NSC DP83849ID

DP83849ID PHYTER® DUAL Industrial Temperature with Fiber Support (FX)
Dual Port 10/100 Mb/s Ethernet Physical Layer Transceiver
General Description
Features
The number of applications requiring Ethernet Connectivity continues to expand. Along with this
increased market demand is a change in application
requirements. Where single channel Ethernet used to
be sufficient, many applications such as wireless
remote base stations and industrial networking now
require DUAL Port functionality for redundancy or system management.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The DP83849ID is a highly reliable, feature rich device
perfectly suited for industrial applications enabling
Ethernet on the factory floor. The DP83849ID features
two fully independent 10/100 ports for multi-port applications.
The DP83849ID provides optimum flexibility in MPU
selection by supporting both MII and RMII interfaces.
The device also provides flexibility by supporting both
copper and fiber media.
In addition this device includes a powerful new diagnostics tool to ensure initial network operation and
maintenance. In addition to the TDR scheme, commonly used for detecting faults during installation,
NATIONAL’s innovative cable diagnostics provides for
real time continuous monitoring of the link quality. This
allows the system designer to implement a fault prediction mechanism to detect and warn of changing or
deteriorating link conditions.
With the DP83849ID, National Semiconductor continues to build on its Ethernet expertise and leadership
position by providing a powerful combination of features and flexibility, easing Ethernet implementation for
the system designer.
•
•
•
•
Low-power 3.3V, 0.18µm CMOS technology
Low power consumption <600mW Typical
3.3V MAC Interface
Auto-MDIX for 10/100 Mb/s
Energy Detection Mode
Dynamic Integrity Utility
Dynamic Link Quality Monitoring
TDR based Cable Diagnostic and Cable Length Detection
Optimized Latency for Real Time Ethernet Operation
Reference Clock out
RMII Rev. 1.2 Interface (configurable)
SNI Interface (configurable)
MII Serial Management Interface (MDC and MDIO)
IEEE 802.3u MII
IEEE 802.3u Auto-Negotiation and Parallel Detection
IEEE 802.3u ENDEC, 10BASE-T transceivers and filters
IEEE 802.3u PCS, 100BASE-TX transceivers and filters
IEEE 802.3u 100BASE-FX Fiber Interface
IEEE 1149.1 JTAG
Integrated ANSI X3.263 compliant TP-PMD physical sub-layer
with adaptive equalization and Baseline Wander compensation
Programmable LED support for Link, 10 /100 Mb/s Mode, Activity, Duplex and Collision Detect
Single register access for complete PHY status
10/100 Mb/s packet BIST (Built in Self Test)
80-pin TQFP package (12mm x 12mm)
Applications
•
•
•
•
•
Medical Instrumentation
Factory Automation
Motor & Motion Control
Wireless Remote Base Station
General Embedded Applications
System Diagram
MAC
Magnetics
DP83849ID
MPU/CPU
Port A
MII/RMII/SNI
25 MHz
Clock
Source
Status
LEDs
RJ-45
MII/RMII/SNI
RJ-45
Port B
Magnetics
MAC
100BASE-FX
10BASE-T
or
100BASE-TX
10BASE-T
or
100BASE-TX
100BASE-FX
Typical Application
PHYTER is a registered trademark of National Semiconductor Corporation
© 2006 National Semiconductor Corporation
www.national.com
1
DP83849ID PHYTER® DUAL Industrial Temperature with Fiber Support (FX)
Dual Port 10/100 Mb/s Ethernet Physical Layer Transceiver
August 2006
TX
RX
MDC
DP83849ID
MII MANAGEMENT
INTERFACE
PORT A
MII/RMII/SNI
PORT B
MII/RMII/SNI
TX
MDIO
RX
MANAGEMENT
INTERFACE
10/100 PHY CORE
10/100 PHY CORE
PORT A
PORT B
BOUNDARY
SCAN
LED
DRIVERS
LEDS
TPTD/FXTD±
LED
DRIVERS
LEDS
TPRD/FXRD±
JTAG
TPTD/FXTD±
TPRD/FXRD±
Figure 1. DP83849ID Functional Block Diagram
2
www.national.com
1.0 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Serial Management Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
1.2 MAC Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
1.3 Clock Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
1.4 LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
1.5 JTAG Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.6 Reset and Power Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.7 Strap Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.8 10 Mb/s and 100 Mb/s PMD Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
1.9 Special Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
1.10 Power Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
1.11 Package Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.0 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.1 Media Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.2 Auto-Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.2.1
2.2.2
2.2.3
2.2.4
2.2.5
2.2.6
Auto-Negotiation Pin Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-Negotiation Register Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-Negotiation Parallel Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-Negotiation Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling Auto-Negotiation via Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-Negotiation Complete Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
18
18
18
18
2.3 Auto-MDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
2.4 PHY Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
2.4.1 MII Isolate Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.5 LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.5.1 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.5.2 LED Direct Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.6 Half Duplex vs. Full Duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2.7 Internal Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2.8 BIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.0 MAC Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1 MII Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3.1.1 Nibble-wide MII Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.2 Collision Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.3 Carrier Sense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2 Reduced MII Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.3 10 Mb Serial Network Interface (SNI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.4 802.3u MII Serial Management Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3.4.1
3.4.2
3.4.3
3.4.4
Serial Management Register Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Management Access Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Management Preamble Suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Simultaneous Register Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
24
25
25
4.0 Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.1 100BASE-TX TRANSMITTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
4.1.1
4.1.2
4.1.3
4.1.4
Code-group Encoding and Injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scrambler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRZ to NRZI Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Binary to MLT-3 Convertor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
28
28
28
4.2 100BASE-TX RECEIVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
4.2.1 Analog Front End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2 Digital Signal Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2.1 Digital Adaptive Equalization and Gain Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2.2 Base Line Wander Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3 Signal Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4 MLT-3 to NRZI Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5 NRZI to NRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.6 Serial to Parallel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
28
28
30
31
31
31
31
31
www.national.com
DP83849ID
Table of Contents
32
32
32
32
32
4.3 100BASE-FX Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
4.3.1 100BASE-FX Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.3.2 100BASE-FX Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.3.3 Far-End Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.4 10BASE-T TRANSCEIVER MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
4.4.1 Operational Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.2 Smart Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.3 Collision Detection and SQE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.4 Carrier Sense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.5 Normal Link Pulse Detection/Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.6 Jabber Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.7 Automatic Link Polarity Detection and Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.8 Transmit and Receive Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.9 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.10 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
33
34
34
34
34
34
34
34
34
5.0 Design Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5.1
5.2
5.3
5.4
5.5
5.6
TPI Network Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Fiber Network Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
ESD Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Clock In (X1) Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Power Feedback Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Power Down/Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
5.6.1 Power Down Control Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.6.2 Interrupt Mechanisms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
5.7 Energy Detect Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
5.8 Link Diagnostic Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
5.8.1 Linked Cable Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.1.1 Polarity Reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.1.2 Cable Swap Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.1.3 100MB Cable Length Estimation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.1.4 Frequency Offset Relative to Link Partner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.1.5 Cable Signal Quality Estimation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.2 Link Quality Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.2.1 Link Quality Monitor Control and Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.2.2 Checking Current Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.2.3 Threshold Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.3 TDR Cable Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.3.1 TDR Pulse Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.3.2 TDR Pulse Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.3.3 TDR Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.3.4 TDR Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
39
39
39
39
40
40
40
40
40
41
41
41
41
42
6.0 Reset Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6.1 Hardware Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
6.2 Full Software Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
6.3 Soft Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
7.0 Register Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
7.1 Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
7.1.1
7.1.2
7.1.3
7.1.4
7.1.5
7.1.6
7.1.7
7.1.8
Basic Mode Control Register (BMCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Mode Status Register (BMSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PHY Identifier Register #1 (PHYIDR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PHY Identifier Register #2 (PHYIDR2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-Negotiation Advertisement Register (ANAR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page) . . . . . . . . . . . . . . . .
Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page) . . . . . . . . . . . . . . . . .
Auto-Negotiate Expansion Register (ANER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
49
51
52
52
52
54
55
56
www.national.com
DP83849ID
4.2.7 Descrambler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.8 Code-group Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.9 4B/5B Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.10 100BASE-TX Link Integrity Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.11 Bad SSD Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
58
60
60
61
7.2 Extended Registers - Page 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
7.2.1 False Carrier Sense Counter Register (FCSCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.2 Receiver Error Counter Register (RECR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.3 100 Mb/s PCS Configuration and Status Register (PCSR) . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.4 RMII and Bypass Register (RBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.5 LED Direct Control Register (LEDCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.6 PHY Control Register (PHYCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.7 10 Base-T Status/Control Register (10BTSCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.8 CD Test and BIST Extensions Register (CDCTRL1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.9 Phy Control Register 2 (PHYCR2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.10 Energy Detect Control (EDCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
62
62
62
64
65
66
67
69
69
70
7.3 Link Diagnostics Registers - Page 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
7.3.1 100Mb Length Detect Register (LEN100_DET), Page 2, address 14h . . . . . . . . . . . . . . . . .
7.3.2 100Mb Frequency Offset Indication Register (FREQ100), Page 2, address 15h . . . . . . . . .
7.3.3 TDR Control Register (TDR_CTRL), Page 2, address 16h . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.4 TDR Window Register (TDR_WIN), Page 2, address 17h . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.5 TDR Peak Register (TDR_PEAK), Page 2, address 18h . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.6 TDR Threshold Register (TDR_THR), Page 2, address 19h . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.7 Variance Control Register (VAR_CTRL), Page 2, address 1Ah . . . . . . . . . . . . . . . . . . . . . .
7.3.8 Variance Data Register (VAR_DATA), Page 2, address 1Bh . . . . . . . . . . . . . . . . . . . . . . . .
7.3.9 Link Quality Monitor Register (LQMR), Page 2, address 1Dh . . . . . . . . . . . . . . . . . . . . . . . .
7.3.10 Link Quality Data Register (LQDR), Page 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
71
72
73
73
73
74
74
75
76
8.0 Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
8.1 DC Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
8.2 AC Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
8.2.1 Power Up Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.2 Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.3 MII Serial Management Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.4 100 Mb/s MII Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.5 100 Mb/s MII Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.6 100BASE-TX and 100BASE-FX MII Transmit Packet Latency Timing . . . . . . . . . . . . . . . . .
8.2.7 100BASE-TX and 100BASE-FX MII Transmit Packet Deassertion Timing . . . . . . . . . . . . . .
8.2.8 100BASE-TX Transmit Timing (tR/F & Jitter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.9 100BASE-TX and 100BASE-FX MII Receive Packet Latency Timing . . . . . . . . . . . . . . . . .
8.2.10 100BASE-TX and 100BASE-FX MII Receive Packet Deassertion Timing . . . . . . . . . . . . .
8.2.11 10 Mb/s MII Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.12 10 Mb/s MII Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.13 10 Mb/s Serial Mode Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.14 10 Mb/s Serial Mode Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.15 10BASE-T Transmit Timing (Start of Packet) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.16 10BASE-T Transmit Timing (End of Packet) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.17 10BASE-T Receive Timing (Start of Packet) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.18 10BASE-T Receive Timing (End of Packet) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.19 10 Mb/s Heartbeat Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.20 10 Mb/s Jabber Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.21 10BASE-T Normal Link Pulse Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.22 Auto-Negotiation Fast Link Pulse (FLP) Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.23 100BASE-TX Signal Detect Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.24 100 Mb/s Internal Loopback Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.25 10 Mb/s Internal Loopback Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.26 RMII Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.27 RMII Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.28 Isolation Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.29 CLK2MAC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
80
81
81
82
82
83
84
85
85
86
86
87
87
88
88
89
89
90
90
91
91
92
92
93
94
95
96
96
9.0 Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
5
www.national.com
DP83849ID
7.1.9 Auto-Negotiation Next Page Transmit Register (ANNPTR) . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.10 PHY Status Register (PHYSTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.11 MII Interrupt Control Register (MICR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.12 MII Interrupt Status and Misc. Control Register (MISR) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.13 Page Select Register (PAGESEL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1. DP83849ID Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 2. PHYAD Strapping Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 3. AN Strapping and LED Loading Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 4. Typical MDC/MDIO Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 5. Typical MDC/MDIO Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 6. 100BASE-TX Transmit Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 7. 100BASE-TX Receive Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 9. EIA/TIA Attenuation vs. Frequency for 0, 50, 100, 130 & 150 meters of CAT 5 cable . . . . . . . . . . . 30
Figure 10. 100BASE-TX BLW Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 11. 10BASE-T Twisted Pair Smart Squelch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 12. 10/100 Mb/s Twisted Pair Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 13. 100 Mb/s Fiber Pair Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 14. Crystal Oscillator Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 15. Power Feeback Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6
www.national.com
DP83849ID
List of Figures
Table 1. Auto-Negotiation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Table 2. PHY Address Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Table 3. LED Mode Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Table 4. Supported packet sizes at +/-50ppm frequency accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Table 5. Typical MDIO Frame Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Table 13. 4B5B Code-Group Encoding/Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Table 14. 25 MHz Oscillator Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Table 15. 50 MHz Oscillator Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Table 16. 25 MHz Crystal Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Table 17. Link Quality Monitor Parameter Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Table 18. Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Table 19. Register Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Table 20. Basic Mode Control Register (BMCR), address 00h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Table 21. Basic Mode Status Register (BMSR), address 01h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Table 22. PHY Identifier Register #1 (PHYIDR1), address 02h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Table 23. PHY Identifier Register #2 (PHYIDR2), address 03h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Table 24. Negotiation Advertisement Register (ANAR), address 04h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Table 25. Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page), address 05h . . . . . . . . .54
Table 26. Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page), address 05h . . . . . . . . . .55
Table 27. Auto-Negotiate Expansion Register (ANER), address 06h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Table 28. Auto-Negotiation Next Page Transmit Register (ANNPTR), address 07h . . . . . . . . . . . . . . . . . . . .57
Table 29. PHY Status Register (PHYSTS), address 10h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Table 30. MII Interrupt Control Register (MICR), address 11h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Table 31. MII Interrupt Status and Misc. Control Register (MISR), address 12h . . . . . . . . . . . . . . . . . . . . . . .60
Table 32. Page Select Register (PAGESEL), address 13h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Table 33. False Carrier Sense Counter Register (FCSCR), address 14h . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Table 34. Receiver Error Counter Register (RECR), address 15h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Table 35. 100 Mb/s PCS Configuration and Status Register (PCSR), address 16h . . . . . . . . . . . . . . . . . . . . .62
Table 36. RMII and Bypass Register (RBR), addresses 17h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Table 37. LED Direct Control Register (LEDCR), address 18h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Table 38. PHY Control Register (PHYCR), address 19h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Table 39. 10Base-T Status/Control Register (10BTSCR), address 1Ah . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Table 40. CD Test and BIST Extensions Register (CDCTRL1), address 1Bh . . . . . . . . . . . . . . . . . . . . . . . . . .69
Table 41. Phy Control Register 2 (PHYCR2), address 1Ch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Table 42. Energy Detect Control (EDCR), address 1Dh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Table 43. 100Mb Length Detect Register (LEN100_DET), address 14h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Table 44. 100Mb Frequency Offset Indication Register (FREQ100), address 15h . . . . . . . . . . . . . . . . . . . . . .71
Table 45. TDR Control Register (TDR_CTRL), address 16h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Table 46. TDR Window Register (TDR_WIN), address 17h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Table 47. TDR Peak Register (TDR_PEAK), address 18h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Table 48. TDR Threshold Register (TDR_THR), address 19h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Table 49. Variance Control Register (VAR_CTRL), address 1Ah . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Table 50. Variance Data Register (VAR_DATA), address 1Bh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Table 51. Link Quality Monitor Register (LQMR), address 1Dh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Table 52. Link Quality Data Register (LQDR), address 1Eh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
7
www.national.com
DP83849ID
List of Tables
11
12
13
14
15
16
17
18
19
20
TX_CLK_A
TX_EN_A
TXD0_A
TXD1_A
TXD2_A
TXD3_A/SNI_MODE_A
PWRDOWN_INT_A
LED_LINK_A/AN0_A
LED_SPEED_A/FXSD_A/AN1_A
10
IOVDD1
IOGND1
9
6
COREGND1
RXD3_A/ED_EN_A
5
RXD1_A/PHYAD2
8
4
RXD0_A/PHYAD1
7
3
COL_A/FX_EN_A
RXD2_A/CLK2MAC_DIS
2
PFBIN1
1
RX_ER_A/MDIX_EN_A
o
CRS_A/CRS_DV_A/LED_CFG_A
CRS_B/CRS_DV_B/LED_CFG_B
61
40
ANAGND4
RX_DV_B/MII_MODE_B
62
39
TPRDM_B/FXRDM_B
RX_CLK_B
63
38
TPRDP_B/FXRDP_B
IOGND3
64
37
CDGND2
IOVDD3
65
36
TPTDM_B/FXTDM_B
MDIO
66
35
TPTDP_B/FXTDP_B
MDC
67
34
PFBIN3
CLK2MAC
68
33
ANAGND3
X2
69
32
X1
70
RBIAS
31
PFBOUT
RESET_N
71
30
ANA33VDD
TCK
72
29
ANAGND2
TDO
73
28
PFBIN2
TMS
74
27
TPTDP_A/FXTDP_A
TRSTN
75
26
TPTDM_A/FXTDM_A
TDI
76
25
CDGND1
IOGND4
77
24
TPRDP_A/FXRDP_A
IOVDD4
78
23
TPRDM_A/FXRDM_A
RX_CLK_A
79
22
ANAGND1
RX_DV_A/MII_MODE_A
80
21
LED_ACT/LED_COL/AN_EN_A
DP83849IDVS
8
RX_ER_B/MDIX_EN_B
COL_B/FX_EN_B
RXD0_B/PHYAD3
RXD1_B/PHYAD4
RXD2_B
COREGND2
PFBIN4
RXD3_B/ED_EN_B
IOGND2
IOVDD2
TX_CLK_B
TX_EN_B
TXD0_B
TXD1_B
TXD2_B
TXD3_B/SNI_MODE_B
PWRDOWN_INT_B
LED_LINK_B/AN0_B
LED_SPEED_B/FXSD_B/AN1_B
LED_ACT/LED_COL/AN_EN_B
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
DP83849ID
Pin Layout
Top View
NS Package Number VHB80A
www.national.com
The DP83849ID pins are classified into the following interface categories (each interface is described in the sections
that follow):
Note: Strapping pin option. Please see Section 1.7 for strap
definitions.
—
—
—
—
—
—
—
—
—
—
Type: I
Type: O
Type: I/O
Type OD
Type: PD,PU
Type: S
All DP83849ID signal pins are I/O cells regardless of the
particular use. The definitions below define the functionality
of the I/O cells for each pin.
Serial Management Interface
MAC Data Interface
Clock Interface
LED Interface
JTAG Interface
Reset and Power Down
Strap Options
10/100 Mb/s PMD Interface
Special Connect Pins
Power and Ground pins
Input
Output
Input/Output
Open Drain
Internal Pulldown/Pullup
Strapping Pin (All strap pins have weak internal pull-ups or pull-downs. If the default
strap value is to be changed then an external 2.2 kΩ resistor should be used. Please
see Section 1.7 for details.)
1.1 Serial Management Interface
Type
Pin #
Description
MDC
Signal Name
I
67
MANAGEMENT DATA CLOCK: Synchronous clock to the MDIO
management data input/output serial interface which may be asynchronous to transmit and receive clocks. The maximum clock rate is
25 MHz with no minimum clock rate.
MDIO
I/O
66
MANAGEMENT DATA I/O: Bi-directional management instruction/data signal that may be sourced by the station management entity
or the PHY. This pin requires a 1.5 kΩ pullup resistor.
Type
Pin #
Description
O
12
MII TRANSMIT CLOCK: 25 MHz Transmit clock output in 100 Mb/s
mode or 2.5 MHz in 10 Mb/s mode derived from the 25 MHz reference
clock.
1.2 MAC Data Interface
Signal Name
TX_CLK_A
TX_CLK_B
50
Unused in RMII mode. The device uses the X1 reference clock input
as the 50 MHz reference for both transmit and receive.
SNI TRANSMIT CLOCK: 10 MHz Transmit clock output in 10 Mb SNI
mode. The MAC should source TX_EN and TXD_0 using this clock.
TX_EN_A
I
TX_EN_B
13
49
MII TRANSMIT ENABLE: Active high input indicates the presence of
valid data inputs on TXD[3:0].
RMII TRANSMIT ENABLE: Active high input indicates the presence
of valid data on TXD[1:0].
SNI TRANSMIT ENABLE: Active high input indicates the presence of
valid data on TXD_0.
TXD[3:0]_A
TXD[3:0]_B
I
17,16,15,14 MII TRANSMIT DATA: Transmit data MII input pins, TXD[3:0], that
45,46,47,48 accept data synchronous to the TX_CLK (2.5 MHz in 10 Mb/s mode
or 25 MHz in 100 Mb/s mode).
RMII TRANSMIT DATA: Transmit data RMII input pins, TXD[1:0],
that accept data synchronous to the 50 MHz reference clock.
SNI TRANSMIT DATA: Transmit data SNI input pin, TXD_0, that accept data synchronous to the TX_CLK (10 MHz in 10 Mb/s SNI mode).
9
www.national.com
DP83849ID
1.0 Pin Descriptions
Signal Name
RX_CLK_A
Type
Pin #
Description
O
79
MII RECEIVE CLOCK: Provides the 25 MHz recovered receive
clocks for 100 Mb/s mode and 2.5 MHz for 10 Mb/s mode.
RX_CLK_B
63
Unused in RMII mode. The device uses the X1 reference clock input
as the 50 MHz reference for both transmit and receive.
SNI RECEIVE CLOCK: Provides the 10 MHz recovered receive
clocks for 10 Mb/s SNI mode.
RX_DV_A
O
RX_DV_B
80
62
MII RECEIVE DATA VALID: Asserted high to indicate that valid data
is present on the corresponding RXD[3:0].
RMII RECEIVE DATA VALID: Asserted high to indicate that valid
data is present on the corresponding RXD[1:0]. This signal is not required in RMII mode, since CRS_DV includes the RX_DV signal, but
is provided to allow simpler recovery of the Receive data.
This pin is not used in SNI mode.
RX_ER_A
O
RX_ER_B
2
60
MII RECEIVE ERROR: Asserted high synchronously to RX_CLK to
indicate that an invalid symbol has been detected within a received
packet in 100 Mb/s mode.
RMII RECEIVE ERROR: Asserted high synchronously to X1 whenever an invalid symbol is detected, and CRS_DV is asserted in 100 Mb/s
mode. This pin is also asserted on detection of a False Carrier event.
This pin is not required to be used by a MAC in RMII mode, since the
Phy is required to corrupt data on a receive error.
This pin is not used in SNI mode.
RXD[3:0]_A
O
RXD[3:0]_B
9,8,5,4
MII RECEIVE DATA: Nibble wide receive data signals driven syn53,56,57,58 chronously to the RX_CLK, 25 MHz for 100 Mb/s mode, 2.5 MHz for
10 Mb/s mode). RXD[3:0] signals contain valid data when RX_DV is
asserted.
RMII RECEIVE DATA: 2-bits receive data signals, RXD[1:0], driven
synchronously to the X1 clock, 50 MHz.
SNI RECEIVE DATA: Receive data signal, RXD_0, driven synchronously to the RX_CLK. RXD_0 contains valid data when CRS is asserted. RXD[3:1] are not used in this mode.
CRS_A/CRS_DV_A
O
CRS_B/CRS_DV_B
1
61
MII CARRIER SENSE: Asserted high to indicate the receive medium
is non-idle.
RMII CARRIER SENSE/RECEIVE DATA VALID: This signal combines the RMII Carrier and Receive Data Valid indications. For a detailed description of this signal, see the RMII Specification.
SNI CARRIER SENSE: Asserted high to indicate the receive medium
is non-idle. It is used to frame valid receive data on the RXD_0 signal.
COL_A
COL_B
O
3
59
MII COLLISION DETECT: Asserted high to indicate detection of a
collision condition (simultaneous transmit and receive activity) in 10
Mb/s and 100 Mb/s Half Duplex Modes.
While in 10BASE-T Half Duplex mode with heartbeat enabled this pin
is also asserted for a duration of approximately 1µs at the end of
transmission to indicate heartbeat (SQE test).
In Full Duplex Mode, for 10 Mb/s or 100 Mb/s operation, this signal is
always logic 0. There is no heartbeat function during 10 Mb/s full duplex operation.
RMII COLLISION DETECT: Per the RMII Specification, no COL signal is required. The MAC will recover CRS from the CRS_DV signal
and use that along with its TX_EN signal to determine collision.
SNI COLLISION DETECT: Asserted high to indicate detection of a
collision condition (simultaneous transmit and receive activity) in 10
Mb/s SNI mode.
10
www.national.com
DP83849ID
1.2 MAC Data Interface (Continued)
Signal Name
X1
Type
Pin #
Description
I
70
CRYSTAL/OSCILLATOR INPUT: This pin is the primary clock
reference input for the DP83849ID and must be connected to a 25
MHz 0.005% (+50 ppm) clock source. The DP83849ID supports
either an external crystal resonator connected across pins X1 and
X2, or an external CMOS-level oscillator source connected to pin
X1 only.
RMII REFERENCE CLOCK: This pin is the primary clock reference input for the RMII mode and must be connected to a 50 MHz
0.005% (+50 ppm) CMOS-level oscillator source.
X2
O
69
CRYSTAL OUTPUT: This pin is the primary clock reference output to connect to an external 25 MHz crystal resonator device.
This pin must be left unconnected if an external CMOS oscillator
clock source is used.
CLK2MAC
O
68
CLOCK TO MAC:
In MII mode, this pin provides a 25 MHz clock output to the system.
In RMII mode, this pin provides a 50 MHz clock output to the system.
This allows other devices to use the reference clock from the
DP83849ID without requiring additional clock sources.
If the system does not require the CLK2MAC signal, the
CLK2MAC output should be disabled via the CLK2MAC disable
strap.
1.4 LED Interface
The DP83849ID supports three configurable LED pins. The is register configurable. The definitions for the LEDs for
LEDs support two operational modes which are selected each mode are detailed below. Since the LEDs are also
by the LED mode strap and a third operational mode which used as strap options, the polarity of the LED output is
dependent on whether the pin is pulled up or down.
Signal Name
LED_LINK_A
Type
Pin #
Description
I/O
19
LINK LED: In Mode 1, this pin indicates the status of the LINK.
The LED will be ON when Link is good.
LED_LINK_B
43
LINK/ACT LED: In Mode 2 and Mode 3, this pin indicates transmit
and receive activity in addition to the status of the Link. The LED
will be ON when Link is good. It will blink when the transmitter or
receiver is active.
LED_SPEED_A
I/O
LED_SPEED_B
LED_ACT/LED_COL_A
LED_ACT/LED_COL_B
20
42
I/O
21
41
SPEED LED: The LED is ON when device is in 100 Mb/s and OFF
when in 10 Mb/s. Functionality of this LED is independent of mode
selected.
