AZ DISPLAYS SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY Ć TM0350D2 Z DISPLAYS VER2.2 REVISION RECORD REVISION REVISION DATE PAGE CONTENTS VER1.0 2008-07-10 FIRST ISSUE VER2.0 2011-08-22 UPDAT E LCD VER2.1 VER2.2 2013-04-12 2013-05-02 8 4,5 MODIFY OPTICAL CHARACTERISTICS UPDATE VIEWING ANGLE INFORMATION CONTENTS 1. LCD MODULE PHYSICAL DATA …………………………………...4 2. OUTLINE DIMENSIONS ………………………………………………5 3. BLOCK DIAGRAM …………………………………………………….6 4. ABSOLUTE MAXIMUM RATINGS ………………………………….6 5. ELECTRICAL CHARACTERISTICS ………………………………..7 6. ELECTRO-OPTICAL CHARACTERISTICS ……………………….8 7. SIGNAL TIMING DIAGRAM…………………………………………11 8. INTERFACE PIN CONNECTIONS ………………………………….16 9. INITIALIZED CODE ………………………………………………….16 10. SPECIFICATION OF QUALITY ASSURANCE ………………….. .17 11. RELIABILITY ………………………………………………………….23 12. USING LCD MODULES ………………………………………………24 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 1 LCD MODULE PHYSICAL DATA 1.1 General Description Display Type TFT/Transmissive Connection Type COG + FPC Operation temperature -20ć ~70ć Storage temperature -30ć ~80ć Driving IC HX8238-D MPU interface RGB interface Table 1. 1.2 Mechanical Description Item Standard Value Unit 3.5 inch Number of dots 320RGB x 240 dots - LCM dimension 76.90(W ) x 63.90(H) x 3.20(T) mm Active area 70.08(W) x 52.56H) mm Dot size 0.219(W) x 0.219(H) mm TBD g Screen size Approx. weight Backlight 6 chip white LED in series Table 2. AZ DISPLAYS 1 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 2 OUTLINE DIMENSIONS AZ DISPLAYS 2 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 3 BLOCK DIAGRAM Figure 2. 4 ABSOLUTE MAXIMUM RATINGS ITEM SYMBOL CONDITION STANDARD VALUE UNIT Power Supply Voltage(1) VDD Ta= +25ć MIN -0.3 Power Supply Voltage(2) Iovcc Ta= +25ć -0.3 - 4.6 V Power Supply Voltage(3) Vci Ta= +25ć -0.3 - 4.6 V Input Voltage Vin Ta=+25ć -0.3 - Vcc+0.3 V Operating Temperature Top --- - 20 - +70 ć Storage Temperature Tst - 30 - +80 ć --Table 3. TYP - MAX 4.6 V NOTE: (1). If the module is used above these absolute maximum ratings. It may become permanently damaged. Using the module within the following electrical characteristic conditions are also exceeded, the module will malfunction and cause poor reliability (2). LCM should be grounded during handing LCM. (3). VDD>GND must be maintained. AZ DISPLAYS 3 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 5 ELECTRICAL CHARACTERISTICS 5.1 DC Characteristics ITEM SYMBOL STANDARD VALUE CONDITION S UNIT MIN TYP MAX VCI Ta= +25ć 2.8 3.0 3.3 VDDIO Ta= +25ć 1.8 3.0 3.3 Input High Voltage for LCD VIH ˉ 0.8Iovcc ˉ Iovcc V Input Low Voltage for LCD VIL ˉ Vss ˉ 0.2 Iovcc V Output High Voltage for LCD VOH ˉ 0.8Iovcc ˉ Iovcc V Output Low Voltage for LCD VOL ˉ Vss ˉ 0.2 Iovcc V Power Supply Voltage for Logic Power Supply Voltage for I/O circuit V Table 4. 5.2 Back-Light unit PARAMETER SYMBOL REMARK STANDARD VALUE UNIT FORWARD VOLTAGE VF If =20mA MIN 18.0 LUMINOUS INTENSITY(INCLUDE LCD) Iv If =20mA 380 400 - cd/m2 Iv-m (min/max)/100 - 80 - % LUMINOUS TOLERANCE CHROMATICITY COORDINATES(INCLUDE LCD) X Y If =20mA TYP 19.2 MAX 20.4 V 0.270 0.310 0.290 0.330 OPERATING TEMPERATURE -20ć ~ 70ć STORAGE TEMPERATURE -30ć ~ 80ć Table 5. 5.3 AC Characteristics Refer to HX8238-D data sheet. AZ DISPLAYS 4 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 6 ELECTRO-OPTICAL CHARACTERISTICS Paramete Threshold voltage Viewing Angle range Symbol Condition Min Typ Max Unit Vsat 2.7 3.3 3.8 V Vth 1.2 1.5 1.8 V Left(9’) 70 75 - Deg 70 75 - Deg Up(12’) 50 55 - Deg Down(6’) 55 60 - Deg Remark Note 1 Horizontal Right(3’) CR > 10 Not 2 Vertical Contrast ratio C/R = 0° - 300 - Not 3 Transmittance T(%) = 0° - 7.4 - Not 4 Response Time Tr+Tf = 0° 30 msec Not 6 Table 6. Note : 1. The definition of Vth & Vsat Figure 3. The definition of Vth & Vsat AZ DISPLAYS 5 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 2.Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface. Figure 4.Definition of viewing angle 3. Contrast measurements shall be made at viewing angle of = 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. CR Luminance when displaying a white raster Luminance when displaying a black raster 4. Transmittance is the value with Polarizer. 5. The color chromaticity coordinates specified in Table 6. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the C/F. Measurement condition is C - light source & Halogen Lamp. AZ DISPLAYS 6 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 Figure 5 Optical test equipment. 6. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td Figure 6.Definition of response time: Tr+Tf AZ DISPLAYS 7 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 7 SIGNAL TIMING DIAGRAM 7.1 DC Characteris Figure 7. DC Characteris AZ DISPLAYS 8 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 7.2 AC Characteris Figure 8. Pixel Timing Figure 9. Pixel Timing AZ DISPLAYS 9 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 Figure 10. Data Transaction Timing in Parallel RGB (24 bits) SYNC MODE Figure 11. AZ DISPLAYS Data Transaction Timing in Normal Operating MODE 10 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 7.3 Power Up Sequence Figure 12. Power Up Sequence AZ DISPLAYS 11 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 7.4 Power Up Sequence Figure 13. Power Down Sequence AZ DISPLAYS 12 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 8 INTERFACE PIN CONNECTIONS PIN NO. SYMBOL 1~2 LED- The backlight ground 3~4 LED+ Power supply for backlight 5~7 NC 8 RESET 9 CS Chip select 10 SCL Clock synchronization signal 11 SDI SPI serial signal 12~19 B0~B7 B signal Data bus 20~27 G0~G7 G signal Data bus 28~35 R0~R7 R signal Data bus 36 HSYNC Line synchronization signal 37 VSYNC Frame synchronization signal 38 DOTCLK 39~40 NC 41~42 VDD 43~47 NC 78 XR 49 YD 50 XL 51 YU 52 ENB A data ENABLE signal in RGB I/F mod 53~54 GND Ground FUNCTION DESCRIPTIONS No connection LCD Reset signal DOT synchronization signal No connection Power supply for logic circuit No connection Touch panel select pin( No connection) Table 6. 9 INITIALIZED CODE Please contact us for details. AZ DISPLAYS 13 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 10 SPECIFICATION OF QUALITY ASSURANCE 10.1 Summary The customer should check and accept the products of ZET within one month after reception. This standard for Quality Assurance should affirm the quality of LCD products to supply to purchaser by ZET COMPANY LIMITED. Entire process is controlled according to QS9000. 10.2 Standard for quality test (1) Inspection Before delivering, the supplier should take the following tests, and affirm the quality of product. (2) Electro-Optical Characteristics According to the individual specification to test the product. (3) Test of Appearance Characteristics: According to the individual specification to test the product. (4)Test of Reliability Characteristics According to the definition of reliability on specification for test product. (5) Delivery Test Before delivering, the supplier should take the delivery test (6)Sampling Method: GB/T2828.1-2003, Level II (7) The defects classify of AQL as following Major defect: AQL=0.65 Minor defect: AQL=1.5 10.3 Nonconforming Analysis & Deal With Manners ƿNonconforming Analysis (1) Purchaser should supply the detail data of nonconforming sample and the non-suitable state. (2) After accepting the detail data from purchaser ,the analysis of nonconforming should be finished in two weeks. (3) If supplier can not finish analysis on time ,must announce purchaser before two weeks. ƿDisposition of nonconforming (1) If find any supplier defect during assembly line, supplier must change the good product for every defect after recognition. (2) Both supplier and customer should analysis the reason and discuss the disposition of nonconforming when the reason of nonconforming is not sure. AZ DISPLAYS 14 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 10.4 Agreement items. Both sides should discuss together when the following problems happen: (1) There is any problem of standard of quality assurance ,and both sides think that must be modifier. (2) There is any argument item which does not record in the quality assurance. (3) Any other special problem. 10.5 Standard of the Product Appearance Test 10.5.1 Manner of appearance test (1) The test must be under 20W*2 or 40W fluorescent light ,and the distance of view must be at 30±5 cm. (2) When test the model of Transmissive product must add the reflective plate. (3) The test direction is base on about around 30 degree(within range)of vertical line. Vertical line Eyes Figure 14. AZ DISPLAYS 15 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 (4) Definition of Area: A Area: Active area B Area: Viewing area C Area: Out of viewing area D Area: Seal area C Area B Area A Area D Area Figure 15. 10.5.2 Basic principle: (1) It will accord to the AQL when the standard can not be described. (2) The sample of the lowest acceptable quality level must be discussed by both supplier and customer when any dispute happened. (3) Must add new item on time when it is necessary. AZ DISPLAYS 16 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 10.6 Inspection specification NO 01 Item Electrical Testing Criterion AQL 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character, dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 1.5 Current consumption exceeds product specifications. 1.6 LCD viewing angle defect. 