AZ DISPLAYS SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY CUSTOMER APPROVAL ※ PART NO. : APPROVAL ATM0430D5-T(AZDISPLAYS) VER1.0 COMPANY CHOP CUSTOMER COMMENTS AZ DISPLAYS ENGINEERING APPROVAL DESIGNED BY CHECKED BY APPROVED BY ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 REVISION RECORD Date Rev.No. 2010.05.16 V1.0 AZ DISPLAYS Page Revision Items Prepared The first release 2 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 Contents 1. General Specifications ………………………………………………………………………………1 2. Pin Assignment ……………………………………………………………………………………...2 2.1. TFT LCD Panel Driving Section...................................................................................... 2 2.2. Touch Screen Panel Section............................................................................................ 4 3. Operation Specifications………………………………………………………………………………5 3.1. Absolute Maximum Ratings ............................................................................................ 5 3.2. Typical operation conditions ........................................................................................... 6 3.3 Backlight Driving Conditions .......................................................................................... 6 3.4. Power Sequence ............................................................................................................ 7 3.5. Timing Characteristics .................................................................................................... 8 3.5.1. Timing Conditions ................................................................................................... 8 3.5.2. Timing Diagram ...................................................................................................... 9 4. Touch Screen Panel Specifications ……………………………………………………………..10 4.1. Electrical Characteristics .............................................................................................. 10 4.2. Mechanical & Reliability Characteristics ........................................................................ 11 4.3. Linearity Definition ......................................................................................................... 12 4.4. Housing design guide ……………………………………………………………………………..13 5. Optical Specifications …………………………………………………………………………….....14 6. Reliability Test Items ……………………………………………………………………………….18 7. General Precautions ……………………………………………………………………………….19 7.1. Safety ............................................................................................................................ 19 7.2. Handling ........................................................................................................................ 19 7.3. Static Electricity.............................................................................................................. 19 7.4. Storage .......................................................................................................................... 19 7.5. Cleaning ........................................................................................................................ 19 8. Mechanical Drawing ……………………………………………………………………………….20 9. Package Drawing ……………………………………………………………………………….21 9.1. Packaging Material Table............................................................................................... 21 9.2. Packaging Quantity........................................................................................................ 21 9.3. Packaging Drawing........................................................................................................ 22 The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 3 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 1. General Specifications No. Item Specification 1 LCD size 4.3 inch(Diagonal) 2 Driver element a-Si TFT active matrix 3 Resolution 480 × 3 (RGB) × 272 4 Display mode Normally White, Transmissive 5 Dot pitch 0.066(W) × 0.198(H) mm 6 Active area 95.04(W) × 53.856(H) mm 7 Module size 105.5(W) × 67.2(H) × 4.05(D) mm 8 Surface treatment Anti-Glare 9 Color arrangement RGB-stripe 10 Interface Digital 11 Backlight Power consumption 0.558 W(Typ.) 12 Panel Power consumption 0.056 W (Typ.) 13 Weight TBD (Typ.) Remark Note 1 Note 1: Refer to Mechanical Drawing. