ADC12D040 Dual 12-Bit, 40 MSPS, 600 mW A/D Converter with Internal/External Reference General Description Features The ADC12D040 is a dual, low power monolithic CMOS analog-to-digital converter capable of converting analog input signals into 12-bit digital words at 40 Megasamples per second (Msps), minimum. This converter uses a differential, pipeline architecture with digital error correction and an onchip sample-and-hold circuit to minimize die size and power consumption while providing excellent dynamic performance. Operating on a single 5V power supply, the ADC12D040 achieves 10.9 effective bits at 10 MHz input and consumes just 600 mW at 40 Msps, including the reference current. The Power Down feature reduces power consumption to 75 mW. The differential inputs provide a full scale differential input swing equal to 2VREF with the possibility of a single-ended input. Full use of the differential input is recommended for optimum performance. The digital outputs for the two ADCs are available on separate 12-bit buses with an output data format choice of offset binary or 2’s complement. For ease of interface, the digital output driver power pins of the ADC12D040 can be connected to a separate supply voltage in the range of 2.4V to the digital supply voltage, making the outputs compatible with low voltage systems. The ADC12D040’s speed, resolution and single supply operation make it well suited for a variety of applications. This device is available in the 64-lead TQFP package and will operate over the industrial temperature range of −40˚C to +85˚C. An evaluation board is available to facilitate the product evaluation process n n n n n n n Binary or 2’s complement output format Single supply operation Internal sample-and-hold Outputs 2.4V to 5V compatible Power down mode Pin-compatible with ADC12DL066 Internal/External Reference Key Specifications n n n n n n SNR (fIN = 10 MHz) ENOB (fIN = 10 MHz) SFDR (fIN = 10 MHz) Data Latency Supply Voltage Power Consumption, Operating — Operating — Power Down Mode 68 dB (typ) 10.9 bits (typ) 80 dB (typ) 6 Clock Cycles +5V ± 5% 600 mW (typ) 75 mW (typ) Applications n n n n n n Ultrasound and Imaging Instrumentation Communications Receivers Sonar/Radar xDSL Cable Modems Connection Diagram 20046001 TRI-STATE ® is a registered trademark of National Semiconductor Corporation. © 2005 National Semiconductor Corporation DS200460 www.national.com ADC12D040 Dual 12-Bit, 40 MSPS, 600 mW A/D Converter with Internal/External Reference December 2005 ADC12D040 Ordering Information Industrial (−40˚C ≤ TA ≤ +85˚C) Package ADC12D040CIVS 64 Pin TQFP ADC12D040CIVSX 64 Pin TQFP Tape and Reel ADC12D040EVAL Evaluation Board Block Diagram 20046002 www.national.com 2 ADC12D040 Pin Descriptions and Equivalent Circuits Pin No. Symbol Equivalent Circuit Description ANALOG I/O VINA+ VINB+ Non-Inverting analog signal Inputs. With a 2.0V reference the full-scale input signal level is 2.0 VP-P on each pin of the input pair, centered on a common VCM. VINA− VINB− Inverting analog signal Input. With a 2.0V reference the full-scale input signal level is 2.0 VP-P on each pin of the input pair, centered on a common VCM. These (-) input pins may be connected to a common VCM for single-ended operation, but a differential input signal is required for best performance. 7 VREF Reference input. This pin should be bypassed to AGND with a 0.1 µF monolithic capacitor when external reference is used. VREF is 2.0V nominal and should be between 1.0V to 2.4V. 11 INT/EXT REF 13 5 VRPA VRPB 14 4 VRMA VRMB 12 6 VRNA VRNB 15 2 16 1 VREF select pin. With a logic low at this pin the internal 2.0V reference is selected. With a logic high on this pin an external reference voltage must be applied to VREF input pin 7. These pins are high impedance reference bypass pins only. Connect a 0.1 µF capacitor from each of these pins to AGND. DO NOT LOAD these pins. DIGITAL I/O 60 CLK Digital clock input. The range of frequencies for this input is 100 kHz to 55 MHz (typical) with guaranteed performance at 40 MHz. The input is sampled on the rising edge of this input. 22 41 OEA OEB OEA and OEB are the output enable pins that, when low, enables their respective TRI-STATE ® data output pins. When either of these pins is high, the corresponding outputs are in a high impedance state. 59 PD PD is the Power Down input pin. When high, this input puts the converter into the power down mode. When this pin is low, the converter is in the active mode. 21 OF Output Format pin. A logic low on this pin causes output data to be in offset binary format. A logic high on this pin causes the output data to be in 2’s complement format. 3 www.national.com ADC12D040 Pin Descriptions and Equivalent Circuits Pin No. Symbol 24–29 34–39 DA0–DA11 Equivalent Circuit (Continued) Description Digital data output pins that make up the 12-bit conversion results of their respective converters. DA0 and DB0 are the LSBs, while DA11 and DB11 are the MSBs of the output word. Output levels are TTL/CMOS compatible. 42–47 52–57 DB0–DB11 ANALOG POWER 9, 18, 19, 62, 63 VA 3, 8, 10, 17, 20, 61, 64 AGND Positive analog supply pins. These pins should be connected to a quiet +5V source and bypassed to AGND with 0.1 µF monolithic capacitors located within 1 cm of these power pins, and with a 10 µF capacitor. The ground return for the analog supply. DIGITAL POWER 33, 48 VD 32, 49 DGND 30, 51 23, 31, 40, 50, 58 www.national.com Positive digital supply pin. This pin should be connected to the same quiet +5V source as is VA and be bypassed to DGND with a 0.1 µF monolithic capacitor located within 1 cm of the power pin and with a 10 µF capacitor. The ground return for the digital supply. VDR Positive digital supply pins for the ADC12D040’s output drivers. These pins should be connected to a voltage source of +2.4V to +5V and bypassed to DR GND with a 0.1 µF monolithic capacitor. If the supply for these pins are different from the supply used for VA and VD, they should also be bypassed with a 10 µF tantalum capacitor. VDR should never exceed the voltage on VD. All bypass capacitors should be located within 1 cm of the supply pin. DR GND The ground return for the digital supply for the ADC12D040’s output drivers. These pins should be connected to the system digital ground, but not be connected in close proximity to the ADC12D040’s DGND or AGND pins. See Section 5 (Layout and Grounding) for more details. 