APITECH BXP9421

Available as:
RF AMPLIFIER
MODEL TN9421
Features
TN9421, 4 Pin .450” Sq. Surface Mount (SM3)
BX9421, SMA Connectorized Housing (H1L-Laser)
BXP9421, SMA Connectorized Housing (HPak)
Typical Intermodulation Performance at 25 ºC*

Wide Bandwidth 950-4200 MHz
 Low Noise Figure: 1.8 dB Typical

Cross to the Cougar AS4221, our Model TN9421
Cross to the Cougar ACP4221, our Model BXP9421
Environmental Screening Available
Second Order Harmonic Intercept Point....... +48 dBm (Typ.)
Second Order Two Tone Intercept Point.........+42 dBm (Typ.)
Third Order Two Tone Intercept Point.............+26 dBm (Typ.)
*Typical @ 25 ºC
Specifications
CHARACTERISTIC
Frequency
Gain
Gain Flatness
Noise Figure
VSWR
In
Out
Power Output
@ 1 dB Comp.
Vdc
mA
MIN/MAX
Ta = -55 ºC to +85 ºC
950 - 4200 MHz
13.0 dB
11.5 dB Min.
+/- 0.5 dB
+/- 1.0 Max.
1.8 dB
2.7 dB Max.
1.7:1
1.7:1
2.0:1 Max.
2.0:1 Max.
+14.0 dBm
Reverse Isolation
Power
TYPICAL
Ta= 25 ºC
950 - 4200 MHz
Absolute Maximum (No Damage) Ratings
Ambient Operating Temperature ................ -55ºC to +100 ºC
Storage Temperature ................................. -62ºC to +125 ºC
DC Voltage .......................................................... +20 Volts
Continuous RF Input Power ................................. +7.5 dBm
Short Term RF Input Power .......... +10 dBm (1 Minute Max.)
Maximum Peak Power ................... +13 dBm (3 μsec Max.)
Note: Measured in a 50 ohm system at +15 volts DC.
Note: Care should always be taken to effectively ground the case of each unit.
Revision 5/14/2012
+12.5 dBm Min.
23 dB
+15
40
+15
46 Max.
Typical Performance Data
Gain (dB)
14
Reverse Isolation (dB)
0
Noise Figure (dB)
5
-10
4
12
-20
3
11
-30
2
10
-40
1
13
Stop 4200 MHz
Start 950 MHz
+16
Stop 4200 MHz
Start 950 MHz
1 dB Comp. (dBm)
Input VSWR
2.0
2.0
1.5
1.5
Start 950 MHz
Stop 4200 MHz
Output VSWR
+15
+14
+13
+12
1.0
Start 950 MHz
Legend
Stop 4200 MHz
+25 ºC
Start 950 MHz
Stop 4200 MHz
1.0
Start 950 MHz
Stop 4200 MHz
+85 ºC - - - - - - -55 ºC
Spectrum Microwave · 2144 Franklin Drive N.E. · Palm Bay, Florida 32905 · PH (888) 553-7531 · Fax (888) 553-7532
www.SpectrumMicrowave.com Spectrum Microwave · 2707 Black Lake Place · Philadelphia, Pennsylvania 19154 · PH (215) 464-4000 · Fax (215) 464-4001
4
3
DWG NO.
SH
088-00304
1
REV
OF
1
P1
1
REVISIONS
11.56
.46
8.38
.33
2X
2X SMA
CONNECTOR
VDC
B
14.61
.58
RF IN
SMI
RF OUT
XXXXXX
XXXX
19.56
.77
REV.
DESCRIPTION
CHNG/DATE
XXX
P1
PRELIMINARY RELEASE
2012/05/14
APPVD/DATE
4.57
.18
0.76
.03
6.36
.25
ECN
7.30
.29
B
9.53
.38
TYP.
CAUTION
THIS ASSEMBLY CONTAINS PARTS SENSITIVE
TO DAMAGE BY ELECTROSTATIC DISCHARGE (ESD).
USE ESD PRECAUTIONARY PROCEDURES WHEN
TOUCHING, REMOVING OR INSERTING
8.38
.33
MAX.
38.61
1.52
3.62
.14
A
1.78
.07
11.05
.44
A
SEE SEPARATE PARTS LIST IN ELECTRONIC STORAGE
.10[2.54]
4 X 2-56 UNC
MOUNTING HOLES
GROUND TAB