ACTIVITY LED: In Mode 1, this pin is the Activity LED which is
ON when activity is present on either Transmit or Receive.
COLLISION/DUPLEX LED: In Mode 2, this pin by default indicates Collision detection. For Mode 3, this LED output may be
programmed to indicate Full-duplex status instead of Collision.
11
www.national.com
DP83849ID
1.3 Clock Interface
DP83849ID
1.5 JTAG Interface
Signal Name
TCK
Type
Pin #
I, PU
72
Description
TEST CLOCK
This pin has a weak internal pullup.
TDO
O
73
TEST OUTPUT
TMS
I, PU
74
TEST MODE SELECT
TRSTN
I, PU
75
This pin has a weak internal pullup.
TEST RESET Active low test reset.
This pin has a weak internal pullup.
TDI
I, PU
76
TEST DATA INPUT
This pin has a weak internal pullup.
1.6 Reset and Power Down
Signal Name
Type
Pin #
Description
RESET_N
I, PU
71
RESET: Active Low input that initializes or re-initializes the
DP83849ID. Asserting this pin low for at least 1 µs will force a reset process to occur. All internal registers will re-initialize to their
default states as specified for each bit in the Register Block section. All strap options are re-initialized as well.
PWRDOWN_INT_A
I, PU
18
The default function of this pin is POWER DOWN.
44
POWER DOWN: The pin is an active low input in this mode and
should be asserted low to put the device in a Power Down mode.
PWRDOWN_INT_B
INTERRUPT: The pin is an open drain output in this mode and will
be asserted low when an interrupt condition occurs. Although the
pin has a weak internal pull-up, some applications may require an
external pull-up resister. Register access is required for the pin to
be used as an interrupt mechanism. See Section 5.6.2 Interrupt
Mechanism for more details on the interrupt mechanisms.
1.7 Strap Options
The DP83849ID uses many of the functional pins as strap
options. The values of these pins are sampled during reset
and used to strap the device into specific modes of operation. The strap option pin assignments are defined below.
The functional pin name is indicated in parentheses.
Signal Name
A 2.2 kΩ resistor should be used for pull-down or pull-up to
change the default strap option. If the default option is
required, then there is no need for external pull-up or pull
down resistors. Since these pins may have alternate functions after reset is deasserted, they should not be connected directly to VCC or GND.f
Type
Pin #
Description
PHYAD1 (RXD0_A)
S, O, PD
4
PHYAD2 (RXD1_A)
S, O, PD
5
PHYAD3 (RXD0_B)
S, O, PD
58
PHY ADDRESS [4:1]: The DP83849ID provides four PHY address pins, the state of which are latched into the PHYCTRL register at system Hardware-Reset. Phy Address[0] selects between
ports A and B.
PHYAD4 (RXD1_B)
S, O, PD
57
The DP83849ID supports PHY Address strapping for Port A even
values 0 (<0000_0>) through 30 (<1111_0>). Port B will be
strapped to odd values 1 (<0000_1>) through 31 (<1111_1>).
PHYAD[4:1] pins have weak internal pull-down resistors.
12
www.national.com
Signal Name
FX_EN_A (COL_A)
Type
Pin #
Description
S, I, PD
3
FX ENABLE: Default is to disable 100BASE-FX (Fiber) mode.
This strapping option enables 100BASE-FX. An external pull-up
will enable 100BASE-FX mode.
FX_EN_B (COL_B)
AN_EN
(LED_ACT/LED_COL_A)
AN1_A (LED_SPEED_A)
59
S, O, PU
21
20
19
AN0_A (LED_LINK_A)
AN_EN
(LED_ACT/LED_COL_B)
AN1_B (LED_SPEED_B)
AN0_B (LED_LINK_B)
41
42
43
Auto-Negotiation Enable: When high, this enables Auto-Negotiation with the capability set by AN0 and AN1 pins. When low, this
puts the part into Forced Mode with the capability set by AN0 and
AN1 pins.
AN0 / AN1: These input pins control the forced or advertised operating mode of the DP83849ID according to the following table. The
value on these pins is set by connecting the input pins to GND (0)
or VCC (1) through 2.2 kΩ resistors. These pins should NEVER
be connected directly to GND or VCC.
Fiber Mode Duplex Selection: If Fiber mode is strapped using the
FX_EN pin, the AN0 strap value is used to select Half or Full Duplex. AN_EN and AN1are ignored if FX_EN is asserted, since Fiber mode is 100Mb only and does not support Auto-Negotiation.
The value set at this input is latched into the DP83849ID at Hardware-Reset.
The float/pull-down status of these pins are latched into the Basic
Mode Control Register and the Auto_Negotiation Advertisement
Register during Hardware-Reset.
The default is 0111 since the FX_EN pin has an internal pull-down
and the Auto-Negotiation pins have internal pull-ups.
FX_EN AN_EN AN1
AN0
Forced Mode
0
0
0
0
10BASE-T, Half-Duplex
0
0
0
1
10BASE-T, Full-Duplex
0
0
1
0
100BASE-TX, Half-Duplex
0
0
1
1
100BASE-TX, Full-Duplex
1
X
X
0
100BASE-FX, Half-Duplex
1
X
X
1
100BASE-FX, Full-Duplex
FX_EN AN_EN AN1
AN0
Advertised Mode
0
1
0
0
10BASE-T, Half/Full-Duplex
0
1
0
1
100BASE-TX, Half/Full-Duplex
0
1
1
0
10BASE-T Half-Duplex
100BASE-TX, Half-Duplex
0
1
1
1
10BASE-T, Half/Full-Duplex
100BASE-TX, Half/Full-Duplex
13
www.national.com
DP83849ID
1.7 Strap Options (Continued)
Signal Name
MII_MODE_A (RX_DV_A)
Type
Pin #
Description
S, O, PD
80
MII MODE SELECT: This strapping option pair determines the
operating mode of the MAC Data Interface. Default operation (No
pull-ups) will enable normal MII Mode of operation. Strapping
MII_MODE high will cause the device to be in RMII or SNI modes
of operation, determined by the status of the SNI_MODE strap.
Since the pins include internal pull-downs, the default values are
0. Both MAC Data Interfaces must have their RMII Mode settings
the same, i.e. both in RMII mode or both not in RMII mode.
SNI_MODE_A (TXD3_A)
17
MII_MODE_B (RX_DV_B)
62
SNI_MODE_B (TXD3_B)
45
The following table details the configurations:
LED_CFG_A
(CRS_A/CRS_DV_A)
S, O, PU
LED_CFG_B
(CRS_B/CRS_DV_B)
1
61
MII_MODE
SNI_MODE
MAC Interface
Mode
0
X
MII Mode
1
0
RMII Mode
1
1
10 Mb SNI Mode
LED CONFIGURATION: This strapping option determines the
mode of operation of the LED pins. Default is Mode 1. Mode 1 and
Mode 2 can be controlled via the strap option. All modes are configurable via register access.
See Table 3 on page 20 for LED Mode Selection.
MDIX_EN_A (RX_ER_A)
MDIX_EN_B (RX_ER_B)
S, O, PU
ED_EN_A (RXD3_A)
ED_EN_B (RXD3_B)
S, O, PD
CLK2MAC_DIS (RXD2_A)
S, O, PD
2
60
9
53
8
MDIX ENABLE: Default is to enable MDIX. This strapping option
disables Auto-MDIX. An external pull-down will disable Auto-MDIX
mode.
Energy Detect ENABLE: Default is to disable Energy Detect
mode. This strapping option enables Energy Detect mode for the
port. In Energy Detect mode, the device will initially be in a lowpower state until detecting activity on the wire. An external pull-up
will enable Energy Detect mode.
Clock to MAC Disable: This strapping option disables (floats) the
CLK2MAC pin. Default is to enable CLK2MAC output. An external
pullup will disable (float) the CLK2MAC pin. If the system does not
require the CLK2MAC signal, the CLK2MAC output should be disabled via this strap option.
14
www.national.com
DP83849ID
1.7 Strap Options (Continued)
Signal Name
Type
Pin #
I/O
26
10BASE-T or 100BASE-TX or 100BASE-FX Transmit Data
TPTDP_A/FXTDP_A
27
TPTDM_B/FXTDM_B
36
TPTDP_B/FXTDP_B
35
In 10BASE-T or 100BASE-TX: Differential common driver transmit output (PMD Output Pair). These differential outputs are automatically configured to either 10BASE-T or 100BASE-TX
signaling.
TPTDM_A/FXTDM_A
Description
In Auto-MDIX mode of operation, this pair can be used as the Receive Input pair.
In 100BASE-FX mode, this pair becomes the 100BASE-FX
Transmit pair.
These pins require 3.3V bias for operation.
TPRDM_A/FXRDM_A
23
10BASE-T or 100BASE-TX or 100BASE-FX Receive Data
TPRDP_A/FXRDP_A
I/O
24
TPRDM_B/FXRDM_B
39
TPRDP_B/FXRDP_B
38
In 10BASE-T or 100BASE-TX: Differential receive input (PMD Input Pair). These differential inputs are automatically configured to
accept either 100BASE-TX or 10BASE-T signaling.
In Auto-MDIX mode of operation, this pair can be used as the
Transmit Output pair.
In 100BASE-FX mode, this pair becomes the 100BASE-FX
Receive pair.
These pins require 3.3V bias for operation.
FXSD_A
(LED_SPEED_A/AN1_A)
I
20
FXSD_B
(LED_SPEED_B/AN1_B)
FX Signal Detect: This pin provides the Signal Detect input for
100BASE-FX mode.
42
1.9 Special Connections
Signal Name
Type
Pin #
Description
RBIAS
I
32
Bias Resistor Connection. A 4.87 kΩ 1% resistor should be connected from RBIAS to GND.
PFBOUT
O
31
Power Feedback Output. Parallel caps, 10µ F and 0.1µF, should
be placed close to the PFBOUT. Connect this pin to PFBIN1 (pin
13), PFBIN2 (pin 27), PFBIN3 (pin35), PFBIN4 (pin 49). See
Section 5.5 for proper placement pin.
PFBIN1
I
7
Power Feedback Input. These pins are fed with power from
PFBOUT pin. A small capacitor of 0.1µF should be connected
close to each pin.
PFBIN2
28
PFBIN3
34
PFBIN4
54
Note: Do not supply power to these pins other than from
PFBOUT.
1.10 Power Supply Pins
Signal Name
Pin #
Description
IOVDD1, IOVDD2, IOVDD3,
IOVDD4
11,51,65,78
I/O 3.3V Supply
IOGND1, IOGND2,
IOGND3, IOGND4
10,52,64,77
I/O Ground
COREGND1, COREGND2
6,55
Core Ground
CDGND1, CDGND2
25,37
CD Ground
ANA33VDD
ANAGND1, ANAGND2,
ANAGND3, ANAGND4
30
22,29,33,40
Analog 3.3V Supply
Analog Ground
15
www.national.com
DP83849ID
1.8 10 Mb/s and 100 Mb/s PMD Interface
VHB80A Pin Pin Name
#
VHB80A Pin Pin Name
#
1
CRS_A/CRS_DV_A/LED_CFG_A
2
RX_ER_A/MDIX_EN_A
3
COL_A/FX_EN_A
4
RXD0_A/PHYAD1
5
RXD1_A/PHYAD2
6
COREGND1
7
PFBIN1
8
RXD2_A/CLK2MAC_DIS
9
RXD3_A/ED_EN_A
10
IOGND1
11
IOVDD1
12
TX_CLK_A
13
TX_EN_A
14
TXD0_A
15
TXD1_A
16
TXD2_A
17
TXD3_A/SNI_MODE_A
18
PWRDOWN_INT_A
19
LED_LINK_A/AN0_A
20
LED_SPEED_A/FXSD_A/AN1_A
21
LED_ACT/LED_COL/AN_EN_A
22
ANAGND1
23
TPRDM_A/FXRDM_A
24
TPRDP_A/FXRDP_A
25
CDGND1
26
TPTDM_A/FXTDM_A
27
TPTDP_A/FXTDP_A
28
PFBIN2
29
ANAGND2
30
ANA33VDD
31
PFBOUT
32
RBIAS
33
ANAGND3
34
PFBIN3
35
TPTDP_B/FXTDP_B
36
TPTDM_B/FXTDM_B
37
CDGND2
38
TPRDP_B/FXRDP_B
39
TPRDM_B/FXRDM_B
40
ANAGND4
41
LED_ACT/LED_COL/AN_EN_B
42
LED_SPEED_B/FXSD_B/AN1_B
DP83849ID
1.11 Package Pin Assignments
16
43
LED_LINK_B/AN0_B
44
PWRDOWN_INT_B
45
TXD3_B/SNI_MODE_B
46
TXD2_B
47
TXD1_B
48
TXD0_B
49
TX_EN_B
50
TX_CLK_B
51
IOVDD2
52
IOGND2
53
RXD3_B/ED_EN_B
54
PFBIN4
55
COREGND2
56
RXD2_B
57
RXD1_B/PHYAD4
58
RXD0_B/PHYAD3
59
COL_B/FX_EN_B
60
RX_ER_B/MDIX_EN_B
61
CRS_B/CRS_DV_B/LED_CFG_B
62
RX_DV_B/MII_MODE_B
63
RX_CLK_B
64
IOGND3
65
IOVDD3
66
MDIO
67
MDC
68
CLK2MAC
69
X2
70
X1
71
RESET_N
72
TCK
73
TDO
74
TMS
75
TRSTN
76
TDI
77
IOGND4
78
IOVDD4
79
RX_CLK_A
80
RX_DV_A/MII_MODE_A
www.national.com
This section includes information on the various configuration options available with the DP83849ID. The configuration options described below include:
—
—
—
—
—
—
—
Table 1. Auto-Negotiation Modes
Media Configuration
Auto-Negotiation
PHY Address and LEDs
Half Duplex vs. Full Duplex
Isolate mode
Loopback mode
BIST
AN_EN
AN1
AN0
0
0
0
10BASE-T, Half-Duplex
Forced Mode
0
0
1
10BASE-T, Full-Duplex
0
1
0
100BASE-TX, Half-Duplex
100BASE-TX, Full-Duplex
0
1
1
AN_EN
AN1
AN0
1
0
0
10BASE-T, Half/Full-Duplex
1
0
1
100BASE-TX, Half/Full-Duplex
1
1
0
10BASE-T Half-Duplex
2.1 Media Configuration
Advertised Mo0e
100BASE-TX, Half-Duplex
The DP83849ID supports both Twister Pair (100BASE-TX
and 10BASE-T) and Fiber (100BASE-FX) media. Each
port may be independently configured for Twisted Pair (TP)
or Fiber (FX) operation by strap option or by register
access.
At power-up/reset, the state of the COL_A and COL_B pins
will select the media for ports A and B respectively. The
default selection is TP mode, while an external pull-up will
select FX mode of operation. Strapping a port into FX
mode also automatically sets the Far-End Fault Enable, bit
3 of PCSR (16h), the Scramble Bypass, bit 1 of PCSR
(16h) and the Descrambler Bypass, bit 0 of PCSR (16h). In
addition, the media selection may be controlled by writing
to bit 6, FX_EN, of PCSR (16h).
2.2 Auto-Negotiation
The Auto-Negotiation function provides a mechanism for
exchanging configuration information between two ends of
a link segment and automatically selecting the highest performance mode of operation supported by both devices.
Fast Link Pulse (FLP) Bursts provide the signalling used to
communicate Auto-Negotiation abilities between two
devices at each end of a link segment. For further detail
regarding Auto-Negotiation, refer to Clause 28 of the IEEE
802.3u specification. The DP83849ID supports four different Ethernet protocols (10 Mb/s Half Duplex, 10 Mb/s Full
Duplex, 100 Mb/s Half Duplex, and 100 Mb/s Full Duplex),
so the inclusion of Auto-Negotiation ensures that the highest performance protocol will be selected based on the
advertised ability of the Link Partner. The Auto-Negotiation
function within the DP83849ID can be controlled either by
internal register access or by the use of the AN_EN, AN1
and AN0 pins.
2.2.1 Auto-Negotiation Pin Control
The state of AN_EN, AN0 and AN1 determines whether the
DP83849ID is forced into a specific mode or Auto-Negotiation will advertise a specific ability (or set of abilities) as
given in Table 1. These pins allow configuration options to
be selected without requiring internal register access.
The state of AN_EN, AN0 and AN1, upon power-up/reset,
determines the state of bits [8:5] of the ANAR register.
The Auto-Negotiation function selected at power-up or
reset can be changed at any time by writing to the Basic
Mode Control Register (BMCR) at address 00h.
1
1
1
10BASE-T, Half/Full-Duplex
100BASE-TX, Half/Full-Duplex
2.2.2 Auto-Negotiation Register Control
When Auto-Negotiation is enabled, the DP83849ID transmits the abilities programmed into the Auto-Negotiation
Advertisement register (ANAR) at address 04h via FLP
Bursts. Any combination of 10 Mb/s, 100 Mb/s, HalfDuplex, and Full Duplex modes may be selected.
Auto-Negotiation Priority Resolution:
— (1) 100BASE-TX Full Duplex (Highest Priority)
— (2) 100BASE-TX Half Duplex
— (3) 10BASE-T Full Duplex
— (4) 10BASE-T Half Duplex (Lowest Priority)
The Basic Mode Control Register (BMCR) at address 00h
provides control for enabling, disabling, and restarting the
Auto-Negotiation process. When Auto-Negotiation is disabled, the Speed Selection bit in the BMCR controls
switching between 10 Mb/s or 100 Mb/s operation, and the
Duplex Mode bit controls switching between full duplex
operation and half duplex operation. The Speed Selection
and Duplex Mode bits have no effect on the mode of operation when the Auto-Negotiation Enable bit is set.
The Link Speed can be examined through the PHY Status
Register (PHYSTS) at address 10h after a Link is
achieved.
The Basic Mode Status Register (BMSR) indicates the set
of available abilities for technology types, Auto-Negotiation
ability, and Extended Register Capability. These bits are
permanently set to indicate the full functionality of the
DP83849ID (only the 100BASE-T4 bit is not set since the
DP83849ID does not support that function).
The BMSR also provides status on:
— Whether or not Auto-Negotiation is complete
— Whether or not the Link Partner is advertising that a remote fault has occurred
— Whether or not valid link has been established
— Support for Management Frame Preamble suppression
The Auto-Negotiation Advertisement Register (ANAR) indicates the Auto-Negotiation abilities to be advertised by the
DP83849ID. All available abilities are transmitted by
default, but any ability can be suppressed by writing to the
17
www.national.com
DP83849ID
2.0 Configuration
The Auto-Negotiation Link Partner Ability Register
(ANLPAR) at address 05h is used to receive the base link
code word as well as all next page code words during the
negotiation. Furthermore, the ANLPAR will be updated to
either 0081h or 0021h for parallel detection to either 100
Mb/s or 10 Mb/s respectively.
2.2.5 Enabling Auto-Negotiation via Software
It is important to note that if the DP83849ID has been initialized upon power-up as a non-auto-negotiating device
(forced technology), and it is then required that Auto-Negotiation or re-Auto-Negotiation be initiated via software,
bit 12 (Auto-Negotiation Enable) of the Basic Mode Control
Register (BMCR) must first be cleared and then set for any
Auto-Negotiation function to take effect.
The Auto-Negotiation Expansion Register (ANER) indicates additional Auto-Negotiation status. The ANER provides status on:
2.2.6 Auto-Negotiation Complete Time
— Whether or not a Parallel Detect Fault has occurred
— Whether or not the Link Partner supports the Next Page
function
— Whether or not the DP83849ID supports the Next Page
function
— Whether or not the current page being exchanged by
Auto-Negotiation has been received
— Whether or not the Link Partner supports Auto-Negotiation
Refer to Clause 28 of the IEEE 802.3u standard for a full
description of the individual timers related to Auto-Negotiation.
Parallel detection and Auto-Negotiation take approximately
2-3 seconds to complete. In addition, Auto-Negotiation with
next page should take approximately 2-3 seconds to complete, depending on the number of next pages sent.
2.3 Auto-MDIX
When enabled, this function utilizes Auto-Negotiation to
determine the proper configuration for transmission and
2.2.3 Auto-Negotiation Parallel Detection
reception of data and subsequently selects the appropriate
The DP83849ID supports the Parallel Detection function as MDI pair for MDI/MDIX operation. The function uses a randefined in the IEEE 802.3u specification. Parallel Detection dom seed to control switching of the crossover circuitry.
requires both the 10 Mb/s and 100 Mb/s receivers to moni- This implementation complies with the corresponding IEEE
tor the receive signal and report link status to the Auto- 802.3 Auto-Negotiation and Crossover Specifications.
Negotiation function. Auto-Negotiation uses this informa- Auto-MDIX is enabled by default and can be configured via
tion to configure the correct technology in the event that the strap or via PHYCR (19h) register, bits [15:14].
Link Partner does not support Auto-Negotiation but is Neither Auto-Negotiation nor Auto-MDIX is required to be
transmitting link signals that the 100BASE-TX or 10BASEenabled in forcing crossover of the MDI pairs. Forced
T PMAs recognize as valid link signals.
crossover can be achieved through the FORCE_MDIX bit,
If the DP83849ID completes Auto-Negotiation as a result of bit 14 of PHYCR (19h) register.
Parallel Detection, bits 5 and 7 within the ANLPAR register Note: Auto-MDIX will not work in a forced mode of operawill be set to reflect the mode of operation present in the tion.
Link Partner. Note that bits 4:0 of the ANLPAR will also be
set to 00001 based on a successful parallel detection to
indicate a valid 802.3 selector field. Software may determine that negotiation completed via Parallel Detection by 2.4 PHY Address
reading a zero in the Link Partner Auto-Negotiation Able bit The 4 PHY address inputs pins are shown below.
once the Auto-Negotiation Complete bit is set. If configured
for parallel detect mode and any condition other than a sinTable 2. PHY Address Mapping
gle good link occurs then the parallel detect fault bit will be
set.
Pin #
PHYAD Function
RXD Function
2.2.4 Auto-Negotiation Restart
4
PHYAD1
RXD0_A
5
PHYAD2
RXD1_A
Once Auto-Negotiation has completed, it may be restarted
58
PHYAD3
RXD0_B
at any time by setting bit 9 (Restart Auto-Negotiation) of the
57
PHYAD4
RXD1_B
BMCR to one. If the mode configured by a successful AutoNegotiation loses a valid link, then the Auto-Negotiation
process will resume and attempt to determine the configu- The DP83849ID provides four address strap pins for deterration for the link. This function ensures that a valid config- mining the PHY addresses for ports A and B of the device.
The 4 address strap pins provide the upper four bits of the
uration is maintained if the cable becomes disconnected.
PHY address. The lowest bit of the PHY address is depenA renegotiation request from any entity, such as a manage- dent on the port. Port A has a value of 0 for the PHY
ment agent, will cause the DP83849ID to halt any transmit address bit 0 while port B has a value of 1. The PHY
data and link pulse activity until the break_link_timer address strap input pins are shown in Table 2.
expires (~1500 ms). Consequently, the Link Partner will go
into link fail and normal Auto-Negotiation resumes. The The PHY address strap information is latched into the
DP83849ID will resume Auto-Negotiation after the PHYCR register (address 19h, bits [4:0]) at device powerbreak_link_timer has expired by issuing FLP (Fast Link up and hardware reset. The PHY Address pins are shared
with the RXD pins. Each DP83849ID or port sharing an
Pulse) bursts.
18
www.national.com
DP83849ID
ANAR. Updating the ANAR to suppress an ability is one
way for a management agent to change (restrict) the technology that is used.
The DP83849ID supports PHY Address strapping of Port A
to even values 0 (<0000_0>) through 30 (<1111_0>). Port
B is strapped to odd values 1 (<0000_1>) through 31
(<1111_1>). Note that Port B address is always 1 greater
than Port A address.
For further detail relating to the latch-in timing requirements
of the PHY Address pins, as well as the other hardware
configuration pins, refer to the Reset summary in
Section 6.0.
The DP83849ID can be put into MII Isolate mode by writing
to bit 10 of the BMCR register.
When in the MII isolate mode, the DP83849ID does not
respond to packet data present at TXD[3:0], TX_EN inputs
and presents a high impedance on the TX_CLK, RX_CLK,
RX_DV, RX_ER, RXD[3:0], COL, and CRS outputs. When
in Isolate mode, the DP83849ID will continue to respond to
all management transactions.
While in Isolate mode, the PMD output pair will not transmit
packet data but will continue to source 100BASE-TX
scrambled idles or 10BASE-T normal link pulses.
RXD0_A
The DP83849ID can Auto-Negotiate or parallel detect to a
specific technology depending on the receive signal at the
PMD input pair. A valid link can be established for the
receiver even when the DP83849ID is in Isolate mode.
RXD1_A
RXD0_B
PHYAD4= 0 PHYAD3 = 0 PHYAD2 = 0 PHYAD1 = 1
2.2kΩ
RXD1_B
Refer to Figure 2 for an example of a PHYAD connection to
external components. In this example, the PHYAD strapping results in address 00010 (02h) for Port A and address
00011 (03h) for Port B.
2.4.1 MII Isolate Mode
VCC
Figure 2. PHYAD Strapping Example
19
www.national.com
DP83849ID
MDIO bus in a system must have a unique physical
address.
The DP83849ID supports three configurable Light Emitting
Diode (LED) pins for each port.
Several functions can be multiplexed onto the three LEDs
using three different modes of operation. The LED operation mode can be selected by writing to the LED_CFG[1:0]
register bits in the PHY Control Register (PHYCR) at
address 19h, bits [6:5]. In addition, LED_CFG[0] for each
port can be set by a strap option on the CRS_A and
CRS_B pins. LED_CFG[1] is only controllable through register access and cannot be set by as strap pin.
See Table 3 for LED Mode selection.
Table 3. LED Mode Select
Mode
LED_CFG[1]
LED_CFG[0]
1
don’t care
1
2
0
0
3
1
0
LED_LINK
LED_SPEED
ON for Good Link
ON in 100 Mb/s
ON for Activity
OFF for No Link
OFF in 10 Mb/s
OFF for No Activity
ON for Good Link
ON in 100 Mb/s
ON for Collision
BLINK for Activity
OFF in 10 Mb/s
OFF for No Collision
ON for Good Link
ON in 100 Mb/s
ON for Full Duplex
BLINK for Activity
OFF in 10 Mb/s
OFF for Half Duplex
The LED_LINK pin in Mode 1 indicates the link status of
the port. In 100BASE-T mode, link is established as a
result of input receive amplitude compliant with the TPPMD specifications which will result in internal generation
of signal detect. A 10 Mb/s Link is established as a result of
the reception of at least seven consecutive normal Link
Pulses or the reception of a valid 10BASE-T packet. This
will cause the assertion of LED_LINK. LED_LINK will deassert in accordance with the Link Loss Timer as specified in
the IEEE 802.3 specification.