4 Operating Ratings (Notes 1, 2) (Notes 1, 2) Operating Temperature If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VA, VD) VA, VD, VDR VDR VD + 0.3V ≤ 100 mV Voltage on Any Input or Output Pin Package Dissipation at TA = 25˚C 1.0V to 2.4V CLK, PD, OE −0.5V to (VD + 0.5V) Analog Input Pins −0V to (VA − 0.5V) Input Common Mode Voltage (VCM) VREF/2 to VA − VREF ≤100mV |AGND–DGND| ± 25 mA ± 50 mA Package Input Current (Note 3) +2.35V to VD VREF Input −0.3V to (VA or VD +0.3V) Input Current at Any Pin (Note 3) +4.75V to +5.25V Output Driver Supply (VDR) 6.5V |VA–VD| −40˚C ≤ TA ≤ +85˚C See (Note 4) Package Thermal Resistance ESD Susceptibility Human Body Model (Note 5) Machine Model (Note 5) Soldering Temperature, Infrared, 10 sec. (Note 6) Storage Temperature 2500V Package θJ-A 250V 64-Lead TQFP 50˚C / W 235˚C −65˚C to +150˚C Converter Electrical Characteristics Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA VD +5V, VDR +3.0V, PD = 0V, INT/EXT = VD, VREF = +2.0V, OEA, OEB = 0V, fCLK = 40 MHz, tr = tf = 3 ns, CL = 20 pF/pin. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25˚C (Notes 7, 8, 9) Symbol Parameter Typical (Note 10) Limits (Note 10) 12 Bits (min) ± 0.7 ± 0.4 ± 2.0 ± 1.0 LSB (max) Positive Error 0.51 +2.8/−1.9 %FS Negative Error 0.68 +4/−2.7 Conditions Units (Limits) STATIC CONVERTER CHARACTERISTICS Resolution with No Missing Codes INL Integral Non Linearity (Note 11) DNL Differential Non Linearity GE Gain Error TC GE Gain Error Tempco VOFF Offset Error (VIN+ = VIN−) TC VOFF Offset Error Tempco LSB (max) %FS External Reference 15 ppm/oC Internal Reference 100 ppm/oC −0.1 ± 1.2 %FS (max) External Reference 3 ppm/oC Internal Reference 3 ppm/oC Under Range Output Code 0 0 Over Range Output Code 4095 4095 DYNAMIC CONVERTER CHARACTERISTICS FPBW Full Power Bandwidth SNR Signal-to-Noise Ratio SINAD Signal-to-Noise and Distortion ENOB Effective Number of Bits THD Total Harmonic Distortion H2 Second Harmonic 0 dBFS Input, Output at −3 dB 100 fIN = 1 MHz, VIN = −0.5 dBFS 69 fIN = 10 MHz, VIN = −0.5 dBFS 68 fIN = 1 MHz, VIN = −0.5 dBFS 69 fIN = 10 MHz, VIN = −0.5 dBFS 68 fIN = 1 MHz, VIN = −0.5 dBFS 11.1 fIN = 10 MHz, VIN = −0.5 dBFS 10.9 fIN = 1 MHz, VIN = −0.5 dBFS −80 fIN = 10 MHz, VIN = −0.5 dBFS −78 fIN = 1 MHz, VIN = −0.5 dBFS −84 fIN = 10 MHz, VIN = −0.5 dBFS −80 5 MHz dB 66.5 dB (min) dB 65.6 dB (min) 10.6 Bits (min) Bits dB −69 dB (max) −73 dB (max) dB www.national.com ADC12D040 Absolute Maximum Ratings ADC12D040 Converter Electrical Characteristics (Continued) Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA VD +5V, VDR +3.0V, PD = 0V, INT/EXT = VD, VREF = +2.0V, OEA, OEB = 0V, fCLK = 40 MHz, tr = tf = 3 ns, CL = 20 pF/pin. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25˚C (Notes 7, 8, 9) Symbol H3 Parameter Typical (Note 10) Conditions Limits (Note 10) Units (Limits) fIN = 1 MHz, VIN = −0.5 dBFS −84 fIN = 10 MHz, VIN = −0.5 dBFS −82 fIN = 1 MHz, VIN = −0.5 dBFS 84 fIN = 10 MHz, VIN = −0.5 dBFS 80 fIN = 9.6 MHz and 10.2 MHz, each = −6.0 dBFS −80 dBFS Channel — Channel Offset Match ± 0.02 %FS Channel — Channel Gain Error Match ± 0.05 %FS −80 dB (CLK LOW) 8 pF (CLK HIGH) 7 Third Harmonic SFDR Spurious Free Dynamic Range IMD Intermodulation Distortion dB −69.5 dB (max) 69.5 dB (min) dB INTER-CHANNEL CHARACTERISTICS 10 MHz Tested Channel. 15 MHz Other Channel Crosstalk REFERENCE AND ANALOG INPUT CHARACTERISTICS CIN VIN Input Capacitance (each pin to GND) VIN = 2.5 Vdc + 0.7 Vrms VREF Input Reference Voltage (Note 13) 2.00 RREF Reference Input Resistance 100 VIN Analog Input Voltage Range pF 1.0 2.4 V (min) V (max) MΩ (min) 0 V (min) 4 V (max) DC and Logic Electrical Characteristics Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +5V, VDR = +3.0V, PD = 0V, INT/EXT = VD, VREF = +2.0V, OEA, OEB = 0V, fCLK = 40 MHz, tr = tf = 3 ns, CL = 20 pF/pin. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25˚C (Notes 7, 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits (Note 10) Units (Limits) CLK, PD, OE DIGITAL INPUT CHARACTERISTICS VIN(1) Logical “1” Input Voltage VD = 5.25V 2.0 V (min) VIN(0) Logical “0” Input Voltage VD = 4.75V 1.0 V (max) IIN(1) Logical “1” Input Current VIN = 5.0V 10 µA IIN(0) Logical “0” Input Current VIN = 0V −10 µA CIN Digital Input Capacitance 5 pF D0–D11 DIGITAL OUTPUT CHARACTERISTICS VOUT(1) Logical “1” Output Voltage IOUT = −0.5 mA VOUT(0) Logical “0” Output Voltage IOUT = 1.6 mA, VDR = 3V IOZ TRI-STATE Output Current +ISC VDR = 2.5V 2.3 VDR = 3V 2.7 V (min) V (min) 0.4 V (max) VOUT = 2.5V or 5V 100 nA VOUT = 0V −100 nA Output Short Circuit Source Current VOUT = 0V −20 mA −ISC Output Short Circuit Sink Current VOUT = VDR 20 mA COUT Digital Output Capacitance 5 pF www.national.com 6 (Continued) Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +5V, VDR = +3.0V, PD = 0V, INT/EXT = VD, VREF = +2.0V, OEA, OEB = 0V, fCLK = 40 MHz, tr = tf = 3 ns, CL = 20 pF/pin. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25˚C (Notes 7, 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits (Note 10) Units (Limits) POWER SUPPLY CHARACTERISTICS IA Analog Supply Current PD Pin = DGND, VREF = 2.0V PD Pin = VDR 93 15 110 mA (max) mA ID Digital Supply Current PD Pin = DGND PD Pin = VDR 16 0 18 mA (max) mA IDR Digital Output Supply Current PD Pin = DGND, CL = 0 pF (Note 14) PD Pin = VDR 10.5 0 12 mA (max) mA Total Power Consumption PD Pin = DGND, CL = 0 pF (Note 15) PD Pin = VDR 600 75 700 mW mW Power Supply Rejection Rejection of Full-Scale Error with VA = 4.75V vs. 5.25V 56 PSRR1 dB AC Electrical Characteristics Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +5V, VDR = +3.0V, PD = 0V, INT/EXT = VD, VREF = +2.0V, OEA, OEB = 0V, fCLK = 40 MHz, tr = tf = 3 ns, CL = 20 pF/pin. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25˚C (Notes 7, 8, 9, 12) Symbol Parameter Conditions Typical (Note 10) Limits (Note 10) Units (Limits) 40 MHz (min) fCLK1 Maximum Clock Frequency fCLK2 Minimum Clock Frequency 100 kHz tCH Clock High Time 9 ns tCL Clock Low Time 9 ns tCONV Conversion Latency tOD Data Output Delay after Rising CLK Edge tAD Aperture Delay 1.2 ns tAJ Aperture Jitter 2 ps rms tHOLD Clock Edge to Data Transition 8 ns tDIS Data outputs into TRI-STATE Mode 4 ns tEN Data Outputs Active after TRI-STATE 4 ns tPD Power Down Mode Exit Cycle 500 ns VDR = 3.0V 10 6 Clock Cycles 17.5 ns (max) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: All voltages are measured with respect to GND = AGND = DGND DR GND = 0V, unless otherwise specified. Note 3: When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND, or VIN > VA), the current at that pin should be limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to two. Note 4: The absolute maximum junction temperature (TJmax) for this device is 150˚C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature, (TA), and can be calculated using the formula PDMAX = (TJmax - TA )/θJA. The values for maximum power dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided. Note 5: Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through 0Ω. Note 6: The 235˚C reflow temperature refers to infrared reflow. For Vapor Phase Reflow (VPR), the following Conditions apply: Maintain the temperature at the top of the package body above 183˚C for a minimum 60 seconds. The temperature measured on the package body must not exceed 220˚C. Only one excursion above 183˚C is allowed per reflow cycle. Note 7: The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided current is limited per (Note 3). However, errors in the A/D conversion can occur if the input goes above VA or below GND by more than 100 mV. As an example, if VA is 4.75V, the full-scale input voltage must be ≤4.85V to ensure accurate conversions. 7 www.national.com ADC12D040 DC and Logic Electrical Characteristics ADC12D040 AC Electrical Characteristics (Continued) 20046007 Note 8: To guarantee accuracy, it is required that |VA–VD| ≤ 100 mV and separate bypass capacitors are used at each power supply pin. Note 9: With the test condition for VREF = +2.0V (4VP-P differential input), the 12-bit LSB is 977 µV. Note 10: Typical figures are at TA = TJ = 25˚C, and represent most likely parametric norms. Test limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 11: Integral Non Linearity is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes through positive and negative full-scale. Note 12: Timing specifications are tested at TTL logic levels, VIL = 0.4V for a falling edge and VIH = 2.4V for a rising edge. Note 13: Optimum performance will be obtained by keeping the reference input in the 1.8V to 2.4V range. The LM4051CIM3-ADJ (SOT23 package) is recommended for this application. Note 14: IDR is the current consumed by the switching of the output drivers and is primarily determined by load capacitance on the output pins, the supply voltage, VDR, and the rate at which the outputs are switching (which is signal dependent). IDR=VDR(C0 x f0 + C1 x f1 +....C11 x f11) where VDR is the output driver power supply voltage, Cn is total capacitance on the output pin, and fn is the average frequency at which that pin is toggling. Note 15: Excludes IDR. See note 14. www.national.com 8 APERTURE DELAY is the time after the rising edge of the clock to when the input signal is acquired or held for conversion. OUTPUT DELAY is the time delay after the rising edge of the clock before the data update is presented at the output pins. APERTURE JITTER (APERTURE UNCERTAINTY) is the variation in aperture delay from sample to sample. Aperture jitter manifests itself as noise in the output. OVER RANGE RECOVERY TIME is the time required after VIN goes from a specified voltage out of the normal input range to a specified voltage within the normal input range and the converter makes a conversion with its rated accuracy. PIPELINE DELAY (LATENCY) is the number of clock cycles between initiation of conversion and when that data is presented to the output driver stage. Data for any given sample is available at the output pins the Pipeline Delay plus the Output Delay after the sample is taken. New data is available at every clock cycle, but the data lags the conversion by the pipeline delay. POSITIVE FULL SCALE ERROR is the difference between the actual last code transition and its ideal value of 11⁄2 LSB below positive full scale. CLOCK DUTY CYCLE is the ratio of the time during one cycle that a repetitive digital waveform is high to the total time of one period. The specification here refers to the ADC clock input signal. COMMON MODE VOLTAGE (VCM) is the d.c. potential present at both signal inputs to the ADC. CONVERSION LATENCY See PIPELINE DELAY. CROSSTALK is coupling of energy from one channel into the other channel. DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated as: Gain Error = Positive Full Scale Error − Negative FullScale Error Gain Error can also be separated into Positive Gain Error and Negative Gain Error, which are. POWER SUPPLY REJECTION RATIO (PSRR) is a measure of how well the ADC rejects a change in the power supply voltage. For the ADC12D040, PSRR1 is the ratio of the change in Full-Scale Error that results from a change in the d.c. power supply voltage, expressed in dB. PSRR2 is a measure of how well an a.c. signal riding upon the power supply is rejected at the output. SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms value of the sum of all other spectral components below one-half the sampling frequency, not including harmonics or d.c. SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the input signal to the rms value of all of the other spectral components below half the clock frequency, including harmonics but excluding