SPA2003 -T-S-A01 SILICON RECTIFIER VOLAGE 200 Volts CURRENT 20 Ampere FEATURES * Low cost * Low leakage * Low forward voltage drop * High current capability * High surge current capability * Ideal for solar panel PV application such as By-Pass diode R-7 MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 2.08 grams .065 (1.65) .96 (24.5) MIN. .061 (1.55) DIA. .299 (7.6) .291 (7.4) .319 (8.1) .311 (7.9) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o Ratings at 25 C ambient temperature unless otherwise specified. DIA. .96 (24.5) MIN. resistive or inductive load. Dimensions in inches and (millimeters) o MA X IMUM R AT ING S (At T A = 25 C unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum DC Forward Current @T L=125 oC(Note 2) Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Current Squared Time SYMBOL VRRM SPA2003-T-S-A01 VRMS 140 Volts VDC 200 Volts IO 20 Amps I FSM 400 Amps I T 663.7 A 2S 2 Typical Junction Capacitance (Note) Typical Thermal Resistance Operating Temperature Range Storage Temperature Range 200 CJ 125 R θJC 2.6 R θJL 1.2 UNITS Volts pF 0 C/ W TJ 175(Tj<200oC in Bypass Mode) T STG -55 to +175 SYMBOL VF SPA2003-T-S-A01 1.0 10 100 UNITS Volts 50 uAmps 0 C 0 C o ELECTRICAL CHARACTERISTICS (At TA = 25 C unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 20A DC @T A = 25 o C Maximum DC Reverse Current at Rated DC Blocking Voltage @T A = 100 o C Maximum Full Load Reverse Current Average Full Cycle .375” (9.5mm) lead length at T L = 75 oC IR NOTES : 1. Measured at 1 MH Z and applied reverse voltage of 4.0 volts 2. Heat-sink mounted 10mm max from body 3. Available in Halogen-free epoxy by adding suffix -HF after the part nbr. uAmps 2011-10 REV:O AVERAGE FORWARD CURRENT, (A) 25 20 D.C with heat sink 15 10 5 0 50 Single Phase Half Wave 60Hz Inductive or Resistive Load 100 150 175 200 INSTANTANEOUS REVERSE CURRENT, (uA) RATING AND CHARACTERISTIC CURVES ( SPA2003-T-S-A01 ) 1000 TA = 100 OC 100 TA = 25 OC 10 1.0 .1 0 O LEAD TEMPERATURE, ( C) 20 50 10 1.0 TJ = 25 OC Pulse width=300µS 1% Duty Cycle 0.2 0.4 0.6 0.8 1.0 1.2 1.4 60 80 100 120 140 FIG.2 TYPICAL REVERSE CHARACTERISTICS 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, (A) FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 0.1 40 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 600 8.3mS Single Half Sine-Wave JEDEC Method 500 400 300 200 100 0 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT Marking Description Cathode Band Rectron Logo Part No. V 2 Y M 0 A X Year – code: (Y:Last digit of year & A:2010, B:2011…) Month – code: (M:0~9,O,N,D) Voltage-code 01-------50V 02-------100V 03-------200V 04-------400V 05------600V 06------800V 07------1000V DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.