently
powered from external backup voltage source, either
a battery or a capacitor. The timekeeper uses an
internal 32.768 kHz crystal which is factorycalibrated for excellent timekeeping accuracy over
the industrial temperature range.
This is a product that has fixed target specifications but are subject
to change pending characterization results.
Rev. 1.1
Apr. 2011



No External Crystal Required
Offset Register to Correct for Crystal Aging
Supports Battery or Capacitor Backup
Processor Companion
 32.768 kHz Clock Output
 Active-low Reset Output for VDD and Watchdog
 Programmable VDD Reset Trip Point
 Manual Reset Filtered and Debounced
 Programmable Watchdog Timer
 Dual Battery-backed Event Counter Tracks
System Intrusions or other Events
 Event Counter Driven Interrupt Output
 Comparator for Early Power-Fail Interrupt
 64-bit Programmable Serial Number with Lock
Fast Two-wire Serial Interface
 Up to 1 MHz Maximum Bus Frequency
 Supports Legacy Timing for 100 kHz & 400 kHz
 Device Select Pins for up to 4 Memory Devices
 RTC, Supervisor Controlled via 2-wire Interface
Easy to Use Configurations
 Operates from 2.7 to 5.5V
 Small Footprint 14-pin “Green” SOIC (-G)
 Low Operating Current
 -40C to +85C Operation
The FM31T37x devices integrate 4Kb, 16Kb, 64Kb,
and 256Kb of F-RAM memory. F-RAM offers
superior write speed and unlimited endurance. This
allows the memory to provide system data collection
and as read/write RAM storage. This memory is truly
nonvolatile rather than battery-backed.
The processor companion includes commonly needed
CPU support functions. Supervisory functions
include a reset output signal controlled by either a
low VDD condition or a watchdog timeout. /RST
goes active when VDD drops below a programmable
threshold and remains active for 100 ms after VDD
rises above the trip point. A programmable watchdog
timer runs from 100 ms to 3 seconds. The watchdog
timer is optional, but if enabled it will assert the reset
signal for 100 ms if not restarted by the host before
the timeout. A flag-bit indicates the source of the
reset.
Ramtron International Corporation
1850 Ramtron Drive, Colorado Springs, CO 80921
(800) 545-FRAM, (719) 481-7000
http://www.ramtron.com
Page 1 of 26
FM31T372/374/376/378-G
A general-purpose comparator compares an external
input pin to the onboard 1.2V reference. This is
useful for generating a power-fail interrupt (NMI) but
can be used for any purpose. The family also includes
a programmable 64-bit serial number that can be
locked making it unalterable. Additionally it offers a
dual battery-backed event counter that tracks the
number of rising or falling edges detected on
dedicated input pins.
Pin Name
CNT1, CNT2
A0, A1
CAL/PFO
Pin Configuration
CNT1
1
14
VDD
CNT2
2
13
SCL
A0
3
12
SDA
A1
4
11
FOUT
CAL/PFO
5
10
/INT
RST
6
9
PFI
VSS
7
8
VBAK
/RST
VSS
VBAK
PFI
/INT
FOUT
SDA
SCL
VDD
Function
Event Counter Inputs
Device Select inputs
Clock Calibration and Early
Power-Fail Output
Reset Input/Output
Ground
Battery-Backup Supply
Early Power-fail Input
Event Counter Driven Interrupt
Output
32.768 kHz Clock Output
Serial Data
Serial Clock
Supply Voltage
Ordering Information
Base Configuration
FM31T378
FM31T376
FM31T374
FM31T372
Rev. 1.1
Apr. 2011
Memory Size
256Kb
64Kb
16Kb
4Kb
Operating Voltage
2.7-5.5V
2.7-5.5V
2.7-5.5V
2.7-5.5V
Reset Threshold
2.6V, 2.9, 3.9, 4.4V
2.6V, 2.9, 3.9, 4.4V
2.6V, 2.9, 3.9, 4.4V
2.6V, 2.9, 3.9, 4.4V
Ordering Part Number
FM31T378-G
FM31T376-G
FM31T374-G
FM31T372-G
Page 2 of 26
FM31T372/374/376/378-G
SCL
2-Wire
Interface
SDA
LockOut
A1, A0
F-RAM
Array
LockOut
RST
Watchdog
Special
Function
Registers
LV Detect
S/N
PFI
Temp
Sensor
+
-
CAL/PFO
1.2V
512Hz
FOUT
Temperature
Compensated
RTC
Event
Counters
-
~2.4V
RTC Registers
+
VDD
32.768
kHz
/INT
CNT1
CNT2
Switched Power
VBAK
Nonvolatile
Figure 1.
Battery Backed
Block Diagram
Pin Descriptions
Pin Name
Type
Pin Description
A0, A1
Input
CNT1, CNT2
Input
Device select inputs are used to address multiple memories on a serial bus. To select the device
the address value on the two pins must match the corresponding bits contained in the device
address. The device select pins are pulled down internally.
Event Counter Inputs: These battery-backed inputs increment counters when an edge is detected
on the corresponding CNT pin. The polarity is programmable. These pins should not be left
floating. Tie to ground if pins are not used.
Event Counter Driven Interrupt Output. This is a battery backed open-drain output. It goes low
for at least 100 ms upon changes on either CNT1 or CNT2 pin. This pin can be left floating if
not used.
In normal operation, this is the early power-fail output. In CAL mode, it supplies a 512 Hz
square-wave output for clock calibration.
32.768kHz Clock Output. This is a battery backed open-drain output. This pin can be disabled
by setting the FOEN bit to “0”. This pin can be left floating if not used.
Active low reset output with weak pull-up. Also input for manual reset.
Serial Data & Address: This is a bi-directional line for the two-wire interface. It is open-drain
and is intended to be wire-OR‟d with other devices on the two-wire bus. The input buffer
incorporates a Schmitt trigger for noise immunity and the output driver includes slope control
for falling edges. A pull-up resistor is required.
Serial Clock: The serial clock line for the two-wire interface. Data is clocked out of the device
on the falling edge, and into the device on the rising edge. The SCL input also incorporates a
Schmitt trigger input for noise immunity.
Early Power-fail Input: Typically connected to an unregulated power supply to detect an early
power failure. This pin should not be left floating.
Backup supply voltage: A 3V battery or a large value capacitor. If no backup supply is used, this
pin should be tied to VDD.
Supply Voltage
/INT
Output
CAL/PFO
Output
FOUT
Output
/RST
SDA
I/O
I/O
SCL
Input
PFI
Input
VBAK
Supply
VDD
Supply
Rev. 1.1
Apr. 2011
Page 3 of 26
FM31T372/374/376/378-G
Overview
The FM31T37x family combines a serial nonvolatile
F-RAM, a temperature compensated real-time clock
with embedded crystal, and a processor companion.
The companion is a highly integrated peripheral
including a processor supervisor, a comparator used
for early power-fail warning, nonvolatile event
counters, and a 64-bit serial number. The FM31T37x
integrates these complementary but distinct functions
that share a common interface in a single package.
Although monolithic, the product is organized as two
logical devices, the F-RAM memory, and the
RTC/companion. From the system perspective they
appear to be two separate devices with unique IDs on
the serial bus.
The memory is organized as a stand-alone 2-wire
nonvolatile memory with a standard device ID value.
The real-time clock and supervisor functions are
accessed with a separate 2-wire device ID. This
allows clock/calendar data to be read while
maintaining the most recently used memory address.
The clock and supervisor functions are controlled by
21 special function registers. The RTC and event
counter circuits are maintained by the power source
on the VBAK pin, allowing them to operate from
battery or backup capacitor power when VDD drops
below an internally set threshold. Each functional
block is described below.
Memory Operation
The FM31T37x is a family of products available in
different memory sizes including 4Kb, 16Kb, 64Kb,
and 256Kb. The family is software compatible, all
versions use consistent two-byte addressing for the
memory device. This makes the lowest density
device different from its stand-alone memory
counterparts but makes them compatible within the
entire family.
Memory is organized in bytes, for example the 4Kb
memory is 512 x 8 and the 256Kb memory is 32,768
x 8. The memory is based on F-RAM technology.
Therefore it can be treated as RAM and is read or
written at the speed of the two-wire bus with no
delays for write operations. It also offers effectively
unlimited write endurance unlike other nonvolatile
memory technologies. The 2-wire interface protocol
is described further on page 13.
The memory array can be write-protected by
software. Two bits in the processor companion area
(WP0, WP1 in register 0Bh) control the protection
setting as shown in the following table. Based on the
setting, the protected addresses cannot be written and
the 2-wire interface will not acknowledge any data to
Rev. 1.1
Apr. 2011
protected addresses. The special function registers
containing these bits are described in detail below.