d.c. SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the input signal and the peak spurious signal, where a spurious signal is any signal present in the output spectrum that is not present at the input. TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB, of the rms total of the first seven harmonic levels at the output to the level of the fundamental at the output. THD is calculated as PGE = Positive Full-Scale Error − Offset Error NGE = Offset Error − Negative Full-Scale Error GAIN ERROR MATCHING is the difference in gain errors between the two converters divided by the average gain of the converters. INTEGRAL NON LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from negative full scale (1⁄2 LSB below the first code transition) through positive full scale (1⁄2 LSB above the last code transition). The deviation of any given code from this straight line is measured from the center of that code value. INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in the intermodulation products to the total power in the original frequencies. IMD is usually expressed in dBFS. LSB (LEAST SIGNIFICANT BIT) is the bit that has the smallest value or weight of all bits. This value is VREF / 2n, where “n” is the ADC resolution in bits, which is 12 in the case of the ADC12D040. MISSING CODES are those output codes that will never appear at the ADC outputs. The ADC12D040 is guaranteed not to have any missing codes. MSB (MOST SIGNIFICANT BIT) is the bit that has the largest value or weight. Its value is one half of full scale. NEGATIVE FULL SCALE ERROR is the difference between the actual first code transition and its ideal value of 1⁄2 LSB above negative full scale. where f1 is the RMS power of the fundamental (output) frequency and f2 through f10 are the RMS power of the first 9 harmonic frequencies in the output spectrum. – Second Harmonic Distortion (2ND HARM) is the difference expressed in dB, between the RMS power in the input frequency at the output and the power in its 2nd harmonic level at the output. – Third Harmonic Distortion (3RD HARM) is the difference, expressed in dB, between the RMS power in the input frequency at the output and the power in its 3rd harmonic level at the output. 9 www.national.com ADC12D040 OFFSET ERROR is the difference between the two input voltages (VIN+ –VIN−) required to cause a transition from code 2047 to 2048. Specification Definitions ADC12D040 Timing Diagram 20046009 Output Timing Transfer Characteristic 20046010 FIGURE 1. Transfer Characteristic www.national.com 10 VA = VD = 5V, VDR = 3V, fCLK = 40 MHz, fIN = 10 MHz unless DNL INL 20046036 20046037 INL & DNL vs. Supply Voltage DNL & INL vs. Clock Frequency 20046038 20046044 DNL & INL vs. Clock Duty Cycle DNL & INL vs. Reference Voltage 20046047 20046050 11 www.national.com ADC12D040 Typical Performance Characteristics otherwise stated ADC12D040 Typical Performance Characteristics VA = VD = 5V, VDR = 3V, fCLK = 40 MHz, fIN = 10 MHz unless otherwise stated (Continued) INL & DNL vs. Temperature SNR, SINAD, SFDR vs. Supply Voltage 20046039 20046040 SNR, SINAD, SFDR vs. Clock Frequency SNR, SINAD, SFDR vs. Clock Duty Cycle 20046048 20046045 SNR, SINAD, SFDR vs. Input Frequency SNR, SINAD, SFDR vs. Reference Voltage 20046042 www.national.com 20046051 12 SNR, SINAD, SFDR vs. Temperature Distortion vs. Supply Voltage 20046058 20046041 Distortion vs. Clock Frequency Distortion vs. Clock Duty Cycle 20046049 20046046 Distortion vs. Input Frequency Distortion vs. Reference Voltage 20046043 20046052 13 www.national.com ADC12D040 Typical Performance Characteristics VA = VD = 5V, VDR = 3V, fCLK = 40 MHz, fIN = 10 MHz unless otherwise stated (Continued) ADC12D040 Typical Performance Characteristics VA = VD = 5V, VDR = 3V, fCLK = 40 MHz, fIN = 10 MHz unless otherwise stated (Continued) Distortion vs. Temperature Power Consumption vs. Reference Voltage 20046059 20046053 Spectral Response @ Fin = 9.95 MHz, FCLK = 40 MHz Power Consumption vs. Temperature 20046055 20046054 Crosstalk Response Fin = 9.95 MHz, FCROSSTALK = 15 MHz, FCLK = 40 MHz IMD Response Fin = 9.6 MHz, 10.2 MHz, FCLK = 40 MHz 20046056 20046057 www.national.com 14 Operating on a single +5V supply, the ADC12D040 uses a pipeline architecture and has error correction circuitry to help ensure maximum performance. The differential analog input signal is digitized to 12 bits and the reference input is buffered to ease the task of driving that pin. The output word rate is the same as the clock frequency, which can be between 100 ksps (typical) and 40 Msps with fully specified performance at 40 Msps. The analog input voltage for both channels is acquired at the rising edge of the clock and the digital data for a given sample is delayed by the pipeline for 6 clock cycles. A choice of Offset Binary or Two’s Complement output format is selected with the OF pin. A logic high on the power down (PD) pin reduces the converter power consumption to 75 mW. Applications Information 1.3 Signal Inputs 1.0 OPERATING CONDITIONS The signal inputs are VIN+ and VIN−. The input signal, VIN, is defined as VIN = (VIN+) – (VIN−) Figure 2 shows the expected input signal range. Note that the common mode input voltage range is 1V to 3V with a nominal value of VA/2. The input signals should remain between ground and 4V. The Peaks of the individual input signals (VIN+ and VIN−) should each never exceed the voltage described as VIN+, VIN− = (VREF / 2 + VCM) ≤ 4V (differential) to maintain THD and SINAD performance. We recommend that the following conditions be observed for operation of the ADC12D040: 4.75V ≤ VA ≤ 5.25V VD = VA 2.35V ≤ VDR ≤ VD VREF/2 ≤ VCM ≤ VA - VREF 100 kHz ≤ fCLK ≤ 40 MHz 1.0V ≤ VREF ≤ 2.4V 1.1 Analog Inputs The ADC12D040 has two analog signal inputs, VIN+ and VIN−. These two pins form a differential input pair. There is one reference input pin, VREF. The analog input circuitry contains an input boost circuit that provides improved linearity over a wide range of analog input voltages. To prevent an on-chip over voltage condition that could impair device reliability, the input signal should never exceed the voltage described as VA - VREF/2. 