Technical Data Sheet 0805 Package Chip LED (0.8mm Height) 17-215/S2C-AQ1R2B/3T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain with in RoHS compliant version Descriptions ․The 17-215 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 17-215/S2C-AQ1R2B/3T Chip Material AlGaInP Emitted Color Resin Color Brilliant Orange Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Rev.1 Page: 1 of 10 Prepared by: Chao DaiJian 17-215/S2C-AQ1R2B/3T Package Outline Dimensions Note: The tolerances unless mentioned are ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Rev.1 Page: 2 of 10 Prepared by: Chao DaiJian 17-215/S2C-AQ1R2B/3T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Power Dissipation Pd 60 mW Electrostatic Discharge(HBM) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 72.0 ----- 180 mcd Viewing Angle 2θ1/2 ----- 130 ---- deg Peak Wavelength λp ---- 611 ---- nm Dominant Wavelength λd 600.5 ---- 612.5 nm Spectrum Radiation Bandwidth △λ ----- 17 ---- nm Forward Voltage VF 1.75 ---- 2.35 V Reverse Current IR ---- ---- 10 µA Condition IF =20mA VR=5V Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Rev.1 Page: 3 of 10 Prepared by: Chao DaiJian 17-215/S2C-AQ1R2B/3T Bin Range Of Luminous Intensity Bin Min Max Q1 72.0 90.0 Q2 90.0 112 R1 112 140 R2 140 180 Unit Condition mcd IF =20mA Unit Condition nm IF =20mA Bin Range Of Dom. Wavelength Group A Bin Min Max D8 600.5 603.5 D9 603.5 606.5 D10 606.5 609.5 D11 609.5 612.5 Bin Range Of Luminous Voltage Group B Bin Min Max 0 1.75 1.95 1 1.95 2.15 2 2.15 2.35 Unit Condition V IF =20mA Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Rev.1 Page: 4 of 10 Prepared by: Chao DaiJian 17-215/S2C-AQ1R2B/3T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Rev.1 Page: 5 of 10 Prepared by: Chao DaiJian 17-215/S2C-AQ1R2B/3T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Rev.1 Page: 6 of 10 Prepared by: Chao DaiJian 17-215/S2C-AQ1R2B/3T Carrier Tape Dimensions: Loaded quantity 3000PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Label Rev.1 Page: 7 of 10 Prepared by: Chao DaiJian 17-215/S2C-AQ1R2B/3T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 2 Temperature Cycle 3 Thermal Shock 4 5 High Temperature Storage Low Temperature Storage Test Sample Hours/Cycles Size Ac/Re 6 Min. 22 PCS. 0/1 300 Cycles 22 PCS. 0/1 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 H : +100℃ 15min ∫ 5 min L : -40℃ 15min H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85% RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Rev.1 Page: 8 of 10 Prepared by: Chao DaiJian 17-215/S2C-AQ1R2B/3T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Rev.1 Page: 9 of 10 Prepared by: Chao DaiJian 17-215/S2C-AQ1R2B/3T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE- Prepared date: 1-july-2011 Rev.1 Page: 10 of 10 Prepared by: Chao DaiJian