Write protect addresses
None
Bottom ¼
Bottom ½
Full array
WP1
0
0
1
1
WP0
0
1
0
1
Processor Companion
In addition to nonvolatile RAM, the FM31T37x
family incorporates a highly integrated processor
companion. It includes a low voltage reset, a
programmable watchdog timer, battery-backed event
counters with interrupt output, a comparator for early
power-fail detection or other purposes, and a 64-bit
serial number.
Processor Supervisor
Supervisors provide a host processor two basic
functions: detection of power supply fault conditions
and a watchdog timer to escape a software lockup
condition. All FM31T37x devices have a reset pin
(/RST) to drive the processor reset input during
power faults (and power-up) and software lockups. It
is an open-drain output with a weak internal pull-up
to VDD. This allows other reset sources to be
wire-OR‟d to the /RST pin. When VDD is above the
programmed trip point, /RST output is pulled weakly
to VDD. If VDD drops below the reset trip point
voltage level (VTP) the /RST pin will be driven low. It
will remain low until VDD falls too low for circuit
operation which is the VRST level. When VDD rises
again above VTP, /RST will continue to drive low for
at least 100 ms (tRPU) to ensure a robust system reset
at a reliable VDD level. After tRPU has been met, the
/RST pin will return to the weak high state. While
/RST is asserted, serial bus activity is locked out even
if a transaction occurred as VDD dropped below VTP.
A memory operation started while VDD is above VTP
will be completed internally.
Figure 2 below illustrates the reset operation in
response to the VDD voltage.
VDD
tRPU
VTP
RST
Figure 2. Low Voltage Reset
Page 4 of 25
FM31T372/374/376/378-G
The bits VTP1 and VTP0 control the trip point of the
low voltage detect circuit. They are located in register
0Bh, bits 1 and 0.
VTP
2.6V
2.9V
3.9V
4.4V
VTP1
0 0
0 1
1 0
1 1
The watchdog timeout value is located in register
0Ah, bits 4-0, and the watchdog enable is bit 7. The
watchdog is restarted by writing the pattern 1010b to
the lower nibble of register 09h. Writing this pattern
will also cause the timer to load new timeout values.
Writing other patterns to this address will not affect
its operation. Note the watchdog timer is
free-running. Prior to enabling it, users should restart
the timer as described above. This assures that the
full timeout period will be set immediately after
enabling. The watchdog is disabled when VDD is
below VTP. The following table summarizes the
watchdog bits. A block diagram follows.
Rev. 1.1
Apr. 2011
Timebase
WR3-0 = 1010b to restart
Counter
/RST
VTP0
The watchdog timer can also be used to assert the
reset signal (/RST). The watchdog is a free running
programmable timer. The period can be software
programmed from 100 ms to 3 seconds in 100 ms
increments via a 5-bit nonvolatile register. All
programmed settings are minimum values and vary
with temperature according to the operating
specifications. The watchdog has two additional
controls associated with its operation, a watchdog
enable bit (WDE) and timer restart bits (WR). Both
the enable bit must be set and the watchdog must
timeout in order to drive /RST active. If a reset event
occurs, the timer will automatically restart on the
rising edge of the reset pulse. If WDE=0, the
watchdog timer runs but a watchdog fault will not
cause /RST to be asserted low. The WTR flag will be
set, indicating a watchdog fault. This setting is useful
during software development and the developer does
not want /RST to drive. Note that setting the
maximum timeout setting (11111b) disables the
counter to save power. The second control is a nibble
that restarts the timer preventing a reset. The timer
should be restarted after changing the timeout value.
Watchdog timeout
Watchdog enable
Watchdog restart
100 ms
clock
WDT4-0 0Ah, bits 4-0
WDE 0Ah, bit 7
WR3-0
09h, bits 3-0
Watchdog
timeout
WDE
Figure 3. Watchdog Timer
Manual Reset
The /RST pin is bi-directional and allows the
FM31T37x to filter and de-bounce a manual reset
switch. The /RST input detects an external low
condition and responds by driving the /RST signal
low for 100 ms. A manual reset does not set any
flags.
MCU
RST
FM31T37x
Reset
Switch
Switch
Behavior
RST
FM31T37x
drives
100 ms (min.)
Figure 4. Manual Reset
Note that an internal weak pull-up on /RST
eliminates the need for additional external
components.
Reset Flags
In case of a reset condition, a flag will be set to
indicate the source of the reset. A low VDD reset is
indicated by the POR flag, register 09h bit 6. A
watchdog reset is indicated by the WTR flag, register
09h bit 7. Note that the flags are internally set in
response to reset sources, but they must be cleared by
the user. When the register is read, it is possible that
both flags are set if both have occurred since the user
last cleared them.
Early Power Fail Comparator
An early power fail warning can be provided to the
processor well before VDD drops out of spec. The
comparator is used to create a power fail interrupt
(NMI). This can be accomplished by connecting the
PFI pin to the unregulated power supply via a resistor
divider. An application circuit is shown below.
Page 5 of 26
FM31T372/374/376/378-G
Regulator
VDD
C1P
16-bit Counter
CNT1
C2P
CNT2
FM31T37x
16-bit Counter
PFI
To MCU CAL/PFO
NMI input
CC
+
-
1.2V ref
Figure 6. Event Counter
Figure 5. Comparator as Early Power-Fail Warning
The voltage on the PFI input pin is compared to an
onboard 1.2V reference. When the PFI input voltage
drops below this threshold, the comparator will drive
the CAL/PFO pin to a low state. The comparator has
100 mV (max) of hysteresis to reduce noise
sensitivity, only for a rising PFI signal. For a falling
PFI edge, there is no hysteresis.
The comparator is a general purpose device and its
application is not limited to the NMI function.
The comparator is not integrated into the special
function registers except as it shares its output pin
with the CAL output. When the CAL mode is
invoked by setting the CAL bit (register 00h, bit 2),
the CAL/PFO output pin is driven with a 512 Hz
square wave and the comparator will be ignored.
Since most users only invoke the CAL mode during
production, this should have no impact on system
operations using the comparator.
Event Counter
The FM31T37x offers the user two battery-backed
event counters. Input pins CNT1 and CNT2 are
programmable edge detectors. Each clocks a 16-bit
counter. When an edge occurs, the counters will
increment their respective registers. Counter 1 is
located in registers 0Dh and 0Eh, Counter 2 is
located in registers 0Fh and 10h. These register
values can be read anytime VDD is above VTP, and
they will be incremented as long as a valid VBAK
power source is provided. To read, set the RC bit
register 0Ch bit 3 to 1. This takes a snapshot of all
four counter bytes allowing a stable value even if a
count occurs during the read. The registers can be
written by software allowing the counters to be
cleared or initialized by the system. Counts are
blocked during a write operation. The two counters
can be cascaded to create a single 32-bit counter by
setting the CC control bit (register 0Ch). When
cascaded, the CNT1 input will cause the counter to
increment. CNT2 is not used in this mode.
Rev. 1.1
Apr. 2011
The control bits for event counting are located in
register 0Ch. Counter 1 Polarity is bit C1P, bit 0;
Counter 2 Polarity is C2P, bit 1; the Cascade Control
is CC, bit 2; and the Read Counter bit is RC bit 3.
The polarity bits must be set prior to setting the
counter value(s). If a polarity bit is changed, the
counter may inadvertently increment. If the counter
pins are not being used, tie them to ground.
Event Counter Driven Interrupt Output
The event counter driven interrupt is a battery backed
open-drain output (/INT). A 100ms active low pulse
generated for the host microcontroller upon changes
on either CNT1 or CNT2 pins. The CNT2 pin will
not generate an interrupt if the CC bit is set to „1‟
(counter set to cascaded 32-bit mode).
MCU
FM31T37x
INT
Event occur
INT
100 ms
Figure 7. Event Counter Driven Interrupt Output
Serial Number
A memory location to write a 64-bit serial number is
provided. It is a writeable nonvolatile memory block
that can be locked by the user once the serial number
is set. The 8 bytes of data and the lock bit are all
accessed via the device ID for the processor
companion. Therefore the serial number area is
separate and distinct from the memory array. The
serial number registers can be written an unlimited
number of times, so these locations are general
purpose memory. However once the lock bit is set the
values cannot be altered and the lock cannot be
removed. Once locked the serial number registers can
still be read by the system.
Page 6 of 26
FM31T372/374/376/378-G
The serial number is located in registers 11h to 18h.
The lock bit is SNL, register 0Bh bit 7. Setting the
SNL bit to „1‟ disables writes to the serial number
registers, and the SNL bit cannot be cleared.
Real-Time Clock (TCXO) Operation
The real-time clock is a timekeeping function that
can be battery or capacitor backed for continuous
operation. The RTC is operated by a temperature
compensated crystal oscillator (TCXO) based on an
embedded 32.768 kHz crystal.