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 4 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 2. Pin Assignment 2.1.TFT LCD Panel Driving Section FPC Connector is used for the module electronics interface. The recommended model is “FH19SC-40S-0.5SH” manufactured by HIROSE. Pin No. Symbol I/O Function 1 VLED- P Power for LED backlight cathode 2 VLED+ P Power for LED backlight anode 3 GND P Power ground 4 VDD P Power voltage 5 R0 I Red data (LSB) 6 R1 I Red data 7 R2 I Red data 8 R3 I Red data 9 R4 I Red data 10 R5 I Red data 11 R6 I Red data 12 R7 I Red data (MSB) 13 G0 I Green data (LSB) 14 G1 I Green data 15 G2 I Green data 16 G3 I Green data 17 G4 I Green data 18 G5 I Green data 19 G6 I Green data 20 G7 I Green data (MSB) Remark The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 5 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 21 B0 I Blue data (LSB) 22 B1 I Blue data 23 B2 I Blue data 24 B3 I Blue data 25 B4 I Blue data 26 B5 I Blue data 27 B6 I Blue data 28 B7 I Blue data (MSB) 29 GND P Power ground 30 CLK I Pixel clock 31 DISP I Display on/off 32 NC - No connection 33 NC - No connection 34 DE I Data Enable 35 NC - No connection 36 GND P Power ground 37 X1 I/O Right electrode – differential analog 38 Y1 I/O Bottom electrode – differential analog 39 X2 I/O Left electrode – differential analog 40 Y2 I/O Top electrode – differential analog I: input, O: output, P: Power The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 6 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 2.2. Touch Screen Panel Section Pin No. Symbol I/O Function Remark 1 X1 Right 2 Y1 Bottom 3 X2 Left Left electrode – differential analog 4 Y2 Top Top electrode – differential analog Right electrode – differential analog Bottom electrode – differential analog Note: Touch Screen Panel Block Top View The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 7 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 3. Operation Specifications 3.1. Absolute Maximum Ratings (Note 1) Values Item Symbol Unit Remark Min. Max. VDD -0.5 5.0 V Logic input -0.5 5.0 V Operation temperature TOP -20 70 ℃ Note 3, 4 Storage temperature TST -30 80 ℃ Note 3, 4 LED Reverse Voltage VR - 1.2 V Each LED Note 2 LED Forward Current IF - 25 mA Each LED Power voltage Input signal voltage Note 1: The absolute maximum rating values of this product are not allowed to be exceeded at any times. A module should be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme condition, the module may be permanently destroyed. Note 2: VR Conditions: Zener Diode 20mA Note 3: 90% RH Max. (Max wet temp. is 60℃) Maximum wet-bulb temperature is at 60℃ or less. And No condensation (no drops of dew) +60℃ ℃, 90%RH (℃) Note 4: In case of temperature below 0℃,the response time of liquid crystal (LC) becomes slower and the color of panel darker than normal one. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 8 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 3.2. Typical operation conditions Values Item Symbol Unit Min. Typ. Max. Power voltage VDD 3.1 3.3 3.5 V Current for Driver IVDD - 17 25 mA Input logic high voltage VIH 0.8VDD - VDD V Remark VDD = 3.3V Note 1 Input logic low voltage VIL GND - 0.2VDD V Note1: CLK, DE, R0~ R7, G0~ G7, B0~ B7. 3.3 Backlight Driving Conditions Values Item Symbol Unit Min. Typ. Max. Voltage for LED Backlight VL 25.2 27.9 31.5 V Current for LED Backlight IL 18 20 22 mA LED life time - 20,000 - - Hr Remark Note 2 Note 1 Note 1: The “LED life time” is defined as the module brightness decrease to 50% original brightness that the ambient temperature is 25℃ and IL =20mA. The LED lifetime could be decreased if operating IL is lager than 20 mA. Note 2: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and IL =20mA. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 9 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 3.4. Power Sequence To prevent a latch-up or DC operation of the LCD module, the power on/off sequence should be as the diagram below. Symbol Specification Symbol Specification T1 0≦T1≦10 msec T4 160 msec ≦T4 T2 0≦T2≦100 msec T5 160 msec ≦T5 T3 0≦T3≦200 msec T6 1 msec ≦T6 The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 10 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 3.5. Timing Characteristics 3.5.1. Timing Conditions Parallel DE mode RGB input timing table Value Parameter Symbol Unit Min. Typ. Max. CLK frequency fclk 7 9 12 MHz DEV period time Tv 277 288 400 H DEV display area Tvd DEV blanking Tvb 5 16 128 H DEH period time Th 520 525 800 CLK DEH display area Thd DEH blanking Thb 40 45 320 CLK CLK cycle time Tclk 83 110 143 ns Clock width of high level Tcwh 40 50 60 % Clock width of low level Tcwl 40 50 60 % Clock rising time trck - 9 ns Clock falling time tfck - 9 ns Data Setup Time tdesu 10 - - ns Data Hold Time tdahd 10 - - ns DE Setup Time tdesu 10 - - ns DE Hold Time tdehd 10 - - ns 272 H 480 CLK The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 11 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 3.5.2. Timing Diagram The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 12 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 4. Touch Screen Panel Specifications 4.1. Electrical Characteristics Value Item Unit Remark Min. Typ. Max. -1.5 - 1.5 % Analog X and Y directions 300 - 1500 Ω X 100 - 900 Ω Y 25 - - MΩ Voltage - 5 7 V Chattering - - 10 ms 100kΩ pull-up 80 - - % JIS K7105 Linearity Terminal Resistance Insulation resistance Transparency DC 25V DC Note: Avoid operating with hard or sharp material such as a ball point pen or a mechanical pencil except a polyacetal pen (tip R0.8mm or less) or a finger. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 13 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 4.2. Mechanical & Reliability Characteristics Value Item Activation force Durability-surface scratching Durability-surface pitting Surface hardness Unit Remark Min. Typ. Max. 80 - - gf Note 1 Write 100,000 - - characters Note 2 1,000,000 - - touches Note 3 3 - - H JIS K5400 Note 1: Activation force test condition (1) Input DC 5V on X direction, Drop off Polyacetal Stylus (R0.8), until output voltage stabilize ,then get the activation force。 (2) R8.0mm Silicon rubber for finger Activation force test (3) Test point: 9 points Note 2: Measurement for surface area. -Scratch 100,000 times straight line on the film with a stylus change every 20,000 times. -Force: 250gf. -Speed: 60mm/sec. -Stylus: R0.8 polyacetal tip. Note 3: Pit 1,000,000 times on the film with a R0.8 silicon rubber. -Force: 250gf. -Speed: 2times/sec. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 14 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 4.3. Linearity Definition Va: maximum voltage in the active area of touch panel Vb: minimum voltage in the active area of touch panel X: random measuring point Vxm: actual voltage of Lx point Vxi: theoretical voltage of Lx point Linearity = [|Vxi-Vxm |/(Va-Vb)]*100% Note: Test area is as follows and operation force is 150gf. 2.0mm 2.0mm Active Area Test Area 2.0mm 2.0mm The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 15 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 4.4. Housing design guide Housing design follow as below 1) Avoid the design that housing overlap and press on the active area of the LCM 2) Give enough gap(over 0.5mm at compressed) between the housing and TSP to protect wrong operating. 3) Use a buffer material(Gasket) between the TSP and housing to protect damage and wrong operating 4) Avoid the design that buffer material overlap and press on the inside of TSP view area. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 16 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 5. Optical Specifications Values Item Viewing angle (CR≥ 10) Symbol Condition Unit Min. Typ. Max. θL Φ=180°(9 o’clock) 60 70 - θR Φ=0°(3 o’clock) 60 70 - Remark degree Note 1 Note 7 θT Φ=90°(12 o’clock) 40 50 - θB Φ=270°(6 o’clock) 60 70 - TON - 10 20 msec Note 3 TOFF - 15 30 msec Note 3 CR 400 500 - - Note 4 0.26 0.31 0.36 - WY 0.28 0.33 0.38 - Note 2 Note 5 Note 6 Note 7 Luminance L 350 400 - cd/m² Note 6 Luminance uniformity YU 70 75 - % Note 8 Response time Contrast ratio WX Normal θ=Φ=0° Color chromaticity Test Conditions: 1. VDD=3.3V, IL=20mA (Backlight current), the ambient temperature is 25℃. 2. The test systems refer to Note 2. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 17 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 Note 1: Definition of viewing angle range Normal line θ=Φ=0° Φ=90° 12 o’clock direction θL θB θR θT Φ=180° Φ=0° Active Area Φ=270° 6 o’clock direction Fig. 4-1 Definition of viewing angle Note 2: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/Field of view: 1° /Height: 500mm.) Photo detector 500mm Normal line θ=Φ=0° Φ=90° 12 o’clock direction Φ=0° Φ=180° Active Area Φ=270° 6 o’clock direction Fig. 4-2 Optical measurement system setup The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 18 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 Note 3: Definition of Response time The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from 10% to 90%. Photo detector output (Relative value) White (TFT OFF) Black (TFT ON) White (TFT OFF) 100% 90% 10% 0% TON TOFF Fig. 4-3 Definition of response time Note 4: Definition of contrast ratio Contrast ratio (CR) = Luminance measured when LCD on the " White" state Luminance measured when LCD on the " Black" state Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel. The LED driving condition is IL=20mA. Note 7: The values shall be measured without Touch Screen Panel. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 19 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 Note 8: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each measuring area. Luminance Uniformity (Yu) = L-------Active area length B min B max W----- Active area width L/6 L/3 L/3 W/3 W W/3 W/6 L Fig. 4-4 Definition of measuring points Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 20 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 6. Reliability Test Items (Note3) Item Test Conditions Remark High Temperature Storage Ta = 80℃ 240 hrs Note 1,Note 4 Low Temperature Storage Ta = -30℃ 240hrs Note 1,Note 4 High Temperature Operation Ts = 70℃ 240hrs Note 2,Note 4 Low Temperature Operation Ta = -20℃ 240hrs Note 1,Note 4 Operate at High Temperature and Humidity +60℃, 90%RH 240 hrs Note 5 Thermal Shock -30℃/30 min ~ +80℃/30 min for a total 100 cycles, Start with cold temperature and end with high temperature Note 4 Frequency range:10~55Hz Stroke:1.5mm Vibration Test Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X. Y. Z. (6 hours for total) 100G 6ms,±X, ±Y, ±Z 3 times for each Mechanical Shock direction Random Vibration : 0.015G*G/Hz from 5-200HZ, Package Vibration Test -6dB/Octave from 200-500HZ 2 hours for each direction of X. Y. Z. (6 hours for total) Height:60 cm Package Drop Test 1 corner, 3 edges, 6 surfaces ± 2KV, Human Body Mode, Electro Static Discharge 100pF/1500Ω Note 1: Ta is the ambient temperature of samples. Note 2: Ts is the temperature of panel’s surface. Note 3: In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guarantees operation, but doesn’t guarantee all the cosmetic specification. Note 4: Before cosmetic and function tests, the product must have enough recovery time, at least 2 hours at room temperature. Note 5: Before cosmetic and function tests, the product must have enough recovery time, at least 24 hours at room temperature. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 21 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 7. General Precautions 7.1. Safety Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your skin or clothes, wash it off immediately by using soap and water. 7.2. Handling 1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or to excessive force on its surface. 2. The polarizer attached to the display is easily damaged. Please handle it carefully to avoid scratch or other damages. 3. To avoid contamination on the display surface, do not touch the module surface with bare hands. 4. Keep a space so that the LCD panels do not touch other components. 5. Put cover board such as acrylic board on the surface of LCD panel to protect panel from damages. 6. Transparent electrodes may be disconnected if you use the LCD panel under environmental conditions where the condensation of dew occurs. 7. Do not leave module in direct sunlight to avoid malfunction of the ICs. 7.3. Static Electricity 1. Be sure to ground module before turning on power or operating module. 2. Do not apply voltage which exceeds the absolute maximum rating value. 7.4. Storage 1. Store the module in a dark room where must keep at 25±10℃ and 65%RH or less. 2. Do not store the module in surroundings containing organic solvent or corrosive gas. 3. Store the module in an anti-electrostatic container or bag. 7.5. Cleaning 1. Do not wipe the polarizer with dry cloth. It might cause scratch. 2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals might permanent damage to the polarizer. The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 22 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 8. Mechanical Drawing The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 23 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 9. Package Drawing 9.1. Packaging Material Table No. Item 1 LCM Module 2 Partition 3 4 5 Model (Material) Corrugated Bar Dust-Proof Bag Corrugated ATM0430D5-T BC Corrugated paper BC Corrugated paper PE BC Corrugated Dimensions (mm) Unit Weight (kg) Quantity (pcs) 105.5 × 67.2 × 4.05 TBD 160 512 × 349 × 106 1.102 2 349 × 173 0.030 8 700 × 530 0.060 1 510 × 343 0.130 2 1152 × 512 0.260 1 Board-1 Paper Corrugated BC Corrugated Board-2 Paper 7 A/S Bag PE 132 × 117 0.002 160 8 Carton Co rru ga t e d pap e r 530 × 355 × 255 1.100 1 9 Total weight 6 Remark TBD 9.2. Packaging Quantity (1) LCM quantity per Partition: 2Rows x 40quantity per Row = 80 pcs (2) Total LCM quantity in Carton: 2 layer x 80 pcs per Partition = 160 pcs The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 24 ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0 CHIMEI INNOLUX SPEC NO.: A043-24-TT-71 Date : 2010/04/19 9.3. Packaging Drawing The copyright belongs to InnoLux. Any unauthorized use is prohibited. AZ DISPLAYS 25