500 MHz SAW Filter 1 MHz Bandwidth Part Number: SF0500BA03232S DESCRIPTION • • • 500 MHz SAW bandpass filter with 1 MHz bandwidth. 7 x 9 mm 11-pad LCC package. RoHS compliant. TYPICAL PERFORMANCE Amp 10 dB/div Amp 1 dB/div Phase 10 deg/div Delay 50 ns/div Center = 500 MHz, 2 MHz/div (25 kHz incr) S11 (490-510 MHz) S22 (490-510 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0500BA03232S Rev A 29-Mar-2010 ECN 36650 Page 1 of 3 500 MHz SAW Filter 1 MHz Bandwidth Part Number: SF0500BA03232S SPECIFICATION Parameter 3 dB Center Frequency, FC Minimum Insertion Loss Lower 1 dB Frequency 1 Upper 1 dB Frequency 1 1 dB Bandwidth 1 3 dB Bandwidth 1 40 dB Bandwidth 1 In-band Amplitude Variation In-band Group Delay Ripple Device Delay Relative Attenuation: 10 to 496 MHz 1 504 to 700 MHz 1 700 to 1000 MHz 1 Temperature Coefficient of Frequency (Tc) 2 Source/Load Impedance Ambient Temperature (Tref) Notes: Min 500.5 1 - Typ 500 11 499.29 500.85 1.56 2.1 5 0.4 35 0.9 Max 14 499.5 8 1 100 - 40 40 38 42 42 40 -0.032 50 25 - Units MHz dB MHz MHz MHz MHz MHz dB p-p ns p-p us dB dB dB ppm/˚C2 ohms ˚C 1. All dB levels are referenced to the insertion loss. 2. Typical shift of frequency response with temperature is: ∆f=(T-Tref)*Tc*Fc. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range (T) Input Power Level Min Max -45 -20 - 85 70 10 Units ˚C ˚C dBm MATCHING CIRCUIT 8 3 Input 50 Ω Single-ended Output 50 Ω Single-ended All other pads GND GND Ls1=8.2 nH, Cp1=15 pF, Ls2=10 nH, Cp2=14 pF Notes: • Recommend 2% tolerance matching components. Typical inductor Q=40. • Matching values are for reference only. Actual values are dependent upon board layout. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0500BA03232S Rev A 29-Mar-2010 ECN 36650 Page 2 of 3 500 MHz SAW Filter 1 MHz Bandwidth Part Number: SF0500BA03232S PACKAGE OUTLINE SMI BA03232S ∆ YYDDD Date Code (YY=year, DDD=day) Pad 1 identifier SUGGESTED FOOTPRINT Tolerances are typically ±0.15 mm except where indicated. Pad Configuration: Input: 8 Output: 3 Ground: All other pads Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0500BA03232S Rev A 29-Mar-2010 ECN 36650 Page 3 of 3