The RTC consists of an oscillator, clock divider, and
a register system for user access. It divides down the
32.768 kHz time-base and provides a minimum
resolution of seconds (1Hz). Static registers provide
the user with read/write access to the time values. It
includes registers for seconds, minutes, hours,
day-of-the-week, date, months, and years. A block
diagram (Figure 8) illustrates the RTC function.
Figure 8. IBAK vs. VBAK Voltage
The minimum VBAK voltage varies linearly with
temperature. The user can expect the minimum VBAK
voltage to be 1.23V at +85°C and 1.90V at -40°C.
The tested limit is 1.55V at +25°C. The minimum
VBAK voltage has been characterized at -40°C and
+85°C but is not 100% tested.
The user registers are synchronized with the
timekeeper core using R and W bits in register 00h
described below. Changing the R bit from „0‟ to „1‟
transfers timekeeping information from the core into
holding registers that can be read by the user. If a
timekeeper update is pending when R is set, then the
core will be updated prior to loading the user
registers. The registers are frozen and will not be
updated again until the R bit is cleared to „0‟. R is
used for reading the time.
Setting the W bit to „1‟ locks the user registers.
Clearing it to „0‟ causes the values in the user
registers to be loaded into the timekeeper core. W is
used for writing new time values. Users should be
certain not to load invalid values, such as FFh, to the
timekeeping registers. Updates to the timekeeping
core occur continuously except when locked.
Backup Power
The real-time clock/calendar is intended to be
permanently powered. When the primary system
power fails, the voltage on the VDD pin will drop.
When VDD is less 2.4V the RTC (and event counters)
will switch to the backup power supply on V BAK. The
clock operates at extremely low current in order to
maximize battery or capacitor life. However, an
advantage of combining a clock function with
F-RAM memory is that data is not lost regardless of
the backup power source.
The IBAK current varies with temperature and voltage
(see DC parametric table). The following graph
shows IBAK as a function of VBAK. These curves are
useful for calculating backup time when a capacitor
is used as the VBAK source.
Rev. 1.1
Apr. 2011
Figure 9. VBAK (min.) vs. Temperature
Trickle Charger
To facilitate capacitor backup, the VBAK pin can
optionally provide a trickle charge current. When the
VBC bit, register 0Bh bit 2, is set to „1‟ the VBAK pin
will source approximately 80µA until VBAK reaches
VDD or 3.75V whichever is less. In 3V systems, this
charges the capacitor to VDD without an external
diode and resistor charger. There is a Fast Charge
mode which is enabled by the FC bit (register 0Bh,
bit 5). In this mode the trickle charger current is set to
approximately 1 mA, allowing a large backup
capacitor to charge more quickly.
In the case where no battery is used, the VBAK pin
should be tied to VDD.
Although VBAK may be connected to VSS, this is not
recommended if the companion is used. None of
the companion functions will operate below
approximately 2.4V.
Page 7 of 26
FM31T372/374/376/378-G
Note: Systems using lithium batteries should clear the
VBC bit to ‘0’ to prevent battery charging. The VBAK
circuitry includes an internal 1 K series resistor as
a safety element.
32.768 kHz Clock Output
The 32.768 kHz clock (with precision equal to that of
the built-in crystal oscillator) can be output via the
FOUT pin. This output is not temperature
compensated. This clock can be disabled by clearing
the FOEN bit to „0‟.
/OSCEN
32.768 kHz
crystal
CF
Years
8 bits
Months
5 bits
32.768kHz
Clock
Divider
Oscillator
Date
6 bits
512 Hz
Hours
6 bits
1 Hz
Minutes
7 bits
W
Update
Logic
Seconds
7 bits
Days
3 bits
User Interface Registers
R
Figure 8. Real-Time Clock Core Block Diagram
Offset/Aging Compensation
The user can expect the RTC to be accurate from the
factory. The RTC is calibrated at the factory at room
temperature. The CAL bits setting in Register 01h
will likely be a non-zero value. This is the initial
calibration value assigned at the factory prior to
shipment. The device may need re-calibrating after
solder reflow or after some period of time due to
crystal aging.
If the user needs to re-calibrate the RTC, the
following describes the steps to change the
calibration setting. Before making changes to the
CAL bits, the user can read these bits to verify the
current setting is an expected value. To enter
calibration mode, the CAL bit in a register 00h must
be set to „1‟. When the RTC is in calibration mode,
the CAL/PFO output pin is dedicated to the
calibration function and the power fail output is
temporarily unavailable. Calibration operates by
applying a digital correction to the counter based on
the frequency error. In this mode, the CAL/PFO pin
is driven with a 512 Hz (nominal) square wave. Any
measured deviation from 512 Hz translates into a
Rev. 1.1
Apr. 2011
timekeeping error. The 512Hz calibration output
must be measured at +25°C. This output is not
temperature compensated. The user converts the
measured error in ppm and writes the appropriate
correction value to the calibration register. The
correction factors are listed in the following tables.
Positive ppm errors require a negative adjustment
that removes pulses. Negative ppm errors require a
positive correction that adds pulses. Positive ppm
adjustments have the CALS (sign) bit set to „1‟,
whereas negative ppm adjustments have CALS = 0.
The calibration setting is stored in F-RAM so is not
lost should the backup source fail. It is accessed with
bits CAL.5-0 in register 01h. This value only can be
written when the CAL bit is set to „1‟. To exit the
calibration mode, the user must clear the CAL bit to a
0. When the CAL bit is 0, the CAL/PFO pin will
revert to the power fail output function.
Note: Temperature compensation is disabled when
the CAL bit is set to ‘1’. The user should clear this bit
to allow temperature compensation to activate.
Page 8 of 26
FM31T372/374/376/378-G
Calibration Adjustments for Offset/Aging
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Rev. 1.1
Apr. 2011
Positive Calibration for Slow Measured Clocks
Measured Frequency Range at +25°C
Error Range (PPM)
Min
Max
Min
Max
Program Calibration Register to:
512.0000
511.9995
0.00
-1.02
1000000
511.9995
511.9984
-1.02
-3.05
1000001
511.9984
511.9974
-3.05
-5.09
1000010
511.9974
511.9964
-5.09
-7.12
1000011
511.9964
511.9953
-7.12
-9.16
1000100
511.9953
511.9943
-9.16
-11.19
1000101
511.9943
511.9932
-11.19
-13.22
1000110
511.9932
511.9922
-13.22
-15.26
1000111
511.9922
511.9911
-15.26
-17.29
1001000
511.9911
511.9901
-17.29
-19.33
1001001
511.9901
511.9891
-19.33
-21.36
1001010
511.9891
511.9880
-21.36
-23.40
1001011
511.9880
511.9870
-23.40
-25.43
1001100
511.9870
511.9859
-25.43
-27.47
1001101
511.9859
511.9849
-27.47
-29.50
1001110
511.9849
511.9839
-29.50
-31.53
1001111
511.9839
511.9828
-31.53
-33.57
1010000
511.9828
511.9818
-33.57
-35.60
1010001
511.9818
511.9807
-35.60
-37.64
1010010
511.9807
511.9797
-37.64
-39.67
1010011
511.9797
511.9786
-39.67
-41.71
1010100
511.9786
511.9776
-41.71
-43.74
1010101
511.9776
511.9766
-43.74
-45.78
1010110
511.9766
511.9755
-45.78
-47.81
1010111
511.9755
511.9745
-47.81
-49.85
1011000
511.9745
511.9734
-49.85
-51.88
1011001
511.9734
511.9724
-51.88
-53.91
1011010
511.9724
511.9714
-53.91
-55.95
1011011
511.9714
511.9703
-55.95
-57.98
1011100
511.9703
511.9693
-57.98
-60.02
1011101
511.9693
511.9682
-60.02
-62.05
1011110
511.9682
511.9672
-62.05
-64.09