The LED_LINK pin in Mode 1 will be OFF when no LINK is
present.
LED_ACT/LED_COL
The LED_ACT/LED_COL pin in Mode 3 indicates Duplex
status for 10 Mb/s or 100 Mb/s operation. The LED will be
ON for Full Duplex and OFF for Half Duplex.
In 10 Mb/s half duplex mode, the collision LED is based on
the COL signal.
Since these LED pins are also used as strap options, the
polarity of the LED is dependent on whether the pin is
pulled up or down.
2.5.1 LEDs
The LED_LINK pin in Mode 2 and Mode 3 will be ON to Since the Auto-Negotiation (AN) strap options share the
indicate Link is good and BLINK to indicate activity is LED output pins, the external components required for
present on activity. The BLINK frequency is defined in strapping and LED usage must be considered in order to
avoid contention.
BLINK_FREQ, bits [7:6] of register LEDCR (18h).
Specifically, when the LED outputs are used to drive LEDs
directly, the active state of each output driver is dependent
on the logic level sampled by the corresponding AN input
upon power-up/reset. For example, if a given AN input is
resistively pulled low then the corresponding output will be
The LED_SPEED pin indicates 10 or 100 Mb/s data rate of
the port. The LED is ON when operating in 100Mb/s mode configured as an active high driver. Conversely, if a given
and OFF when operating in 10Mb/s mode. The functional- AN input is resistively pulled high, then the corresponding
output will be configured as an active low driver.
ity of this LED is independent of mode selected.
The LED_ACT/LED_COL pin in Mode 1 indicates the pres- Refer to Figure 3 for an example of AN connections to
external components at port A. In this example, the AN
ence of either transmit or receive activity. The LED will be
ON for Activity and OFF for No Activity. In Mode 2, this pin strapping results in Auto-Negotiation disabled with 100
indicates the Collision status of the port. The LED will be Full-Duplex forced.
Activity is defined as configured in LEDACT_RX, bit 8 of
register LEDCR (18h). If LEDACT_RX is 0, Activity is signaled for either transmit or receive. If LEDACT_RX is 1,
Activity is only signaled for receive.
ON for Collision and OFF for No Collision.
The adaptive nature of the LED outputs helps to simplify
potential implementation issues of these dual purpose pins.
20
www.national.com
DP83849ID
2.5 LED Interface
LED_LINK_A
LED_SPEED_A
165Ω
AN0_A = 1
165Ω
LED_ACT/LED_COL_A
165Ω
2.2kΩ
AN1_A = 1
Auto-Negotiation is not supported in 100BASE-FX operation. Selection of Half or Full-duplex operation is controlled
by bit 8 of the Basic Mode Control Register (BMCR),
address 00h. If 100BASE-FX mode is strapped using the
FX_EN pin, the AN0 strap value is used to set the value of
bit 8 of the BMCR (00h) register. Note that the other AutoNegotiation strap pins (AN_EN and AN1) are ignored in
100BASE-FX mode.
2.7 Internal Loopback
VCC
The DP83849ID includes a Loopback Test mode for facilitating system diagnostics. The Loopback mode is selected
through bit 14 (Loopback) of the Basic Mode Control Register (BMCR). Writing 1 to this bit enables MII transmit data
to be routed to the MII receive outputs. Loopback status
may be checked in bit 3 of the PHY Status Register
(PHYSTS). While in Loopback mode the data will not be
transmitted onto the media. To ensure that the desired
operating mode is maintained, Auto-Negotiation should be
disabled before selecting the Loopback mode.
GND
Figure 3. AN Strapping and LED Loading Example
2.5.2 LED Direct Control
The DP83849ID provides another option to directly control
any or all LED outputs through the LED Direct Control Register (LEDCR), address 18h. The register does not provide
read access to LEDs.
2.6 Half Duplex vs. Full Duplex
The DP83849ID supports both half and full duplex operation at both 10 Mb/s and 100 Mb/s speeds.
2.8 BIST
The DP83849ID incorporates an internal Built-in Self Test
(BIST) circuit to accommodate in-circuit testing or diagnostics. The BIST circuit can be utilized to test the integrity of
the transmit and receive data paths. BIST testing can be
performed with the part in the internal loopback mode or
externally looped back using a loopback cable fixture.
The BIST is implemented with independent transmit and
Half-duplex relies on the CSMA/CD protocol to handle collireceive paths, with the transmit block generating a continusions and network access. In Half-Duplex mode, CRS
ous stream of a pseudo random sequence. The user can
responds to both transmit and receive activity in order to
select a 9 bit or 15 bit pseudo random sequence from the
maintain compliance with the IEEE 802.3 specification.
PSR_15 bit in the PHY Control Register (PHYCR). The
Since the DP83849ID is designed to support simultaneous received data is compared to the generated pseudo-rantransmit and receive activity it is capable of supporting full- dom data by the BIST Linear Feedback Shift Register
duplex switched applications with a throughput of up to 200 (LFSR) to determine the BIST pass/fail status.
Mb/s per port when operating in either 100BASE-TX or
The pass/fail status of the BIST is stored in the BIST status
100BASE-FX. Because the CSMA/CD protocol does not
bit in the PHYCR register. The status bit defaults to 0 (BIST
apply to full-duplex operation, the DP83849ID disables its
fail) and will transition on a successful comparison. If an
own internal collision sensing and reporting functions and
error (mis-compare) occurs, the status bit is latched and is
modifies the behavior of Carrier Sense (CRS) such that it
cleared upon a subsequent write to the Start/Stop bit.
indicates only receive activity. This allows a full-duplex
For transmit VOD testing, the Packet BIST Continuous
capable MAC to operate properly.
Mode can be used to allow continuous data transmission,
All modes of operation (100BASE-TX, 100BASE-FX,
setting BIST_CONT_MODE, bit 5, of CDCTRL1 (1Bh).
10BASE-T) can run either half-duplex or full-duplex. Additionally, other than CRS and Collision reporting, all remain- The number of BIST errors can be monitored through the
ing MII signaling remains the same regardless of the BIST Error Count in the CDCTRL1 (1Bh), bits [15:8].
selected duplex mode.
21
www.national.com
DP83849ID
AN_EN_A
=0
It is important to understand that while Auto-Negotiation
with the use of Fast Link Pulse code words can interpret
and configure to full-duplex operation, parallel detection
can not recognize the difference between full and halfduplex from a fixed 10 Mb/s or 100 Mb/s link partner over
twisted pair. As specified in the 802.3u specification, if a
far-end link partner is configured to a forced full duplex
100BASE-TX ability, the parallel detection state machine in
the partner would be unable to detect the full duplex capability of the far-end link partner. This link segment would
negotiate to a half duplex 100BASE-TX configuration
(same scenario for 10Mb/s).
The DP83849ID supports several modes of operation
using the MII interface pins. The options are defined in the
following sections and include:
— MII Mode
— RMII Mode
— 10 Mb Serial Network Interface (SNI)
In addition, the DP83849ID supports the standard 802.3u
MII Serial Management Interface.
The modes of operation can be selected by strap options
or register control. For RMII mode, it is recommended to
use the strap option, since it requires a 50 MHz clock
instead of the normal 25 MHz.
In each of these modes, the IEEE 802.3 serial management interface is operational for device configuration and
status. The serial management interface of the MII allows
for the configuration and control of multiple PHY devices,
gathering of status, error information, and the determination of the type and capabilities of the attached PHY(s).
3.1 MII Interface
The transmit interface consists of a nibble wide data bus
TXD[3:0], a transmit enable control signal TX_EN, and a
transmit clock TX_CLK which runs at either 2.5 MHz or 25
MHz.
Additionally, the MII includes the carrier sense signal CRS,
as well as a collision detect signal COL. The CRS signal
asserts to indicate the reception of data from the network
or as a function of transmit data in Half Duplex mode. The
COL signal asserts as an indication of a collision which can
occur during half-duplex operation when both a transmit
and receive operation occur simultaneously.
3.1.2 Collision Detect
For Half Duplex, a 10BASE-T or 100BASE-TX collision is
detected when the receive and transmit channels are
active simultaneously. Collisions are reported by the COL
signal on the MII.
If the DP83849ID is transmitting in 10 Mb/s mode when a
collision is detected, the collision is not reported until seven
bits have been received while in the collision state. This
prevents a collision being reported incorrectly due to noise
on the network. The COL signal remains set for the duration of the collision.
The DP83849ID incorporates the Media Independent Interface (MII) as specified in Clause 22 of the IEEE 802.3u
standard. This interface may be used to connect PHY
devices to a MAC in 10/100 Mb/s systems. This section
describes the nibble wide MII data interface.
If a collision occurs during a receive operation, it is immediately reported by the COL signal.
3.1.1 Nibble-wide MII Data Interface
3.1.3 Carrier Sense
Clause 22 of the IEEE 802.3u specification defines the
Media Independent Interface. This interface includes a
dedicated receive bus and a dedicated transmit bus. These
two data buses, along with various control and status signals, allow for the simultaneous exchange of data between
the DP83849ID and the upper layer agent (MAC).
Carrier Sense (CRS) is asserted due to receive activity,
once valid data is detected via the squelch function during
10 Mb/s operation. During 100 Mb/s operation CRS is
asserted when a valid link (SD) and two non-contiguous
zeros are detected on the line.
The receive interface consists of a nibble wide data bus
RXD[3:0], a receive error signal RX_ER, a receive data
valid flag RX_DV, and a receive clock RX_CLK for synchronous transfer of the data. The receive clock operates
at either 2.5 MHz to support 10 Mb/s operation modes or at
25 MHz to support 100 Mb/s operational modes.
For 10 or 100 Mb/s Full Duplex operation, CRS is asserted
only due to receive activity.
When heartbeat is enabled (only applicable to 10 Mb/s
operation), approximately 1µs after the transmission of
each packet, a Signal Quality Error (SQE) signal of approxThe nibble wide MII data interface consists of a receive bus imately 10 bit times is generated (internally) to indicate
and a transmit bus each with control signals to facilitate successful transmission. SQE is reported as a pulse on the
data transfer between the PHY and the upper layer (MAC). COL signal of the MII.
For 10 or 100 Mb/s Half Duplex operation, CRS is asserted
during either packet transmission or reception.
CRS is deasserted following an end of packet.
22
www.national.com
DP83849ID
3.0 MAC Interface
The DP83849ID incorporates the Reduced Media Independent Interface (RMII) as specified in the RMII specification
(rev1.2) from the RMII Consortium. This interface may be
used to connect PHY devices to a MAC in 10/100 Mb/s
systems using a reduced number of pins. In this mode,
data is transferred 2-bits at a time using the 50 MHz
RMII_REF clock for both transmit and receive. The following pins are used in RMII mode:
— TX_EN
— TXD[1:0]
— RX_ER (optional for Mac)
— CRS_DV
— RXD[1:0]
— X1 (RMII Reference clock is 50 MHz)
In addition, the RMII mode supplies an RX_DV signal
which allows for a simpler method of recovering receive
data without having to separate RX_DV from the CRS_DV
indication. This is especially useful for diagnostic testing
where it may be desirable to externally loop Receive MII
data directly to the transmitter.
The RX_ER output may be used by the MAC to detect
error conditions. It is asserted for symbol errors received
during a packet, False Carrier events, and also for FIFO
underrun or overrun conditions. Since the Phy is required
to corrupt receive data on an error, a MAC is not required
to use RX_ER.
It is important to note that since both digital channels in the
DP83849ID share the X1/RMII_REF input, both channels
must have RMII mode enabled or both channels must have
RMII mode disabled. Either channel may be in 10Mb or
100Mb mode in RMII or non-RMII mode.
Since the reference clock operates at 10 times the data
rate for 10 Mb/s operation, transmit data is sampled every
10 clocks. Likewise, receive data will be generated every
10th clock so that an attached device can sample the data
every 10 clocks.
RMII mode requires a 50 MHz oscillator be connected to
the device X1 pin. A 50 MHz crystal is not supported.
To tolerate potential frequency differences between the 50
MHz reference clock and the recovered receive clock, the
receive RMII function includes a programmable elasticity
buffer. The elasticity buffer is programmable to minimize
propagation delay based on expected packet size and
clock accuracy. This allows for supporting a range of
packet sizes including jumbo frames.
The elasticity buffer will force Frame Check Sequence
errors for packets which overrun or underrun the FIFO.
Underrun and Overrun conditions can be reported in the
RMII and Bypass Register (RBR). The following table indicates how to program the elasticity buffer fifo (in 4-bit increments) based on expected max packet size and clock
accuracy. It assumes both clocks (RMII Reference clock
and far-end Transmitter clock) have the same accuracy.
Packet lengths can be scaled linearly based on accuracy
(+/- 25ppm would allows packets twice as large). If the
threshold setting must support both 10Mb and 100Mb
operation, the setting should be made to support both
speeds.
Table 4. Supported packet sizes at +/-50ppm frequency accuracy
Start Threshold
Latency Tolerance
Recommended Packet Size
RBR[1:0]
at +/- 50ppm
100Mb
10Mb
100Mb
10Mb
01 (default)
2 bits
8 bits
2,400 bytes
9,600 bytes
10
6 bits
4 bits
7,200 bytes
4,800 bytes
11
10 bits
8 bits
12,000 bytes
9,600 bytes
00
14 bits
12 bits
16,800 bytes
14,400 bytes
3.3 10 Mb Serial Network Interface (SNI)
The DP83849ID incorporates a 10 Mb Serial Network Interface (SNI) which allows a simple serial data interface for 10
Mb only devices. This is also referred to as a 7-wire interface. While there is no defined standard for this interface, it
is based on early 10 Mb physical layer devices. Data is
clocked serially at 10 MHz using separate transmit and
receive paths. The following pins are used in SNI mode:
—
—
—
—
—
—
TX_EN
TXD[0]
RX_CLK
RXD[0]
CRS
COL
— TX_CLK
23
www.national.com
DP83849ID
3.2 Reduced MII Interface
The DP83849ID waits until it has received this preamble
sequence before responding to any other transaction.
Once the DP83849ID serial management port has been
3.4.1 Serial Management Register Access
initialized no further preamble sequencing is required until
The serial management MII specification defines a set of after a power-on/reset, invalid Start, invalid Opcode, or
thirty-two 16-bit status and control registers that are acces- invalid turnaround bit has occurred.
sible through the management interface pins MDC and
MDIO. The DP83849ID implements all the required MII The Start code is indicated by a <01> pattern. This assures
registers as well as several optional registers. These regis- the MDIO line transitions from the default idle line state.
ters are fully described in Section 7.0. A description of the Turnaround is defined as an idle bit time inserted between
serial management access protocol follows.
the Register Address field and the Data field. To avoid contention during a read transaction, no device shall actively
drive the MDIO signal during the first bit of Turnaround.
The addressed DP83849ID drives the MDIO with a zero for
3.4.2 Serial Management Access Protocol
the second bit of turnaround and follows this with the
The serial control interface consists of two pins, Manage- required data. Figure 4 shows the timing relationship
ment Data Clock (MDC) and Management Data Input/Out- between MDC and the MDIO as driven/received by the Staput (MDIO). MDC has a maximum clock rate of 25 MHz tion (STA) and the DP83849ID (PHY) for a typical register
and no minimum rate. The MDIO line is bi-directional and read access.
may be shared by up to 32 devices. The MDIO frame forFor write transactions, the station management entity
mat is shown below in Table 5.
writes data to the addressed DP83849ID thus eliminating
In addition, the MDIO pin requires a pull-up resistor (1.5 the requirement for MDIO Turnaround. The Turnaround
kΩ) which, during IDLE and turnaround, will pull MDIO time is filled by the management entity by inserting <10>.
high. In order to initialize the MDIO interface, the station Figure 5 shows the timing relationship for a typical MII regmanagement entity sends a sequence of 32 contiguous ister write access.
logic ones on MDIO to provide the DP83849ID with a
sequence that can be used to establish synchronization.
This preamble may be generated either by driving MDIO
high for 32 consecutive MDC clock cycles, or by simply
allowing the MDIO pull-up resistor to pull the MDIO pin high
during which time 32 MDC clock cycles are provided. In
addition 32 MDC clock cycles should be used to re-sync
the device if an invalid start, opcode, or turnaround bit is
detected.
Table 5. Typical MDIO Frame Format
MII Management
Serial Protocol
<idle><start><op code><device addr><reg addr><turnaround><data><idle>
Read Operation
<idle><01><10><AAAAA><RRRRR><Z0><xxxx xxxx xxxx xxxx><idle>
Write Operation
<idle><01><01><AAAAA><RRRRR><10><xxxx xxxx xxxx xxxx><idle>
MDC
MDIO
Z
Z
(STA)
Z
MDIO
Z
(PHY)
Z
Idle
0 1 1 0 0 1 1 0 0 0 0 0 0 0
Start
Opcode
(Read)
PHY Address
(PHYAD = 0Ch)
Register Address
(00h = BMCR)
Z
0 0 0 1 1 0 0 0 1 0 0 0 0 0 0 0 0
TA
Register Data
Z
Idle
Figure 4. Typical MDC/MDIO Read Operation
24
www.national.com
DP83849ID
3.4 802.3u MII Serial Management Interface
DP83849ID
MDC
MDIO
Z
Z
(STA)
Z
Idle
0 1 0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Start
Opcode
(Write)
PHY Address
(PHYAD = 0Ch)
Register Address
(00h = BMCR)
TA
Register Data
Z
Idle
Figure 5. Typical MDC/MDIO Write Operation
3.4.3 Serial Management Preamble Suppression
The DP83849ID supports a Preamble Suppression mode
as indicated by a one in bit 6 of the Basic Mode Status
Register (BMSR, address 01h.) If the station management
entity (i.e. MAC or other management controller) determines that all PHYs in the system support Preamble Suppression by returning a one in this bit, then the station
management entity need not generate preamble for each
management transaction.
The DP83849ID requires a single initialization sequence of
32 bits of preamble following hardware/software reset. This
requirement is generally met by the mandatory pull-up
resistor on MDIO in conjunction with a continuous MDC, or
the management access made to determine whether Preamble Suppression is supported.
While the DP83849ID requires an initial preamble
sequence of 32 bits for management initialization, it does
not require
a full 32-bit sequence between each subsequent transaction. A minimum of one idle bit between management
transactions is required as specified in the IEEE 802.3u
specification.
3.4.4 Simultaneous Register Write
The DP83849ID incorporates a mode which allows simultaneous write access to both Port A and B register blocks at
the same time. This mode is selected by setting bit 15 of
RMII and Bypass Register (RBR, address 17h) in Port A.
As long as this bit remains set, subsequent writes to Port A
will write to registers in both ports.
Register reads are unaffected. Each port must still be read
individually.
25
www.national.com
The block diagram in Figure 6. provides an overview of
each functional block within the 100BASE-TX transmit section.
This section describes the operations within each transceiver module, 100BASE-TX and 10BASE-T. Each operation consists of several functional blocks and described in The Transmitter section consists of the following functional
blocks:
the following:
— Code-group Encoder and Injection block
— 100BASE-TX Transmitter
— Scrambler block (bypass option)
— 100BASE-TX Receiver
— NRZ to NRZI encoder block
— 100BASE-FX Operation
— Binary to MLT-3 converter / Common Driver
— 10BASE-T Transceiver Module
The bypass option for the functional blocks within the
100BASE-TX transmitter provides flexibility for applications
where data conversion is not always required. The
4.1 100BASE-TX TRANSMITTER
DP83849ID implements the 100BASE-TX transmit state
The 100BASE-TX transmitter consists of several functional machine diagram as specified in the IEEE 802.3u Stanblocks which convert synchronous 4-bit nibble data, as pro- dard, Clause 24.
vided by the MII, to a scrambled MLT-3 125 Mb/s serial
data stream. Because the 100BASE-TX TP-PMD is integrated, the differential output pins, PMD Output Pair, can
be directly routed to the magnetics.
TX_CLK
TXD[3:0] /
TX_EN
DIVIDE
BY 5
4B5B CODEGROUP
ENCODER &
5B PARALLEL
TO SERIAL
125MHZ CLOCK
SCRAMBLER
MUX
BP_SCR
100BASE-TX
LOOPBACK
MLT[1:0]
NRZ TO NRZI
ENCODER
BINARY
TO MLT-3 /
COMMON
DRIVER
PMD OUTPUT PAIR
Figure 6. 100BASE-TX Transmit Block Diagram
26
www.national.com
DP83849ID
4.0 Architecture
DP83849ID
Table 13. 4B5B Code-Group Encoding/Decoding
DATA CODES
0
11110
0000
1
01001
0001
2
10100
0010
3
10101
0011
4
01010
0100
5
01011
0101
6
01110
0110
7
01111
0111
8
10010
1000
9
10011
1001
A
10110
1010
B
10111
1011
C
11010
1100
D
11011
1101
E
11100
1110
F
11101
1111
IDLE AND CONTROL CODES
H
00100
HALT code-group - Error code
I
11111
Inter-Packet IDLE - 0000 (Note 1)
J
11000
First Start of Packet - 0101 (Note 1)
K
10001
Second Start of Packet - 0101 (Note 1)
T
01101
First End of Packet - 0000 (Note 1)
R
00111
Second End of Packet - 0000 (Note 1)
INVALID CODES
V
00000
V
00001
V
00010
V
00011
V
00101
V
00110
V
01000
V
01100
Note: Control code-groups I, J, K, T and R in data fields will be mapped as invalid codes, together with RX_ER asserted.
27
www.national.com
The code-group encoder converts 4-bit (4B) nibble data
generated by the MAC into 5-bit (5B) code-groups for
transmission. This conversion is required to allow control
data to be combined with packet data code-groups. Refer
to Table 13 for 4B to 5B code-group mapping details.
The code-group encoder substitutes the first 8-bits of the
MAC preamble with a J/K code-group pair (11000 10001)
upon transmission. The code-group encoder continues to
replace subsequent 4B preamble and data nibbles with
corresponding 5B code-groups. At the end of the transmit
packet, upon the deassertion of Transmit Enable signal
from the MAC, the code-group encoder injects the T/R
code-group pair (01101 00111) indicating the end of the
frame.
transmit transformer primary winding, resulting in a MLT-3
signal.
The 100BASE-TX MLT-3 signal sourced by the PMD Output Pair common driver is slew rate controlled. This should
be considered when selecting AC coupling magnetics to
ensure TP-PMD Standard compliant transition times (3 ns
< Tr < 5 ns).
The 100BASE-TX transmit TP-PMD function within the
DP83849ID is capable of sourcing only MLT-3 encoded
data. Binary output from the PMD Output Pair is not possible in 100 Mb/s mode.
4.2 100BASE-TX RECEIVER
The 100BASE-TX receiver consists of several functional
After the T/R code-group pair, the code-group encoder
blocks which convert the scrambled MLT-3 125 Mb/s serial
continuously injects IDLEs into the transmit data stream data stream to synchronous 4-bit nibble data that is prountil the next transmit packet is detected (reassertion of
vided to the MII. Because the 100BASE-TX TP-PMD is
Transmit Enable).
integrated, the differential input pins, RD±, can be directly
routed from the AC coupling magnetics.
4.1.2 Scrambler
The scrambler is required to control the radiated emissions
at the media connector and on the twisted pair cable (for
100BASE-TX applications). By scrambling the data, the
total energy launched onto the cable is randomly distributed over a wide frequency range. Without the scrambler,
energy levels at the PMD and on the cable could peak
beyond FCC limitations at frequencies related to repeating
5B sequences (i.e., continuous transmission of IDLEs).
See Figure 7 for a block diagram of the 100BASE-TX
receive function. This provides an overview of each functional block within the 100BASE-TX receive section.
The Receive section consists of the following functional
blocks:
—
—
—
—
The scrambler is configured as a closed loop linear feed—
back shift register (LFSR) with an 11-bit polynomial. The
output of the closed loop LFSR is X-ORd with the serial —
NRZ data from the code-group encoder. The result is a —
scrambled data stream with sufficient randomization to —
decrease radiated emissions at certain frequencies by as
much as 20 dB. The DP83849ID uses the PHY_ID (pins —
—
PHYAD [4:1]) to set a unique seed value.
—
Analog Front End
Digital Signal Processor
Signal Detect
MLT-3 to Binary Decoder
NRZI to NRZ Decoder
Serial to Parallel
Descrambler
Code Group Alignment
4B/5B Decoder
Link Integrity Monitor
Bad SSD Detection
4.1.3 NRZ to NRZI Encoder
After the transmit data stream has been serialized and
scrambled, the data must be NRZI encoded in order to
comply with the TP-PMD standard for 100BASE-TX transmission over Category-5 Unshielded twisted pair cable.
4.2.1 Analog Front End
In addition to the Digital Equalization and Gain Control, the
DP83849ID includes Analog Equalization and Gain Control
in the Analog Front End. The Analog Equalization reduces
the amount of Digital Equalization required in the DSP.
4.1.4 Binary to MLT-3 Convertor
The Binary to MLT-3 conversion is accomplished by converting the serial binary data stream output from the NRZI
encoder into two binary data streams with alternately
phased logic one events. These two binary streams are
then fed to the twisted pair output driver which converts the
voltage to current and alternately drives either side of the
4.2.2 Digital Signal Processor
The Digital Signal Processor includes Adaptive Equalization with Gain Control and Base Line Wander Compensation.
28
www.national.com
DP83849ID
4.1.1 Code-group Encoding and Injection
RX_CLK
DP83849ID
RX_DV/CRS
RXD[3:0] / RX_ER
4B/5B DECODER
SERIAL TO
PARALLEL
CODE GROUP
ALIGNMENT
LINK
INTEGRITY
MONITOR
RX_DATA VALID
SSD DETECT
DESCRAMBLER
NRZI TO NRZ
DECODER
MLT-3 TO BINARY
DECODER
SIGNAL
DETECT
DIGITAL
SIGNAL
PROCESSOR
ANALOG
FRONT
END
RD +/−
Figure 7. 100BASE-TX Receive Block Diagram
29
www.national.com
When transmitting data at high speeds over copper twisted
pair cable, frequency dependent attenuation becomes a
concern. In high-speed twisted pair signalling, the frequency content of the transmitted signal can vary greatly
during normal operation based primarily on the randomness of the scrambled data stream. This variation in signal
attenuation caused by frequency variations must be compensated to ensure the integrity of the transmission.
In order to ensure quality transmission when employing
MLT-3 encoding, the compensation must be able to adapt
to various cable lengths and cable types depending on the
installed environment. The selection of long cable lengths
for a given implementation, requires significant compensation which will over-compensate for shorter, less attenuating lengths. Conversely, the selection of short or
intermediate cable lengths requiring less compensation will
cause serious under-compensation for longer length
cables. The compensation or equalization must be adap-
tive to ensure proper conditioning of the received signal
independent of the cable length.
