Wideband Amplifier RFC1G22-24 Product Features Application • GaAs MMIC • Very Low Distortion • Guaranteed Broadband Power Gain • Heat Sink 99.9% Copper, Ag or Gold Plate • Excellent Thermal Conductivity • Single Supply Voltage @ 24V • Low DC Power Consumption • No External Circuit needed • Drive Amplifier Description The RFC1G22-24 is specifically designed for up to 1GHz in frequency as amplifiers. This hybrid dynamic range amplifier module operates with a single voltage supply of 24V(DC). The RFC1G22-24 is equipped with over-voltage suppressor. Specifications Absolute Maximum Ratings PARAMETER MIN MAX UNITS VDD / VRFOUT - 28 VDC RFIN (Single Tone) - +15 dBm Storage Temperature -40 +100 ℃ Operating Temperature -20 +100 ℃ Electrical Specifications (TA = +25℃, VDD = 24V) RFC 1G22-24 PARAMETER MIN TYP MAX Bandwidth (MHz) 20 - 1000 Gain @1000MHz (dB) 21.0 22.0 - Gain Flatness @ 20-1000MHz (dB) - 1.5 2.0 Input / Output VSWR 2.5 : 1 2.0 : 1 IP3 (dBm)@ 20-1000MHz 48.0 50.0 - Power Output 1dB Comp. @ 20- 1000MHz (dBm) 29.0 30.0 IMD3 (dBc) Two Tone 20dBm Output @ 20-1000MHz 56.0 60.0 - Noise Figure (dB) @ 20-1000MHz - 3.5 5.0 Supply Current (mA) 380 400 430 ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 5.5 Wideband Amplifier RFC1G22-24 Typical RF Performance at 25℃ Parameter Units Typical Frequency MHz 20 500 1000 S21 - Gain dB 21 22 22 S11 – Input Return Loss dB -14 -30 -15 S22 – Output Return Loss dB -16 -16 -17 OIP1 dBm 29 30 29 OIP3 dBm 48.5 51 49 Noise Figure dB 3.6 3.5 4.8 Supply Voltage V 24 Current mA 380 ~ 430 Power Output 1dB Compression S-Parameters 36 30 20 34 S21 10 32 30 -10 S22 dBm Magnitude(dB) 0 -20 -30 28 26 S11 6 -40 24 -50 22 5 -60 -70 20 400 600 800 1000 1200 1400 1600 1800 2000 20 4 100 200 300 Frequency(MHz) 400 500 600 700 800 900 1000 Frequency(MHz) Noise Figure(dB) 20 200 Noise Figure OIP 3 3 6 54 5 52 2 50 OIP3(dBm) Noise Figure(dB) 1 4 3 48 0 20 100 200 300 400 500 600 700 800 900 46 2 44 1 42 40 0 20 100 200 300 400 500 600 700 Frequency(MHz) 800 900 1000 20 100 200 300 400 500 600 700 800 900 1000 Frequency(MHz) ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 5.5 1000 Wideband Amplifier RFC1G22-24 ESD PROTECTION Gallium Arsenide Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these devices. Some of the precautions recommended are; - Person at a workbench should be earthed via a wrist strap and a resistor. - All mains-powered equipment should be connected to the mains via an earth-leakage switch. - Equipment cases should be grounded. - Relative humidity should be maintained between 40% and 50%. - An ionizer is recommended. - Keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench. NOTES FOR CORRECT USE 1. 2. 3. 4. 5. 6. 7. On the power input port (Pin#5), 47uF/35V capacitor GND is recommended. The heat sink of CATV Hybrids is to be mounted in direct contact with the metal case of the equipment. Heat conducting grease should be applied to the module/equipment interface and the unit tightly secured. Put the power off before adjusting in/output matching of the system. The unit must have a common ground with the equipment and the analyzer. Pay close attention to the input voltage not to over power the hybrid. The space between bottom of socket and the tip of the lead is recommended to have space of 2mm+ to protect the pin Do not open the plastic cover to change the matching inside the hybrid. Once opened, RFHIC will not be responsible for the hybrid. Package Dimensions (Type: DP-27) Pin No. Function 1 2,3,7,8 5 9 RF Input Ground Vcc RF Output RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 5.5