1011111
511.9672
511.9661
-64.09
-66.12
1100000
511.9661
511.9651
-66.12
-68.16
1100001
511.9651
511.9641
-68.16
-70.19
1100010
511.9641
511.9630
-70.19
-72.22
1100011
511.9630
511.9620
-72.22
-74.26
1100100
511.9620
511.9609
-74.26
-76.29
1100101
511.9609
511.9599
-76.29
-78.33
1100110
511.9599
511.9589
-78.33
-80.36
1100111
511.9589
511.9578
-80.36
-82.40
1101000
511.9578
511.9568
-82.40
-84.43
1101001
511.9568
511.9557
-84.43
-86.47
1101010
511.9557
511.9547
-86.47
-88.50
1101011
511.9547
511.9536
-88.50
-90.54
1101100
511.9536
511.9526
-90.54
-92.57
1101101
511.9526
511.9516
-92.57
-94.60
1101110
511.9516
511.9505
-94.60
-96.64
1101111
511.9505
511.9495
-96.64
-98.67
1110000
511.9495
511.9484
-98.67
-100.71
1110001
511.9484
511.9474
-100.71
-102.74
1110010
511.9474
511.9464
-102.74
-104.78
1110011
511.9464
511.9453
-104.78
-106.81
1110100
511.9453
511.9443
-106.81
-108.85
1110101
511.9443
511.9432
-108.85
-110.88
1110110
511.9432
511.9422
-110.88
-112.92
1110111
511.9422
511.9411
-112.92
-114.95
1111000
511.9411
511.9401
-114.95
-116.98
1111001
511.9401
511.9391
-116.98
-119.02
1111010
511.9391
511.9380
-119.02
-121.05
1111011
511.9380
511.9370
-121.05
-123.09
1111100
511.9370
511.9359
-123.09
-125.12
1111101
511.9359
511.9349
-125.12
-127.16
1111110
511.9349
511.9339
-127.16
-129.19
1111111
Page 9 of 26
FM31T372/374/376/378-G
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Rev. 1.1
Apr. 2011
Negative Calibration for Fast Measured Clocks
Measured Frequency Range at +25°C
Error Range (PPM)
Min
Max
Min
Max
Program Calibration Register to:
512.0000
512.0005
0.00
1.02
0000000
512.0005
512.0016
1.02
3.05
0000001
512.0016
512.0026
3.05
5.09
0000010
512.0026
512.0036
5.09
7.12
0000011
512.0036
512.0047
7.12
9.16
0000100
512.0047
512.0057
9.16
11.19
0000101
512.0057
512.0068
11.19
13.22
0000110
512.0068
512.0078
13.22
15.26
0000111
512.0078
512.0089
15.26
17.29
0001000
512.0089
512.0099
17.29
19.33
0001001
512.0099
512.0109
19.33
21.36
0001010
512.0109
512.0120
21.36
23.40
0001011
512.0120
512.0130
23.40
25.43
0001100
512.0130
512.0141
25.43
27.47
0001101
512.0141
512.0151
27.47
29.50
0001110
512.0151
512.0161
29.50
31.53
0001111
512.0161
512.0172
31.53
33.57
0010000
512.0172
512.0182
33.57
35.60
0010001
512.0182
512.0193
35.60
37.64
0010010
512.0193
512.0203
37.64
39.67
0010011
512.0203
512.0214
39.67
41.71
0010100
512.0214
512.0224
41.71
43.74
0010101
512.0224
512.0234
43.74
45.78
0010110
512.0234
512.0245
45.78
47.81
0010111
512.0245
512.0255
47.81
49.85
0011000
512.0255
512.0266
49.85
51.88
0011001
512.0266
512.0276
51.88
53.91
0011010
512.0276
512.0286
53.91
55.95
0011011
512.0286
512.0297
55.95
57.98
0011100
512.0297
512.0307
57.98
60.02
0011101
512.0307
512.0318
60.02
62.05
0011110
512.0318
512.0328
62.05
64.09
0011111
512.0328
512.0339
64.09
66.12
0100000
512.0339
512.0349
66.12
68.16
0100001
512.0349
512.0359
68.16
70.19
0100010
512.0359
512.0370
70.19
72.22
0100011
512.0370
512.0380
72.22
74.26
0100100
512.0380
512.0391
74.26
76.29
0100101
512.0391
512.0401
76.29
78.33
0100110
512.0401
512.0411
78.33
80.36
0100111
512.0411
512.0422
80.36
82.40
0101000
512.0422
512.0432
82.40
84.43
0101001
512.0432
512.0443
84.43
86.47
0101010
512.0443
512.0453
86.47
88.50
0101011
512.0453
512.0464
88.50
90.54
0101100
512.0464
512.0474
90.54
92.57
0101101
512.0474
512.0484
92.57
94.60
0101110
512.0484
512.0495
94.60
96.64
0101111
512.0495
512.0505
96.64
98.67
0110000
512.0505
512.0516
98.67
100.71
0110001
512.0516
512.0526
100.71
102.74
0110010
512.0526
512.0536
102.74
104.78
0110011
512.0536
512.0547
104.78
106.81
0110100
512.0547
512.0557
106.81
108.85
0110101
512.0557
512.0568
108.85
110.88
0110110
512.0568
512.0578
110.88
112.92
0110111
512.0578
512.0589
112.92
114.95
0111000
512.0589
512.0599
114.95
116.98
0111001
512.0599
512.0609
116.98
119.02
0111010
512.0609
512.0620
119.02
121.05
0111011
512.0620
512.0630
121.05
123.09
0111100
512.0630
512.0641
123.09
125.12
0111101
512.0641
512.0651
125.12
127.16
0111110
512.0651
512.0661
127.16
129.19
0111111
Page 10 of 26
FM31T372/374/376/378-G
Register Map
The TCXO and processor companion functions are accessed via 25 special function registers mapped to a separate
2-wire device ID. The interface protocol is described below. The registers contain timekeeping data, control bits, or
information flags. A description of each register follows the summary table below.
Register Map Summary Table
Nonvolatile =
Battery-backed =
Address
18h
17h
16h
15h
14h
13h
12h
11h
10h
0Fh
0Eh
0Dh
0Ch
0Bh
0Ah
09h
08h
07h
06h
05h
04h
03h
02h
01h
00h
D7
SNL
WDE
W TR
0
0
0
0
0
0
/OSCEN
reserved
D6
Data
D5
D4
D3
Serial Number Byte 7
Serial Number Byte 6
Serial Number Byte 5
Serial Number Byte 4
Serial Number Byte 3
Serial Number Byte 2
Serial Number Byte 1
Serial Number Byte 0
Counter 2 MSB
Counter 2 LSB
Counter 1 MSB
Counter 1 LSB
RC
FC
WP1
WP0
WDT4
W DT3
LB
WR3
FOEN
POR
10 years
0
0
10 mo
0
10 date
0
0
0
0
10 hours
10 minutes
10 seconds
CALS
CAL5
CAL4
CF
reserved reserved
D2
0
CAL3
reserved
D1
CC
C2P
VBC
VTP1
WDT2
WDT1
WR2
WR1
years
months
date
day
hours
minutes
seconds
CAL2
CAL1
CAL
W
D0
C1P
VTP0
WDT0
WR0
CAL0
R
Function
Serial Number 7
Serial Number 6
Serial Number 5
Serial Number 4
Serial Number 3
Serial Number 2
Serial Number 1
Serial Number 0
Event Counter 2 MSB
Event Counter 2 LSB
Event Counter 1 MSB
Event Counter 1 LSB
Event Count Control
Companion Control
Watchdog Control
Watchdog Restart/Flags
Years
Month
Date
Day
Hours
Minutes
Seconds
OSC/CAL Control
RTC Control
Range
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
00-99
1-12
1-31
1-7
0-23
0-59
0-59
Note: When the device is first powered up and programmed, all registers must be written because the
battery-backed register values cannot be guaranteed. The table below shows the default values of the non-volatile
registers. All other register values should be treated as unknown.
Default Register Values
Address
18h
17h
16h
15h
14h
13h
12h
11h
0Bh
0Ah
01h
Rev. 1.1
Apr. 2011
Hex Value
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x40
0x1F
Factory
programmed
Page 11 of 26
FM31T372/374/376/378-G
Register Description
Address Description
18h
Serial Number Byte 7
D7
D6
D5
D4
D3
D2
D1
D0
SN.63
SN.62
SN.61
SN.60
SN.59
SN.58
SN.57
SN.56
Upper byte of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
17h
Serial Number Byte 6
D7
D6
D5
D4
D3
D2
D1
D0
SN.55
SN.54
SN.53
SN.52
SN.51
SN.50
SN.49
SN.48
Byte 6 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
16h
Serial Number Byte 5
D7
D6
D5
D4
D3
D2
D1
D0
SN.47
SN.46
SN.45
SN.44
SN.43
SN.42
SN.41
SN.40
Byte 5 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
15h
Serial Number Byte 4
D7
D6
D5
D4
D3
D2
D1
D0
SN.39
SN.38
SN.37
SN.36
SN.35
SN.34
SN.33
SN.32
Byte 4 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
14h
Serial Number Byte 3
D7
D6
D5
D4
D3
D2
D1
D0
SN.31
SN.30
SN.29
SN.28
SN.27
SN.26
SN.25
SN.24
Byte 3 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
13h
Serial Number Byte 2
D7
D6
D5
D4
D3
D2
D1
D0
SN.23
SN.22
SN.21
SN.20
SN.19
SN.18
SN.17
SN.16
Byte 2 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
12h
Serial Number Byte 1
D7
D6
D5
D4
D3
D2
D1
D0
SN.15
SN.14
SN.13
SN.12
SN.11
SN.10
SN.9
SN.8
Byte 1 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
11h
Serial Number Byte 0
D7
D6
D5
D4
D3
D2
D1
D0
SN.7
SN.6
SN.5
SN.4
SN.3
SN.2
SN.1
SN.0
LSB of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
10h
Counter 2 MSB
D7
D6
D5
D4
D3
D2
D1
D0
C2.15
C2.14
C2.13
C2.12
C2.11
C2.10
C2.9
C2.8
Event Counter 2 MSB. Increments on overflows from Counter 2 LSB. Battery-backed, read/write.
