HS1AL thru HS1ML SURFACE MOUNT HIGH EFFICIENCY (ULTRA FAST) GLASS PASSIVATED RECTIFIERS REVERSE VOLTAGE - 50 to 1000 Volts FORWARD CURRENT - 1.0 Ampere SOD-123FL FEATURES ● Low cost .114(2.9) .098(2.5) ● Diffused junction ● Low reverse leakage current .077(1.95) .061(1.55) ●Ultra fast switching for high efficiency .039(1.0) .024(0.6) ● Low forward voltage drop ● High current capability ● The plastic material carries UL recognition 94V-0 MECHANICAL DATA .047(1.2) .031(0.8) ●Case: JEDEC SOD-123FL molded plastic body over glass passivated chip .043(1.1) .020(0.5) .154(3.9) .138(3.5) .010(0.25) .002(0.05) ●Terminals: Solder plated, solderable per J-STD-002B and JESD22-B102D ●Polarity: Laser band denotes cathode end ●Weight: 0.017gram .004(0.1)max Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25℃ ambient temperature unless otherwise specified. Single phase, half wave ,60Hz, resistive or inductive load. For capacitive load, derate current by 20% SYMBOL HS1AL HS1BL HS1DL HS1GL HS1JL HS1KL HS1ML MARKING H1AL H1BL H1DL H1GL H1JL H1KL H1ML Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 V VDC 50 100 200 400 600 800 1000 V CHARACTERISTICS Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TA=55 ℃ UNIT I(AV) 1.0 A IFSM 25 A Peak Forward Surge Current 8.3ms Single Half Sine-Wave Super Imposed on Rated Load(JEDEC Method) Peak Forward Voltage at 1.0A DC 1.0 VF Maximum DC Reverse Current @TJ=25℃ at Rated DC Blocking Voltage @TJ=100℃ Maximum Reverse Recovery Time(Note 1) Typical Junction Capacitance (Note2) Typical Thermal Resistance (Note3) Operating Temperature Range Storage Temperature Range 1.3 1.7 5.0 IR μA 100 50 TRR V 75 nS CJ 9 pF RθJA 180 ℃/W TJ -55 to +150 ℃ TSTG -55 to +150 ℃ NOTES: 1.Measured with IF=0.5A,IR=1A,IRR=0.25A. 2.Measured at 1.0 MHz and applied reverse voltage of 4.0V DC 3.Thermal resistance junction to ambient. REV. 1, 30-Dec-2011 ~ 110 ~ RATING AND CHARACTERTIC CURVES HS1AL thru HS1ML FIG. 2 – MAXIMUM NON-REPETITIVE SURGE CURRENT FIG. 1 – FORWARD CURRENT DERATING CURVE PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT AMPERES 1.0 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.8 0.6 0.4 0.2 0 25 50 75 100 125 150 40 30 20 10 PULSE WIDTH 8.3ms SINGLE HALF-SINE-WAVE (JEDEC METHOD) 0 1 175 2 20 50 100 NUMBER OF CYCLES AT 60Hz AMBIENT TEMPERATURE (℃) FIG.3 – TYPICAL JUNCTION CAPACITANCE FIG.4-TYPICAL FORWARD CHARACTERISTICS 100 10 INSTANTANEOUS FORWARD CURRENT, (A) CAPACITANCE (pF) 10 5 10 T J = 25°C f = 1 MHz 1 1 4 10 H1AL - H1DL 1.0 H1GL H1JL - H1ML 0.1 T J = 25°C PULSE WIDTH 300us 0.01 0 100 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE,VOLTS REVERSE VOLTAGE ,VOLTS REV. 1, 30-Dec-2011 ~ 111 ~