The DP83849ID utilizes an extremely robust equalization
scheme referred as ‘Digital Adaptive Equalization.’
The Digital Equalizer removes ISI (inter symbol interference) from the receive data stream by continuously adapting to provide a filter with the inverse frequency response
of the channel. Equalization is combined with an adaptive
gain control stage. This enables the receive 'eye pattern' to
be opened sufficiently to allow very reliable data recovery.
The curves given in Figure 9 illustrate attenuation at certain
frequencies for given cable lengths. This is derived from
the worst case frequency vs. attenuation figures as specified in the EIA/TIA Bulletin TSB-36. These curves indicate
the significant variations in signal attenuation that must be
compensated for by the receive adaptive equalization circuit.
Figure 9. EIA/TIA Attenuation vs. Frequency for 0, 50,
100, 130 & 150 meters of CAT 5 cable
30
www.national.com
DP83849ID
4.2.2.1 Digital Adaptive Equalization and Gain Control
DP83849ID
4.2.2.2 Base Line Wander Compensation
Figure 10. 100BASE-TX BLW Event
The DP83849ID is completely ANSI TP-PMD compliant
and includes Base Line Wander (BLW) compensation. The
BLW compensation block can successfully recover the TPPMD defined “killer” pattern.
FDDI TP-PMD Standard as well as the IEEE 802.3
100BASE-TX Standard for both voltage thresholds and timing parameters.
Note that the reception of normal 10BASE-T link pulses
BLW can generally be defined as the change in the aver- and fast link pulses per IEEE 802.3u Auto-Negotiation by
age DC content, relatively short period over time, of an AC the 100BASE-TX receiver do not cause the DP83849ID to
coupled digital transmission over a given transmission assert signal detect.
medium. (i.e., copper wire).
BLW results from the interaction between the low frequency components of a transmitted bit stream and the frequency response of the AC coupling component(s) within
the transmission system. If the low frequency content of
the digital bit stream goes below the low frequency pole of
the AC coupling transformers then the droop characteristics of the transformers will dominate resulting in potentially
serious BLW.
4.2.4 MLT-3 to NRZI Decoder
The DP83849ID decodes the MLT-3 information from the
Digital Adaptive Equalizer block to binary NRZI data.
4.2.5 NRZI to NRZ
The digital oscilloscope plot provided in Figure 10 illus- In a typical application, the NRZI to NRZ decoder is
trates the severity of the BLW event that can theoretically required in order to present NRZ formatted data to the
be generated during 100BASE-TX packet transmission. descrambler.
This event consists of approximately 800 mV of DC offset
for a period of 120 µs. Left uncompensated, events such as
this can cause packet loss.
4.2.6 Serial to Parallel
The 100BASE-TX receiver includes a Serial to Parallel
converter which supplies 5-bit wide data symbols to the
PCS Rx state machine.
4.2.3 Signal Detect
The signal detect function of the DP83849ID is incorporated to meet the specifications mandated by the ANSI
31
www.national.com
A serial descrambler is used to de-scramble the received
NRZ data. The descrambler has to generate an identical
data scrambling sequence (N) in order to recover the original unscrambled data (UD) from the scrambled data (SD)
as represented in the equations:
SD = ( UD ⊕ N )
UD = ( SD ⊕ N )
4.2.10 100BASE-TX Link Integrity Monitor
The 100 Base TX Link monitor ensures that a valid and stable link is established before enabling both the Transmit
and Receive PCS layer.
Signal detect must be valid for 395us to allow the link monitor to enter the 'Link Up' state, and enable the transmit and
receive functions.
Synchronization of the descrambler to the original scrambling sequence (N) is achieved based on the knowledge
that the incoming scrambled data stream consists of
scrambled IDLE data. After the descrambler has recognized 12 consecutive IDLE code-groups, where an
unscrambled IDLE code-group in 5B NRZ is equal to five
consecutive ones (11111), it will synchronize to the receive
data stream and generate unscrambled data in the form of
unaligned 5B code-groups.
In order to maintain synchronization, the descrambler must
continuously monitor the validity of the unscrambled data
that it generates. To ensure this, a line state monitor and a
hold timer are used to constantly monitor the synchronization status. Upon synchronization of the descrambler the
hold timer starts a 722 µs countdown. Upon detection of
sufficient IDLE code-groups (58 bit times) within the 722 µs
period, the hold timer will reset and begin a new countdown. This monitoring operation will continue indefinitely
given a properly operating network connection with good
signal integrity. If the line state monitor does not recognize
sufficient unscrambled IDLE code-groups within the 722 µs
period, the entire descrambler will be forced out of the current state of synchronization and reset in order to reacquire synchronization.
4.2.11 Bad SSD Detection
A Bad Start of Stream Delimiter (Bad SSD) is any transition
from consecutive idle code-groups to non-idle code-groups
which is not prefixed by the code-group pair /J/K.
If this condition is detected, the DP83849ID will assert
RX_ER and present RXD[3:0] = 1110 to the MII for the
cycles that correspond to received 5B code-groups until at
least two IDLE code groups are detected. In addition, the
False Carrier Sense Counter register (FCSCR) will be
incremented by one.
Once at least two IDLE code groups are detected, RX_ER
and CRS become de-asserted.
4.3 100BASE-FX Operation
The DP83849ID provides IEEE 802.3 compliant 100BASEFX operation. Configuration of FX mode is via strap option,
or through the register interface.
4.3.1 100BASE-FX Transmit
4.2.8 Code-group Alignment
The code-group alignment module operates on unaligned
5-bit data from the descrambler (or, if the descrambler is
bypassed, directly from the NRZI/NRZ decoder) and converts it into 5B code-group data (5 bits). Code-group alignment occurs after the J/K code-group pair is detected.
Once the J/K code-group pair (11000 10001) is detected,
subsequent data is aligned on a fixed boundary.
In 100BASE-FX mode, the device Transmit Pins connect to
an industry standard Fiber Transceiver with PECL signalling through a capacitively coupled circuit.
In FX mode, the device bypasses the Scrambler and the
MLT3 encoder. This allows for the transmission of serialized 5B4B encoded NRZI data at 125MHz.
The only added functionality from 100BASE-TX is the support for Far-End Fault data generation.
4.2.9 4B/5B Decoder
4.3.2 100BASE-FX Receive
The code-group decoder functions as a look up table that
translates incoming 5B code-groups into 4B nibbles. The
code-group decoder first detects the J/K code-group pair
preceded by IDLE code-groups and replaces the J/K with
MAC preamble. Specifically, the J/K 10-bit code-group pair
is replaced by the nibble pair (0101 0101). All subsequent
5B code-groups are converted to the corresponding 4B
nibbles for the duration of the entire packet. This conversion ceases upon the detection of the T/R code-group pair
denoting the End of Stream Delimiter (ESD) or with the
reception of a minimum of two IDLE code-groups.
In 100BASE-FX mode, the device Receive pins connect to
an industry standard Fiber Transceiver with PECL signalling through a capacitively coupled circuit.
In FX mode, the device bypasses MLT3 Decoder and the
Descrambler. This allows for the reception of serialized
5B4B encoded NRZI data at 125MHz.
The only added functionality for 100BASE-FX from
100BASE-TX is the support of Far-End Fault detection.
32
www.national.com
DP83849ID
4.2.7 Descrambler
Full Duplex Mode
Since 100BASE-FX does not support Auto-Negotiation, a In Full Duplex mode the DP83849ID is capable of simultaFar-End Fault facility is included which allows for detection neously transmitting and receiving without asserting the
collision signal. The DP83849ID's 10 Mb/s ENDEC is
of link failures.
When no signal is being received as determined by the designed to encode and decode simultaneously.
Signal Detect function, the device sends a Far-End Fault
indication to the far-end peer. The Far-End Fault indication
is comprised of 3 or more repeating cycles, each consisting
of 84 one’s followed by 1 zero. The pattern is such that it
will not satisfy the 100BASE-X carrier sense mechanism,
but is easily detected as the Fault indication. The pattern
will be transparent to devices that do not support Far-End
Fault.
4.4.2 Smart Squelch
The smart squelch is responsible for determining when
valid data is present on the differential receive inputs. The
DP83849ID implements an intelligent receive squelch to
ensure that impulse noise on the receive inputs will not be
mistaken for a valid signal. Smart squelch operation is
The Far-End Fault detection process continuously monitors independent of the 10BASE-T operational mode.
the receive data stream for the Far-End Fault indication.
When detected, the Link Monitor is forced to deassert Link The squelch circuitry employs a combination of amplitude
and timing measurements (as specified in the IEEE 802.3
status. This causes the device to transmit IDLE’s on its
10BSE-T standard) to determine the validity of data on the
transmit path.
twisted pair inputs (refer to Figure 11).
The signal at the start of a packet is checked by the smart
squelch and any pulses not exceeding the squelch level
4.4 10BASE-T TRANSCEIVER MODULE
(either positive or negative, depending upon polarity) will
The 10BASE-T Transceiver Module is IEEE 802.3 compli- be rejected. Once this first squelch level is overcome corant. It includes the receiver, transmitter, collision, heart- rectly, the opposite squelch level must then be exceeded
beat, loopback, jabber, and link integrity functions, as within 150 ns. Finally the signal must again exceed the
defined in the standard. An external filter is not required on original squelch level within 150 ns to ensure that the input
the 10BASE-T interface since this is integrated inside the waveform will not be rejected. This checking procedure
DP83849ID. This section focuses on the general 10BASE- results in the loss of typically three preamble bits at the
beginning of each packet.
T system level operation.
Only after all these conditions have been satisfied will a
control signal be generated to indicate to the remainder of
the circuitry that valid data is present. At this time, the
smart squelch circuitry is reset.
4.4.1 Operational Modes
The DP83849ID has two basic 10BASE-T operational
Valid data is considered to be present until the squelch
modes:
level has not been generated for a time longer than 150 ns,
— Half Duplex mode
indicating the End of Packet. Once good data has been
— Full Duplex mode
detected, the squelch levels are reduced to minimize the
effect of noise causing premature End of Packet detection.
Half Duplex Mode
In Half Duplex mode the DP83849ID functions as a standard IEEE 802.3 10BASE-T transceiver supporting the
CSMA/CD protocol.
<150 ns
>150 ns
<150 ns
VSQ+
VSQ+(reduced)
VSQ-(reduced)
VSQend of packet
start of packet
Figure 11. 10BASE-T Twisted Pair Smart Squelch Operation
33
www.national.com
DP83849ID
4.3.3 Far-End Fault
Once disabled by the Jabber function, the transmitter stays
disabled for the entire time that the ENDEC module's interWhen in Half Duplex, a 10BASE-T collision is detected
nal transmit enable is asserted. This signal has to be dewhen the receive and transmit channels are active simultaasserted for approximately 500 ms (the “unjab” time)
neously. Collisions are reported by the COL signal on the before the Jabber function re-enables the transmit outputs.
MII. Collisions are also reported when a jabber condition is
The Jabber function is only relevant in 10BASE-T mode.
detected.
The COL signal remains set for the duration of the collision.
If the PHY is receiving when a collision is detected it is
reported immediately (through the COL pin).
When heartbeat is enabled, approximately 1 µs after the
transmission of each packet, a Signal Quality Error (SQE)
signal of approximately 10-bit times is generated to indicate successful transmission. SQE is reported as a pulse
on the COL signal of the MII.
The SQE test is inhibited when the PHY is set in full duplex
mode. SQE can also be inhibited by setting the
HEARTBEAT_DIS bit in the 10BTSCR register.
4.4.7 Automatic Link Polarity Detection and Correction
The DP83849ID's 10BASE-T transceiver module incorporates an automatic link polarity detection circuit. When
three consecutive inverted link pulses are received, bad
polarity is reported.
A polarity reversal can be caused by a wiring error at either
end of the cable, usually at the Main Distribution Frame
(MDF) or patch panel in the wiring closet.
4.4.4 Carrier Sense
The bad polarity condition is latched in the 10BTSCR register. The DP83849ID's 10BASE-T transceiver module corrects for this error internally and will continue to decode
received data correctly. This eliminates the need to correct
the wiring error immediately.
Carrier Sense (CRS) may be asserted due to receive activity once valid data is detected via the squelch function.
4.4.8 Transmit and Receive Filtering
For 10 Mb/s Half Duplex operation, CRS is asserted during
either packet transmission or reception.
For 10 Mb/s Full Duplex operation, CRS is asserted only
during receive activity.
CRS is deasserted following an end of packet.
4.4.5 Normal Link Pulse Detection/Generation
External 10BASE-T filters are not required when using the
DP83849ID, as the required signal conditioning is integrated into the device.
Only isolation transformers and impedance matching resistors are required for the 10BASE-T transmit and receive
interface. The internal transmit filtering ensures that all the
harmonics in the transmit signal are attenuated by at least
30 dB.
The link pulse generator produces pulses as defined in the
IEEE 802.3 10BASE-T standard. Each link pulse is nominally 100 ns in duration and transmitted every 16 ms in the 4.4.9 Transmitter
absence of transmit data.
The encoder begins operation when the Transmit Enable
Link pulses are used to check the integrity of the connec- input (TX_EN) goes high and converts NRZ data to pretion with the remote end. If valid link pulses are not emphasized Manchester data for the transceiver. For the
received, the link detector disables the 10BASE-T twisted duration of TX_EN, the serialized Transmit Data (TXD) is
encoded for the transmit-driver pair (PMD Output Pair).
pair transmitter, receiver and collision detection functions.
TXD must be valid on the rising edge of Transmit Clock
When
the
link
integrity
function
is
disabled (TX_CLK). Transmission ends when TX_EN deasserts.
(FORCE_LINK_10 of the 10BTSCR register), a good link is The last transition is always positive; it occurs at the center
forced and the 10BASE-T transceiver will operate regard- of the bit cell if the last bit is a one, or at the end of the bit
less of the presence of link pulses.
cell if the last bit is a zero.
4.4.6 Jabber Function
4.4.10 Receiver
The jabber function monitors the DP83849ID's output and
disables the transmitter if it attempts to transmit a packet of
longer than legal size. A jabber timer monitors the transmitter and disables the transmission if the transmitter is active
for approximately 85 ms.
The decoder detects the end of a frame when no additional
mid-bit transitions are detected. Within one and a half bit
times after the last bit, carrier sense is de-asserted.
Receive clock stays active for five more bit times after CRS
goes low, to guarantee the receive timings of the controller.
34
www.national.com
DP83849ID
4.4.3 Collision Detection and SQE
5.1 TPI Network Circuit
Figure 12 shows the recommended circuit for a 10/100
Mb/s twisted pair interface.
Below is a partial list of recommended transformers. It is
important that the user realize that variations with PCB and
component characteristics requires that the application be
tested to ensure that the circuit meets the requirements of
the intended application.
Pulse H1102
Pulse H2019
Belfuse S558-5999-U7
Halo TG110-S050N2RL
Vdd
TPRDM
Vdd
COMMON MODE CHOKES
MAY BE REQUIRED.
49.9Ω
0.1µF
1:1
49.9Ω
TDRDP
RD-
0.1µF*
RD+
TD-
TPTDM
TD+
0.1µF*
Vdd
49.9Ω
RJ45
1:1
0.1µF
T1
NOTE: CENTER TAP IS PULLED TO VDD
49.9Ω
*PLACE CAPACITORS CLOSE TO THE
TRANSFORMER CENTER TAPS
TPTDP
All values are typical and are +/- 1%
PLACE RESISTORS AND
CAPACITORS CLOSE TO
THE DEVICE.
Figure 12. 10/100 Mb/s Twisted Pair Interface
35
www.national.com
DP83849ID
5.0 Design Guidelines
DP83849ID
5.2 Fiber Network Circuit
Figure 13 shows the recommended circuit for a 100 Mb/s
fiber pair interface.
Vdd
50Ω
50Ω
130Ω
130Ω
130Ω
130Ω
130Ω
80Ω
80Ω
80Ω
0.1 uF
FXTDP
FXTDM
Fiber Transceiver
0.1 uF
FXSD
FXRDP
FXRDM
80 Ω
80Ω
PLACE RESISTORS AND
CAPACITORS CLOSE TO
THE DEVICE.
PLACE RESISTORS
CLOSE TO THE FIBER
TRANSCEIVER.
All values are typical and are +/- 1%
Figure 13. 100 Mb/s Fiber Pair Interface
36
www.national.com
cal connection for a crystal resonator circuit. The load
capacitor values will vary with the crystal vendors; check
Typically, ESD precautions are predominantly in effect with the vendor for the recommended loads.
when handling the devices or board before being installed
in a system. In those cases, strict handling procedures The oscillator circuit is designed to drive a parallel resoneed be implemented during the manufacturing process to nance AT cut crystal with a minimum drive level of 100µW
greatly reduce the occurrences of catastrophic ESD and a maximum of 500µW. If a crystal is specified for a
events. After the system is assembled, internal compo- lower drive level, a current limiting resistor should be
placed in series between X2 and the crystal.
nents are less sensitive from ESD events.
The network interface pins are more susceptible to ESD As a starting point for evaluating an oscillator circuit, if the
requirements for the crystal are not known, CL1 and CL2
events.
should be set at 33 pF, and R1 should be set at 0Ω.
Specification for 25 MHz crystal are listed in Table 16.
5.4 Clock In (X1) Requirements
The DP83849ID supports an external CMOS level oscillator source or a crystal resonator device.
X2
X1
Oscillator
If an external clock source is used, X1 should be tied to the
clock source and X2 should be left floating.
R1
Specifications for CMOS oscillators: 25 MHz in MII Mode
and 50 MHz in RMII Mode are listed in Table 14 and Table
15.
CL1
CL2
Note: Maximum Reference Clock Jitter should not exceed
1ns peak-to-peak or 78ps rms from 50kHz to 1MHz.
Figure 14. Crystal Oscillator Circuit
Crystal
A 25 MHz, parallel, 20 pF load crystal resonator should be
used if a crystal source is desired. Figure 14 shows a typiTable 14. 25 MHz Oscillator Specification
Parameter
Min
Frequency
Typ
Max
25
Units
Condition
MHz
Frequency
+50
ppm
Operational Temperature
+50
ppm
1 year aging
6
nsec
20% - 80%
Tolerance
Frequency
Stability
Rise / Fall Time
Jitter (short term)
50
Jitter (long term)
Symmetry
1
40%
psec
Cycle-to-cycle
nsec
Accumulative over 10µs
60%
Duty Cycle
Table 15. 50 MHz Oscillator Specification
Parameter
Min
Frequency
Typ
Max
50
Units
Condition
MHz
Frequency
+50
ppm
Operational Temperature
+50
ppm
Operational Temperature
6
nsec
20% - 80%
psec
Cycle-to-cycle
nsec
Accumulative over 10µs
Tolerance
Frequency
Stability
Rise / Fall Time
Jitter (short term)
50
Jitter (long term)
Symmetry
1
40%
60%
37
Duty Cycle
www.national.com
DP83849ID
5.3 ESD Protection
Parameter
Min
Typ
Frequency
Max
Units
25
Condition
MHz
Frequency
+50
ppm
Operational Temperature
+50
ppm
1 year aging
40
pF
Tolerance
Frequency
Stability
Load Capacitance
25
5.5 Power Feedback Circuit
To ensure correct operation for the DP83849ID, parallel
caps with values of 10 µF and 0.1 µF should be placed
close to pin 31 (PFBOUT) of the device. Pin 7 (PFBIN1),
pin 28 (PFBIN2), pin 34 (PFBIN3) and pin 54 (PFBIN4)
must be connected to pin 31 (PFBOUT), each pin requires
a small capacitor (.1 µF). See Figure 15 below for proper
connections.
Pin 31 (PFBOUT)
10 µF +
.1 µF
Pin 7 (PFBIN1)
.1 µF
Pin 28 (PFBIN2)
-
.1 µF
Pin 34 (PFBIN3)
Pin 54 (PFBIN4)
.1 µF
.1 µF
Figure 15. Power Feeback Connection
bit 11 (Power Down) in the Basic Mode Control Register,
BMCR (00h). An external control signal can be used to
The Power Down and Interrupt functions are multiplexed drive the pin low, overcoming the weak internal pull-up
on pin 18 and pin 44 of the device. By default, this pin func- resistor. Alternatively, the device can be configured to initions as a power down input and the interrupt function is tialize into a Power Down state by use of an external pulldisabled. Setting bit 0 (INT_OE) of MICR (11h) will config- down resistor on the PWRDOWN_INT pin. Since the
ure the pin as an active low interrupt output. Ports A and B device will still respond to management register accesses,
can be powered down individually, using the separate setting the INT_OE bit in the MICR register will disable the
PWRDOWN_INT_A and PWRDOWN_INT_B pins.
PWRDOWN_INT input, allowing the device to exit the
Power Down state.
5.6 Power Down/Interrupt
5.6.1 Power Down Control Mode
The PWRDOWN_INT pins can be asserted low to put the
device in a Power Down mode. This is equivalent to setting
38
www.national.com
DP83849ID
Table 16. 25 MHz Crystal Specification
5.8.1 Linked Cable Status
Since each port has a separate interrupt pin, the interrupts
can be connected individually or may be combined in a
wired-OR fashion. If the interrupts share a single connection, each port status should be checked following an interrupt.
In an active connection with a valid link status, the following
diagnostic capabilities are available:
— Polarity reversal
— Cable swap (MDI vs MDIX) detection
The interrupt function is controlled via register access. All — 100Mb Cable Length Estimation
interrupt sources are disabled by default. Setting bit 1 — Frequency offset relative to link partner
(INTEN) of MICR (11h) will enable interrupts to be output, — Cable Signal Quality Estimation
dependent on the interrupt mask set in the lower byte of
the MISR (12h). The PWRDOWN_INT pin is asynchronously asserted low when an interrupt condition occurs.
The source of the interrupt can be determined by reading 5.8.1.1 Polarity Reversal
the upper byte of the MISR. One or more bits in the MISR The DP83849ID detects polarity reversal by detecting negwill be set, denoting all currently pending interrupts. Read- ative link pulses. The Polarity indication is available in bit
ing of the MISR clears ALL pending interrupts.
12 of the PHYSTS (10h) or bit 4 of the 10BTSCR (1Ah).
Example: To generate an interrupt on a change of link sta- Inverted polarity indicates the positive and negative contus or on a change of energy detect power state, the steps ductors in the receive pair are swapped. Since polarity is
corrected by the receiver, this does not necessarily indicate
would be:
a functional problem in the cable.
— Write 0003h to MICR to set INTEN and INT_OE
Since the polarity indication is dependent on link pulses
— Write 0060h to MISR to set ED_INT_EN and
from the link partner, polarity indication is only valid in
LINK_INT_EN
10Mb modes of operation, or in 100Mb Auto-Negotiated
— Monitor PWRDOWN_INT pin
mode. Polarity indication is not available in 100Mb forced
mode of operation or in a parallel detected 100Mb mode.
When PWRDOWN_INT pin asserts low, the user would
read the MISR register to see if the ED_INT or LINK_INT
bits are set, i.e. which source caused the interrupt. After
reading the MISR, the interrupt bits should clear and the
PWRDOWN_INT pin will deassert.
5.7 Energy Detect Mode
When Energy Detect is enabled and there is no activity on
the cable, the DP83849ID will remain in a low power mode
while monitoring the transmission line. Activity on the line
will cause the DP83849ID to go through a normal power up
sequence. Regardless of cable activity, the DP83849ID will
occasionally wake up the transmitter to put ED pulses on
the line, but will otherwise draw as little power as possible.
Energy detect functionality is controlled via register Energy
Detect Control (EDCR), address 1Dh.
5.8 Link Diagnostic Capabilities
5.8.1.2 Cable Swap Indication
As part of Auto-Negotiation, the DP83849ID has the ability
(using Auto-MDIX) to automatically detect a cable with
swapped MDI pairs and select the appropriate pairs for
transmitting and receiving data. Normal operation is
termed MDI, while crossed operation is MDIX. The MDIX
status can be read from bit 14 of the PHYSTS (10h).
5.8.1.3 100MB Cable Length Estimation
The DP83849ID provides a method of estimating cable
length based on electrical characteristics of the 100Mb
Link. This essentially provides an effective cable length
rather than a measurement of the physical cable length.
The cable length estimation is only available in 100Mb
mode of operation with a valid Link status. The cable
length estimation is available at the Link Diagnostics Registers - Page 2, register 100Mb Length Detect
(LEN100_DET), address 14h.
The DP83849ID contains several system diagnostic capabilities for evaluating link quality and detecting potential
cabling faults in Twisted Pair cabling. Software configuration is available through the Link Diagnostics Registers - 5.8.1.4 Frequency Offset Relative to Link Partner
Page 2 which can be selected via Page Select Register As part of the 100Mb clock recovery process, the DSP
(PAGESEL), address 13h. These capabilities include:
implementation provides a frequency control parameter.
This value may be used to indicate the frequency offset of
— Linked Cable Status
the device relative to the link partner. This operation is only
— Link Quality Monitor
available in 100Mb operation with a valid link status. The
— TDR (Time Domain Reflectometry) Cable Diagnostics
frequency offset can be determined using the register
100Mb Frequency Offset Indication (FREQ100), address
15h, of the Link Diagnostics Registers - Page 2.
Two different versions of the Frequency Offset may be
monitored through bits [7:0] of register FREQ100 (15h).
The first is the long-term Frequency Offset. The second is
the current Frequency Control value, which includes shortterm phase adjustments and can provide information on
the amount of jitter in the system.
39
www.national.com
DP83849ID
5.6.2 Interrupt Mechanisms
function. In addition, it provides warning status from both
high and low thresholds for each of the monitored parameThe cable signal quality estimator keeps a simple tracking
ters. Note that individual low or high parameter threshold
of results of the DSP and can be used to generate an
comparisons can be disabled by setting to the minimum or
approximate Signal-to-Noise Ratio for the 100Mb receiver. maximum values.
This information is available to software through the Link
Diagnostics Registers - Page 2: Variance Control To allow the Link Quality Monitor to interrupt the system,
(VAR_CTRL), address 1Ah and Data (VAR_DATA), the Interrupt must be enabled through the interrupt control
registers, MICR (11h) and MISR (12h).
address 1Bh.
The variance computation times (VAR_TIMER) can be
chosen from the set of {2, 4, 6, 8} ms. The 32-bit variance
sum can be read by two consecutive reads of the
VAR_DATA register. This sum can be used to compute an
SNR estimate by software using the following equation:
SNR = 10log10((37748736 * VAR_TIMER) / Variance).