0Fh
Counter 2 LSB
D7
D6
D5
D4
D3
D2
D1
D0
C2.7
C2.6
C2.5
C2.4
C2.3
C2.2
C2.1
C2.0
Event Counter 2 LSB. Increments on programmed edge event on CNT2 input or overflows from Counter 1 MSB
when CC=1. Battery-backed, read/write .
0Eh
Counter 1 MSB
D7
D6
D5
D4
D3
D2
D1
D0
C1.15
C1.14
C1.13
C1.12
C1.11
C1.10
C1.9
C1.8
Event Counter 1 MSB. Increments on overflows from Counter 1 LSB. Battery-backed, read/write.
0Dh
Counter 1 LSB
D7
D6
D5
D4
D3
D2
D1
D0
C1.7
C1.6
C1.5
C1.4
C1.3
C1.2
C1.1
C1.0
Event Counter 1 LSB. Increments on programmed edge event on CNT1 input. Battery-backed, read/write.
Rev. 1.1
Apr. 2011
Page 12 of 26
FM31T372/374/376/378-G
0Ch
RC
CC
C2P
C1P
0Bh
SNL
FOEN
FC
WP1-0
Event Counter Control
D7
D6
D5
D4
D3
D2
D1
D0
-
-
-
-
RC
CC
C2P
C1P
Read Counter. Setting this bit to 1 takes a snapshot of the four counters bytes allowing the system to read the
values without missing count events. The RC bit will be automatically cleared.
Counter Cascade. When CC=0, the event counters operate independently according to the edge programmed by
C1P and C2P respectively. When CC=1, the counters are cascaded to create one 32-bit counter. The registers of
Counter 2 represent the most significant 16-bits of the counter and CNT1 is the controlling input. Bit C2P is
“don‟t care” when CC=1. Battery-backed, read/write.
CNT2 detects falling edges when C2P = 0, rising edges when C2P = 1. C2P is “don‟t care” when CC=1. The value
of Event Counter 2 may inadvertently increment if C2P is changed. Battery-backed, read/write.
CNT1 detects falling edges when C1P = 0, rising edges when C1P = 1. The value of Event Counter 1 may
inadvertently increment if C1P is changed. Battery-backed, read/write.
Companion Control
D7
D6
D5
D4
D3
D2
D1
D0
SNL
FOEN
FC
WP1
WP0
VBC
VTP1
VTP0
Serial Number Lock. Setting to a 1 makes registers 11h to 18h and SNL permanently read-only. SNL cannot be
cleared once set to 1. Nonvolatile, read/write.
32.768kHz Frequency Output Enable. Default is 1 = “On”. Output FOUT turned off when FOEN = 0.
Temperature compensation is not applied to the 32.768kHz frequency on the FOUT pin.
Fast Charge: Setting FC to „1‟ (and VBC=1) causes a ~1 mA trickle charge current to be supplied on V BAK.
Clearing VBC to „0‟ disables the charge current. Nonvolatile, read/write.
Write Protect. These bits control the write protection of the memory array. Nonvolatile, read/write.
Write protect addresses
None
Bottom ¼
Bottom ½
Full array
VBC
WP1 WP0
0
0
0
1
1
0
1
1
VTP1-0
VBAK Charger Control. Setting VBC to 1 causes ~80 µA (FC=0) trickle charge current to be supplied on VBAK.
Clearing VBC to 0 disables the charge current. Nonvolatile, read/write.
VTP select. These bits control the reset trip point for the low VDD reset function. Nonvolatile, read/write.
0Ah
VTP
2.6V
2.9V
3.9V
4.4V
Watchdog Control
WDE
WDT4-0
VTP1 VTP0
0 0
0 1
1 0
1 1
D7
D6
D5
D4
D3
D2
D1
D0
WDE
-
-
WDT4
WDT3
WDT2
WDT1
WDT0
Watchdog Enable. When WDE=1, a watchdog timer fault will cause the /RST signal to go active. When WDE = 0
the timer runs but has no effect on /RST, however the WTR flag will be set when a fault occurs. Note as the timer
is free-running, users should restart the timer using WR3-0 prior to setting WDE=1. This assures a full watchdog
timeout interval occurs. Nonvolatile, read/write.
Watchdog Timeout. Indicates the minimum watchdog timeout interval with 100 ms resolution. New watchdog
timeouts are loaded when the timer is restarted by writing the 1010b pattern to WR3-0. Nonvolatile, read/write.
Watchdog timeout
Invalid – default 100 ms
100 ms
200 ms
300 ms
.
.
.
2000 ms
2100 ms
2200 ms
.
Rev. 1.1
Apr. 2011
WDT4 WDT3 WDT2 WDT1 WDT0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
1
1
1
1
1
0
0
0
1
1
1
0
0
1
0
1
0
Page 13 of 26
FM31T372/374/376/378-G
09h
WTR
POR
LB
WR3-0
08h
.
.
2900 ms
3000 ms
Disable counter
Watchdog Restart & Flags
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
D7
D6
D5
D4
D3
D2
D1
D0
WTR
POR
LB
-
WR3
WR2
WR1
WR0
Watchdog Timer Reset Flag: When a watchdog timer fault occurs, the WTR bit will be set to 1. It must be cleared
by the user. Note that both WTR and POR could be set if both reset sources have occurred since the flags were
cleared by the user. Battery-backed. Read/Write (internally set, user can clear bit).
Power-on Reset Flag: When the /RST pin is activated by a VDD < VTP condition, the POR bit will be set to 1. It
must be cleared by the user. Note that both WTR and POR could be set if the reset source has occurred since the
flags were cleared by the user. Battery-backed. Read/Write (internally set, user can clear bit).
Low Backup Flag: On power up, if the VBAK source is below the minimum voltage to operate the RTC and event
counters, this bit will be set to 1. The user should clear it to 0 when initializing the system. Battery-backed.
Read/Write (internally set, user can clear bit).
Watchdog Restart: Writing a pattern 1010b to WR3-0 restarts the watchdog timer. The upper nibble contents do
not affect this operation. Writing any pattern other than 1010b to WR3-0 has no effect on the timer. This allows
users to clear the WTR, POR, and LB flags without affecting the watchdog timer. Battery-backed, Write-only.
Timekeeping – Years
D7
D6
D5
D4
D3
D2
D1
D0
10 year.3
10 year.2
10 year.1
10 year.0
Year.3
Year.2
Year.1
Year.0
Contains the lower two BCD digits of the year. Lower nibble contains the value for years; upper nibble contains
the value for 10s of years. Each nibble operates from 0 to 9. The range for the register is 0-99. Battery-backed,
read/write.
07h
Timekeeping – Months
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
10 Month
Month.3
Month.2
Month.1
Month.0
Contains the BCD digits for the month. Lower nibble contains the lower digit and operates from 0 to 9; upper
nibble (one bit) contains the upper digit and operates from 0 to 1. The range for the register is 1-12.
Battery-backed, read/write.
06h
Timekeeping – Date of the month
D7
D6
D5
D4
D3
D2
D1
D0
0
0
10 date.1
10 date.0
Date.3
Date.2
Date.1
Date.0
Contains the BCD digits for the date of the month. Lower nibble contains the lower digit and operates from 0 to 9;
upper nibble contains the upper digit and operates from 0 to 3. The range for the register is 1-31. Battery-backed,
read/write.
05h
Timekeeping – Day of the week
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
Day.2
Day.1
Day.0
Lower nibble contains a value that correlates to day of the week. Day of the week is a ring counter that counts
from 1 to 7 then returns to 1. The user must assign meaning to the day value, as the day is not integrated with the
date. Battery-backed, read/write.
04h
Timekeeping – Hours
D7
D6
D5
D4
D3
D2
D1
D0
0
0
10 hours.1
10 hours.0
Hours.3
Hours2
Hours.1
Hours.0
Contains the BCD value of hours in 24-hour format. Lower nibble contains the lower digit and operates from 0 to
9; upper nibble (two bits) contains the upper digit and operates from 0 to 2. The range for the register is 0-23.
Battery-backed, read/write.
03h
Timekeeping – Minutes
D7
D6
D5
D4
D3
D2
D1
D0
0
10 min.2
10 min.1
10 min.0
Min.3
Min.2
Min.1
Min.0
Contains the BCD value of minutes. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble
contains the upper minutes digit and operates from 0 to 5. The range for the register is 0-59. Battery-backed,
read/write.