1.2 Reference Pins The ADC12D040 is designed to operate with a 2.0V reference, but performs well with reference voltages in the range of 1.0V to 2.4V. Lower reference voltages will decrease the signal-to-noise ratio (SNR) of the ADC12D040. Increasing the reference voltage (and the input signal swing) beyond 2.4V may degrade THD for a full-scale input especially at higher input frequencies. It is important that all grounds associated with the reference voltage and the input signal make connection to the analog ground plane at a single point in that plane to minimize the effects of noise currents in the ground path. The ADC12040 will perform well with reference voltages up to 2.4V for full-scale input frequencies up to 10 MHz. However, more headroom is needed as the input frequency increases, so the maximum reference voltage (and input swing) will decrease for higher full-scale input frequencies. The six Reference Bypass Pins (VRPA, VRMA, VRNA, VRPB, VRMB and VRNB) are made available for bypass purposes. These pins should each be bypassed to ground with a 0.1 µF capacitor. Smaller capacitor values will allow faster recovery from the power down mode, but may result in degraded noise performance. DO NOT LOAD these pins. Loading any of these pins may result in performance degradation. 20046011 FIGURE 2. Expected Input Signal Range The ADC12D040 performs best with a differential input with each input centered around a common VCM. The peak-topeak voltage swing at both VIN+ and VIN− should not exceed the value of the reference voltage or the output data will be clipped. The two input signals should be exactly 180˚ out of phase from each other and of the same amplitude. For single frequency inputs, angular errors result in a reduction of the effective full scale input. For a complex waveform, however, angular errors will result in distortion. For single frequency sine waves with angular errors of less than 45˚ (π/4) between the two inputs, the full scale error in LSB can be described as approximately EFS = 2(n-1) * ( 1 - cos (dev) ) = 2048 * ( 1 - cos (dev) ) 15 www.national.com ADC12D040 The nominal voltages for the reference bypass pins are as follows: VRMA = VRMB = VA / 2 VRPA = VRPB = VRM + VREF / 2 VRNA = VRNB = VRM − VREF / 2 The VRN pins may be used as a common mode voltage source (VCM) for the analog input pins as long as no d.c. current is drawn from it. However, because the voltages at these pins are half that of the VA supply pin, using these pins for a common mode source will result in reduced input headroom (the difference between the VA supply voltage and the peak signal voltage at either analog input) and the possibility of reduced THD and SFDR performance. For this reason, it is recommended that VA always exceed VREF by at least 2 Volts. For high input frequencies it may be necessary to increase this headroom to maintain THD and SFDR performance. Functional Description ADC12D040 Applications Information quired and the resulting performance degradation is acceptable, one of the analog inputs should be connected to the d.c. mid point voltage of the driven input. The peak-to-peak differential input signal should be twice the reference voltage to maximize SNR and SINAD performance (Figure 2b). For example, set VREF to 1.0V, bias VIN− to 2.5V and drive VIN+ with a signal range of 1.5V to 3.5V. (Continued) Where dev is the angular difference between the two signals having a 180˚ relative phase relationship to each other (see Figure 3). Drive the analog inputs with a source impedance less than 100Ω. Because very large input signal swings can degrade distortion performance, better performance with a single-ended input can be obtained by reducing the reference voltage when maintaining a full-range output. Table 1 and Table 2 indicate the input to output relationship of the ADC12D040. 1.3.2 Driving the Analog Input The VIN+ and the VIN− inputs of the ADC12D040 consist of an analog switch followed by a switched-capacitor amplifier. The capacitance seen at the analog input pins changes with the clock level, appearing as 8 pF when the clock is low, and 7 pF when the clock is high. As the internal sampling switch opens and closes, current pulses occur at the analog input pins, resulting in voltage spikes at the signal input pins. As a driving amplifier attempts to counteract these voltage spikes, a damped oscillation may appear at the ADC analog inputs. The best amplifiers for driving the ADC12D040 input pins must be able to react to these spikes and settle before the switch opens and another sample is taken. The LMH6702 LMH6628 and the LMH6622, LMH6655 are good amplifiers for driving the ADC12D040. To help isolate the pulses at the ADC input from the amplifier output, use RCs at the inputs, as can be seen in Figure 4 and Figure 5. These components should be placed close to the ADC inputs because the input pins of the ADC is the most sensitive part of the system and this is the last opportunity to filter that input. For Nyquist applications the RC pole should be at the ADC sample rate. The ADC input capacitance in the sample mode should be considered when setting the RC pole. Setting the pole in this manner will provide best SNR performance. To obtain best SINAD and ENOB performance, reduce the RC time constant until SNR and THD are numerically equal to each other. To obtain best distortion and SFDR performance, eliminate the RC altogether. For undersampling applications, RC pole should be set at about 1.5 to 2 times the maximum input frequency to maintain a linear delay response. Note that the ADC12DL040 is not designed to operate with single-ended inputs. However, doing so is possible if the degraded performance is acceptable. See Section 1.3.1. Figure 4 shows a narrow band application with a transformer used to convert single-ended input signals to differential. Figure 5 shows the use of a fully differential amplifier for single-ended to differential conversion. 