5.8.2 Link Quality Monitor
The Link Quality Monitor allows a method to generate an
alarm when the DSP adaption strays from a programmable
window. This could occur due to changes in the cable
which could indicate a potential problem. Software can
program thresholds for the following DSP parameters to be
used to interrupt the system:
—
—
—
—
—
Digital Equalizer C1 Coefficient (DEQ C1)
Digital Adaptive Gain Control (DAGC)
Digital Base-Line Wander Control (DBLW)
Recovered Clock Long-Term Frequency Offset (FREQ)
Recovered Clock Frequency Control (FC)
5.8.2.2 Checking Current Parameter Values
Prior to setting Threshold values, it is recommended that
software check current adapted values. The thresholds
may then be set relative to the adapted values. The current
adapted values can be read using the LQDR register by
setting the Sample_Param bit [13] of LQDR, address
(1Eh).
For example, to read the DBLW current value:
1. Write 2400h to LQDR (1Eh) to set the Sample_Param
bit and set the LQ_PARAM_SEL[2:0] to 010.
2. Read LQDR (1Eh). Current DBLW value is returned
in the low 8 bits.
5.8.2.3 Threshold Control
The LQDR (1Eh) register also provides a method of programming high and low thresholds for each of the four
parameters that can be monitored. The register implements an indirect read/write mechanism.
Software is expected to read initial adapted values and
then program the thresholds based on an expected valid
range. This mechanism takes advantage of the fact that
the DSP adaption should remain in a relatively small range
once a valid link has been established.
Writes are accomplished by writing data, address, and a
write strobe to the register. Reads are accomplished by
writing the address to the register, and reading back the
value of the selected threshold. Setting thresholds to the
maximum or minimum values will disable the threshold
comparison since values have to exceed the threshold to
generate a warning condition.
5.8.2.1 Link Quality Monitor Control and Status
Warnings are not generated if the parameter is equal to the
threshold. By default, all thresholds are disabled by setting
to the min or max values. The following table shows the
four parameters and range of values:
Control of the Link Quality Monitor is done through the Link
Quality Monitor Register (LQMR), address 1Dh and the
Link Quality Data Register (LQDR), address 1Bh of the
Link Diagnostics Registers - Page 2. The LQMR register
includes a global enable to enable the Link Quality Monitor
Table 17. Link Quality Monitor Parameter Ranges
Parameter
Minimum Value
Maximum Value
Min (2-s comp)
Max (2-s comp)
-128
+127
0x80
0x7F
DAGC
0
+255
0x00
0xFF
DBLW
-128
+127
0x80
0x7F
Freq Offset
-128
+127
0x80
0x7F
Freq Control
-128
+127
0x80
0x7F
DEQ C1
40
www.national.com
DP83849ID
5.8.1.5 Cable Signal Quality Estimation
The DP83849ID implements a Time Domain Reflectometry
(TDR) method of cable length measurement and evaluation which can be used to evaluate a connected twisted
pair cable. The TDR implementation involves sending a
pulse out on either the Transmit or Receive conductor pair
and observing the results on either pair. By observing the
types and strength of reflections on each pair, software can
determine the following:
—
—
—
—
—
Cable short
Cable open
Distance to fault
Identify which pair has a fault
Pair skew
This is especially useful for eliminating the transmitted
pulse, but also may be used to look for multiple reflections.
5.8.3.3 TDR Control Interface
The TDR Control interface is implemented in the Link Diagnostics Registers - Page 2 through TDR Control
(TDR_CTRL), address 16h and TDR Window (TDR_WIN),
address 17h. The following basic controls are:
— TDR Enable: Enable bit 15 of TDR_CTRL (16h) to allow
the TDR function. This bypasses normal operation and
gives control of the CD10 and CD100 block to the TDR
function.
— TDR Send Pulse: Enable bit 11 of TDR_CTRL (16h) to
send the TDR pulse and starts the TDR Monitor.
The following Transmit mode controls are available:
The TDR cable diagnostics works best in certain conditions. For example, an unterminated cable provides a
good reflection for measuring cable length, while a cable
with an ideal termination to an unpowered partner may provide no reflection at all.
— Transmit Mode: Enables use of 10Mb Link pulses from
the 10Mb Common Driver or data pulses from the 100Mb
Common Driver by enabling TDR 100Mb, bit 14 of
TDR_CRTL (16h).
— Transmit Pulse Width: Bits [10:8] of TDR_CTRL (16h)
allows sending of 0 to 7 clock width pulses. Actual pulses are dependent on the transmit mode. If Pulse Width
5.8.3.1 TDR Pulse Generator
is set to 0, then no pulse will be sent.
The TDR implementation can send two types of TDR — Transmit Channel Select: The transmitter can send
pulses. The first option is to send 50ns or 100ns link
pulses down either the transmit pair or the receive pair
pulses from the 10Mb Common Driver. The second option
by enabling bit 13 of TDR_CTRL (16h). Default value is
is to send pulses from the 100Mb Common Driver in 8ns
to select the transmit pair.
increments up to 56ns in width. The 100Mb pulses will
alternate between positive and negative pulses. The
shorter pulses provide better ability to measure short cable The following Receive mode controls are available:
lengths, especially since they will limit overlap between the — Min/Max Mode Select: Bit 7 of TDR_CTRL (16h) contransmitted pulse and a reflected pulse. The longer pulses
trols the TDR Monitor operation. In default mode, the
may provide better measurements of long cable lengths.
monitor will detect maximum (positive) values. In Min
mode, the monitor will detect minimum (negative) valIn addition, if the pulse width is programmed to 0, no pulse
ues.
will be sent, but monitor circuit will still be activated. This
allows sampling of background data to provide a baseline — Receive Channel Select: The receiver can monitor eifor analysis.
ther the transmit pair or the receive pair by enabling bit
12 of TDR_CTRL (16h). Default value is to select the
transmit pair.
5.8.3.2 TDR Pulse Monitor
— Receive Window: The receiver can monitor receive
data within a programmable window using the TDR WinThe TDR function monitors data from the Analog to Digital
dow Register (TDR_WIN), address 17h. The window is
Converter (ADC) to detect both peak values and values
controlled by two register values: TDR Start Window, bits
above a programmable threshold. It can be programmed
[15:8] of TDR_WIN (17h) and TDR Stop Window, bits
to detect maximum or minimum values. In addition, it
[7:0] of TDR_WIN (17h). The TDR Start Window indirecords the time, in 8ns intervals, at which the peak or
cates the first clock to start sampling. The TDR Stop
threshold value first occurs.
Window indicates the last clock to sample. By default,
The TDR monitor implements a timer that starts when the
the full window is enabled, with Start set to 0 and Stop
pulse is transmitted. A window may be enabled to qualify
set to 255. The window range is in 8ns clock increments,
incoming data to look for response only in a desired range.
so the maximum window size is 2048ns.
41
www.national.com
DP83849ID
5.8.3 TDR Cable Diagnostics
Software utilizing the TDR function should implement an
algorithm to send TDR pulses and evaluate results. MultiThe TDR function monitors data from the Analog to Digital
ple runs should be used to best qualify any received pulses
Converter (ADC) to detect both peak values and values
as multiple reflections could exist. In addition, when moniabove a programmable threshold. It can be programmed toring the transmitting pair, the window feature should be
to detect maximum or minimum values. In addition, it
used to disqualify the transmitted pulse. Multiple runs may
records the time, in 8ns intervals, at which the peak or
also be used to average the values providing more accuthreshold value first occurs. The results of a TDR peak and rate results.
threshold measurement are available in the TDR Peak
Measurement Register (TDR_PEAK), address 18h and Actual distance measurements are dependent on the
TDR Threshold Measurement Register (TDR_THR), velocity of propagation of the cable. The delay value is typaddress 19h. The threshold measurement may be a more ically on the order of 4.6 to 4.9 ns/m.
accurate method of measuring the length for longer cables
to provide a better indication of the start of the received
pulse, rather than the peak value.
42
www.national.com
DP83849ID
5.8.3.4 TDR Results
The DP83849ID includes an internal power-on reset (POR)
function and does not need to be explicitly reset for normal
operation after power up. If required during normal operation, the device can be reset by a hardware or software
reset.
(BMCR). The period from the point in time when the reset
bit is set to the point in time when software reset has concluded is approximately 1 µs.
The software reset will reset the device such that all registers will be reset to default values and the hardware configuration values will be maintained. Software driver code
must wait 3 µs following a software reset before allowing
further serial MII operations with the DP83849ID.
6.1 Hardware Reset
A hardware reset is accomplished by applying a low pulse
(TTL level), with a duration of at least 1 µs, to the
RESET_N pin. This will reset the device such that all registers will be reinitialized to default values and the hardware
configuration values will be re-latched into the device (similar to the power-up/reset operation).
6.3 Soft Reset
A partial software reset can be initiated by setting the Soft
Reset bit (bit 9) in the PHYCR2 Register. Setting this bit will
reset all transmit and receive operations, but will not reset
the register space. All register configurations will be preserved. Register space will remain available following a
Soft Reset.
6.2 Full Software Reset
A full-chip software reset is accomplished by setting the
reset bit (bit 15) of the Basic Mode Control Register
43
www.national.com
DP83849ID
6.0 Reset Operation
DP83849ID
7.0 Register Block
Table 18. Register Map
Offset
Access
Tag
Description
Hex
Decimal
00h
0
RW
BMCR
Basic Mode Control Register
01h
1
RO
BMSR
Basic Mode Status Register
02h
2
RO
PHYIDR1
PHY Identifier Register #1
03h
3
RO
PHYIDR2
PHY Identifier Register #2
04h
4
RW
ANAR
Auto-Negotiation Advertisement Register
05h
5
RW
ANLPAR
Auto-Negotiation Link Partner Ability Register (Base Page)
05h
5
RW
ANLPARNP
Auto-Negotiation Link Partner Ability Register (Next Page)
06h
6
RW
ANER
Auto-Negotiation Expansion Register
RW
ANNPTR
Auto-Negotiation Next Page TX
RESERVED
RESERVED
07h
7
08h-Fh
8-15
10h
16
RO
PHYSTS
PHY Status Register
11h
17
RW
MICR
MII Interrupt Control Register
12h
18
RW
MISR
MII Interrupt Status Register
13h
19
RW
PAGESEL
Page Select Register
14h
20
RO
FCSCR
False Carrier Sense Counter Register
15h
21
RO
RECR
Receive Error Counter Register
16h
22
RW
PCSR
PCS Sub-Layer Configuration and Status Register
17h
23
RW
RBR
RMII and Bypass Register
18h
24
RW
LEDCR
LED Direct Control Register
Extended Registers - Page 0
19h
25
RW
PHYCR
PHY Control Register
1Ah
26
RW
10BTSCR
10Base-T Status/Control Register
1Bh
27
RW
CDCTRL1
CD Test Control Register and BIST Extensions Register
1Ch
28
RW
PHYCR2
Phy Control Register 2
RW
1Dh
29
EDCR
Energy Detect Control Register
1Eh-1Fh
30-31
RESERVED
RESERVED
14h-1Fh
20-31
RESERVED
14h
20
RO
LEN100_DET
100Mb Length Detect Register
15h
21
RW
FREQ100
100Mb Frequency Offset Indication Register
16h
22
RW
TDR_CTRL
TDR Control Register
17h
23
RW
TDR_WIN
TDR Window Register
18h
24
RO
TDR_PEAK
TDR Peak Measurement Register
Reserved Registers
RESERVED
Link Diagnostics Registers - Page 2
19h
25
RO
TDR_THR
TDR Threshold Measurement Register
1Ah
26
RW
VAR_CTRL
Variance Control Register
RO
VAR_DAT
Variance Data Register
RESERVED
RESERVED
1Bh
27
1Ch
28
1Dh
29
RW
LQMR
Link Quality Monitor Register
1Eh
30
RW
LQDR
Link Quality Data Register
1Fh
31
RESERVED
RESERVED
44
www.national.com
45
www.national.com
10h
11h
12h
13h
14h
15h
16h
MII Interrupt Control Register
MII Interrupt Status and Misc. Control Register
Page Select Register
False Carrier Sense Counter Register
Receive Error Counter Register
PCS Sub-Layer Configuration and Status
Register
06h
Auto-Negotiation Expansion Register
PHY Status Register
05h
Auto-Negotiation Link Partner Ability Register
Next Page
08-0fh
ANNext
LPARNP Page Ind
05h
Auto-Negotiation Link Partner Ability Register
(Base Page)
RESERVED
ANLPAR Next
Page Ind
04h
Auto-Negotiation Advertisement Register
07h
PHYIDR
2
03h
PHY Identifier Register 2
Auto-Negotiation Next Page TX Register
PHYIDR
1
02h
Reserved
Next
Page Ind
OUI LSB
Reserved
PCSR
RECR
FCSCR
Reserved
MISR
MICR
Reserved
Reserved
Reserved
Reserved
LQ_INT
Reserved
PHYSTS Reserved
Reserved
ANNPTR Next
Page Ind
ANER
ANAR
AutoNeg
Enable
100Base 100Base 10BaseT
-TX FDX -TX HDX
FDX
Speed
Selection
10BaseT
HDX
Power
Down
Reserved
Isolate
Bit 9
Reserved
Restart
AutoNeg
Bit 8
Reserved
Duplex
Mode
Bit 7
Reserved
Collision
Test
MF Preamble
Suppress
Reserved
Bit 6
AutoNeg
Complete
Reserved
Bit 5
Remote
Fault
Reserved
Bit 4
AutoNeg
Ability
Reserved
Bit 3
Link
Status
Reserved
Bit 2
Jabber
Detect
Reserved
Bit 1
Extended Capability
Reserved
Bit 0
Reserved
LINK_IN
T
Reserved
Rx Err
Latch
Reserved
Message
Page
Reserved
Message
Page
Remote
Fault
Remote
Fault
Reserved
SPD_IN
T
Reserved
Polarity
Status
Reserved
ACK2
Reserved
ACK2
Reserved
Reserved
Reserved
DUP_IN
T
Reserved
False
Carrier
Sense
Reserved
TOG_TX
Reserved
Toggle
ASM_DI
R
ASM_DI
R
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
FREE_C
LK
Reserved
Reserved
Reserved
CODE
Reserved
Code
TX_FD
TX_FD
Reserved
Reserved
DePage
scramReceive
bler Lock
Reserved
CODE
Reserved
Code
T4
T4
VNDR_
MDL
Reserved
Reserved
TQ_EN
Reserved
Reserved
Reserved
Reserved
Reserved
Remote
Fault
Reserved
CODE
Reserved
Code
10_FD
10_FD
VNDR_
MDL
Reserved
Jabber
Detect
Reserved
CODE
Reserved
Code
10
10
VNDR_
MDL
Reserved
Reserved
MDL_
REV
MDL_
REV
MDL_
REV
MDL_
REV
Reserved
SPED_I
NT_EN
Reserved
AutoNeg
Complete
Reserved
CODE
PDF
Code
Reserved
DUP_IN
T_EN
Reserved
Loopback Status
Reserved
CODE
LP_NP_
ABLE
Code
INTEN
Speed
Status
Reserved
CODE
PAGE_
RX
Code
INT_OE
Link
Status
Reserved
CODE
LP_AN_
ABLE
Code
Reserved
Page_Se Page_Se
l Bit
l Bit
ANC_IN FHF_INT RHF_IN
T_EN
_EN
T_EN
TINT
Duplex
Status
Reserved
CODE
NP_
ABLE
Code
Protocol Protocol Protocol Protocol Protocol
Selection Selection Selection Selection Selection
Protocol Protocol Protocol Protocol Protocol
Selection Selection Selection Selection Selection
VNDR_
MDL
RXERCNT
FX_EN
RXERCNT
FORCE_
100_OK
RXERCNT
Reserved
RXERCNT
FEFI_EN
RXERCNT
RXERCNT
RXERCNT
NRZI_ SCRAM_
DE
BYPASS BYPASS SCRAM_
BYPASS
RXERCNT
FCSCNT FCSCNT FCSCNT FCSCNT FCSCNT FCSCNT FCSCNT FCSCNT
Reserved
LQ_INT_ ED_INT_ LINK_IN
EN
EN
T_EN
Reserved
MII Interrupt
Reserved
CODE
Reserved
Code
TX
TX
VNDR_
MDL
SD_FOR
SD_
DESC_T
CE_PMA OPTION
IME
Reserved
Reserved
Reserved
ANC_IN FHF_INT RHF_IN
T
T
Reserved
Signal
Detect
Reserved
CODE
Reserved
Code
PAUSE
PAUSE
VNDR_
MDL
EXTENDED REGISTERS - PAGE 0
Reserved
ED_INT
Reserved
MDIX
mode
Reserved
Reserved
Reserved
ACK
ACK
Reserved
OUI LSB OUI LSB OUI LSB OUI LSB OUI LSB
OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB OUI MSB
100Base
-T4
PHY Identifier Register 1
BMSR
Loopback
Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10
Reset
01h
Tag
BMCR
Basic Mode Status Register
Addr
00h
Basic Mode Control Register
Register Name
Table 19. Register Table
46
www.national.com
1Ch
19h
TDR Threshold Register
RESERVED
18h
TDR Peak Register
1Bh
17h
TDR Window Register
Variance Data Register
16h
TDR Control Register
1Ah
15h
100Mb Frequency Offset Indication Register
Variance Control Register
14h
100Mb Length Detect Register
1Eh-1Fh
RESERVED
14h-1Fh
EDCR
1Dh
Energy Detect Control Register
RESERVED
PHYCR2 Reserved
1Ch
Phy Control Register 2
Reserved
Reserved
ED_EN
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RESERVED REGISTERS
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
TDR_10
0Mb
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
TX_CHA RX_CHA SEND_T TDR_WI
NNEL
NNEL
DR
DTH
Reserved
Reserved
TDR_WI
DTH
Reserved
Reserved
Bit 3
Bit 2
Bit 1
Bit 0
ELAST_
BUF
Reserved
Reserved
LP_DIS
Reserved
Reserved
FORCE_
LINK_10
Reserved
BIST_C
ONT_M
ODE
Reserved
Reserved
CDPattE
N_10
POLARITY
PHY
ADDR
Reserved
Reserved
Reserved
PHY
ADDR
Reserved
10Meg_
Patt_Ga
p
Reserved
PHY
ADDR
PHY
ADDR
Reserved
CDPattSel
Reserved
CDPattSel
HEARTB JABBER
EAT_DIS
_DIS
PHY
ADDR
CABLE_
LEN
Reserved
Reserved
CABLE_
LEN
Reserved
Reserved
Reserved
Reserved
CABLE_ CABLE_
LEN
LEN
Reserved
Reserved
CABLE_
LEN
Reserved
Reserved
CABLE_
LEN
Reserved
Reserved
Reserved
Reserved
CABLE_ CABLE_
LEN
LEN
Reserved
Reserved
TDR_WI
DTH
TDR_MI
N_MOD
E
Reserved
RX_THR RX_THR RX_THR RX_THR RX_THR RX_THR
ESHOLD ESHOLD ESHOLD ESHOLD ESHOLD ESHOLD
SEL_FC FREQ_O FREQ_O FREQ_O FREQ_O FREQ_O FREQ_O FREQ_O FREQ_O
FFSET
FFSET
FFSET
FFSET
FFSET
FFSET
FFSET
FFSET
Reserved
LINK DIAGNOSTICS REGISTERS - PAGE 2
Reserved
Reserved
Bit 4
RMII_RE RX_OVF RX_UNF ELAST_
V1_0
_STS
_STS
BUF
ED_ERR ED_DAT ED_ERR ED_ERR ED_ERR ED_ERR ED_DAT ED_DAT ED_DAT ED_DAT
_MET
A_MET _COUNT _COUNT _COUNT _COUNT A_COUN A_COUN A_COUN A_COUN
T
T
T
T
SOFT_R
ESET
SQUELC SQUELC SQUELC LOOPBA
H
H
H
CK_10_
DIS
ED_AUT ED_AUT ED_MAN ED_BUR ED_PW
O_UP
O_DOW
ST_DIS R_STAT
N
E
Reserved
Reserved
Bit 5
RMII_M
ODE
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
TDR_TH
R_MET
Reserved
TDRTHR_TI
ME
Reserved
TDRTHR_TI
ME
Reserved
TDRTHR_TI
ME
Reserved
TDRTHR_TI
ME
VAR_FR
EEZE
TDRTHR_TI
ME
VAR_TI
MER
TDRTHR_TI
ME
VAR_TI
MER
TDRTHR_TI
ME
VAR_TI
MER
TDRTHR_TI
ME
TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE TDR_PE
AK
AK
AK
AK
AK
AK
AK_TIM AK_TIM AK_TIM AK_TIM AK_TIM AK_TIM AK_TIM AK_TIM
E
E
E
E
E
E
E
E
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA VAR_DA
TA
TA
TAT
TA
TA
TA
TAT
TA
TA
TA
TAT
TA
TA
TA
TAT
TA
TA
VAR_CT VAR_RD
RL
Y
TDR_TH ReR
served
TDR_PE ReAK
served
TDR_WI TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST TDR_ST
N
ART
ART
ART
ART
ART
ART
ART
ART
OP
OP
OP
OP
OP
OP
OP
OP
TDR_CT TDR_EN
RL
ABLE
FREQ10 SAMPLE
0
_FREQ
LEN100_ ReDET
served
Reserved
Reserved
CDCTRL BIST_ER BIST_ER BIST_ER BIST_ER BIST_ER BIST_ER BIST_ER BIST_ER
1
ROR_C ROR_C ROR_C
ROR_C ROR_C ROR_C
ROR_C ROR_C
OUNT
OUNT OUNT
OUNT
OUNT OUNT
OUNT
OUNT
1Bh
CD Test Control and BIST Extensions Register
Reserved
Reserved
Bit 6
LEDACT BLINK_F BLINK_F DRV_SP DRV_LN DRV_AC SPDLED LNKLED ACTLED
_RX
REQ
REQ
DLED
KLED
TLED
Reserved
Bit 7
BIST_ BIST_ST BP_STR
LED_
LED_
STATUS
ART
ETCH CNFG[1] CNFG[0]
Reserved
10BT_S
ERIAL
Reserved
FORCE_ PAUSE_ PAUSE_ BIST_FE PSR_15
MDIX
RX
TX
Reserved
1Ah
Bit 8
PMD_LO
OP
10Base-T Status/Control Register
MDIX_E
N
Reserved
Reserved
Bit 9
PHYCR
Reserved
Reserved
19h
Reserved
Reserved
PHY Control Register
Reserved
Reserved
LEDCR
DIS_TX_
OPT
Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10
SIM_WR ReITE
served
18h
Tag
RBR
LED Direct Control Register
Addr
17h
RMII and Bypass Register
Register Name
Table 19. Register Table
47
www.national.com
LQDR
Reserved
1Eh
1Fh
RESERVED
Tag
LQMR
Link Quality Data Register
Addr
1Dh
Register Name
Link Quality Monitor Register
Reserved
Reserved
LQM_EN
ABLE
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Bit 9
FC_HI_
WARN
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
FC_LO_ FREQ_H FREQ_L DBLW_H DBLW_L DAGC_H DAGC_L
WARN I_WARN O_WAR I_WARN O_WAR I_WARN O_WAR
N
N
N
Bit 1
C1_HI_
WARN
Bit 0
C1_LO_
WARN
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
SAMPLE WRITE_ LQ_PAR LQ_PAR LQ_PAR LQ_THR LQ_THR LQ_THR LQ_THR LQ_THR LQ_THR LQ_THR LQ_THR LQ_THR
_PARAM LQ_THR AM_SEL AM_SEL AM_SEL
_SEL
_DATA
_DATA
_DATA
_DATA
_DATA
_DATA
_DATA
_DATA
Reserved
Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10
Table 19. Register Table
DP83849ID
7.1 Register Definition
In the register definitions under the ‘Default’ heading, the following definitions hold true:
— RW=Read Write access
—
—
—
—
—
—
—
—
SC=Register sets on event occurrence and Self-Clears when event ends
RW/SC =Read Write access/Self Clearing bit
RO=Read Only access
COR = Clear on Read
RO/COR=Read Only, Clear on Read
RO/P=Read Only, Permanently set to a default value
LL=Latched Low and held until read, based upon the occurrence of the corresponding event
LH=Latched High and held until read, based upon the occurrence of the corresponding event
48
www.national.com
DP83849ID
7.1.1 Basic Mode Control Register (BMCR)
Table 20. Basic Mode Control Register (BMCR), address 00h
Bit
Bit Name
Default
15
RESET
0, RW/SC
Description
Reset:
1 = Initiate software Reset / Reset in Process.
0 = Normal operation.
This bit, which is self-clearing, returns a value of one until the reset
process is complete. The configuration is re-strapped.
14
LOOPBACK
0, RW
Loopback:
1 = Loopback enabled.
0 = Normal operation.
The loopback function enables MII transmit data to be routed to the MII
receive data path.
Setting this bit may cause the descrambler to lose synchronization and
produce a 500 µs “dead time” before any valid data will appear at the
MII receive outputs.
13
SPEED SELECTION
Strap, RW
Speed Select:
When auto-negotiation is disabled writing to this bit allows the port
speed to be selected.
1 = 100 Mb/s.
0 = 10 Mb/s.
12
AUTO-NEGOTIATION
ENABLE
Strap, RW
Auto-Negotiation Enable:
Strap controls initial value at reset.
If FX is enabled (FX_EN = 1), then this bit will be reset to 0.
1 = Auto-Negotiation Enabled - bits 8 and 13 of this register are ignored when this bit is set.
0 = Auto-Negotiation Disabled - bits 8 and 13 determine the port speed
and duplex mode.
11
POWER DOWN
0, RW
Power Down:
1 = Power down.
0 = Normal operation.
Setting this bit powers down the PHY. Only the register block is enabled during a power down condition. This bit is OR’d with the input
from the PWRDOWN_INT pin. When the active low PWRDOWN_INT
pin is asserted, this bit will be set.
10
ISOLATE
0, RW
Isolate:
1 = Isolates the Port from the MII with the exception of the serial management.
0 = Normal operation.
9
RESTART
AUTO-NEGOTIATION
0, RW/SC
Restart Auto-Negotiation:
1 = Restart Auto-Negotiation. Re-initiates the Auto-Negotiation process. If Auto-Negotiation is disabled (bit 12 = 0), this bit is ignored. This
bit is self-clearing and will return a value of 1 until Auto-Negotiation is
initiated, whereupon it will self-clear. Operation of the Auto-Negotiation
process is not affected by the management entity clearing this bit.
0 = Normal operation.
8
DUPLEX MODE
Strap, RW
Duplex Mode:
When auto-negotiation is disabled writing to this bit allows the port Duplex capability to be selected.
1 = Full Duplex operation.
0 = Half Duplex operation.
49
www.national.com
DP83849ID
Table 20. Basic Mode Control Register (BMCR), address 00h (Continued)
Bit
Bit Name
Default
7
COLLISION
TEST
0, RW
Description
Collision Test:
1 = Collision test enabled.
0 = Normal operation.