Rev. 1.1
Apr. 2011
Page 14 of 26
FM31T372/374/376/378-G
02h
Timekeeping – Seconds
D7
D6
D5
D4
D3
D2
D1
D0
0
10 sec.2
10 sec.1
10 sec.0
Seconds.3
Seconds.2
Seconds.1
Seconds.0
Contains the BCD value of seconds. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble
contains the upper digit and operates from 0 to 5. The range for the register is 0-59. Battery-backed, read/write.
01h
/OSCEN
OSC/Control
D7
D6
D5
D4
D3
D2
D1
D0
OSCEN
CALS
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
CAL.5-0
/Oscillator Enable. When set to 1, the oscillator is halted. When set to 0, the oscillator runs. Disabling the
oscillator can save battery power during storage. On a power-up without battery, this bit is set to 1.
Battery-backed, read/write.
Calibration sign. Determines if the calibration adjustment is applied as an addition to or as a subtraction from
the time-base. Calibration is explained on page 8. This bit is factory programmed. Nonvolatile, read/write.
These six bits control the calibration of the clock. These bits are factory programmed. Nonvolatile, read/write.
00h
Flags/Control
CALS
Reserved
CF
CAL
W
R
Rev. 1.1
Apr. 2011
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
CF
Reserved
Reserved
Reserved
CAL
W
R
Reserved bits. Do not use. Should remain set to 0.
Century Overflow Flag. This bit is set to a 1 when the values in the years register overflows from 99 to 00. This
indicates a new century, such as going from 1999 to 2000 or 2099 to 2100. The user should record the new
century information as needed. This bit is cleared to 0 when the Flag register is read. It is read-only for the user.
Battery-backed.
When set to 1, the CAL/PFO pin gives a 512 Hz square-wave output for clock audit. When CAL bit set to 0,
the clock operates normally, and the CAL/PFO pin is controlled by the power fail comparator. The CAL bit
must be cleared to enable temperature compensation. Temperature compensation is not applied to the 512Hz
frequency on the CAL/PFO pin. Battery-backed, read/write.
Write Time. Setting the W bit to 1 freezes the clock. The user can then write the timekeeping registers with
updated values. Resetting the W bit to 0 causes the contents of the time registers to be transferred to the
timekeeping counters and restarts the clock. Battery-backed, read/write.
Read Time. Setting the R bit to 1 copies a static image of the timekeeping core and place it into the user
registers. The user can then read them without concerns over changing values causing system errors. The R bit
going from 0 to 1 causes the timekeeping capture, so the bit must be returned to 0 prior to reading again.
Battery-backed, read/write.
Page 15 of 26
FM31T372/374/376/378-G
By convention, any device that is sending data onto
the bus is the transmitter while the target device for
this data is the receiver. The device that is
controlling the bus is the master. The master is
responsible for generating the clock signal for all
operations. Any device on the bus that is being
controlled is a slave. The FM31T37x is always a
slave device.
Two-wire Interface
The FM31T37x employs an industry standard
two-wire bus that is familiar to many users. This
product is unique since it incorporates two logical
devices in one chip. Each logical device can be
accessed individually. Although monolithic, it
appears to the system software to be two separate
products. One is a memory device. It has a Slave
Address (Slave ID = 1010b) that operates the same
as a stand-alone memory device. The second device
is a real-time clock and processor companion which
have a unique Slave Address (Slave ID = 1101b).
The bus protocol is controlled by transition states in
the SDA and SCL signals. There are four conditions:
Start, Stop, Data bit, and Acknowledge. The figure
below illustrates the signal conditions that specify
the four states. Detailed timing diagrams are shown
in the Electrical Specifications section.
SCL
7
SDA
Stop
(Master)
Start
(Master)
Figure 9.
Data bits
(Transmitter)
0
Data bit Acknowledge
(Transmitter) (Receiver)
Data Transfer Protocol
Start Condition
A Start condition is indicated when the bus master
drives SDA from high to low while the SCL signal is
high. All read and write transactions begin with a
Start condition. An operation in progress can be
aborted by asserting a Start condition at any time.
Aborting an operation using the Start condition will
ready the FM31T37x for a new operation.
If the power supply drops below the specified VTP
during operation, any 2-wire transaction in progress
will be aborted and the system must issue a Start
condition prior to performing another operation.
Stop Condition
A Stop condition is indicated when the bus master
drives SDA from low to high while the SCL signal is
high. All operations must end with a Stop condition.
If an operation is pending when a stop is asserted,
the operation will be aborted. The master must have
control of SDA (not a memory read) in order to
assert a Stop condition.
Data/Address Transfer
All data transfers (including addresses) take place
while the SCL signal is high. Except under the two
Rev. 1.1
Apr. 2011
6
conditions described above, the SDA signal should
not change while SCL is high.
Acknowledge
The Acknowledge (ACK) takes place after the 8th
data bit has been transferred in any transaction.
During this state the transmitter must release the
SDA bus to allow the receiver to drive it. The
receiver drives the SDA signal low to acknowledge
receipt of the byte. If the receiver does not drive
SDA low, the condition is a No-Acknowledge
(NACK) and the operation is aborted.
The receiver might NACK for two distinct reasons.
First is that a byte transfer fails. In this case, the
NACK ends the current operation so that the part can
be addressed again. This allows the last byte to be
recovered in the event of a communication error.
Second and most common, the receiver does not
send an ACK to deliberately terminate an operation.
For example, during a read operation, the FM31T37x
will continue to place data onto the bus as long as the
receiver sends ACKs (and clocks). When a read
operation is complete and no more data is needed,
the receiver must NACK the last byte. If the receiver
ACKs the last byte, this will cause the FM31T37x to
Page 16 of 26
FM31T372/374/376/378-G
attempt to drive the bus on the next clock while the
master is sending a new command such as a Stop.
Slave Address
The first byte that the FM31T37x expects after a
Start condition is the slave address. As shown in
figures below, the slave address contains the Slave
ID, Device Select address, and a bit that specifies if
the transaction is a read or a write.
The FM31T37x has two Slave Addresses (Slave IDs)
associated with two logical devices. To access the
memory device, bits 7-4 should be set to 1010b. The
other logical device within the FM31T37x is the
real-time clock and companion. To access this
device, bits 7-4 of the slave address should be set to
1101b. A bus transaction with this slave address
will not affect the memory in any way. The figures
below illustrate the two Slave Addresses.
The Device Select bits allow multiple devices of the
same type to reside on the 2-wire bus. The device
select bits (bits 2-1) select one of four parts on a
two-wire bus. They must match the corresponding
value on the external address pins in order to select
the device. Bit 0 is the read/write bit. A “1” indicates
a read operation, and a “0” indicates a write
operation.
Device
Select
Slave ID
1
7
0
1
6
5
Figure 10.
0
X
A1
A0
R/W
4
3
2
1
0
Slave Address - Memory
Device
Select
Slave ID
1
7
1
0
6
5
Figure 11.
1
X
A1
A0
R/W
4
3
2
1
0
Slave Address – Companion
Addressing Overview – Memory
After the FM31T37x acknowledges the Slave
Address, the master can place the memory address
on the bus for a write operation. The address requires
two bytes. This is true for all members of the family.
Therefore the 4Kb and 16Kb configurations will be
addressed differently from stand alone serial
memories but the entire family will be upwardly
compatible with no software changes.
Rev. 1.1
Apr. 2011
The first is the MSB (upper byte). For a given
density unused address bits are don‟t cares, but
should be set to 0 to maintain upward compatibility.
Following the MSB is the LSB (lower byte) which
contains the remaining eight address bits. The
address is latched internally. Each access causes the
latched address to be incremented automatically. The
current address is the value that is held in the latch,
either a newly written value or the address following
the last access. The current address will be held as
long as VDD > VTP or until a new value is written.
Accesses to the clock do not affect the current
memory address. Reads always use the current
address. A random read address can be loaded by
beginning a write operation as explained below.
After transmission of each data byte, just prior to the
Acknowledge, the FM31T37x increments the
internal address. This allows the next sequential byte
to be accessed with no additional addressing
externally. After the last address is reached, the
address latch will roll over to 0000h. There is no
limit to the number of bytes that can be accessed
with a single read or write operation.
Addressing Overview – RTC & Companion
The RTC and Processor Companion operate in a
similar manner to the memory, except that it uses
only one byte of address. Addresses 00h to 18h
correspond to special function registers. Attempting
to load addresses above 18h is an illegal condition;
the FM31 xxT37x will return a NACK and abort the
2-wire transaction.
