EVERLIGHT 17-21-GVC-AMPB-3T

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
0805 Package Chip LED(1.1mm Height)
17-21/GVC-AMPB/3T
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
․The product itself will remain within RoHS compliant version.
Descriptions
․The 17-21 SMD Taping is much smaller than lead
frame type components, thus enable smaller board
size, higher packing density, reduced storage space
and finally smaller equipment to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
․Indoor signboard use.
Device Selection Guide
Part No.
17-21/GVC-AMPB/3T
Chip
Material
Emitted Color
AlGaInP
Green
Lens Color
Water Clear
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 1 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan
EVERLIGHT ELECTRONICS CO.,LTD.
17-21/GVC-AMPB/3T
Package Outline Dimensions
-
1.05
+
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 2 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan
EVERLIGHT ELECTRONICS CO.,LTD.
17-21/GVC-AMPB/3T
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
25
mA
IFP
60
mA
Power Dissipation
Pd
60
mW
Electrostatic Discharge
ESD
2000
V
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +90
℃
Soldering Temperature
Tsol
Peak Forward Current
(Duty 1/10 @1KHz)
Reflow Soldering:260 ℃ for 10 sec
Hand Soldering:350℃ for 3 sec
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Luminous Intensity
Iv
18.0
-----
72.0
mcd
Viewing Angle
2θ1/2
----
140
----
deg
Peak Wavelength
λp
----
568
----
nm
Dominant Wavelength
λd
563.5
----
571.5
nm
Spectrum Radiation
Bandwidth
△λ
----
20
----
nm
Forward Voltage
VF
1.75
----
2.35
V
Reverse Current
IR
----
----
10
μA
Condition
IF=20mA
VR=5V
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.1V
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 3 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan
EVERLIGHT ELECTRONICS CO.,LTD.
17-21/GVC-AMPB/3T
Bin Range Of Dom. Wavelength
Groups
A
Bin
Min
Max
C13
563.5
565.5
C14
565.5
567.5
C15
567.5
569.5
C16
569.5
571.5
Unit
Condition
nm
IF=20mA
Unit
Condition
mcd
IF=20mA
Unit
Condition
nm
IF=20mA
Bin Range Of Luminous Intensity
Bin
Min
Max
M
18.0
28.5
N
28.5
45.0
P
45.0
72.0
Bin Range Of Forward Voltage
Groups
B
Bin
Min
Max
0
1.75
1.95
1
1.95
2.15
2
2.15
2.35
Notes:
1.Tolerance of Luminous Intensity ±15%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.1V
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 4 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan
EVERLIGHT ELECTRONICS CO.,LTD.
17-21/GVC-AMPB/3T
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 5 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan
EVERLIGHT ELECTRONICS CO.,LTD.
17-21/GVC-AMPB/3T
Label explanation
CAT: Luminous Intensity (mcd)
HUE: Dom. Wavelength (nm)
xxxxxx
xxxxxx
REF: Forward Voltage (V)
RoHS
xxxxxxxxxxxx
xxxx
xxxxxxxx
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm,Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 6 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan
EVERLIGHT ELECTRONICS CO.,LTD.
17-21/GVC-AMPB/3T
Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm , Unit = mm
Moisture Resistant Packaging
Label
Aluminum moistue-proof bag
Desiccant
Label
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 7 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan
EVERLIGHT ELECTRONICS CO.,LTD.
17-21/GVC-AMPB/3T
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level : 90 %
LTPD : 10 %
Test
Sample
No.
Items
Test Condition
Hours/Cycles
Size
Temp. : 260℃±5℃
1
Reflow Soldering
22 PCS.
6 Min.
Min. 5sec.
2
3
4
5
Ac/Re
0/1
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles
22 PCS.
0/1
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles
22 PCS.
0/1
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
High Temperature
Storage
Low Temperature
Storage
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/ 85%RH
1000 Hrs.
22 PCS.
0/1
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 8 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan
EVERLIGHT ELECTRONICS CO.,LTD.
17-21/GVC-AMPB/3T
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift
will cause big current change ( Burn out will happen ).
2. Storage time
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 9 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan
EVERLIGHT ELECTRONICS CO.,LTD.
17-21/GVC-AMPB/3T
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of the
hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 10 of 10
Device No. : SZDSE-171-G29
Prepared date:14-Oct-2006
Prepared by: Zhifang Pan