When set, this bit will cause the COL signal to be asserted in response
to the assertion of TX_EN within 512-bit times. The COL signal will be
de-asserted within 4-bit times in response to the de-assertion of
TX_EN.
6:0
RESERVED
0, RO
RESERVED: Write ignored, read as 0.
50
www.national.com
DP83849ID
7.1.2 Basic Mode Status Register (BMSR)
Table 21. Basic Mode Status Register (BMSR), address 01h
Bit
Bit Name
Default
15
100BASE-T4
0, RO/P
Description
100BASE-T4 Capable:
0 = Device not able to perform 100BASE-T4 mode.
14
100BASE-TX
1, RO/P
FULL DUPLEX
13
100BASE-TX
1 = Device able to perform 100BASE-TX in full duplex mode.
1, RO/P
HALF DUPLEX
12
10BASE-T
10BASE-T
6
10BASE-T Full Duplex Capable:
1 = Device able to perform 10BASE-T in full duplex mode.
1, RO/P
HALF DUPLEX
10:7
100BASE-TX Half Duplex Capable:
1 = Device able to perform 100BASE-TX in half duplex mode.
1, RO/P
FULL DUPLEX
11
100BASE-TX Full Duplex Capable:
10BASE-T Half Duplex Capable:
1 = Device able to perform 10BASE-T in half duplex mode.
RESERVED
0, RO
RESERVED: Write as 0, read as 0.
MF PREAMBLE
1, RO/P
Preamble suppression Capable:
SUPPRESSION
1 = Device able to perform management transaction with preamble
suppressed, 32-bits of preamble needed only once after reset, invalid
opcode or invalid turnaround.
0 = Normal management operation.
5
AUTO-NEGOTIATION
COMPLETE
0, RO
Auto-Negotiation Complete:
1 = Auto-Negotiation process complete.
0 = Auto-Negotiation process not complete.
4
REMOTE FAULT
0, RO/LH
Remote Fault:
1 = Remote Fault condition detected (cleared on read or by reset).
Fault criteria: Far End Fault Indication or notification from Link Partner of Remote Fault.
0 = No remote fault condition detected.
3
AUTO-NEGOTIATION
ABILITY
1, RO/P
Auto Negotiation Ability:
1 = Device is able to perform Auto-Negotiation.
0 = Device is not able to perform Auto-Negotiation.
2
LINK STATUS
0, RO/LL
Link Status:
1 = Valid link established (for either 10 or 100 Mb/s operation).
0 = Link not established.
The criteria for link validity is implementation specific. The occurrence
of a link failure condition will causes the Link Status bit to clear. Once
cleared, this bit may only be set by establishing a good link condition
and a read via the management interface.
1
JABBER DETECT
0, RO/LH
Jabber Detect: This bit only has meaning in 10 Mb/s mode.
1 = Jabber condition detected.
0 = No Jabber.
This bit is implemented with a latching function, such that the occurrence of a jabber condition causes it to set until it is cleared by a read
to this register by the management interface or by a reset.
0
EXTENDED CAPABILITY
1, RO/P
Extended Capability:
1 = Extended register capabilities.
0 = Basic register set capabilities only.
51
www.national.com
7.1.3 PHY Identifier Register #1 (PHYIDR1)
Table 22. PHY Identifier Register #1 (PHYIDR1), address 02h
Bit
Bit Name
15:0
OUI_MSB
Default
Description
<0010 0000 0000 OUI Most Significant Bits: Bits 3 to 18 of the OUI (080017h) are
0000>, RO/P
stored in bits 15 to 0 of this register. The most significant two bits
of the OUI are ignored (the IEEE standard refers to these as bits 1
and 2).
7.1.4 PHY Identifier Register #2 (PHYIDR2)
Table 23. PHY Identifier Register #2 (PHYIDR2), address 03h
Bit
Bit Name
15:10
OUI_LSB
Default
Description
<0101 11>, RO/P OUI Least Significant Bits:
Bits 19 to 24 of the OUI (080017h) are mapped from bits 15 to 10
of this register respectively.
9:4
VNDR_MDL
<00 1010>, RO/P Vendor Model Number:
The six bits of vendor model number are mapped from bits 9 to 4
(most significant bit to bit 9).
3:0
MDL_REV
<0010>, RO/P
Model Revision Number:
Four bits of the vendor model revision number are mapped from
bits 3 to 0 (most significant bit to bit 3). This field will be incremented
for all major device changes.
7.1.5 Auto-Negotiation Advertisement Register (ANAR)
This register contains the advertised abilities of this device as they will be transmitted to its link partner during Auto-Negotiation. Any writes to this register prior to completion of Auto-Negotiation (as indicated in the Basic Mode Status Register
(address 01h) Auto-Negotiation Complete bit, BMSR[5]) should be followed by a renegotiation. This will ensure that the
new values are properly used in the Auto-Negotiation.
Table 24. Negotiation Advertisement Register (ANAR), address 04h
Bit
Bit Name
Default
15
NP
0, RW
Description
Next Page Indication:
0 = Next Page Transfer not desired.
1 = Next Page Transfer desired.
14
RESERVED
0, RO/P
13
RF
0, RW
RESERVED by IEEE: Writes ignored, Read as 0.
Remote Fault:
1 = Advertises that this device has detected a Remote Fault.
0 = No Remote Fault detected.
12
RESERVED
0, RW
RESERVED for Future IEEE use: Write as 0, Read as 0
52
www.national.com
DP83849ID
The PHY Identifier Registers #1 and #2 together form a unique identifier for the DP83849IDVS. The Identifier consists of
a concatenation of the Organizationally Unique Identifier (OUI), the vendor's model number and the model revision number. A PHY may return a value of zero in each of the 32 bits of the PHY Identifier if desired. The PHY Identifier is intended
to support network management. National's IEEE assigned OUI is 080017h.
Bit
Bit Name
Default
11
ASM_DIR
0, RW
Description
Asymmetric PAUSE Support for Full Duplex Links:
The ASM_DIR bit indicates that asymmetric PAUSE is supported.
Encoding and resolution of PAUSE bits is defined in IEEE 802.3
Annex 28B, Tables 28B-2 and 28B-3, respectively. Pause resolution status is reported in PHYCR[13:12].
1 = Advertise that the DTE (MAC) has implemented both the optional MAC control sublayer and the pause function as specified in
clause 31 and annex 31B of 802.3u.
0= No MAC based full duplex flow control.
10
PAUSE
0, RW
PAUSE Support for Full Duplex Links:
The PAUSE bit indicates that the device is capable of providing the
symmetric PAUSE functions as defined in Annex 31B.
Encoding and resolution of PAUSE bits is defined in IEEE 802.3
Annex 28B, Tables 28B-2 and 28B-3, respectively. Pause resolution status is reported in PHYCR[13:12].
1 = Advertise that the DTE (MAC) has implemented both the optional MAC control sublayer and the pause function as specified in
clause 31 and annex 31B of 802.3u.
0= No MAC based full duplex flow control.
9
T4
0, RO/P
100BASE-T4 Support:
1= 100BASE-T4 is supported by the local device.
0 = 100BASE-T4 not supported.
8
TX_FD
Strap, RW
100BASE-TX Full Duplex Support:
1 = 100BASE-TX Full Duplex is supported by the local device.
0 = 100BASE-TX Full Duplex not supported.
7
TX
Strap, RW
100BASE-TX Support:
1 = 100BASE-TX is supported by the local device.
0 = 100BASE-TX not supported.
6
10_FD
Strap, RW
10BASE-T Full Duplex Support:
1 = 10BASE-T Full Duplex is supported by the local device.
0 = 10BASE-T Full Duplex not supported.
5
10
Strap, RW
10BASE-T Support:
1 = 10BASE-T is supported by the local device.
0 = 10BASE-T not supported.
4:0
SELECTOR
<00001>, RW
Protocol Selection Bits:
These bits contain the binary encoded protocol selector supported
by this port. <00001> indicates that this device supports IEEE
802.3u.
53
www.national.com
DP83849ID
Table 24. Negotiation Advertisement Register (ANAR), address 04h (Continued)
This register contains the advertised abilities of the Link Partner as received during Auto-Negotiation. The content
changes after the successful auto-negotiation if Next-pages are supported.
Table 25. Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page), address 05h
Bit
Bit Name
Default
15
NP
0, RO
Description
Next Page Indication:
0 = Link Partner does not desire Next Page Transfer.
1 = Link Partner desires Next Page Transfer.
14
ACK
0, RO
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word.
0 = Not acknowledged.
The Auto-Negotiation state machine will automatically control the
this bit based on the incoming FLP bursts.
13
RF
0, RO
Remote Fault:
1 = Remote Fault indicated by Link Partner.
0 = No Remote Fault indicated by Link Partner.
12
RESERVED
0, RO
RESERVED for Future IEEE use:
Write as 0, read as 0.
11
ASM_DIR
0, RO
ASYMMETRIC PAUSE:
1 = Asymmetric pause is supported by the Link Partner.
0 = Asymmetric pause is not supported by the Link Partner.
10
PAUSE
0, RO
PAUSE:
1 = Pause function is supported by the Link Partner.
0 = Pause function is not supported by the Link Partner.
9
T4
0, RO
100BASE-T4 Support:
1 = 100BASE-T4 is supported by the Link Partner.
0 = 100BASE-T4 not supported by the Link Partner.
8
TX_FD
0, RO
100BASE-TX Full Duplex Support:
1 = 100BASE-TX Full Duplex is supported by the Link Partner.
0 = 100BASE-TX Full Duplex not supported by the Link Partner.
7
TX
0, RO
100BASE-TX Support:
1 = 100BASE-TX is supported by the Link Partner.
0 = 100BASE-TX not supported by the Link Partner.
6
10_FD
0, RO
10BASE-T Full Duplex Support:
1 = 10BASE-T Full Duplex is supported by the Link Partner.
0 = 10BASE-T Full Duplex not supported by the Link Partner.
5
10
0, RO
10BASE-T Support:
1 = 10BASE-T is supported by the Link Partner.
0 = 10BASE-T not supported by the Link Partner.
4:0
SELECTOR
<0 0000>, RO
Protocol Selection Bits:
Link Partner’s binary encoded protocol selector.
54
www.national.com
DP83849ID
7.1.6 Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page)
Table 26. Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page), address 05h
Bit
Bit Name
Default
15
NP
0, RO
Description
Next Page Indication:
1 = Link Partner desires Next Page Transfer.
0 = Link Partner does not desire Next Page Transfer.
14
ACK
0, RO
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word.
0 = Not acknowledged.
The Auto-Negotiation state machine will automatically control the
this bit based on the incoming FLP bursts. Software should not attempt to write to this bit.
13
MP
0, RO
Message Page:
1 = Message Page.
0 = Unformatted Page.
12
ACK2
0, RO
Acknowledge 2:
1 = Link Partner does have the ability to comply to next page message.
0 = Link Partner does not have the ability to comply to next page
message.
11
TOGGLE
0, RO
Toggle:
1 = Previous value of the transmitted Link Code word equalled 0.
0 = Previous value of the transmitted Link Code word equalled 1.
10:0
CODE
<000 0000 0000>, Code:
RO
This field represents the code field of the next page transmission.
If the MP bit is set (bit 13 of this register), then the code shall be
interpreted as a “Message Page,” as defined in annex 28C of
Clause 28. Otherwise, the code shall be interpreted as an “Unformatted Page,” and the interpretation is application specific.
55
www.national.com
DP83849ID
7.1.7 Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page)
DP83849ID
7.1.8 Auto-Negotiate Expansion Register (ANER)
This register contains additional Local Device and Link Partner status information.
Table 27. Auto-Negotiate Expansion Register (ANER), address 06h
Bit
Bit Name
Default
Description
15:5
RESERVED
0, RO
RESERVED: Writes ignored, Read as 0.
4
PDF
0, RO
Parallel Detection Fault:
1 = A fault has been detected via the Parallel Detection function.
0 = A fault has not been detected.
3
LP_NP_ABLE
0, RO
Link Partner Next Page Able:
1 = Link Partner does support Next Page.
0 = Link Partner does not support Next Page.
2
NP_ABLE
1, RO/P
1
PAGE_RX
0, RO/COR
Next Page Able:
1 = Indicates local device is able to send additional “Next Pages”.
Link Code Word Page Received:
1 = Link Code Word has been received, cleared on a read.
0 = Link Code Word has not been received.
0
LP_AN_ABLE
0, RO
Link Partner Auto-Negotiation Able:
1 = indicates that the Link Partner supports Auto-Negotiation.
0 = indicates that the Link Partner does not support Auto-Negotiation.
56
www.national.com
This register contains the next page information sent by this device to its Link Partner during Auto-Negotiation.
Table 28. Auto-Negotiation Next Page Transmit Register (ANNPTR), address 07h
Bit
Bit Name
Default
15
NP
0, RW
Description
Next Page Indication:
0 = No other Next Page Transfer desired.
1 = Another Next Page desired.
14
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
13
MP
1, RW
Message Page:
1 = Message Page.
0 = Unformatted Page.
12
ACK2
0, RW
Acknowledge2:
1 = Will comply with message.
0 = Cannot comply with message.
Acknowledge2 is used by the next page function to indicate that
Local Device has the ability to comply with the message received.
11
TOG_TX
0, RO
Toggle:
1 = Value of toggle bit in previously transmitted Link Code Word
was 0.
0 = Value of toggle bit in previously transmitted Link Code Word
was 1.
Toggle is used by the Arbitration function within Auto-Negotiation
to ensure synchronization with the Link Partner during Next Page
exchange. This bit shall always take the opposite value of the
Toggle bit in the previously exchanged Link Code Word.
10:0
CODE
<000 0000 0001>, Code:
RW
This field represents the code field of the next page transmission.
If the MP bit is set (bit 13 of this register), then the code shall be
interpreted as a "Message Page”, as defined in annex 28C of
IEEE 802.3u. Otherwise, the code shall be interpreted as an "Unformatted Page”, and the interpretation is application specific.
The default value of the CODE represents a Null Page as defined
in Annex 28C of IEEE 802.3u.
57
www.national.com
DP83849ID
7.1.9 Auto-Negotiation Next Page Transmit Register (ANNPTR)
This register provides a single location within the register set for quick access to commonly accessed information.
Table 29. PHY Status Register (PHYSTS), address 10h
Bit
Bit Name
Default
Description
15
RESERVED
0, RO
RESERVED: Write ignored, read as 0.
14
MDIX MODE
0, RO
MDIX mode as reported by the Auto-Negotiation logic:
This bit will be affected by the settings of the MDIX_EN and
FORCE_MDIX bits in the PHYCR register. When MDIX is enabled,
but not forced, this bit will update dynamically as the Auto-MDIX algorithm swaps between MDI and MDIX configurations.
1 = MDI pairs swapped
(Receive on TPTD pair, Transmit on TPRD pair)
0 = MDI pairs normal
(Receive on TRD pair, Transmit on TPTD pair)
13
RECEIVE ERROR
LATCH
0, RO/LH
Receive Error Latch:
This bit will be cleared upon a read of the RECR register.
1 = Receive error event has occurred since last read of RXERCNT
(address 15h, Page 0).
0 = No receive error event has occurred.
12
POLARITY STATUS
0, RO
Polarity Status:
This bit is a duplication of bit 4 in the 10BTSCR register. This bit will
be cleared upon a read of the 10BTSCR register, but not upon a
read of the PHYSTS register.
1 = Inverted Polarity detected.
0 = Correct Polarity detected.
11
FALSE CARRIER
SENSE LATCH
0, RO/LH
False Carrier Sense Latch:
This bit will be cleared upon a read of the FCSR register.
1 = False Carrier event has occurred since last read of FCSCR (address 14h).
0 = No False Carrier event has occurred.
10
SIGNAL DETECT
0, RO/LL
100Base-TX qualified Signal Detect from PMA:
This is the SD that goes into the link monitor. It is the AND of raw
SD and descrambler lock, when address 16h, bit 8 (page 0) is set.
When this bit is cleared, it will be equivalent to the raw SD from the
PMD.
9
DESCRAMBLER
LOCK
0, RO/LL
8
PAGE RECEIVED
0, RO
100Base-TX Descrambler Lock from PMD.
Link Code Word Page Received:
This is a duplicate of the Page Received bit in the ANER register,
but this bit will not be cleared upon a read of the PHYSTS register.
1 = A new Link Code Word Page has been received. Cleared on
read of the ANER (address 06h, bit 1).
0 = Link Code Word Page has not been received.
7
MII INTERRUPT
0, RO
MII Interrupt Pending:
1 = Indicates that an internal interrupt is pending. Interrupt source
can be determined by reading the MISR Register (12h). Reading
the MISR will clear the Interrupt.
0 = No interrupt pending.
58
www.national.com
DP83849ID
7.1.10 PHY Status Register (PHYSTS)
Bit
Bit Name
Default
6
REMOTE FAULT
0, RO
Description
Remote Fault:
1 = Remote Fault condition detected (cleared on read of BMSR (address 01h) register or by reset). Fault criteria: notification from Link
Partner of Remote Fault via Auto-Negotiation.
0 = No remote fault condition detected.
5
JABBER DETECT
0, RO
Jabber Detect: This bit only has meaning in 10 Mb/s mode
This bit is a duplicate of the Jabber Detect bit in the BMSR register,
except that it is not cleared upon a read of the PHYSTS register.
1 = Jabber condition detected.
0 = No Jabber.
4
AUTO-NEG COMPLETE
0, RO
LOOPBACK STATUS
0, RO
Auto-Negotiation Complete:
1 = Auto-Negotiation complete.
0 = Auto-Negotiation not complete.
3
Loopback:
1 = Loopback enabled.
0 = Normal operation.
2
DUPLEX STATUS
0, RO
Duplex:
This bit indicates duplex status and is determined from Auto-Negotiation or Forced Modes.
1 = Full duplex mode.
0 = Half duplex mode.
Note: This bit is only valid if Auto-Negotiation is enabled and complete and there is a valid link or if Auto-Negotiation is disabled and
there is a valid link.
1
SPEED STATUS
0, RO
Speed10:
This bit indicates the status of the speed and is determined from
Auto-Negotiation or Forced Modes.
1 = 10 Mb/s mode.
0 = 100 Mb/s mode.
Note: This bit is only valid if Auto-Negotiation is enabled and complete and there is a valid link or if Auto-Negotiation is disabled and
there is a valid link.
0
LINK STATUS
0, RO
Link Status:
This bit is a duplicate of the Link Status bit in the BMSR register,
except that it will not be cleared upon a read of the PHYSTS register.
1 = Valid link established (for either 10 or 100 Mb/s operation)
0 = Link not established.
59
www.national.com
DP83849ID
Table 29. PHY Status Register (PHYSTS), address 10h
This register implements the MII Interrupt PHY Specific Control register. Sources for interrupt generation include: Energy
Detect State Change, Link State Change, Speed Status Change, Duplex Status Change, Auto-Negotiation Complete or
any of the counters becoming half-full. The individual interrupt events must be enabled by setting bits in the MII Interrupt
Status and Event Control Register (MISR).
Table 30. MII Interrupt Control Register (MICR), address 11h
Bit
Bit Name
Default
15:3
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
Description
2
TINT
0, RW
Test Interrupt:
Forces the PHY to generate an interrupt to facilitate interrupt testing. Interrupts will continue to be generated as long as this bit remains set.
1 = Generate an interrupt
0 = Do not generate interrupt
1
INTEN
0, RW
Interrupt Enable:
Enable interrupt dependent on the event enables in the MISR register.
1 = Enable event based interrupts
0 = Disable event based interrupts
0
INT_OE
0, RW
Interrupt Output Enable:
Enable interrupt events to signal via the PWRDOWN_INT pin by
configuring the PWRDOWN_INT pin as an output.
1 = PWRDOWN_INT is an Interrupt Output
0 = PWRDOWN_INT is a Power Down Input
7.1.12 MII Interrupt Status and Misc. Control Register (MISR)
This register contains event status and enables for the interrupt function. If an event has occurred since the last read of
this register, the corresponding status bit will be set. If the corresponding enable bit in the register is set, an interrupt will
be generated if the event occurs. The MICR register controls must also be set to allow interrupts. The status indications
in this register will be set even if the interrupt is not enabled.
Table 31. MII Interrupt Status and Misc. Control Register (MISR), address 12h
15
LQ_INT
0, RO/COR
Link Quality interrupt:
1 = Link Quality interrupt is pending and is cleared by the current
read.
0 = No Link Quality interrupt pending.
14
ED_INT
0, RO/COR
Energy Detect interrupt:
1 = Energy detect interrupt is pending and is cleared by the current
read.
0 = No energy detect interrupt pending.
13
LINK_INT
0, RO/COR
Change of Link Status interrupt:
1 = Change of link status interrupt is pending and is cleared by the
current read.
0 = No change of link status interrupt pending.
12
SPD_INT
0, RO/COR
Change of speed status interrupt:
1 = Speed status change interrupt is pending and is cleared by the
current read.
0 = No speed status change interrupt pending.
60
www.national.com
DP83849ID
7.1.11 MII Interrupt Control Register (MICR)
11
DUP_INT
0, RO/COR
Change of duplex status interrupt:
1 = Duplex status change interrupt is pending and is cleared by
the current read.
0 = No duplex status change interrupt pending.
10
ANC_INT
0, RO/COR
Auto-Negotiation Complete interrupt:
1 = Auto-negotiation complete interrupt is pending and is cleared
by the current read.
0 = No Auto-negotiation complete interrupt pending.
9
FHF_INT
0, RO/COR
False Carrier Counter half-full interrupt:
1 = False carrier counter half-full interrupt is pending and is
cleared by the current read.
0 = No false carrier counter half-full interrupt pending.
8
RHF_INT
0, RO/COR
Receive Error Counter half-full interrupt:
1 = Receive error counter half-full interrupt is pending and is
cleared by the current read.
0 = No receive error carrier counter half-full interrupt pending.
7
LQ_INT_EN
0, RW
Enable Interrupt on Link Quality Monitor event
6
ED_INT_EN
0, RW
Enable Interrupt on energy detect event
5
LINK_INT_EN
0, RW
Enable Interrupt on change of link status
4
SPD_INT_EN
0, RW
Enable Interrupt on change of speed status
3
DUP_INT_EN
0, RW
Enable Interrupt on change of duplex status
2
ANC_INT_EN
0, RW
Enable Interrupt on Auto-negotiation complete event
1
FHF_INT_EN
0, RW
Enable Interrupt on False Carrier Counter Register half-full event
0
RHF_INT_EN
0, RW
Enable Interrupt on Receive Error Counter Register half-full event
7.1.13 Page Select Register (PAGESEL)
This register is used to enable access to the Link Diagnostics Registers.
Table 32. Page Select Register (PAGESEL), address 13h
Bit
Bit Name
Default
15:2
RESERVED
0, RO
RESERVED: Writes ignored, Read as 0
Description
1:0
PAGE_SEL
0, RW
Page_Sel Bit:
Selects between paged registers for address 14h to 1Fh.
0 = Extended Registers Page 0
1 = RESERVED
2 = Link Diagnostics Registers Page 2
61
www.national.com
DP83849ID
Table 31. MII Interrupt Status and Misc. Control Register (MISR), address 12h
7.2.1 False Carrier Sense Counter Register (FCSCR)
This counter provides information required to implement the “False Carriers” attribute within the MAU managed object
class of Clause 30 of the IEEE 802.3u specification.
Table 33. False Carrier Sense Counter Register (FCSCR), address 14h
Bit
Bit Name
Default
15:8
RESERVED
0, RO
7:0
FCSCNT[7:0]
0, RO/COR
Description
RESERVED: Writes ignored, Read as 0
False Carrier Event Counter:
This 8-bit counter increments on every false carrier event. This
counter sticks when it reaches its max count (FFh).
7.2.2 Receiver Error Counter Register (RECR)
This counter provides information required to implement the “Symbol Error During Carrier” attribute within the PHY managed object class of Clause 30 of the IEEE 802.3u specification.
Table 34. Receiver Error Counter Register (RECR), address 15h
Bit
Bit Name
Default
15:8
RESERVED
0, RO
7:0
RXERCNT[7:0]
0, RO/COR
Description
RESERVED: Writes ignored, Read as 0
RX_ER Counter:
When a valid carrier is present and there is at least one occurrence
of an invalid data symbol, this 8-bit counter increments for each receive error detected. This event can increment only once per valid
carrier event. If a collision is present, the attribute will not increment. The counter sticks when it reaches its max count.
7.2.3 100 Mb/s PCS Configuration and Status Register (PCSR)
This register contains control and status information for the 100BASE Physical Coding Sublayer.
Table 35. 100 Mb/s PCS Configuration and Status Register (PCSR), address 16h
Bit
Bit Name
Default
15:12
RESERVED
<00>, RO
11
FREE_CLK
0, RW
Description
RESERVED: Writes ignored, Read as 0.
Receive Clock:
1 = RX_CLK is free-running
0 = RX_CLK phase adjusted based on alignment
10
TQ_EN
0, RW
100Mbs True Quiet Mode Enable:
1 = Transmit True Quiet Mode.
0 = Normal Transmit Mode.
9
SD FORCE PMA
0, RW
Signal Detect Force PMA:
1 = Forces Signal Detection in PMA.
0 = Normal SD operation.
62
www.national.com
DP83849ID
7.2 Extended Registers - Page 0
Bit
Bit Name
Default
8
SD_OPTION
1, RW
Description
Signal Detect Option:
1 = Default operation. Link will be asserted following detection of
valid signal level and Descrambler Lock. Link will be maintained as
long as signal level is valid. A loss of Descrambler Lock will not
cause Link Status to drop.
0 = Modified signal detect algorithm. Link will be asserted following
detection of valid signal level and Descrambler Lock. Link will be
maintained as long as signal level is valid and Descrambler remains locked.
7
DESC_TIME
0, RW
Descrambler Timeout:
Increase the descrambler timeout. When set this should allow the
device to receive larger packets (>9k bytes) without loss of synchronization.
1 = 2ms
0 = 722us (per ANSI X3.263: 1995 (TP-PMD) 7.2.3.3e)
6
FX_EN
Strap, RW
FX Fiber Mode Enable:
This bit is set when the FX_EN strap option is selected (pulled high)
for the respective port.
1 = Enables FX operation
0 = Disables FX operation
5
FORCE_100_OK
0, RW
Force 100Mb/s Good Link:
1 = Forces 100Mb/s Good Link.
0 = Normal 100Mb/s operation.
4
RESERVED
0, RO
RESERVED: Writes ignored, Read as 0
3
FEFI_EN
Strap, RW
Far End Fault Indication Mode Enable:
This bit is set when the FX_EN strap option is selected for the respective port.
1 = FEFI Mode Enabled
0 = FEFI Mode Disabled
2
NRZI_BYPASS
0, RW
NRZI Bypass Enable:
1 = NRZI Bypass Enabled.