20046012 FIGURE 3. Angular Errors Between the Two Input Signals Will Reduce the Output Level or Cause Distortion TABLE 1. Input to Output Relationship – Differential Input VIN+ VIN− Binary Output 2’s Complement Output VCM − VREF/2 VCM + VREF/2 0000 0000 0000 1000 0000 0000 VCM − VREF/4 VCM + VREF/4 0100 0000 0000 1100 0000 0000 VCM VCM 1000 0000 0000 0000 0000 0000 VCM + VREF/4 VCM − VREF/4 1100 0000 0000 0100 0000 0000 VCM + VREF/2 VCM − VREF/2 1111 1111 1111 0111 1111 1111 TABLE 2. Input to Output Relationship – Single-Ended Input VIN+ VIN− Binary Output 2’s Complement Output VCM − VREF VCM 0000 0000 0000 1000 0000 0000 VCM − VREF/2 VCM 0100 0000 0000 1100 0000 0000 VCM VCM 1000 0000 0000 0000 0000 0000 VCM + VREF/2 VCM 1100 0000 0000 0100 0000 0000 VCM + VREF VCM 1111 1111 1111 0111 1111 1111 1.3.1 Single-Ended Operation Single-ended performance is lower than with differential input signals. For this reason, single-ended operation is not recommended. However, if single ended-operation is re- www.national.com 16 ADC12D040 Applications Information (Continued) 20046013 FIGURE 4. Application Circuit using Transformer or Differential Op-Amp Drive Circuit 20046014 FIGURE 5. Differential Drive Circuit using a fully differential amplifier. 2.1 CLK The CLK signal controls the timing of the sampling process. Drive the clock input with a stable, low jitter clock signal in the range of 100 kHz to 55 MHz with rise and fall times of less than 3ns. The trace carrying the clock signal should be as short as possible and should not cross any other signal line, analog or digital, not even at 90˚. If the CLK is interrupted, or its frequency too low, the charge on internal capacitors can dissipate to the point where the accuracy of the output data will degrade. This is what limits the lowest sample 1.3.3 Input Common Mode Voltage The input common mode voltage, VCM, should be of a value such that the peak excursions of the analog signal does not go more negative than ground or more positive than 1.0 Volts below the VA supply voltage. The nominal VCM should generally be about VREF/2. VRBA and VRBB can be used as VCM sources as long as no d.c. current is drawn from these pins. 2.0 DIGITAL INPUTS Digital TTL/CMOS compatible inputs consist of CLK, OEA, OEB, OF, INT/EXT REF, and PD. 17 www.national.com ADC12D040 Applications Information 2.4 The OF Pin (Continued) The output data format is offset binary when the OF pin is at a logic low or 2’s complement when the OF pin is at a logic high. While the sense of this pin may be changed "on the fly," doing this is not recommended as the output data could be erroneous for a few clock cycles after this change is made. The ADC clock line should be considered to be a transmission line and be series terminated at the source end to match the source impedance with the characteristic impedance of the clock line. It generally is not necessary to terminate the far (ADC) end of the clock line, but if a single clock source is driving more than one device (a condition that is generally not recommended), far end termination may be needed. Far end termination is a series RC with the resistor being the same as the characteristic impedance of the clock line. The capacitor should have a minimum value of 2.5 The INT/EXT REF Pin The INT/EXT REF pin determines whether the internal reference or an external reference voltage is used. With this pin at a logic low, the internal 2.0V reference is in use. With this pin at a logic high an external reference must be applied to the VREF pin, which should then be bypassed to ground. There is no need to bypass the VREF pin when the internal reference is used. There is no access to the internal reference voltage, but its value is approximately equal to VRP − VRN. See Section 1.2 20046060 where tPD is the propagation time in ns/unit length, "L" is the length of the line and ZO is the characteristic impedance of the line. The units of tPD and "L" should be consistent with each other. The typical board of FR-4 material has a tPD of about 150 ps/inch, or about 60 ps/cm. 3.0 DATA OUTPUT PINS The ADC12D040 has 24 TTL/CMOS compatible Data Output pins. Valid data is present at these outputs while the OE and PD pins are low. While the tOD time provides information about output timing, tOD will change with a change of clock frequency. At the rated 40 MHz clock rate, the data transition is about 6 to 10 ns after the rise of the clock and about 4 to 10 ns before the fall of the clock (depending upon VDR), so either clock edge may be used to capture data, depending upon the data setup time of the circuit accepting the data. Also, circuit board layout will affect relative delays of the clock and data, so it is important to consider these relative delays when designing the digital interface. At sample frequencies below 40 MHz, there is a longer time between data transition and the fall of the clock, so that the falling edge of the clock is generally the best edge to use for output data capture at low sample rates. Be very careful when driving a high capacitance bus. The more capacitance the output drivers must charge for each conversion, the more instantaneous digital current flows through VDR and DR GND. These large charging current spikes can cause on-chip ground noise and couple into the analog circuitry, degrading dynamic performance. Adequate bypassing, limiting output capacitance and careful attention to the ground plane will reduce this problem. Additionally, bus capacitance beyond the specified 20 pF/pin will cause tOD to increase, making it difficult to properly latch the ADC output data. The result could be an apparent reduction in dynamic performance. To minimize noise due to output switching, minimize the load currents at the digital outputs. This can be done by connecting buffers (74AC541, for example) between the ADC outputs and any other circuitry. Only one driven input should be connected to each output pin. Additionally, inserting series resistors of about 