1.7 Contrast defect 0.65 2.1Round type: As following drawing =(x+y)/2 X Size LCD black spots, white spots, color 02 spots, contamination, scratches (display/non-displa y) ̰0.20 0.20<̰ 0.25 0.25 ̰̰0.3 0 0.30< Total Y Acceptable QTY A.A Ignore Remark V.A Ignore 2 3 1 2 0 3 0 5 No more than two spots within 5mm 1.5 2.2 Line Type: (As following drawing) W L Length Width --L̰2.5 W̰0.03 0.03< Acceptable QTY V.A A.A Ignore Ignore 2 3 W̰0.05 L̰1.5 0.05< W̰0.08 --- AZ DISPLAYS 0.08< W Remark No more than two lines within 5mm 0 0 17 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 If bubbles are visible, judge using black spot specification, not easy to find, must check in specify direction. 03 Polarizer bubbles Ignore Size ̰0.30 0.30<̰0.60 Acceptable QTY A. A V. A Ignore Ignore 2 3 0 0 1.5 Symbols: a: Chip length b: Chip width c: Chip thickness t: Glass thickness 4.1 ITO electrode 4.2 General ,corner portion 04 AZ DISPLAYS Chipped glass 1.5 18 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 05 06 Cracked glass Backlight elements The LCD with extensive crack is not acceptable. 0.65 6.1 Illumination source flickers when lit. 0.65 6.2 Spots or scratches that appear when lit must be judged 1.5 using LCD spot, lines and contamination standards. 6.3 Backlight doesn’t light or color is wrong 0.65 7.1 No unmelted solder paste may be present on the PCB. 1.5 7.2 No cold solder joints, missing solder connections, oxidation 07 Soldering or icicle. 1.5 7.3 No residue or solder balls on PCB. 7.4 No short circuits in components on PCB. 1.5 0.65 8.1 No oxidation, contamination, curves or, bends on interface 1.5 pin (OLB) of TCP. 8.2 No cracks on interface pin(OLB) of TCP 0.65 8.3 NO contamination, solder residue or solder balls on 1.5 product. 8.4 The IC on the TCP may not be damaged, circuits. 0.65 8.5 The residual rosin or tin oil of soldering (component or chip 1.5 component) is not burned into brown or black color. 8.6 08 General appearance Sealant on top of the ITO circuit has not hardened 1.5 8.7 Pin type must match type in specification sheet. 0.65 8.8 LCD pin loose or missing pins. 0.65 8.9 Product packaging must the same as specified on packaging 0.65 specification sheet. 8.10 Product dimension and structure must conform to product 0.65 specification sheet. Table 7. AZ DISPLAYS 19 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 11 RELIABILITY NO.. Description Test Condition Endurance test applying the high storage temperature for a long time 80ć,240 H Endurance test applying the low storage temperature for a long time -30ć,240H Endurance test applying the electric stress under high temperature for a long time 60ć,96H Endurance test applying the electric stress under low temperature for a long time -10ć,96H Endurance test applying the high temperature and high humidity storage for a long time 50ć,90% R.H 240H Endurance test applying electric stress under high temperature and high humidity for a long time 60ć, 90% R.H 96H 7 Temperature Cycle Endurance test applying the low and high temperature cycle -20ć 25ć 70ć 25ć 30min 5min 30min 5min one cycle -20ć/70ć 10 cycles 8 Vibration test Endurance test applying the vibration during transportation and using 10Hz~50Hz Swing:0.75mm time:30min 9 Fall test Endurance test dropping the LCM from a high place 600mm height 1 2 3 4 5 6 10 Test Item High temperature storage Low temperature storage High temperature operation Low temperature operation High temperature /humidity storage High temperature /humidity operation Static Endurance test applying static electric stress to Contact discharge: ±2KV~4KV electricity test terminal Air discharge: ±2KV~10KV Table 8. NOTE: TEST CONDITION (1) Temperature and humidity: If no specification, temp. set at 25±2°C, humidity set at 60±5%RH. (2) Operating state: Samples subject to the test shall be in “operating” condition. AZ DISPLAYS 20 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 12 USING LCD MODULES 12.1 LIQUID CRYSTAL DISPLAY MODULES LCD is composed of glass and polarizer. Pay attention to the following items when handling. (1) Please keep the temperature within specified range for use and storage. Polarization degradation, bubble generation or polarizer peel-off may occur with high temperature and high humidity. (2) Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass, tweezers, etc.). (3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors made of organic substances which will be damaged by chemicals such as acetone, toluene, ethanol and isopropylalcohol. (4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material like chamois soaked in petroleum benzin. Do not scrub hard to avoid damaging the display surface. (5) Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color fading. (6) Avoid contacting oil and fats. (7) Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizers. After products are tested at low temperature they must be warmed up in a container before coming is contacting with room temperature air. (8) Do not put or attach anything on the display area to avoid leaving marks on. (9) Do not touch the display with bare hands. This will stain the display area and degradate insulation between terminals (some cosmetics are determinated to the polarizers). (10) As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or rising. 