0 = NRZI Bypass Disabled.
1
SCRAM
Strap, RW
BYPASS
Scrambler Bypass Enable:
This bit is set when the FX_EN strap option is selected for the respective port. In the FX mode, the scrambler is bypassed.
1 = Scrambler Bypass Enabled
0 = Scrambler Bypass Disabled
0
DESCRAM
BYPASS
Strap, RW
Descrambler Bypass Enable:
This bit is set when the FX_EN strap option is selected for the respective port. In the FX mode, the descrambler is bypassed.
1 = Descrambler Bypass Enabled
0 = Descrambler Bypass Disabled
63
www.national.com
DP83849ID
Table 35. 100 Mb/s PCS Configuration and Status Register (PCSR), address 16h (Continued)
This register configures the RMII/MII Interface Mode of operation. This register controls selecting MII or RMII mode for
Receive or Transmit. In addition, several additional bits are included to allow datapath selection for Transmit and Receive
in multiport applications.
Table 36. RMII and Bypass Register (RBR), addresses 17h
Bit
Bit Name
Default
15
SIM_WRITE
0, RW
Description
Simultaneous Write:
Setting this bit in port A register space enables simultaneous write to Phy
registers in both ports. Subsequent writes to port A registers will write to
registers in both ports A and B.
1 = Simultaneous writes to both ports
0 = Per-port write
14
RESERVED
0, RO
RESERVED: Writes ignored, Read as 0
13
DIS_TX_OPT
0, RW
Disable RMII TX Latency Optimization:
Normally the RMII Transmitter will minimize the transmit latency by
realigning the transmit clock with the Reference clock phase at the
start of a packet transmission. Setting this bit will disable Phase realignment and ensure that IDLE bits will always be sent in multiples
of the symbol size. This will result in a larger uncertainty in RMII
transmit latency.
12:9
RESERVED
0
RESERVED:
Must be zero.
8
PMD_LOOP
0, RW
PMD Loopback:
0= Normal Operation
1= Remote (PMD) Loopback
Setting this bit will cause the device to Loopback data received
from the Physical Layer. The loopback is done prior to the MII or
RMII interface. Data received at the internal MII or RMII interface
will be applied to the transmitter. This mode should only be used if
RMII mode is enabled.
7:6
RESERVED
0
5
RMII_MODE
Strap, RW
RESERVED:
Must be zero.
Reduced MII Mode:
0 = Standard MII Mode
1 = Reduced MII Mode
4
RMII_REV1_0
0, RW
Reduced MII Revision 1.0:
0 = (RMII revision 1.2) CRS_DV will toggle at the end of a packet
to indicate deassertion of CRS.
1 = (RMII revision 1.0) CRS_DV will remain asserted until final data
is transferred. CRS_DV will not toggle at the end of a packet.
3
RX_OVF_STS
0, RO/COR
RX FIFO Over Flow Status:
0 = Normal
1 = Overflow detected
2
RX_UNF_STS
0, RO/COR
RX FIFO Under Flow Status:
0 = Normal
1 = Underflow detected
1:0
ELAST_BUF[1:0]
01, RW
Receive Elasticity Buffer:
This field controls the Receive Elasticity Buffer which allows for frequency variation tolerance between the 50MHz RMII clock and the
recovered data. See Section 3.2 for more information on Elasticity
Buffer settings in RMII mode.
64
www.national.com
DP83849ID
7.2.4 RMII and Bypass Register (RBR)
This register provides the ability to directly control any or all LED outputs. It does not provide read access to LEDs. In
addition, it provides control for the Activity source and blinking LED frequency.
Table 37. LED Direct Control Register (LEDCR), address 18h
Bit
Bit Name
Default
Description
15:9
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
8
LEDACT_RX
0, RW
1 = Activity is only indicated for Receive traffic
0 = Activity is indicated for Transmit or Receive traffic
7:6
BLINK_FREQ
00, RW
LED Blink Frequency
These bits control the blink frequency of the LED_LINK output
when blinking on activity is enabled.
0 = 6Hz
1 = 12Hz
2 = 24Hz
3 = 48Hz
5
DRV_SPDLED
0, RW
1 = Drive value of SPDLED bit onto LED_SPEED output
0 = Normal operation
4
DRV_LNKLED
0, RW
1 = Drive value of LNKLED bit onto LED_LINK output
0 = Normal operation
3
DRV_ACTLED
0, RW
1 = Drive value of ACTLED bit onto LED_ACT/LED_COL output
0 = Normal operation
2
SPDLED
0, RW
Value to force on LED_SPEED output
1
LNKLED
0, RW
Value to force on LED_LINK output
0
ACTLED
0, RW
Value to force on LED_ACT/LED_COL output
65
www.national.com
DP83849ID
7.2.5 LED Direct Control Register (LEDCR)
This register provides control for Phy functions such as MDIX, BIST, LED configuration, and Phy address. It also provides Pause Negotiation status.
Table 38. PHY Control Register (PHYCR), address 19h
Bit
Bit Name
Default
15
MDIX_EN
Strap, RW
Description
Auto-MDIX Enable:
1 = Enable Auto-neg Auto-MDIX capability.
0 = Disable Auto-neg Auto-MDIX capability.
The Auto-MDIX algorithm requires that the Auto-Negotiation Enable bit in the BMCR register to be set. If Auto-Negotiation is not
enabled, Auto-MDIX should be disabled as well.
14
FORCE_MDIX
0, RW
Force MDIX:
1 = Force MDI pairs to cross.
(Receive on TPTD pair, Transmit on TPRD pair)
0 = Normal operation.
13
PAUSE_RX
0, RO
Pause Receive Negotiated:
Indicates that pause receive should be enabled in the MAC. Based
on ANAR[11:10] and ANLPAR[11:10] settings.
This function shall be enabled according to IEEE 802.3 Annex 28B
Table 28B-3, “Pause Resolution”, only if the Auto-Negotiated Highest Common Denominator is a full duplex technology.
12
PAUSE_TX
0, RO
Pause Transmit Negotiated:
Indicates that pause transmit should be enabled in the MAC. Based
on ANAR[11:10] and ANLPAR[11:10] settings.
This function shall be enabled according to IEEE 802.3 Annex 28B
Table 28B-3, “Pause Resolution”, only if the Auto-Negotiated Highest Common Denominator is a full duplex technology.
11
BIST_FE
0, RW/SC
BIST Force Error:
1 = Force BIST Error.
0 = Normal operation.
This bit forces a single error, and is self clearing.
10
PSR_15
0, RW
BIST Sequence select:
1 = PSR15 selected.
0 = PSR9 selected.
9
BIST_STATUS
0, LL/RO
BIST Test Status:
1 = BIST pass.
0 = BIST fail. Latched, cleared when BIST is stopped.
For a count number of BIST errors, see the BIST Error Count in the
CDCTRL1 register.
8
BIST_START
0, RW
BIST Start:
1 = BIST start.
0 = BIST stop.
7
BP_STRETCH
0, RW
Bypass LED Stretching:
This will bypass the LED stretching and the LEDs will reflect the internal value.
1 = Bypass LED stretching.
0 = Normal operation.
66
www.national.com
DP83849ID
7.2.6 PHY Control Register (PHYCR)
DP83849ID
Table 38. PHY Control Register (PHYCR), address 19h (Continued)
Bit
Bit Name
Default
6
LED_CNFG[1]
0, RW
5
LED_CNFG[0]
Strap, RW
Description
LED Configuration
LED_CNFG[1]
Don’t care
0
1
LED_ CNFG[0]
1
0
0
Mode Description
Mode 1
Mode 2
Mode 3
In Mode 1, LEDs are configured as follows:
LED_LINK = ON for Good Link, OFF for No Link
LED_SPEED = ON in 100 Mb/s, OFF in 10 Mb/s
LED_ACT/LED_COL = ON for Activity, OFF for No Activity
In Mode 2, LEDs are configured as follows:
LED_LINK = ON for good Link, BLINK for Activity
LED_SPEED = ON in 100 Mb/s, OFF in 10 Mb/s
LED_ACT/LED_COL = ON for Collision, OFF for No Collision
Full Duplex, OFF for Half Duplex
In Mode 3, LEDs are configured as follows:
LED_LINK = ON for Good Link, BLINK for Activity
LED_SPEED = ON in 100 Mb/s, OFF in 10 Mb/s
LED_ACT/LED_COL = ON for Full Duplex, OFF for Half Duplex
4:0
PHYADDR[4:0]
Strap, RW
PHY Address: PHY address for port.
7.2.7 10 Base-T Status/Control Register (10BTSCR)
This register is used for control and status for 10BASE-T device operation.
Table 39. 10Base-T Status/Control Register (10BTSCR), address 1Ah
Bit
Bit Name
Default
15
10BT_SERIAL
Strap, RW
Description
10Base-T Serial Mode (SNI)
1 = Enables 10Base-T Serial Mode
0 = Normal Operation
Places 10 Mb/s transmit and receive functions in Serial Network
Interface (SNI) Mode of operation. Has no effect on 100 Mb/s
operation.
14:12
RESERVED
0, RW
RESERVED:
Must be zero.
11:9
SQUELCH
100, RW
Squelch Configuration:
Used to set the Squelch ‘ON’ threshold for the receiver.
Default Squelch ON is 330mV peak.
67
www.national.com
Bit
Bit Name
Default
8
LOOPBACK_10_DIS
0, RW
Description
10Base-T Loopback Disable:
In half-duplex mode, default 10BASE-T operation loops Transmit
data to the Receive data in addition to transmitting the data on the
physical medium. This is for consistency with earlier 10BASE2 and
10BASE5 implementations which used a shared medium. Setting
this bit disables the loopback function.
This bit does not affect loopback due to setting BMCR[14].
7
LP_DIS
0, RW
Normal Link Pulse Disable:
1 = Transmission of NLPs is disabled.
0 = Transmission of NLPs is enabled.
6
FORCE_LINK_10
0, RW
Force 10Mb Good Link:
1 = Forced Good 10Mb Link.
0 = Normal Link Status.
5
RESERVED
0, RW
4
POLARITY
RO/LH
RESERVED:
Must be zero.
10Mb Polarity Status:
This bit is a duplication of bit 12 in the PHYSTS register. Both bits
will be cleared upon a read of 10BTSCR register, but not upon a
read of the PHYSTS register.
1 = Inverted Polarity detected.
0 = Correct Polarity detected.
3
RESERVED
0, RW
RESERVED:
Must be zero.
2
RESERVED
1, RW
RESERVED:
Must be set to one.
1
HEARTBEAT_DIS
0, RW
Heartbeat Disable: This bit only has influence in half-duplex 10Mb
mode.
1 = Heartbeat function disabled.
0 = Heartbeat function enabled.
When the device is operating at 100Mb or configured for full
duplex operation, this bit will be ignored - the heartbeat function is disabled.
0
JABBER_DIS
0, RW
Jabber Disable:
Applicable only in 10BASE-T.
1 = Jabber function disabled.
0 = Jabber function enabled.
68
www.national.com
DP83849ID
Table 39. 10Base-T Status/Control Register (10BTSCR), address 1Ah (Continued)
This register controls test modes for the 10BASE-T Common Driver. In addition it contains extended control
and status for the packet BIST function.
Table 40. CD Test and BIST Extensions Register (CDCTRL1), address 1Bh
Bit
Bit Name
Default
15:8
BIST_ERROR_COUNT
0, RO
Description
BIST ERROR Counter:
Counts number of errored data nibbles during Packet BIST. This
value will reset when Packet BIST is restarted. The counter sticks
when it reaches its max count.
7:6
RESERVED
0, RW
RESERVED:
Must be zero.
5
BIST_CONT_MODE
0, RW
Packet BIST Continuous Mode:
Allows continuous pseudo random data transmission without any
break in transmission. This can be used for transmit VOD testing.
This is used in conjunction with the BIST controls in the PHYCR
Register (19h). For 10Mb operation, jabber function must be disabled, bit 0 of the 10BTSCR (1Ah), JABBER_DIS = 1.
4
CDPATTEN_10
0, RW
CD Pattern Enable for 10Mb:
1 = Enabled.
0 = Disabled.
3
RESERVED
0, RW
RESERVED:
Must be zero.
2
10MEG_PATT_GAP
0, RW
Defines gap between data or NLP test sequences:
1 = 15 µs.
0 = 10 µs.
1:0
CDPATTSEL[1:0]
00, RW
CD Pattern Select[1:0]:
If CDPATTEN_10 = 1:
00 = Data, EOP0 sequence
01 = Data, EOP1 sequence
10 = NLPs
11 = Constant Manchester 1s (10MHz sine wave) for harmonic distortion testing.
7.2.9 Phy Control Register 2 (PHYCR2)
This register provides additional general control.
Table 41. Phy Control Register 2 (PHYCR2), address 1Ch
Bit
Bit Name
Default
15:10
RESERVED
0, RO
9
SOFT_RESET
0, RW/SC
Description
RESERVED: Writes ignored, read as 0.
Soft Reset:
Resets the entire device minus the registers - all configuration is
preserved.
1= Reset, self-clearing.
8:0
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
69
www.national.com
DP83849ID
7.2.8 CD Test and BIST Extensions Register (CDCTRL1)
DP83849ID
7.2.10 Energy Detect Control (EDCR)
This register provides control and status for the Energy Detect function.
Table 42. Energy Detect Control (EDCR), address 1Dh
Bit
Bit Name
Default
15
ED_EN
Strap, RW
Description
Energy Detect Enable:
Allow Energy Detect Mode.
When Energy Detect is enabled and Auto-Negotiation is disabled
via the BMCR register, Auto-MDIX should be disabled via the PHYCR register.
14
ED_AUTO_UP
1, RW
Energy Detect Automatic Power Up:
Automatically begin power up sequence when Energy Detect Data
Threshold value (EDCR[3:0]) is reached. Alternatively, device
could be powered up manually using the ED_MAN bit (ECDR[12]).
13
ED_AUTO_DOWN
1, RW
Energy Detect Automatic Power Down:
Automatically begin power down sequence when no energy is detected. Alternatively, device could be powered down using the
ED_MAN bit (EDCR[12]).
12
ED_MAN
0, RW/SC
Energy Detect Manual Power Up/Down:
Begin power up/down sequence when this bit is asserted. When
set, the Energy Detect algorithm will initiate a change of Energy Detect state regardless of threshold (error or data) and timer values.
In managed applications, this bit can be set after clearing the Energy Detect interrupt to control the timing of changing the power
state.
11
ED_BURST_DIS
0, RW
Energy Detect Burst Disable:
Disable bursting of energy detect data pulses. By default, Energy
Detect (ED) transmits a burst of 4 ED data pulses each time the CD
is powered up. When bursting is disabled, only a single ED data
pulse will be send each time the CD is powered up.
10
ED_PWR_STATE
0, RO
Energy Detect Power State:
Indicates current Energy Detect Power state. When set, Energy
Detect is in the powered up state. When cleared, Energy Detect is
in the powered down state. This bit is invalid when Energy Detect
is not enabled.
9
ED_ERR_MET
0, RO/COR
Energy Detect Error Threshold Met:
No action is automatically taken upon receipt of error events. This
bit is informational only and would be cleared on a read.
8
ED_DATA_MET
0, RO/COR
Energy Detect Data Threshold Met:
The number of data events that occurred met or surpassed the Energy Detect Data Threshold. This bit is cleared on a read.
7:4
ED_ERR_COUNT
0001, RW
Energy Detect Error Threshold:
Threshold to determine the number of energy detect error events
that should cause the device to take action. Intended to allow averaging of noise that may be on the line. Counter will reset after approximately 2 seconds without any energy detect data events.
3:0
ED_DATA_COUNT
0001, RW
Energy Detect Data Threshold:
Threshold to determine the number of energy detect events that
should cause the device to take actions. Intended to allow averaging of noise that may be on the line. Counter will reset after approximately 2 seconds without any energy detect data events.
70
www.national.com
Page 2 Link Diagnostics Registers are accessible by setting bits [1:0] = 10 of PAGESEL (13h).
7.3.1 100Mb Length Detect Register (LEN100_DET), Page 2, address 14h
This register contains linked cable length estimation in 100Mb operation. The cable length is an estimation of the effective cable length based on the characteristics of the recovered signal. The cable length is valid only during 100Mb operation with a valid Link status indication.
Table 43. 100Mb Length Detect Register (LEN100_DET), address 14h
Bit
Bit Name
Default
Description
15:8
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
7:0
CABLE_LEN
0, RO
Cable Length Estimate:
Indicates an estimate of effective cable length in meters. A value
of FF indicates cable length cannot be determined.
7.3.2 100Mb Frequency Offset Indication Register (FREQ100), Page 2, address 15h
This register returns an indication of clock frequency offset relative to the link partner. Two values can be read, the long
term Frequency Offset, or a short term Frequency Control value. The Frequency Control value includes short term
phase correction. The variance between the Frequency Control value and the Frequency Offset can be used as an indication of the amount of jitter in the system.
Table 44. 100Mb Frequency Offset Indication Register (FREQ100), address 15h
Bit
Bit Name
Default
15
SAMPLE_FREQ
0, RW
Description
Sample Frequency Offset:
If Sel_FC is set to a 0, then setting this bit to a 1 will poll the DSP
for the long-term Frequency Offset value. The value will be available in the Freq_Offset bits of this register.
If Sel_FC is set to a 1, then setting this bit to a 1 will poll the DSP
for the current Frequency Control value. The value will be available
in the Freq_Offset bits of this register.
This register bit will always read back as 0.
14:9
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
8
SEL_FC
0, RW
Select Frequency Control:
Setting this bit to a 1 will select the current Frequency Control value
instead of the Frequency Offset. This value contains Frequency
Offset plus the short term phase correction and can be used to indicate amount of jitter in the system. The value will be available in
the Freq_Offset bits of this register.
7:0
FREQ_OFFSET
0, RO
Frequency Offset:
Frequency offset value loaded from the DSP following assertion of
the Sample_Freq control bit. The Frequency Offset or Frequency
Control value is a twos-complement signed value in units of approximately 5.1562ppm. The range is as follows:
0x7F = +655ppm
0x00 = 0ppm
0x80 = -660ppm
71
www.national.com
DP83849ID
7.3 Link Diagnostics Registers - Page 2
This register contains control for the Time Domain Reflectometry (TDR) cable diagnostics. The TDR cable diagnostics
sends pulses down the cable and captures reflection data to be used to estimate cable length and detect certain cabling
faults.
Table 45. TDR Control Register (TDR_CTRL), address 16h
Bit
Bit Name
Default
15
TDR_ENABLE
0, RW
Description
TDR Enable:
Enable TDR mode. This forces powerup state to correct operating
condition for sending and receiving TDR pulses.
14
TDR_100Mb
0, RW
TDR 100Mb:
Sets TDR controller to use the 100Mb Transmitter. This allows for
sending pulse widths in multiples of 8ns. Pulses in 100Mb mode
will alternate between positive pulses and negative pulses.
Default operation uses the 10Mb Link Pulse generator. Pulses may
include just the 50ns preemphasis portion of the pulse or the 100ns
full link pulse (as controlled by setting TDR Width).
13
TX_CHANNEL
0, RW
Transmit Channel Select:
Select transmit channel for sending pulses. Pulse can be sent on
the Transmit or Receive pair.
0 : Transmit channel
1 : Receive channel
12
RX_CHANNEL
0, RW
Receive Channel Select:
Select receive channel for detecting pulses. Pulse can be monitored on the Transmit or Receive pair.
0 : Transmit channel
1 : Receive channel
11
SEND_TDR
0, RW/SC
Send TDR Pulse:
Setting this bit will send a TDR pulse and enable the monitor circuit
to capture the response. This bit will automatically clear when the
capture is complete.
10:8
TDR_WIDTH
0, RW
TDR Pulse Width:
Pulse width in clocks for the transmitted pulse. In 100Mb mode,
pulses are in 8ns increments. In 10Mb mode, pulses are in 50ns
increments, but only 50ns or 100ns pulses can be sent. Sending a
pulse of 0 width will not transmit a pulse, but allows for baseline
testing.
7
TDR_MIN_MODE
0, RW
Min/Max Mode control:
This bit controls direction of the pulse to be detected. Default looks
for a positive peak. Threshold and peak values will be interpreted
appropriately based on this bit.
0 : Max Mode, detect positive peak
1 : Min Mode, detect negative peak
6
RESERVED
5:0
RX_THRESHOLD
0, RO
RESERVED: Writes ignored, read as 0.
<10_0000>, RW RX Threshold:
This value provides a threshold for measurement to the start of a
peak. If Min Mode is set to 0, data must be greater than this value
to trigger a capture. If Min Mode is 1, data must be less than this
value to trigger a capture. Data ranges from 0x00 to 0x3F, with
0x20 as the midpoint. Positive data is greater than 0x20, negative
data is less than 0x20.
72
www.national.com
DP83849ID
7.3.3 TDR Control Register (TDR_CTRL), Page 2, address 16h
This register contains sample window control for the Time Domain Reflectometry (TDR) cable diagnostics. The two values contained in this register specify the beginning and end times for the window to monitor the response to the transmitted pulse. Time values are in 8ns increments. This provides a method to search for multiple responses and also to
screen out the initial outgoing pulse.
Table 46. TDR Window Register (TDR_WIN), address 17h
Bit
Bit Name
Default
15:8
TDR_START
0, RW
Description
TDR Start Window:
Specifies start time for monitoring TDR response.
7:0
TDR_STOP
0xFF, RW
TDR Stop Window:
Specifies stop time for monitoring TDR response. The Stop Window should be set to a value greater than or equal to the Start Window.
7.3.5 TDR Peak Register (TDR_PEAK), Page 2, address 18h
This register contains the results of the TDR Peak Detection. Results are valid if the TDR_CTRL[11] is clear following
sending the TDR pulse.
Table 47. TDR Peak Register (TDR_PEAK), address 18h
Bit
Bit Name
Default
15:14
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
Description
13:8
TDR_PEAK
0, RO
TDR Peak Value:
This register contains the peak value measured during the TDR
sample window. If Min Mode control (TDR_CTRL[7]) is 0, this contains the maximum detected value. If Min Mode control is 1, this
contains the minimum detected value.
7:0
TDR_PEAK_TIME
0, RO
TDR Peak Time:
Specifies the time for the first occurrence of the peak value.
7.3.6 TDR Threshold Register (TDR_THR), Page 2, address 19h
This register contains the results of the TDR Threshold Detection. Results are valid if the TDR_CTRL[11] is clear following sending the TDR pulse.
Table 48. TDR Threshold Register (TDR_THR), address 19h
Bit
Bit Name
Default
15:9
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
Description
8
TDR_THR_MET
0, RO
TDR Threshold Met:
This bit indicates the TDR threshold was met during the sample
window. A value of 0 indicates the threshold was not met.
7:0
TDR_THR_TIME
0, RO
TDR Threshold Time:
Specifies the time for the first data that met the TDR threshold.
This field is only valid if the threshold was met.
73
www.national.com
DP83849ID
7.3.4 TDR Window Register (TDR_WIN), Page 2, address 17h
The Variance Control and Data Registers provide control and status for the Cable Signal Quality Estimation function.
The Cable Signal Quality Estimation allows a simple method of determining an approximate Signal-to-Noise Ratio for the
100Mb receiver. This register contains the programmable controls and status bits for the variance computation, which
can be used to make a simple Signal-to-Noise Ratio estimation.
Table 49. Variance Control Register (VAR_CTRL), address 1Ah
Bit
15
Bit Name
Default
VAR_RDY
0, RO
Description
Variance Data Ready Status:
Indicates new data is available in the Variance data register. This
bit will be automatically cleared after two consecutive reads ot
VAR_DATA.
14:4
3
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
VAR_FREEZE
0, RW
Freeze Variance Registers:
Freeze VAR_DATA register.
This bit is ensures that VAR_DATA register is frozen for software
reads. This bit is automatically cleared after two consecutive reads
of VAR_DATA.
2:1
VAR_TIMER
0, RW
Variance Computation Timer (in ms):
Selects the Variance computation timer period. After a new value
is written, computation is automatically restarted. New variance
register values are loaded after the timer elapses.
Var_Timer = 0 => 2 ms timer (default)
Var_Timer = 1 => 4 ms timer
Var_Timer = 2 => 6 ms timer
Var_Timer = 3 => 8 ms timer
Time units are actually 217 cycles of an 8ns clock, or 1.048576ms.
0
VAR_ENABLE
0, RW
Variance Enable:
Enable Variance computation. Off by default.
7.3.8 Variance Data Register (VAR_DATA), Page 2, address 1Bh
This register contains the 32-bit Variance Sum. The contents of the data are valid only when VAR_RDY is asserted in the
VAR_CTRL register. Upon detection of VAR_RDY asserted, software should set the VAR_FREEZE bit in the VAR_CTRL
register to prevent loading of a new value into the VAR_DATA register. Since the Variance Data value is 32-bits, two
reads of this register are required to get the full value.
Table 50. Variance Data Register (VAR_DATA), address 1Bh
Bit
Bit Name
Default
15:0
VAR_DATA
0, RO
Description
Variance Data:
Two reads are required to return the full 32-bit Variance Sum value.
Following setting the VAR_FREEZE control, the first read of this
register will return the low 16 bits of the Variance data. A second
read will return the high 16 bits of Variance data.
74
www.national.com
DP83849ID
7.3.7 Variance Control Register (VAR_CTRL), Page 2, address 1Ah
This register contains the controls for the Link Quality Monitor function. The Link Quality Monitor provides a mechanism
for programming a set of thresholds for DSP parameters. If the thresholds are violated, an interrupt will be asserted if
enabled in the MISR. Monitor control and status are available in this register, while the LQDR register controls read/write
access to threshold values and current parameter values. Reading of LQMR register clears warning bits and re-arms the
interrupt generation. In addition, this register provides a mechanims for allowing automatic reset of the 100Mb link based
on the Link Quality Monitor status.
Table 51. Link Quality Monitor Register (LQMR), address 1Dh
Bit
Bit Name
Default
15
LQM_ENABLE
0, RW
Description
Link Quality Monitor Enable:
Enables the Link Quality Monitor. The enable is qualified by having
a valid 100Mb link. In addition, the individual thresholds can be disabled by setting to the max or min values.
14:10
RESERVED
0, RO
9
FC_HI_WARN
0, RO/COR
RESERVED: Writes ignored, read as 0.
Frequency Control High Warning:
This bit indicates the Frequency Control High Threshold was exceeded. This register bit will be cleared on read.
8
FC_LO_WARN
0, RO/COR
Frequency Control Low Warning:
This bit indicates the Frequency Control Low Threshold was exceeded. This register bit will be cleared on read.
7
FREQ_HI_WARN
0, RO/COR
Frequency Offset High Warning:
This bit indicates the Frequency Offset High Threshold was exceeded. This register bit will be cleared on read.