Data Transfer
After the address information has been transmitted,
data transfer between the bus master and the
FM31T37x begins. For a read, the FM31T37x will
place 8 data bits on the bus then wait for an ACK
from the master. If the ACK occurs, the FM31T37x
will transfer the next byte. If the ACK is not sent, the
FM31T37x will end the read operation. For a write
operation, the FM31T37x will accept 8 data bits
from the master then send an Acknowledge. All data
transfer occurs MSB (most significant bit) first.
Memory Write Operation
All memory writes begin with a Slave Address, then
a memory address. The bus master indicates a write
operation by setting the slave address LSB to a 0.
After addressing, the bus master sends each byte of
data to the memory and the memory generates an
Acknowledge condition. Any number of sequential
bytes may be written. If the end of the address range
Page 17 of 26
FM31T372/374/376/378-G
is reached internally, the address counter will wrap
to 0000h. Internally, the actual memory write occurs
after the 8th data bit is transferred. It will be complete
before the Acknowledge is sent. Therefore, if the
user desires to abort a write without altering the
Start
By Master
S
memory contents, this should be done using a Start
or Stop condition prior to the 8th data bit. The figures
below illustrate a single- and multiple-writes to
memory.
Stop
Address & Data
Slave Address
0 A
Address MSB
A
Address LSB
A
Data Byte
A
P
ByFM31T37x
FM31xxx
By
Acknowledge
Figure 12.
Single Byte Memory Write
Start
S
FM31xxx
ByBy
FM31T37x
Stop
Address & Data
By Master
Slave Address
0 A
Address MSB
A
Address LSB
A
Data Byte
A
Data Byte
A
P
Acknowledge
Figure 13. Multiple Byte Memory Write
Memory Read Operation
There are two types of memory read operations. They
are current address read and selective address read. In
a current address read, the FM31T37x uses the
internal address latch to supply the address. In a
selective read, the user performs a procedure to first
set the address to a specific value.
Current Address & Sequential Read
As mentioned above the FM31T37x uses an internal
latch to supply the address for a read operation. A
current address read uses the existing value in the
address latch as a starting place for the read
operation. The system reads from the address
immediately following that of the last operation.
To perform a current address read, the bus master
supplies a slave address with the LSB set to 1. This
indicates that a read operation is requested. After
receiving the complete device address, the
FM31T37x will begin shifting data out from the
current address on the next clock. The current address
is the value held in the internal address latch.
Beginning with the current address, the bus master
can read any number of bytes. Thus, a sequential read
is simply a current address read with multiple byte
Rev. 1.1
Apr. 2011
transfers. After each byte the internal address counter
will be incremented.
Each time the bus master acknowledges a byte,
this indicates that the FM31T37x should read
out the next sequential byte.
There are four ways to terminate a read operation.
Failing to properly terminate the read will most likely
create a bus contention as the FM31T37x attempts to
read out additional data onto the bus. The four valid
methods follow.
1.
2.
3.
4.
The bus master issues a NACK in the 9th clock
cycle and a Stop in the 10th clock cycle. This is
illustrated in the diagrams below and is
preferred.
The bus master issues a NACK in the 9th clock
cycle and a Start in the 10th.
The bus master issues a Stop in the 9th clock
cycle.
The bus master issues a Start in the 9th clock
cycle.
If the internal address reaches the top of memory, it
will wrap around to 0000h on the next read cycle.
The figures below show the proper operation for
current address reads.
Page 18 of 26
FM31T372/374/376/378-G
Selective (Random) Read
There is a simple technique that allows a user to
select a random address location as the starting point
for a read operation. This involves using the first
three bytes of a write operation to set the internal
address followed by subsequent read operations.
RTC/Companion Read Operation
As with writes, a read operation begins with the
Slave Address. To perform a register read, the bus
master supplies a Slave Address with the LSB set to
1. This indicates that a read operation is requested.
After receiving the complete Slave Address, the
FM31T37x will begin shifting data out from the
current register address on the next clock.
Auto-increment operates for the special function
registers as with the memory address. A current
address read for the registers look exactly like the
memory except that the device ID is different.
To perform a selective read, the bus master sends out
the slave address with the LSB set to 0. This specifies
a write operation. According to the write protocol,
the bus master then sends the address bytes that are
loaded into the internal address latch. After the
FM31T37x acknowledges the address, the bus master
issues a Start condition. This simultaneously aborts
the write operation and allows the read command to
be issued with the slave address LSB set to a 1. The
operation is now a read from the current address.
Read operations are illustrated below.
The FM31T37x contains two separate address
registers, one for the memory address and the other
for the register address. This allows the contents of
one address register to be modified without affecting
the current address of the other register. For example,
this would allow an interrupted read to the memory
while still providing fast access to an RTC register. A
subsequent memory read will then continue from the
memory address where it previously left off, without
requiring the load of a new memory address.
However, a write sequence always requires an
address to be supplied.
RTC /Companion Write Operation
All RTC and Companion writes operate in a similar
manner to memory writes. The distinction is that a
different device ID is used and only one byte address
is needed instead of two. Figure 16 illustrates a single
byte write to this device.
By Master
Start
No
Acknowledge
Address
Stop
S
Slave Address
ByBy
FM31T37x
FM31xxx
1 A
Acknowledge
Data Byte
1
P
Data
Figure 14. Current Address Memory Read
By Master
Start
Slave Address
1 A
Data Byte
Acknowledge
Figure 15.
Rev. 1.1
Apr. 2011
No
Acknowledge
Acknowledge
Stop
S
FM31xxx
ByByFM31T37x
Address
A
Data Byte
1 P
Data
Sequential Memory Read
Page 19 of 26
FM31T372/374/376/378-G
Start
Address
By Master
Start
No
Acknowledge
Address
Stop
S
Slave Address
0 A
Address MSB
A
Address LSB
ByFM31T37x
FM31xxx
By
A
S
Slave Address
1 A
Data Byte
Data
Acknowledge
Figure 16.
By Master
Selective (Random) Memory Read
Address & Data
Start
S
Slave Address
0 A 0 0 0
Address
By FM31T37x
Stop
A
Data Byte
A
P
Acknowledge
Figure 17.
NOTE:
1 P
Byte Register Write
It is required that Register Address bits A7-A5 are cleared (zeroes).
Addressing F-RAM Array in the FM31T37x Family
The FM31T37x family includes 256Kb, 64Kb, 16Kb, and 4Kb memory densities. The following 2-byte address field
is shown for each density.
Table 4.
Part #
Two-Byte Memory Address
1st Address Byte
FM31T378
FM31T376
FM31T374
FM31T372
Rev. 1.1
Apr. 2011
x
x
x
x
A14
x
x
x
A13
x
x
x
A12
A12
x
x
A11
A11
x
x
2nd Address Byte
A10
A10
A10
x
A9
A9
A9
x
A8
A8
A8
A8
A7
A7
A7
A7
A6
A6
A6
A6
A5
A5
A5
A5
A4
A4
A4
A4
A3
A3
A3
A3
A2
A2
A2
A2
A1
A1
A1
A1
A0
A0
A0
A0
Page 20 of 26
FM31T372/374/376/378-G
Electrical Specifications
Absolute Maximum Ratings
Symbol
Description
VDD
Power Supply Voltage with respect to VSS
VIN
Voltage on any signal pin with respect to VSS
VBAK
TSTG
TLEAD
VESD
Backup Supply Voltage
Storage Temperature
Lead Temperature (Soldering, 10 seconds)
Electrostatic Discharge Voltage
- Human Body Model (AEC-Q100-002 Rev. E)
- Charged Device Model (AEC-Q100-011 Rev. B)
- Machine Model (AEC-Q100-003 Rev. E)
Package Moisture Sensitivity Level
Ratings
-1.0V to +7.0V
-1.0V to +7.0V and
VIN ≤ VDD+1.0V *
-1.0V to +4.5V
-55C to + 125C
260 C
2kV
1.25kV
100V
MSL-1
* The “VIN < VDD+1.0V” restriction does not apply to the SCL and SDA inputs which do not employ a diode to V DD.
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only,
and the functional operation of the device at these or any other conditions above those listed in the operational section of this
specification is not implied. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability.
