PRODUCT DATASHEET Strada-FW series Ordering number C12086 Description C12086-Strada-FW-XP-G Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Strada-Forward Lens XP-G Transparent 15.4 x 19.6 mm 10.8 mm Rectangular PMMA Glue Ready FWHM Efficiency cd/lm Gerber File Asym degrees 92 % Available http://www.ledil.fi/Strada-F_Fully_Asymmetrical_Forward_Throw Ordering number CA12087 Description CA12087-Strada-FW-Tape-XP-G Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Strada-Forward Lens XP-G Transparent 15.4 x 19.6 mm 10.8 mm Rectangular PMMA Tape Ready FWHM Efficiency cd/lm Gerber File Asym degrees 92 % Available http://www.ledil.fi/Strada-F_Fully_Asymmetrical_Forward_Throw NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. October 6th 2011 23:35 Copyright Ledil Oy - Subject to change without prior notice - Page 1/3 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: [email protected] FAX: +358-2-733 8001 PRODUCT DATASHEET Strada-FW series GENERAL INFORMATION - Product series especially designed & optimized for XP-G series of LEDs. - Special care taken to make light distribution as uniform as possible. - Lens material optical grade PMMA with high UV and temperature resistance (105 degrees of Celcius / 220 degrees of Fahrenheit). Allows use of high current and temperature conditions. Please find more information about used material from below: http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20UL94_Yellow%20Card.pdf http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20PLEXIGLAS-Datasheet.pdf - Fastening to heat sink with a PU foam adhesive tape of automotive grade. Please find fastening details by clicking link: http://www.ledil.com/datasheets/DataSheet_TAPE.pdf - Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glue options. http://www.ledil.com/datasheets/DataSheet_GLUES.pdf NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. NOTE 2: Assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. Slanted assembly might cause unbalanced bond to the surface. All surfaces where tape is applied must be clean, dry and free from grease and dirt. If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED manufacturer - this is important as cleaning shall under no circumstances damage LEDs or other electronics components on the PCB. Further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED manufacturer -this is important as cleaning shall under no circumstances damage LEDs or other electronics components on the PCB. Further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. October 6th 2011 23:35 Copyright Ledil Oy - Subject to change without prior notice - Page 2/3 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: [email protected] FAX: +358-2-733 8001 PRODUCT DATASHEET Strada-FW series C12086 CA12087 October 6th 2011 23:35 Copyright Ledil Oy - Subject to change without prior notice - Page 3/3 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: [email protected] FAX: +358-2-733 8001 A B C D c/c 8.6 4 4 2 1 3 10.8 3 20 15.4 c/c 2 3.2 MATERIALS Lens: PMMA tape: Pu foam with PSA This drawing is our property. It can't be reproduced or communicated without our written agreement. 1 DRAWN BY pv DATE ah DATE 22.8.2011 DESIGNED BY hh DATE 22.8.2011 D 2 19.6 Ledil Oy Salorankatu 10 24240 SALO Finland DRAWING TITLE Datasheet Strada-FW assy 23.8.2011 CHECKED BY Top view Scale: 2:1 SIZE DRAWING NUMBER CA12087 A4 SCALE REV 2:1 WEIGHT(g) 1 SHEET A 1/1 1