* INTERPRET DRAWING IAW ASME Y14.100-2004
* PARENTHETICAL INFORMATION FOR REFERENCE ONLY
* DIMENSIONAL LIMITS APPLY BEFORE PROCESSES
* DIMENSIONS ARE IN INCHES
* TOLERANCES ARE: ANGLES ±1.0°
* SURFACE FINISH
63
2 PLACE DECIMAL ±.02
3 PLACE DECIMAL ±.005
* REMOVE ALL BURRS AND SHARP EDGES .010 RAD MAX.
SPECTRUM MICROWAVE PROPRIETARY INFORMATION
THIS DOCUMENT IS THE SOLE PROPERTY OF SPECTRUM MICROWAVE, INC.
THE RELEASE OF DATA CONTAINED IN THIS DOCUMENT AND THE
REPRODUCTION OF THIS DOCUMENT, IN WHOLE OR IN PART, WITHOUT THE
WRITTEN PERMISSION OF SPECTRUM MICROWAVE, INC ARE PROHIBITED.
COMPUTER ASSISTED DRAWING
GENERATED USING SOLIDWORKS 2007
FORM NO. 1054 SIZE B1
4
3
SPECTRUM MICROWAVE, INC
ANSI
* DIMENSIONING AND TOLERANCING IAW ASME Y14.5-1994
12.32
.49
3rd ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
* CONCENTRICITY MACHINED DIA: .002 FIM
* MACHINED TOOL MISMATCH: .002 MAX.
DRAWN
WAR
2707 Black Lake Place
Philadelphia, PA 19154-1008 (USA)
DATE
2012/05/14
TITLE
CHECKED
ENGRG
H PHAM
OUTLINE, HPAK
2012/05/14
MFG
SIZE
CAGE CODE
B 60979
QA
SCALE:
DO NOT SCALE DRAWING
2
DWG NO.
REV
088-00304
SHEET
1.5:1
1
P1
1
OF
1
4
3
DWG NO.
SH
088-00304
1
REV
OF
1
P1
1
REVISIONS
11.56
.46
8.38
.33
2X
2X SMA
CONNECTOR
VDC
B
14.61
.58
RF IN
SMI
RF OUT
XXXXXX
XXXX
19.56
.77
REV.
DESCRIPTION
CHNG/DATE
XXX
P1
PRELIMINARY RELEASE
2012/05/14
APPVD/DATE
4.57
.18
0.76
.03
6.36
.25
ECN
7.30
.29
B
9.53
.38
TYP.
CAUTION
THIS ASSEMBLY CONTAINS PARTS SENSITIVE
TO DAMAGE BY ELECTROSTATIC DISCHARGE (ESD).
USE ESD PRECAUTIONARY PROCEDURES WHEN
TOUCHING, REMOVING OR INSERTING
8.38
.33
MAX.
38.61
1.52
3.62
.14
A
1.78
.07
11.05
.44
A
SEE SEPARATE PARTS LIST IN ELECTRONIC STORAGE
.10[2.54]
4 X 2-56 UNC
MOUNTING HOLES
GROUND TAB
* INTERPRET DRAWING IAW ASME Y14.100-2004
* PARENTHETICAL INFORMATION FOR REFERENCE ONLY
* DIMENSIONAL LIMITS APPLY BEFORE PROCESSES
* DIMENSIONS ARE IN INCHES
* TOLERANCES ARE: ANGLES ±1.0°
* SURFACE FINISH
63
2 PLACE DECIMAL ±.02
3 PLACE DECIMAL ±.005
* REMOVE ALL BURRS AND SHARP EDGES .010 RAD MAX.
SPECTRUM MICROWAVE PROPRIETARY INFORMATION
THIS DOCUMENT IS THE SOLE PROPERTY OF SPECTRUM MICROWAVE, INC.
THE RELEASE OF DATA CONTAINED IN THIS DOCUMENT AND THE
REPRODUCTION OF THIS DOCUMENT, IN WHOLE OR IN PART, WITHOUT THE
WRITTEN PERMISSION OF SPECTRUM MICROWAVE, INC ARE PROHIBITED.
COMPUTER ASSISTED DRAWING
GENERATED USING SOLIDWORKS 2007
FORM NO. 1054 SIZE B1
4
3
SPECTRUM MICROWAVE, INC
ANSI
* DIMENSIONING AND TOLERANCING IAW ASME Y14.5-1994
12.32
.49
3rd ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
* CONCENTRICITY MACHINED DIA: .002 FIM
* MACHINED TOOL MISMATCH: .002 MAX.
DRAWN
WAR
2707 Black Lake Place
Philadelphia, PA 19154-1008 (USA)
DATE
2012/05/14
TITLE
CHECKED
ENGRG
H PHAM
OUTLINE, HPAK
2012/05/14
MFG
SIZE
CAGE CODE
B 60979
QA
SCALE:
DO NOT SCALE DRAWING
2
DWG NO.
REV
088-00304
SHEET
1.5:1
1
P1
1
OF
1