DC Operating Conditions (TA = -40 C to + 85 C, VDD = 2.7V to 5.5V unless otherwise specified)
Symbol
Parameter
Min
Typ
Max
VDD
Main Power Supply
2.7
5.5
IDD
VDD Supply Current
@ SCL = 100 kHz
500
@ SCL = 400 kHz
900
@ SCL = 1 MHz
1500
ISB
Standby Current
For VDD < 5.5V
150
For VDD < 3.6V
120
VBAK
RTC Backup Supply Voltage
@ TA = +25ºC to +85ºC
1.55
3.75
@ TA = -40ºC to +25ºC
1.9
3.75
IBAK
RTC Backup Supply Current
@ TA = +25ºC, VBAK = 3.0V
1.4
@ TA = +85ºC, VBAK = 3.0V
2.1
@ TA = +25ºC, VBAK = 2.0V
1.15
@ TA = +85ºC, VBAK = 2.0V
1.75
IBAKTC
Trickle Charge Current with VBAK=0V
Fast Charge Off (FC = 0)
50
120
Fast Charge On (FC = 1)
200
2500
VTP0
VDD Trip Point Voltage, VTP(1:0) = 00b
2.55
2.6
2.70
VTP1
VDD Trip Point Voltage, VTP(1:0) = 01b
2.80
2.9
3.00
VTP2
VDD Trip Point Voltage, VTP(1:0) = 10b
3.80
3.9
4.00
VTP3
VDD Trip Point Voltage, VTP(1:0) = 11b
4.25
4.4
4.50
VRST
VDD for valid /RST @ IOL = 80 A at VOL
0
VBAK > VBAK min
1.6
VBAK < VBAK min
ILI
Input Leakage Current
1
ILO
Output Leakage Current
1
VIL
Input Low Voltage
All inputs except those listed below
-0.3
0.3 VDD
CNT1-2 battery backed (VDD < 2.4V)
-0.3
0.5
CNT1-2 (VDD > 2.4V)
-0.3
0.8
continued
Rev. 1.1
Apr. 2011
Units
V
A
A
A
A
A
V
V
V
A
A
A
A
A
A
V
V
V
V
V
V
A
A
V
V
V
Notes
7
1
2
9
4
10
5
5
5
5
6
3
3
8
»
Page 21 of 26
FM31T372/374/376/378-G
DC Operating Conditions, continued (TA = -40 C to + 85 C, VDD = 2.7V to 5.5V unless otherwise specified)
Symbol Parameter
Min
Typ
Max
Units
VIH
Input High Voltage
All inputs except those listed below
0.7 VDD
VDD + 0.3
V
PFI (comparator input)
3.75
V
CNT1-2 battery backed (VDD < 2.4V)
VBAK – 0.5
VBAK + 0.3
V
CNT1-2 VDD > 2.4V
0.7 VDD
VDD + 0.3
V
VOL
Output Low Voltage (IOL = 3 mA),
0.4
V
FOUT, /INT, /RST
VOH
Output High Voltage (IOH = -2 mA)
2.4
V
RRST
Pull-up Resistance for /RST Inactive
50
400
K
RIN
Input Resistance (pulldown)
A1-A0 for VIN = VIL max
20
K
A1-A0 for VIN = VIH min
1
M
VPFI
Power Fail Input Reference Voltage
1.175
1.20
1.225
V
VHYS
Power Fail Input (PFI) Hysteresis (Rising)
100
mV
Notes
Notes
1. SCL toggling between VDD-0.3V and VSS, other inputs VSS or VDD-0.3V.
2. All inputs at VSS or VDD, static. Stop command issued.
3. VIN or VOUT = VSS to VDD. Does not apply to A0, A1, PFI, or /RST pins.
4. VBAK = 3.0V, VDD < 2.4V, oscillator running, CNT1-2 at Vss or VBAK.
5. /RST is asserted low when VDD < VTP.
6. The minimum VDD to guarantee the level of /RST remains a valid V OL level.
7. Full complete operation. Supervisory circuits, RTC, etc operate to lower voltages as specified.
8. Includes /RST input detection of external reset condition to trigger driving of /RST signal by FM31T37x.
9. The VBAK trickle charger automatically regulates the maximum voltage on this pin for capacitor backup applications.
10. VBAK will source current when trickle charge is enabled (VBC bit=1), V DD > VBAK, and VBAK < VBAK max.
AC Parameters (TA = -40 C to + 85 C, VDD = 2.7V to 5.5V, CL = 100 pF unless otherwise specified)
Symbol Parameter
Min Max Min Max Min Max
fSCL
SCL Clock Frequency
0
100
0
400
0
1000
tLOW
Clock Low Period
4.7
1.3
0.6
tHIGH
Clock High Period
4.0
0.6
0.4
tAA
SCL Low to SDA Data Out Valid
3
0.9
0.55
tBUF
tHD:STA
tSU:STA
tHD:DAT
tSU:DAT
tR
tF
tSU:STO
tDH
tSP
Bus Free Before New Transmission
Start Condition Hold Time
Start Condition Setup for Repeated
Start
Data In Hold Time
Data In Setup Time
Input Rise Time
Input Fall Time
Stop Condition Setup Time
Data Output Hold (from SCL @ VIL)
Noise Suppression Time Constant
on SCL, SDA
Units
kHz
s
s
s
4.7
4.0
4.7
1.3
0.6
0.6
0.5
0.25
0.25
s
s
s
0
250
0
100
0
100
ns
ns
ns
ns
s
ns
ns
1000
300
4.0
0
300
300
0.6
0
50
300
100
0.25
0
50
50
Notes
1
1
All SCL specifications as well as start and stop conditions apply to both read and write operations.
RTC Frequency Characteristics
Symbol Parameter
FOUT
FOUT Clock Frequency
Frequency Stability
0 C to +45 C
Δf/f
vs. Temperature
-40 C to +85 C
Rev. 1.1
Apr. 2011
Min
-
Typ
32.768
Max
±3
±5
Units
kHz
ppm
ppm
Page 22 of 26
FM31T372/374/376/378-G
Data Retention (TA = -40 C to + 85 C, VDD = 2.7V to 5.5V)
Symbol
Parameter
TDR
Data Retention
Min
10
Supervisor Timing (TA = -40 C to + 85 C, VDD = 2.7V to 5.5V)
Symbol
Parameter
tRPU
/RST Active (low) after VDD>VTP
tINTP
Pulse Width of /INT Active
tRNR
VDD < VTP noise immunity
tVR
VDD Rise Time
tVF
VDD Fall Time
tWDP
Pulse Width of /RST for Watchdog Reset
tWDOG
Timeout of Watchdog
fCNT
Frequency of Event Counters
Min
100
100
10
50
100
100
tDOG
0
Units
Years
Max
200
200
25
200
2*tDOG
10
Notes
Units
ms
ms
s
s/V
s/V
ms
ms
MHz
Notes
1
1,2
1,2
3
Notes
1
This parameter is characterized but not tested.
2
Slope measured at any point on VDD waveform.
3
tDOG is the programmed time in register 0Ah, V DD > VTP and tRPU satisfied.
/RST Timing
VDD
VTP
VRST
t RNR
t RPU
RST
/INT Pulse Width
CNT1,
CNT2
tINTP
INT
Rev. 1.1
Apr. 2011
Page 23 of 26
FM31T372/374/376/378-G
AC Test Conditions
Equivalent AC Load Circuit
Input Pulse Levels
Input rise and fall times
Input and output timing levels
5.5V
0.1 VDD to 0.9 VDD
10 ns
0.5 VDD
1700 
Diagram Notes
All start and stop timing parameters apply to both read and write
cycles. Clock specifications are identical for read and write cycles.
Write timing parameters apply to slave address, word address, and
write data bits. Functional relationships are illustrated in the relevant
data sheet sections. These diagrams illustrate the timing parameters
only.
Output
100 pF
Read Bus Timing
tR
`
tF
t HIGH
t SP
t LOW
t SP
SCL
t SU:STA
1/fSCL
tBUF
t HD:DAT
t SU:DAT
SDA
Start
t DH
tAA
Stop Start
Acknowledge
Write Bus Timing
tHD:DAT
SCL
tHD:STA
tSU:STO
tSU:DAT
tAA
SDA
Start
Rev. 1.1
Apr. 2011
Stop Start
Acknowledge
Page 24 of 26
FM31T372/374/376/378-G
Mechanical Drawing
14-pin SOIC (JEDEC Standard)
Recommended PCB Footprint
7.70
3.70
6.00 ±0.20
3.90 ±0.13
2.00
0.65
1.27
Pin 1
0.25
0.50
8.64 ±0.10
1.27
0.33
0.51
0.10
0.25
0.19
0.25
45
1.35
1.75
0.10 mm
0-8
0.40
1.27
Refer to JEDEC MS-012 for complete dimensions and notes.
All dimensions in millimeters.
SOIC Package Marking Scheme
XXXXXXX-P
LLLLLLL
RIC YYWW
Rev. 1.1
Apr. 2011
Legend:
XXXXXX= part number, P= package type (-G)
LLLLLLL= lot code
RIC=Ramtron Int‟l Corp, YY=year, WW=work week
Example: FM31T378, “Green” SOIC package, Year 2010, Work Week 20
FM31T378-G
A00003G
RIC 1020
Page 25 of 26
FM31T372/374/376/378-G
Revision History
Revision
1.0
1.1
Rev. 1.1
Apr. 2011
Date
6/14/2010
4/18/2011
Summary
Preliminary status.
Documentation updates and clarifications. Changed IBAK limits.
Page 26 of 26