12.2 PRECAUTION FOR HANDING LCD MODULES Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it. (1) Do not alter, modify or change the the shape of the tab on the metal frame. (2) Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached. (3) Do not damage or modify the pattern writing on the printed circuit board. (4) Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector. (5) Except for soldering the interface, do not make any alterations or modifications with a soldering AZ DISPLAYS 21 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 iron. (6) Do not drop, bend or twist LCM. (7) In order to avoid the cracking of the FPC,you should to pay attention to the area of FPC(R50mm) where the FPC was bent .the edge of coverlay;the area of surface of Ni-Au plating,the area of soldering land,the area of through hole. 12.3 ELECTRO-STATIC DISCHARGE CONTROL Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as for an ordinary CMOS IC. (1) Make certain that you are grounded when handing LCM. (2) Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body have the same electric potential. (3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak. (4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor. (5) As far as possible make the electric potential of your work clothes and that of the work bench the ground potential. (6) To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative humidity of 0%-60% is recommended. 12.4 PRECAUTIONS FOR OPERATION (1) Viewing angle varies with the change of liquid crystal driving voltage (VO). Adjust VO to show the best contrast. (2) Driving the LCD in the voltage above the limit shortens its life. (3) Response time is greatly delayed at temperature below the operating temperature range. However, this does not mean the LCD will be out of the order. It will recover when it returns to the specified temperature range. (4) If the display area is pushed hard during operation, the display will become abnormal. However, it will return to normal if it is turned off and then back on. (5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore, it must be used under the relative condition of 40°C , 50% RH. (6) When turning the power on, input each signal after the positive/negative voltage becomes stable. AZ DISPLAYS 22 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 Figure 16. 12.5 STORAGE When storing LCDs as spares for some years, the following precaution are necessary. (1) Store them in a sealed polyethylene bag. If properly sealed, there is no need for dessicant. (2) Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature between 0°C and 35°C. (3) The polarizer surface should not come in contact with any other objects. (We advise you to store them in the container in which they were shipped.) (4) Environmental conditions : - Do not leave them for more than 160hrs. at 70°C. - Should not be left for more than 48hrs. at -20°C. 12.6 SAFETY (1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. (2) If any liquid leakes out of a damaged glass cell and comes in contact with the hands, wash off thoroughly with soap and ater. 12.7 LIMITED WARRANTY Unless agreed between AZD and customer, AZD will replace or repair any of its LCD modules which are found to be functionally defective when inspected in accordance with AZD LCD modules acceptance standards (copies available upon request) for a period of one year from date of shipments. Cosmetic/visual defects must be returned to AZD within 90 days of shipment. Confirmation of such date shall be based on freight documents. The warranty liability of AZD limited to repair and/or replacement on the terms set forth above. AZD will not be responsible for any subsequent or consequential events. AZ DISPLAYS 23 ATM0350D2(AZ DISPLAYS) TFT MODULE VER2.2 12.8 RETURN LCM UNDER WARRANTY No warranty can be granted if the precautions stated above have been disregarded. The typical examples of violations are : - Broken LCD glass. - Circuit modified in any way, including addition of components. Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned with sufficient description of the failures or defects. Any connectors or cable installed by the customer must be removed completely without damaging the PCB’s eyelet, conductors and terminals. AZ DISPLAYS 24