6
FREQ_LO_WARN
0, RO/COR
Frequency Offset Low Warning:
This bit indicates the Frequency Offset Low Threshold was exceeded. This register bit will be cleared on read.
5
DBLW_HI_WARN
0, RO/COR
DBLW High Warning:
This bit indicates the DBLW High Threshold was exceeded. This
register bit will be cleared on read.
4
DBLW_LO_WARN
0, RO/COR
DBLW Low Warning:
This bit indicates the DBLW Low Threshold was exceeded. This
register bit will be cleared on read.
3
DAGC_HI_WARN
0, RO/COR
DAGC High Warning:
This bit indicates the DAGC High Threshold was exceeded. This
register bit will be cleared on read.
2
DAGC_LO_WARN
0, RO/COR
DAGC Low Warning:
This bit indicates the DAGC Low Threshold was exceeded. This
register bit will be cleared on read.
1
C1_HI_WARN
0, RO/COR
C1 High Warning:
This bit indicates the DEQ C1 High Threshold was exceeded. This
register bit will be cleared on read.
0
C1_LO_WARN
0, RO/COR
C1 Low Warning:
This bit indicates the DEQ C1 Low Threshold was exceeded. This
register bit will be cleared on read.
75
www.national.com
DP83849ID
7.3.9 Link Quality Monitor Register (LQMR), Page 2, address 1Dh
This register provides read/write control of thresholds for the 100Mb Link Quality Monitor function. The register also provides a mechanism for reading current adapted parameter values. Threshold values may not be written if the device is
powered-down.
Table 52. Link Quality Data Register (LQDR), address 1Eh
Bit
Bit Name
Default
Description
15:14
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
13
SAMPLE_PARAM
0, RW
Sample DSP Parameter:
Setting this bit to a 1 enables reading of current parameter values
and initiates sampling of the parameter value. The parameter to be
read is selected by the LQ_PARAM_SEL bits.
12
WRITE_LQ_THR
0, RW
Write Link Quality Threshold:
Setting this bit will cause a write to the Threshold register selected
by LQ_PARAM_SEL and LQ_THR_SEL. The data written is contained in LQ_THR_DATA. This bit will always read back as 0.
11:9
LQ_PARAM_SEL
0, RW
Link Quality Parameter Select:
This 3-bit field selects the Link Quality Parameter. This field is used
for sampling current parameter values as well as for reads/writes to
Threshold values. The following encodings are available:
000: DEQ_C1
001: DAGC
010: DBLW
011: Frequency Offset
100: Frequency Control
8
LQ_THR_SEL
0, RW
Link Quality Threshold Select:
This bit selects the Link Quality Threshold to be read or written. A
0 selects the Low threshold, while a 1 selects the high threshold.
When combined with the LQ_PARAM_SEL field, the following encodings are available {LQ_PARAM_SEL, LQ_THR_SEL}:
000,0: DEQ_C1 Low
000,1: DEQ_C1 High
001,0: DAGC Low
001,1: DAGC High
010,0: DBLW Low
010,1: DBLW High
011,0: Frequency Offset Low
011,1: Frequency Offset High
100,0: Frequency Control Low
100,1: Frequency Control High
7:0
LQ_THR_DATA
0, RW
Link Quality Threshold Data:
The operation of this field is dependent on the value of the
Sample_Param bit.
If Sample_Param = 0:
On a write, this value contains the data to be written to the selected
Link Quality Threshold register.
On a read, this value contains the current data in the selected Link
Quality Threshold register.
If Sample_Param = 1:
On a read, this value contains the sampled parameter value. This
value will remain unchanged until a new read sequence is started.
76
www.national.com
DP83849ID
7.3.10 Link Quality Data Register (LQDR), Page 2
DP83849ID
8.0 Electrical Specifications
Note: All parameters are guaranteed by test, statistical analysis or design.
Recommended Operating Conditions
Absolute Maximum Ratings
Supply Voltage (VCC)
Supply voltage (VCC)
-0.5 V to 4.2 V
3.3 Volts + .3V
DC Input Voltage (VIN)
-0.5V to VCC + 0.5V
Industrial - Ambient Temperature (TA)
DC Output Voltage (VOUT)
-0.5V to VCC + 0.5V
Power Dissipation (PD)
Lead Temp. (TL)
(Soldering, 10 sec.)
260 °C
ESD Rating
(RZAP = 1.5k, CZAP = 100 pF)
4.0 kV
594 mW
Absolute maximum ratings are those values beyond which
the safety of the device cannot be guaranteed. They are
not meant to imply that the device should be operated at
these limits.
-65oC to 150°C
Storage Temperature (TSTG)
-40 to 85 °C
Thermal Characteristic
Maximum Case Temperature @ 1.0 W
Max
108
Units
°C
Theta Junction to Case (Tjc) @ 1.0 W
17.3
°C / W
53
°C / W
Theta Junction to Ambient (Tja) degrees Celsius/Watt - No Airflow @ 1.0 W
8.1 DC Specs
Symbol
Pin Types
Parameter
Conditions
Min
Typ
Max
2.0
Units
VIH
I
I/O
Input High Voltage Nominal VCC
V
VIL
I
I/O
Input Low Voltage
0.8
V
IIH
I
I/O
Input High Current VIN = VCC
10
µA
IIL
I
I/O
Input Low Current VIN = GND
10
µA
VOL
O,
I/O
Output Low
Voltage
IOL = 4 mA
0.4
V
VOH
O,
I/O
Output High
Voltage
IOH = -4 mA
IOZ
I/O,
O
TRI-STATE
Leakage
VOUT = VCC
Vcc - 0.5
µA
1.05
V
+2
%
PMD Output
Pair
100M Transmit
Voltage
VTPTDsym
PMD Output
Pair
100M Transmit
Voltage Symmetry
VTPTD_10
PMD Output
Pair
10M Transmit
Voltage
2.2
2.5
2.8
V
VFXTD_100
PMD Output
Pair
FX100M Transmit
Voltage
.3
.5
.93
V
I
CMOS Input
Capacitance
1
+ 10
VTPTD_100
CIN1
0.95
V
8
77
pF
www.national.com
Symbol
Pin Types
Parameter
Conditions
Min
CMOS Output
Capacitance
Typ
Max
8
Units
COUT1
O
pF
SDTHon
PMD Input
Pair
100BASE-TX
Signal detect turnon threshold
SDTHoff
PMD Input
Pair
100BASE-TX
Signal detect turnoff threshold
VTH1
PMD Input
Pair
10BASE-T Receive Threshold
Idd100
Supply
100BASE-TX
(Full Duplex)
180
mA
Idd10
Supply
10BASE-T
(Full Duplex)
180
mA
Idd
Supply
Power Down
Mode
9.5
mA
1000
200
mV diff pk-pk
585
CLK2MAC disabled
78
mV diff pk-pk
mV
www.national.com
DP83849ID
8.1 DC Specs (Continued)
DP83849ID
8.2 AC Specs
8.2.1 Power Up Timing
Vcc
X1 clock
T2.1.1
Hardware
RESET_N
32 clocks
MDC
T2.1.2
Latch-In of Hardware
Configuration Pins
T2.1.3
input
output
Dual Function Pins
Become Enabled As Outputs
Parameter
Description
Notes
Min
Typ
Max
Units
T2.1.1
Post Power Up Stabilization
MDIO is pulled high for 32-bit serial mantime prior to MDC preamble for agement initialization
register accesses
X1 Clock must be stable for a min. of
167ms at power up.
167
ms
T2.1.2
Hardware Configuration Latch- Hardware Configuration Pins are described in the Pin Description section
in Time from power up
167
ms
X1 Clock must be stable for a min. of
167ms at power up.
T2.1.3
Hardware Configuration pins
transition to output drivers
50
ns
Note: In RMII Mode, the minimum Post Power up Stabilization and Hardware Configuration Latch-in times are 84ms.
79
www.national.com
DP83849ID
8.2.2 Reset Timing
Vcc
X1 clock
T2.2.1
T2.2.4
Hardware
RESET_N
32 clocks
MDC
T2.2.2
Latch-In of Hardware
Configuration Pins
T2.2.3
input
output
Dual Function Pins
Become Enabled As Outputs
Parameter
Description
Notes
Min
Typ
Max
Units
T2.2.1
Post RESET Stabilization time MDIO is pulled high for 32-bit serial manprior to MDC preamble for reg- agement initialization
ister accesses
3
µs
T2.2.2
Hardware Configuration Latch- Hardware Configuration Pins are dein Time from the Deassertion scribed in the Pin Description section
of RESET (either soft or hard)
3
µs
T2.2.3
Hardware Configuration pins
transition to output drivers
50
ns
T2.2.4
RESET pulse width
X1 Clock must be stable for at min. of 1us
during RESET pulse low time.
1
µs
Note: It is important to choose pull-up and/or pull-down resistors for each of the hardware configuration pins that provide
fast RC time constants in order to latch-in the proper value prior to the pin transitioning to an output driver.
80
www.national.com
DP83849ID
8.2.3 MII Serial Management Timing
MDC
T2.3.1
T2.3.4
MDIO (output)
MDC
T2.3.2
Valid Data
MDIO (input)
Parameter
T2.3.3
Description
Notes
Min
T2.3.1
MDC to MDIO (Output) Delay Time
0
T2.3.2
MDIO (Input) to MDC Setup Time
10
T2.3.3
MDIO (Input) to MDC Hold Time
10
T2.3.4
MDC Frequency
Typ
Max
Units
30
ns
ns
ns
2.5
25
MHz
8.2.4 100 Mb/s MII Transmit Timing
T2.4.1
T2.4.1
TX_CLK
T2.4.3
T2.4.2
TXD[3:0]
TX_EN
Parameter
Valid Data
Min
Typ
T2.4.1
TX_CLK High/Low Time
Description
100 Mb/s Normal mode
Notes
16
20
T2.4.2
TXD[3:0], TX_EN Data Setup to TX_CLK
100 Mb/s Normal mode
10
ns
T2.4.3
TXD[3:0], TX_EN Data Hold from TX_CLK 100 Mb/s Normal mode
0
ns
81
Max Units
24
ns
www.national.com
DP83849ID
8.2.5 100 Mb/s MII Receive Timing
T2.5.1
T2.5.1
RX_CLK
T2.5.2
RXD[3:0]
RX_DV
RX_ER
Valid Data
Parameter
Description
Notes
Min
Typ
Max
Units
20
24
ns
30
ns
T2.5.1
RX_CLK High/Low Time
100 Mb/s Normal mode
16
T2.5.2
RX_CLK to RXD[3:0], RX_DV, RX_ER Delay 100 Mb/s Normal mode
10
Note: RX_CLK may be held low or high for a longer period of time during transition between reference and recovered
clocks. Minimum high and low times will not be violated.
8.2.6 100BASE-TX and 100BASE-FX MII Transmit Packet Latency Timing
TX_CLK
TX_EN
TXD
PMD Output Pair
Parameter
T2.6.1
T2.6.1
IDLE
(J/K)
Description
TX_CLK to PMD Output Pair
Latency
Notes
100BASE-TX and 100BASE-FX modes
DATA
Min
Typ
5
Max
Units
bits
Note: For Normal mode, latency is determined by measuring the time from the first rising edge of TX_CLK occurring after
the assertion of TX_EN to the first bit of the “J” code group as output from the PMD Output Pair. 1 bit time = 10 ns in 100
Mb/s mode.
82
www.national.com
DP83849ID
8.2.7 100BASE-TX and 100BASE-FX MII Transmit Packet Deassertion Timing
TX_CLK
TX_EN
TXD
T2.7.1
PMD Output Pair
Parameter
T2.7.1
DATA
DATA
(T/R)
(T/R)
Description
TX_CLK to PMD Output Pair
Deassertion
IDLE
IDLE
Notes
100BASE-TX and 100BASE-FX modes
Min
Typ
5
Max
Units
bits
Note: Deassertion is determined by measuring the time from the first rising edge of TX_CLK occurring after the deassertion of TX_EN to the first bit of the “T” code group as output from the PMD Output Pair. 1 bit time = 10 ns in 100 Mb/s mode.
83
www.national.com
DP83849ID
8.2.8 100BASE-TX Transmit Timing (tR/F & Jitter)
T2.8.1
+1 rise
90%
10%
PMD Output Pair
10%
+1 fall
90%
T2.8.1
-1 fall
-1 rise
T2.8.1
T2.8.1
T2.8.2
PMD Output Pair
eye pattern
Parameter
T2.8.1
T2.8.2
T2.8.2
Description
Notes
Min
Typ
Max
Units
3
4
5
ns
100 Mb/s tR and tF Mismatch
500
ps
100 Mb/s PMD Output Pair
Transmit Jitter
1.4
ns
100 Mb/s PMD Output Pair tR
and tF
Note: Normal Mismatch is the difference between the maximum and minimum of all rise and fall times
Note: Rise and fall times taken at 10% and 90% of the +1 or -1 amplitude
84
www.national.com
DP83849ID
8.2.9 100BASE-TX and 100BASE-FX MII Receive Packet Latency Timing
PMD Input Pair
IDLE
Data
(J/K)
T2.9.1
CRS
T2.9.2
RXD[3:0]
RX_DV
RX_ER
Parameter
Description
T2.9.1
Carrier Sense ON Delay
T2.9.2
Receive Data Latency
Notes
Min
Typ
100BASE-TX mode
20
100BASE-FX mode
10
100BASE-TX mode
24
100BASE-FX mode
14
Max
Units
bits
bits
Note: Carrier Sense On Delay is determined by measuring the time from the first bit of the “J” code group to the assertion
of Carrier Sense.
Note: 1 bit time = 10 ns in 100 Mb/s mode
Note: PMD Input Pair voltage amplitude is greater than the Signal Detect Turn-On Threshold Value.
8.2.10 100BASE-TX and 100BASE-FX MII Receive Packet Deassertion Timing
PMD Input Pair
DATA
IDLE
(T/R)
T2.10.1
CRS
Parameter
T2.10.1
Description
Carrier Sense OFF Delay
Notes
Min
Typ
100BASE-TX mode
24
100BASE-FX mode
14
Max
Units
bits
Note: Carrier Sense Off Delay is determined by measuring the time from the first bit of the “T” code group to the deassertion of Carrier Sense.
Note: 1 bit time = 10 ns in 100 Mb/s mode
85
www.national.com
DP83849ID
8.2.11 10 Mb/s MII Transmit Timing
T2.11.1
T2.11.1
TX_CLK
T2.11.3
T2.11.2
TXD[3:0]
TX_EN
Parameter
Valid Data
Description
Notes
Min
Typ
Max Units
200
210
T2.11.1
TX_CLK High/Low Time
10 Mb/s MII mode
190
ns
T2.11.2
TXD[3:0], TX_EN Data Setup to TX_CLK fall
10 Mb/s MII mode
25
ns
T2.11.3
TXD[3:0], TX_EN Data Hold from TX_CLK rise
10 Mb/s MII mode
0
ns
Note: An attached Mac should drive the transmit signals using the positive edge of TX_CLK. As shown above, the MII
signals are sampled on the falling edge of TX_CLK.
8.2.12 10 Mb/s MII Receive Timing
T2.12.1
T2.12.1
RX_CLK
T2.12.3
T2.12.2
RXD[3:0]
RX_DV
Parameter
Valid Data
Description
Notes
Min
Typ
Max
Units
160
200
240
ns
T2.12.1
RX_CLK High/Low Time
T2.12.2
RX_CLK to RXD[3:0], RX_DV Delay
10 Mb/s MII mode
100
ns
T2.12.3
RX_CLK rising edge delay from RXD[3:0],
RX_DV Valid
10 Mb/s MII mode
100
ns
Note: RX_CLK may be held low for a longer period of time during transition between reference and recovered clocks.
Minimum high and low times will not be violated.
86
www.national.com
DP83849ID
8.2.13 10 Mb/s Serial Mode Transmit Timing
T2.13.2
T2.13.1
TX_CLK
T2.13.4
T2.13.3
TXD[0]
TX_EN
Parameter
Valid Data
Min
Typ
T2.13.1
TX_CLK High Time
Description
10 Mb/s Serial mode
Notes
20
25
Max Units
30
ns
T2.13.2
TX_CLK Low Time
10 Mb/s Serial mode
70
75
80
ns
T2.13.3
TXD_0, TX_EN Data Setup to TX_CLK rise
10 Mb/s Serial mode
25
ns
T2.13.4
TXD_0, TX_EN Data Hold from TX_CLK rise
10 Mb/s Serial mode
0
ns
8.2.14 10 Mb/s Serial Mode Receive Timing
T2.14.1
T2.14.1
RX_CLK
T2.14.2
RXD[0]
RX_DV
Parameter
Valid Data
Description
T2.14.1
RX_CLK High/Low Time
T2.14.2
RX_CLK fall to RXD_0, RX_DV Delay
Notes
10 Mb/s Serial mode
Min
Typ
Max
Units
35
50
65
ns
10
ns
-10
Note: RX_CLK may be held high for a longer period of time during transition between reference and recovered clocks.
Minimum high and low times will not be violated.
87
www.national.com
DP83849ID
8.2.15 10BASE-T Transmit Timing (Start of Packet)
TX_CLK
TX_EN
TXD
T2.15.2
PMD Output Pair
T2.15.1
Parameter
T2.15.1
Description
Notes
Transmit Output Delay from the
Min
Typ
Max
Units
10 Mb/s MII mode
3.5
bits
10 Mb/s Serial mode
3.5
bits
Falling Edge of TX_CLK
T2.15.2
Transmit Output Delay from the
Rising Edge of TX_CLK
Note: 1 bit time = 100 ns in 10Mb/s.
8.2.16 10BASE-T Transmit Timing (End of Packet)
TX_CLK
TX_EN
0
PMD Output Pair
T2.16.1
0
T2.16.2
PMD Output Pair
Parameter
T2.16.1
1
1
Description
Notes
End of Packet High Time
Min
Typ
250
300
Max
Units
ns
250
300
ns
(with ‘0’ ending bit)
T2.16.2
End of Packet High Time
(with ‘1’ ending bit)
88
www.national.com
DP83849ID
8.2.17 10BASE-T Receive Timing (Start of Packet)
1st SFD bit decoded
1
0
1
0
1
0
1
0
1
0
1
1
TPRD±
T2.17.1
CRS
RX_CLK
T2.17.2
RX_DV
T2.17.3
0000
RXD[3:0]
Parameter
Preamble
Description
SFD
Notes
Min
Data
Typ
Max
Units
1000
ns
T2.17.1
Carrier Sense Turn On Delay (PMD
Input Pair to CRS)
630
T2.17.2
RX_DV Latency
10
bits
T2.17.3
Receive Data Latency
8
bits
Measurement shown from SFD
Note: 10BASE-T RX_DV Latency is measured from first bit of preamble on the wire to the assertion of RX_DV
Note: 1 bit time = 100 ns in 10 Mb/s mode.
8.2.18 10BASE-T Receive Timing (End of Packet)
1
0
1
IDLE
PMD Input Pair
RX_CLK
T2.18.1
CRS
Parameter
T2.18.1
Description
Notes
Carrier Sense Turn Off Delay
89
Min
Typ
Max
Units
1.0
µs
www.national.com
DP83849ID
8.2.19 10 Mb/s Heartbeat Timing
TX_EN
TX_CLK
T2.19.2
T2.19.1
COL
Parameter
Description
Notes
Min
Typ
Max
Units
T2.19.1
CD Heartbeat Delay
10 Mb/s half-duplex mode
1200
ns
T2.19.2
CD Heartbeat Duration
10 Mb/s half-duplex mode
1000
ns
8.2.20 10 Mb/s Jabber Timing
TXE
T2.20.1
T2.20.2
PMD Output Pair
COL
Parameter
Description
Notes
Min
Typ
Max
Units
T2.20.1
Jabber Activation Time
85
ms
T2.20.2
Jabber Deactivation Time
500
ms
90
www.national.com
DP83849ID
8.2.21 10BASE-T Normal Link Pulse Timing
T2.21.2
T2.21.1
Normal Link Pulse(s)
Parameter
Description
Notes
Min
Typ
Max
Units
T2.21.1
Pulse Width
100
ns
T2.21.2
Pulse Period
16
ms
Note: These specifications represent transmit timings.
8.2.22 Auto-Negotiation Fast Link Pulse (FLP) Timing
T2.22.2
T2.22.3
T2.22.1
T2.22.1
Fast Link Pulse(s)
clock
pulse
data
pulse
clock
pulse
T2.22.5
T2.22.4
FLP Burst
Parameter
FLP Burst
Description
Notes
Min
Typ
Max
Units
T2.22.1
Clock, Data Pulse Width
100
ns
T2.22.2
Clock Pulse to Clock Pulse
Period
125
µs
T2.22.3
Clock Pulse to Data Pulse
Period
62
µs
T2.22.4
Burst Width
2
ms
T2.22.5
FLP Burst to FLP Burst Period
16
ms
Data = 1
Note: These specifications represent transmit timings.
91
www.national.com
DP83849ID
8.2.23 100BASE-TX Signal Detect Timing
PMD Input Pair
T2.23.1
T2.23.2
SD+ internal
Parameter
Description
Notes
Min
Typ
Max
Units
T2.23.1
SD Internal Turn-on Time
1
ms
T2.23.2
SD Internal Turn-off Time
350
µs
Max
Units
240
ns
Note: The signal amplitude on PMD Input Pair must be TP-PMD compliant.
8.2.24 100 Mb/s Internal Loopback Timing
TX_CLK
TX_EN
TXD[3:0]
CRS
T2.24.1
RX_CLK
RX_DV
RXD[3:0]
Parameter
T2.24.1
Description
TX_EN to RX_DV Loopback
Notes
Min
100 Mb/s internal loopback mode
Typ
Note1: Due to the nature of the descrambler function, all 100BASE-TX Loopback modes will cause an initial “dead-time”
of up to 550 µs during which time no data will be present at the receive MII outputs. The 100BASE-TX timing specified is
based on device delays after the initial 550µs “dead-time”.
Note2: Measurement is made from the first rising edge of TX_CLK after assertion of TX_EN.
92
www.national.com
DP83849ID
8.2.25 10 Mb/s Internal Loopback Timing
TX_CLK
TX_EN
TXD[3:0]
CRS
T2.25.1
RX_CLK
RX_DV
RXD[3:0]
Parameter
T2.25.1
Description
TX_EN to RX_DV Loopback
Notes
Min
10 Mb/s internal loopback mode
Typ
Max
Units
2
µs
Note: Measurement is made from the first rising edge of TX_CLK after assertion of TX_EN.
93
www.national.com
DP83849ID
8.2.26 RMII Transmit Timing
T2.26.1
X1
T2.26.2
TXD[1:0]
TX_EN
T2.26.3
Valid Data
T2.26.4
PMD Output Pair
Parameter
Symbol
Description
Notes
Min
50 MHz Reference Clock
Typ
T2.26.1
X1 Clock Period
T2.26.2
TXD[1:0], TX_EN, Data Setup
to X1 rising
4
ns
T2.26.3
TXD[1:0], TX_EN, Data Hold
from X1 rising
2
ns
T2.26.4
X1 Clock to PMD Output Pair 100BASE-TX or 100BASE-FX
Latency (100Mb)
94
20
Max Units
11
ns
bits
www.national.com
DP83849ID
8.2.27 RMII Receive Timing
PMD Input Pair
IDLE
Data
(J/K)
Data
(TR)
T2.27.4
T2.27.5
X1
T2.27.1
T2.27.2
T2.27.3
T2.27.2
T2.27.2
RX_DV
CRS_DV
T2.27.2
RXD[1:0]
RX_ER
Parameter
Description
T2.27.1
X1 Clock Period
T2.27.2
RXD[1:0], CRS_DV, RX_DV
and RX_ER output delay from
X1 rising
T2.27.3
CRS ON delay (100Mb)
T2.27.4
CRS OFF delay (100Mb)
T2.27.5
RXD[1:0] and RX_ER latency
(100Mb)
Notes
Min
50 MHz Reference Clock
Typ
Max
20
2
ns
14
100BASE-TX mode
18.5
100BASE-FX mode
9
100BASE-TX mode
27
100BASE-FX mode
17
100BASE-TX mode
38
100BASE-FX mode
27
Units
ns
bits
bits
bits
Note: Per the RMII Specification, output delays assume a 25pF load.
Note: CRS_DV is asserted asynchronously in order to minimize latency of control signals through the Phy. CRS_DV may
toggle synchronously at the end of the packet to indicate CRS deassertion.
Note: RX_DV is synchronous to X1. While not part of the RMII specification, this signal is provided to simplify recovery of
receive data.
Note: CRS ON delay is measured from the first bit of the JK symbol on the PMD Receive Pair to initial assertion of
CRS_DV.
Note: CRS_OFF delay is measured from the first bit of the TR symbol on the PMD Receive Pair to initial deassertion of
CRS_DV.
Note: Receive Latency is measured from the first bit of the symbol pair on the PMD Receive Pair. Typical values are with
the Elasticity Buffer set to the default value (01).
95
www.national.com
DP83849ID
8.2.28 Isolation Timing
Clear bit 10 of BMCR
(return to normal operation
from Isolate mode)
T2.28.1
MODE
NORMAL
ISOLATE
Parameter
T2.28.1
Description
Notes
Min
Typ
From software clear of bit 10 in
the BMCR register to the transition from Isolate to Normal Mode
Max
Units
100
µs
Max
Units
8.2.29 CLK2MAC Timing
X1
T2.29.2
T2.29.1
T2.29.1
CLK2MAC
Parameter
T2.29.1
T2.29.2
Description
Notes
CLK2MAC High/Low Time
CLK2MAC propagation delay
Min
Typ
MII mode
20
ns
RMII mode
10
ns
Relative to X1
8
ns
Note: CLK2MAC characteristics are dependent upon the X1 input characteristics.
96
www.national.com
DP83849ID
Notes:
97
www.national.com
DP83849ID PHYTER® DUAL Industrial Temperature with Fiber Support (FX)
Dual Port 10/100 Mb/s Ethernet Physical Layer Transceiver
9.0 Physical Dimensions
inches (millimeters) unless otherwise noted
Thin Quad Flat Package (TQFP)
NS Package Number VHB80A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or systems which,
(a) are intended for surgical implant into the body, or (b) support
or sustain life, and whose failure to perform, when properly used
in accordance with instructions for use provided in the labeling,
can be reasonably expected to result in a significant injury to the
user.
2. A critical component is any component of a life support device
or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship
Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no “Banned
Substances” as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Corporation
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
National Semiconductor
Europe
Fax:
+49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel:
+49 (0) 69 9508 6208
English Tel:
+44 (0) 870 24 0 2171
Francais Tel:
+33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific
Customer Response Group
Tel: 65-254-4466
Fax: 65-250-4466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.