2530 System on Chip Series A2530R24AZ1 The A2530R24AZ1 is a high-performance, FCC & IC certified and ETSIcompliant radio module that incorporates the Texas Instruments CC2530 SOC and integral antenna, all in the industry’s smallest package: 11 x 19 x 2.5 mm. The module comes pre-loaded with Anaren’s AIR-ZNP firmware for the ZigBee®* Standard. Benefits Features General: 2.4-GHz IEEE 802.15.4 compliant RF transceiver Excellent receiver sensitivity and robustness to interference (-90dBm average) Wide input voltage range (2.2V – 3.6V) 100% RF tested in production Module weight approximately 0.7 grams Current Consumption: (TC = 25°C, VDD = 3.0V) Active mode RX (CPU Idle): 25 mA Active mode TX (CPU Idle): 29 mA @0dBm, 34mA @4dBm (module MAX output power, complies with FCC, IC and ETSI limits) 3 Low power/sleep modes from 1uA to 200 uA Microcontroller: High-performance and low-power 8051 Microcontroller core with code prefetch 256KB in-system programmable flash and 8KB RAM with retention in all power modes Firmware: Preloaded with Anaren’s AIR-ZNP firmware, based on the TI Z-Stack™ for the ZigBee® Standard Supports SPI and UART communication Driver library included for MSP430™ and Stellaris® MCUs, which abstracts functionality Over 30 code examples for a paired MCU included to demonstrate functionality, including: Button Blink: Blinks LED when button pressed Hello World: Outputs ‘Hello World’ to the PC via USB Get Module Version: Displays module version Get MAC Address: Displays internal MAC address Write NV Items: Writes to user-accessible non-volatile memory Read NV Items: Reads user-accessible non-volatile memory Read Radio GPIO: Displays value of module GPIO 1-4 Write Radio GPIO: Writes values to module GPIO 1-4 Coordinator Function: AF/ZDO, Simple API, or Secure Router Function: AF/ZDO, Simple API, or Secure End Point Function: AF/ZDO RF Tester: RF test utility Range Test: Test utility to show link quality (LQI) Packet Error Test: Test utility to show packet error rate (PER) AND MANY MORE! * The terms ZigBee®, ZigBee® Alliance, and ZigBee® Standard are registered trademarks of ZigBee® Minimal RF engineering experience necessary Minimal ZigBee® experience necessary Easy to program and implement, short design cycle No additional “Intentional Radiator” certification required (FCC CFR 47 Part 15, IC RSS-210) Minimal real estate required Easily implemented on a two layer PCB No additional harmonic filtering required 100% RF-tested in production Common footprint for similar products in family No additional DC decoupling required Includes IEEE 802.15.4 MAC Timer CSMA/CA hardware support Accurate Digital RSSI/LQI support Battery monitor and temperature sensor AES Security co processor Operating temperature –40 to +85˚C Applications ZigBee® Light Link control systems, ZigBee® systems, Home/building automation, lighting systems, low power wireless sensor networks, consumer electronics, industrial control and monitoring. PLEASE NOTE: Additional information on the Texas Instruments CC2530 device can be found in the company’s latest datasheet release at http://www.ti.com This product is not to be used in any implantable medical device or external medical device intended to regulate or monitor biological functions, including but not limited to devices such as pacemakers, defibrillators, cardiac resynchronization devices, pressure sensors, biochemical stimulators and neurostimulators. ANAREN MAKES NO WARRANTY OF FITNESS OR MERCHANTABILITY OF THIS PRODUCT FOR ANY USE OF THIS TYPE. Anaren shall not be responsible for any consequential damages arising from the sale or use of this product for any use of this type. The ultimate user of the product assumes all risk of personal injury or death arising from a prohibited use. Anaren, Inc. / 6635 Kirkville Road / East Syracuse, NY 13057 800.411.6596 / http://www.anaren.com / [email protected] Product overview Module Block Diagram The A2530R24AZ1 is a high-performance, FCC & IC certified and ETSI-compliant ZigBee®/IEEE 802.15.4 RF SOC module that incorporates the Texas Instruments CC2530 transceiver chip in the industry’s smallest package (11 x 19 x 2.5 mm). The module incorporates a crystal, the required RF matching and filtering for regulatory compliance, plus filtering on select digital lines for better noise reduction and sensitivity. The modules operate in the global non-licensed 2.4GHz ISM/SRD frequency band. These radio modules are ideal for achieving low power wireless connectivity without having to deal with extensive Protocol, RF design and regulatory compliance, allowing quick time to market. The modules are 100% RF-tested to provide consistent performance. The A2530R24AZ1 has an RoHS-compliant ENIG finish and is packaged on tape & reel or in matrix trays for high-volume automated manufacturing. Layout Information See product User’s Manual for detailed information. Pin diagram Pin-out shown is for operation using the AIR-ZNP firmware for the ZigBee® Standard. See User’s Manual for detailed pin descriptions. Ground detail (corner) DNC = “Do Not Connect”. Pin reserved for internal use, ensure mating footprint pads are isolated. GND = “Ground”. Connect the maximum number possible (minimum one for proper operation). Footprint (PWB) Ground detail (edge) Nomenclature Caution! ESD sensitive device. Precautions should be used when handling the device in order to prevent permanent damage. A 1 2 3 4 5 Chip series Function Frequency band Form factor Design ID 6 Application 7 Packaging (Anaren) (CC1101, CC2500, CC2530, CC8520) (R = radio only, E = Range Extender) (x 100MHz) (A = Internal Antenna, C = Connector) (Z1 = Loaded with Anaren AIR-ZNP for the ZigBee® Standard) (G = General) (R = Reel, M = Matrix Tray) 1237a Anaren, Inc. / 6635 Kirkville Road / East Syracuse, NY 13057 800.411.6596 / http://www.anaren.com / [email protected]