RF3619D • 402 to 405 MHz Medical Band Front-end Filter • Single-ended Input/Outout Operation • Complies with Directive 2002/95/EC (RoHS) Pb 404.0 MHz SAW Filter Absolute Maximum Ratings Rating Value Units +10 dBm 3 V Operating Temperature Range -10 to +60 °C Storage Temperature Range in Tape and Reel -40 to +85 °C 260 °C Input Power Level DC Voltage on any Non-ground Pin Solder Reflow Temperature, 10 seconds, 5 cycles maximum SM3838-8 Case 3.8 x 3.8 Electrical Characteristics Characteristic Center Frequency at 25 °C Sym Notes fc 1, 2, 3 ILMIN Insertion Loss Passband Ripple, 402-405 MHz BW3 3 dB Bandwidth Minimum Typical Maximum 404.0 Units MHz 1, 3 2.1 2.3 dB 1, 3 0.6 0.8 dB 1 5.0 6.0 30 35 25 45 40 50 MHz Attenuation relative to ILMIN: 398.5 MHz 1, 3 408.5 MHz 383.5 MHz 423.5 MHz 38 Freq. Temp. Coefficient FTC Frequency Aging, First Year |fA| 5 Single-ended Input/Output Impedance Match 1 Differential Input/Output Impedance Match 1 Lid Symbolization (Y=year WW=week S=shift) Standard Reel Quantity Reel Size 7 Inch Reel Size 13 Inch dB 48 -37 ppm/k 10 50 ppm ohms 150 ohms A15, YWWS 9 500 Pieces/Reel 3000 Pieces/Reel CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture which is connected to a 50 test system. The frequency fc is defined as the midpoint between the 3 dB frequencies. Where noted specifications apply over the entire specified operating temperature range of -10 °C to +60 °C. Frequency aging is the change in fc with time and is specified at +65 °C or less. Aging may exceed the specification for prolonged temperatures above +65 °C. Typically, aging is greatest the first year after manufacture, decreasing significantly in subsequent years. The design, manufacturing process, and specifications of this device are subject to change. One or more of the following U.S. Patents apply: 4,54,488, 4,616,197, and others pending. All equipment designs utilizing this product must be approved by the appropriate government agency prior to manufacture or sale. Tape and Reel Standard Per ANSI / EIA 481. This product complies with Directive 2002/95/EC of the European Parlament and of the Council of 27 January 2003 on the restriction of the use of certain hazadous substances in electrical and electronic equipment. www.RFM.com E-mail: [email protected] © 2011-2012 by RF Monolithics, Inc. Page 1 of 3 RF3619D - 5/10/12 Filter Response Plots www.RFM.com E-mail: [email protected] © 2011-2012 by RF Monolithics, Inc. Page 2 of 3 RF3619D - 5/10/12 0.029 TYP. (O.74) 0.090 (2.29) 1 A 8 A15 2 YWWS 0.033 (0.84) 3 E C B 8 0.002 (0.05) 0.050 TYP. (1.27) 0.066 (1.68) 7 H 7 1 6 6 2 5 5 3 G 4 4 D 0.055 TYP. (1.40) F PCB Land Pattern Filter Primary Electrical Connections Case Dimensions Pin Connection 1 Ground 2 Ground 3 Input 4 Ground 5 Ground 6 Ground 7 Output 8 Ground mm Dimension A B C D E F G H Inches Min Nom Max Min Nom Max 3.6 3.6 1.00 0.95 0.90 0.50 2.39 1.40 3.8 3.8 1.20 1.10 1.0 0.6 2.54 1.75 4.0 4.0 1.40 1.25 1.10 0.70 2.69 2.05 0.14 0.14 0.04 0.033 0.035 0.020 0.090 0.055 0.15 0.15 0.05 0.043 0.04 0.024 0.100 0.069 0.16 0.16 0.055 0.05 0.043 0.028 0.110 0.080 Filter Alternate Electrical Connections Pin Filter Primary Connection Diagram www.RFM.com E-mail: [email protected] © 2011-2012 by RF Monolithics, Inc. 8 1 7 Connection 1 Ground 2 Input 3 Ground 4 Ground 5 Ground 6 Output 7 Ground 8 Ground In p u t O u tp u t 6 2 3 5 4 S in g le -e n d e d In p u t a n d O u tp u t Filter Alternate Connection Diagram Page 3 of 3 RF3619D - 5/10/12