100Ω at the digital outputs, close to the ADC pins, will isolate the outputs from trace and other circuit capacitances and limit the output currents, which could otherwise result in performance degradation. See Figure 4. Note that, although the ADC12D040 has Tri-State outputs, these outputs should not be used to drive a bus and the charging and discharging of large capacitances can degrade SNR performance. Each output pin should drive only one pin of a receiving device and the interconnecting lines should be as short as practical. The far end termination should be near but beyond the ADC clock pin as seen from the clock source. The duty cycle of the clock signal can affect the performance of any A/D Converter. Because achieving a precise duty cycle is difficult, the ADC12040 is designed to maintain performance over a range of duty cycles. While it is specified and performance is guaranteed with a 50% clock duty cycle, performance is typically maintained over a clock duty cycle range of 40% to 60%. Take care to maintain a constant clock line impedance throughout the length of the line. Refer to Application Note AN-905 for information on setting characteristic impedance. 2.2 OEA, OEB The OEA and OEB pin, when high, put the output pins of their respective converters into a high impedance state. When either of these pins is low the corresponding outputs are in the active state. The ADC12D040 will continue to convert whether these pins are high or low, but the output can not be read while the pin is high. Since ADC noise increases with increased output capacitance at the digital output pins, do not use the TRI-STATE outputs of the ADC12L066 to drive a bus. Rather, each output pin should be located close to and drive a single digital input pin. To further reduce ADC noise, a 100 Ω resistor in series with each ADC digital output pin, located close to their respective pins, should be added to the circuit. 2.3 The PD Pin The PD pin, when high, holds the ADC12D040 in a powerdown mode to conserve power when the converter is not being used. The power consumption in this state is 75 mW with a 40 MHz clock and 40mW if the clock is stopped when PD is high. The output data pins are undefined in the power down mode and the data in the pipeline is corrupted while in the power down mode. The Power Down Mode Exit Cycle time is determined by the value of the capacitors on pins 4, 5, 6, 12, 13 and 14. These capacitors loose their charge in the Power Down mode and must be recharged by on-chip circuitry before conversions can be accurate. Smaller capacitor values allow faster recovery from the power down mode, but can result in a reduction in SNR, SINAD and ENOB performance. www.national.com 18 5.0 LAYOUT AND GROUNDING Proper grounding and proper routing of all signals are essential to ensure accurate conversion. Maintaining separate analog and digital areas of the board, with the ADC12D040 between these areas, is required to achieve specified performance. The ground return for the data outputs (DR GND) carries the ground current for the output drivers. The output current can exhibit high transients that could add noise to the conversion process. To prevent this from happening, the DR GND pins should NOT be connected to system ground in close proximity to any of the ADC12D040’s other ground pins. (Continued) 4.0 POWER SUPPLY CONSIDERATIONS The power supply pins should be bypassed with a 10 µF capacitor and with a 0.1 µF ceramic chip capacitor within a centimeter of each power pin. Leadless chip capacitors are preferred because they have low series inductance. As is the case with all high-speed converters, the ADC12D040 is sensitive to power supply noise. Accordingly, the noise on the analog supply pin should be kept below 100 mVP-P. No pin should ever have a voltage on it that is in excess of the supply voltages, not even on a transient basis. Be especially careful of this during turn on and turn off of power. The VDR pin provides power for the output drivers and may be operated from a supply in the range of 2.35V to VD (nominal 5V). This can simplify interfacing to low voltage devices and systems. Note, however, that tOD increases with reduced VDR. DO NOT operate the VDR pin at a voltage higher than VD. Capacitive coupling between the typically noisy digital circuitry and the sensitive analog circuitry can lead to poor performance. The solution is to keep the analog circuitry separated from the digital circuitry, and to keep the clock line as short as possible. The effects of the noise generated from the ADC output switching can be minimized through the use of 100Ω resistors in series with each data output line. Locate these resistors as close to the ADC output pins as possible. 20046016 FIGURE 6. Example of a Suitable Layout 19 www.national.com ADC12D040 Applications Information ADC12D040 Applications Information (Continued) Since digital switching transients are composed largely of high frequency components, total ground plane copper weight will have little effect upon the logic-generated noise. This is because of the skin effect. Total surface area is more important than is total ground plane volume. Generally, analog and digital lines should cross each other at 90˚ to avoid crosstalk. To maximize accuracy in high speed, high resolution systems, however, avoid crossing analog and digital lines altogether. It is important to keep clock lines as short as possible and isolated from ALL other lines, including other digital lines. Even the generally accepted 90˚ crossing should be avoided with the clock line as even a little coupling can cause problems at high frequencies. This is because other lines can introduce jitter into the clock line, which can lead to degradation of SNR. Also, the high speed clock can introduce noise into the analog chain. 