Document 288-1 Chip Inductors – 0805LS (2012) These ferrite core surface mount inductors have lower DCR and higher current ratings than our 0805CS Series. They come in inductance values from 0.078 to 27 µH. Coilcraft Designer’s Kit C354 contains samples of all 5% inductance tolerance parts. To order, contact Coilcraft or visit http://order.coilcraft.com to purchase on-line. Inductance2 Irms6Color Percent SRF min4 DCR max5 Q min3 (MHz) (Ohms) (A)code Part number1 (µH)tolerance 0805LS-78NX_L_ 0.078 @ 7.9 MHz 0805LS-111X_L_ 0.110 @ 7.9 MHz 0805LS-471X_L_ 0.470 @ 7.9 MHz 0805LS-681X_L_ 0.680 @ 7.9 MHz 0805LS-102X_L_ 1.0 @ 7.9 MHz 0805LS-122X_L_ 1.2 @ 7.9 MHz 0805LS-152X_L_ 1.5 @ 7.9 MHz 0805LS-182X_L_ 1.8 @ 7.9 MHz 0805LS-222X_L_ 2.2 @ 7.9 MHz 0805LS-272X_L_ 2.7 @ 7.9 MHz 0805LS-332X_L_ 3.3 @ 7.9 MHz 0805LS-392X_L_ 3.9 @ 7.9 MHz 0805LS-472X_L_ 4.7 @ 7.9 MHz 0805LS-682X_L_ 6.8 @ 7.9 MHz 0805LS-822X_L_ 8.2 @ 2.5 MHz 0805LS-103X_L_ 10.0 @ 2.5 MHz 0805LS-153X_L_ 15.0 @ 2.5 MHz 0805LS-223X_L_ 22.0 @ 2.5 MHz 0805LS-273X_L_ 27.0 @ 2.5 MHz 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 19 @ 7.9 MHz 19 @ 7.9 MHz 19 @ 7.9 MHz 20 @ 7.9 MHz 20 @ 7.9 MHz 15 @ 7.9 MHz 20 @ 7.9 MHz 20 @ 7.9 MHz 20 @ 7.9 MHz 20 @ 7.9 MHz 20 @ 7.9 MHz 20 @ 7.9 MHz 20 @ 7.9 MHz 20 @ 7.9 MHz 18 @ 2.5 MHz 18 @ 2.5 MHz 18 @ 2.5 MHz 18 @ 2.5 MHz 15 @ 2.5 MHz 1440 1200 500 400 340 280 275 246 106 105 83 52 50 35 27 21 17 13 11 0.042 0.05 0.31 0.46 0.69 1.20 1.03 1.15 1.28 1.48 1.57 1.70 1.87 2.25 2.55 3.45 5.03 6.18 11.04 2.0 2.0 0.720 0.590 0.500 0.400 0.490 0.410 0.365 0.350 0.330 0.300 0.280 0.260 0.250 0.200 0.180 0.150 0.120 Black Brown Red Orange Yellow Brown Green Blue Brown Violet Gray White Black Brown Red Orange Yellow Green Blue 1. When ordering, specify tolerance, termination and packaging codes: Core material Ceramic/Ferrite 0805LS-273XJLC Tolerance: G=2% J = 5% (Table shows stock tolerances in bold.) Termination:L=RoHS compliant silver-palladium-platinum-glass frit. E=Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging:C =7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. 2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/ HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Q measured on an Agilent/HP 4291A with an Agilent/HP 16193 test fixture. 4. SRF measured using an Agilent/HP 8753D network analyzer with a Coilcraft SMD-D test fixture. 5. DCR measured on a Cambridge Technology Micro-ohmmeter. 6. Current that causes a 15°C temperature rise from 25°C ambient. Because of their open construction, these parts will not saturate. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Environmental RoHS compliant, halogen free optional Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 12.7 – 13.9 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +100°C with derated current Storage temperature Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +100 to +250 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 2000/7″reel; Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.6 mm pocket depth PCB washing Only pure water or alcohol recommended US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 288-1 Revised 01/18/12 © Coilcraft Inc. 2012 This product may not be used in medical of high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check out web site for latest information. Document 288-2 0805LS Series Chip Inductors Typical L vs Frequency Typical Q vs Frequency 100 35 27 µH 10 3.3 µH 25 3.3 µH 10 µH Q factor Inductance (µH) 30 10 µH 1 µH 1 0.110 µH 0.1 20 0.110 µH 27 µH 15 1 µH 10 5 0.01 0.1 10 1 0 100 Frequency (MHz) Irms Derating 10 H C Pick and place material F G A 110 100 F I D E terminal 70 I J 90 80 100 Frequency (MHz) B overall 120 Terminal wraparound: approx 0.010/0,25 both ends Recommended Land Pattern 60 ABCD maxmaxmax ref E F G H IJ 0.0900.0750.0630.0200.0500.0200.0400.0700.0400.030inches 2,291,911,600,511,270,511,021,781,020,76 mm 50 40 30 Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm. 25°C Percent of rated Irms 1 0.1 20 10 0 -40 -20 0 20 40 60 80 100 120 Ambient temperature (°C) US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 288-2 Revised 01/18/12 © Coilcraft Inc. 2012 This product may not be used in medical of high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check out web site for latest information.