20046017 FIGURE 7. Isolating the ADC Clock from other Circuitry with a Clock Tree Best performance at high frequencies and at high resolution is obtained with a straight signal path. That is, the signal path through all components should form a straight line wherever possible. Be especially careful with the layout of inductors. Mutual inductance can change the characteristics of the circuit in which they are used. Inductors should not be placed side by side, even with just a small part of their bodies beside each other. The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input. Any external component (e.g., a filter capacitor) connected between the converter’s input pins and ground or to the reference input pin and ground should be connected to a very clean point in the analog ground plane. Figure 6 gives an example of a suitable layout. All analog circuitry (input amplifiers, filters, reference components, etc.) should be placed in the analog area of the board. All digital circuitry and I/O lines should be placed in the digital area of the board. The ADC12DL040 should be between these two areas. Furthermore, all components in the reference circuitry and the input signal chain that are connected to ground should be connected together with short traces and enter the analog ground plane at a single, quiet point. All ground connections should have a low inductance path to ground. 7.0 COMMON APPLICATION PITFALLS Driving the inputs (analog or digital) beyond the power supply rails. For proper operation, all inputs should not go more than 100 mV beyond the supply rails (more than 100 mV below the ground pins or 100 mV above the supply pins). Exceeding these limits on even a transient basis may cause faulty or erratic operation. It is not uncommon for high speed digital components (e.g., 74F devices) to exhibit overshoot or undershoot that goes above the power supply or below ground. A resistor of about 47Ω to 100Ω in series with any offending digital input, close to the signal source, will eliminate the problem. Do not allow input voltages to exceed the supply voltage, even on a transient basis. Not even during power up or power down. Be careful not to overdrive the inputs of the ADC12D040 with a device that is powered from supplies outside the range of the ADC12D040 supply. Such practice may lead to conversion inaccuracies and even to device damage. Attempting to drive a high capacitance digital data bus. The more capacitance the output drivers must charge for each conversion, the more instantaneous digital current flows through VDR and DR GND. These large charging current spikes can couple into the analog circuitry, degrading dynamic performance. Adequate bypassing and maintaining separate analog and digital areas on the pc board will reduce this problem. Additionally, bus capacitance beyond the specified 20 pF/pin will cause tOD to increase, making it difficult to properly latch the ADC output data. The result could, again, be an apparent reduction in dynamic performance. The digital data outputs should be buffered (with 74AC541, for example). Dynamic performance can also be improved by adding series resistors at each digital output, close to the ADC12D040, which reduces the energy coupled back into the converter output pins by limiting the output current. A reasonable value for these resistors is 100Ω. Using an inadequate amplifier to drive the analog input. As explained in Section 1.3, the capacitance seen at the input alternates between 8 pF and 7 pF, depending upon the phase of the clock. This dynamic load is more difficult to drive than is a fixed capacitance. If the amplifier exhibits overshoot, ringing, or any evidence of instability, even at a very low level, it will degrade performance. A small series resistor at each amplifier output and a capacitor across the analog inputs (as shown in Figure 5) will 6.0 DYNAMIC PERFORMANCE To achieve the best dynamic performance, the clock source driving the CLK input must be free of jitter. Isolate the ADC clock from any digital circuitry with buffers, as with the clock tree shown in Figure 7. The gates used in the clock tree must be capable of operating at frequencies much higher than those used if added jitter is to be prevented. Best performance will be obtained with a differential input drive, compared with a single-ended drive, as discussed in Sections 1.3.1 and 1.3.2. As mentioned in Section 5.0, it is good practice to keep the ADC clock line as short as possible and to keep it well away from any other signals. Other signals can introduce jitter into the clock signal, which can lead to reduced SNR performance, and the clock can introduce noise into other lines. Even lines with 90˚ crossings have capacitive coupling, so try to avoid even these 90˚ crossings of the clock line. www.national.com 20 Operating with the reference pins outside of the specified range. As mentioned in Section 1.2, VREF should be in the range of 1.0V ≤ VREF ≤ 2.4V (Continued) improve performance. The LMH6702 and the LMH6628 have been successfully used to drive the analog inputs of the ADC12D040. Also, it is important that the signals at the two inputs have exactly the same amplitude and be exactly 180o out of phase with each other. Board layout, especially equality of the length of the two traces to the input pins, will affect the effective phase between these two signals. Remember that an operational amplifier operated in the non-inverting configuration will exhibit more time delay than will the same device operating in the inverting configuration. Operating outside of these limits could lead to performance degradation. Using a clock source with excessive jitter, using excessively long clock signal trace, or having other signals coupled to the clock signal trace. This will cause the sampling interval to vary, causing excessive output noise and a reduction in SNR and SINAD performance. 21 www.national.com ADC12D040 Applications Information ADC12D040 Dual 12-Bit, 40 MSPS, 600 mW A/D Converter with Internal/External Reference Physical Dimensions inches (millimeters) unless otherwise noted 64-Lead TQFP Package Ordering Number ADC12D040CIVS NS Package Number VECO64A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560