Si 4 7 7 x - EVB S i477 X E VALUATION B OAR D U SER ’ S G UIDE Description Features The Si477x EVB is a platform designed to simplify evaluation and development with the Silicon Laboratories Si477x series tuners. The platform includes both hardware and software tools to easily configure and operate the tuner. This guide contains the following information: Quick Start Guide: Three quick steps to set up your board and tune a station Kit Contents: Components included in the kit Software/GUI Guide: Installation and usage of the evaluation GUI Hardware Guide: Description, configuration, and design files for baseboard and daughtercards Complete antenna-to-audio evaluation system Intuitive software interface supports simple evaluation to detailed performance testing Flexible hardware interface for evaluation and prototyping of various RF front end circuit options Portable operation facilitates field measurements with only a PC Headphone Buffered L / R / MPX Direct Out Functional Block Diagram Microcontroller Power Supplies Si477x Tuner Daughter Card test points Analog Audio USB Rev. 0.3 6/12 Copyright © 2012 by Silicon Laboratories PC GUI Si477x-EVB Si477x-EVB 1. Introduction Thank you for purchasing the Silicon Laboratories Si477x Evaluation Kit. This kit includes hardware and software tools to facilitate evaluation and development with the Si477x AM/FM Tuner family. Figure 1. Si477x Evaluation Board Register at www.silabs.com for additional application notes, articles, and other support resources. 2 Rev. 0.3 Si477x-EVB 2. Kit Contents 2.1. Si477x-EVB Evaluation Board All material and information contained in the enclosure is confidential and covered under non-disclosure agreement (NDA). Quark baseboard (1) Si477x Rev 2.0 and later daughtercard (1) USB cable (1) BNC to RCA adapters (2) RCA cable (1) Loop antenna (1) BNC to SMA adapter (1) Headphones (1) 9 V universal adapter (1) Documentation and software CD including the following: Si477x-EVB User's Guide GUI Software and Example Code Microsoft.net Framework for use with the Development GUI AN645: Si477x Programming Guide Si477x Release Notes Development 2.2. Si4770Module-A-EVB Module Kit Separately from the Si477x-EVB kit, user's may also order an Si4770Module-A-EVB kit. All material and information contained in the enclosure is confidential and covered under non-disclosure agreement (NDA). 4-Layer Si477x Si4770 Module Rev1.0 Interposer Rev1.0 card Rev. 0.3 3 Si477x-EVB 3. Quick-Start Guide This section gives three quick steps to get your evaluation kit installed and running. Refer to the following sections for additional details on configuring and using the kit. 3.1. Install the Software Insert the CD. Open the file Start_Here.htm. Click on the link to the GUI. Run setup.exe. 3.2. Connect the Board Configure the PCB for USB as the power source: Slide switch to "USB". Place four jumpers between "LDO" and "TNR" positions. Figure 2. Selecting USB Power Source Connect headphones or powered speakers to the HEADPHONE_OUT jack. Figure 3. Audio Output Connection 4 Rev. 0.3 Si477x-EVB Connect an AM loop antenna or FM whip antenna to the tuner daughtercard using the appropriate connection. For conducted tests, a signal source may be connected to AM or FM using the appropriate SMA connectors. Figure 4. Antenna Connections Rev. 0.3 5 Si477x-EVB 3.3. Listen Launch Select the GUI from the desktop shortcut: FM receive mode, click Initialize: Figure 5. Initialization Window Tune a station by entering the frequency or dragging the tuning slider. Decrease the volume by dragging the Volume slider. Figure 6. FM Receiver Window 6 Rev. 0.3 Si477x-EVB 4. Software The Si477x Evaluation Kit includes a graphical user interface (GUI) to simplify tuner evaluation and configuration. This utility is useful both for demonstrations and for fine-tuning the various tuner properties and modes before coding firmware in the target system. The GUI is designed for Windows XP and later. 4.1. Installation The software installation has two components: the GUI and the Microsoft.NET Framework. The board communicates via a USB HID interface, so no additional hardware drivers are needed. Install the software components by the following steps: 1. Locate the installation software: a. Open a window to the installation CD. b. Open the software folder. 2. Install the software: a. Start setup.exe. b. Follow the on-screen prompts. Notes: You may receive an error stating: "This setup requires the .NET Framework version 4.0." If so, install the .NET version provided on the CD (dotnetfx.exe). Important, release-specific notes may be included in the Readme.doc file. Please review this before finalizing the installation. Register at the Broadcast Audio Customer Support Page at www.silabs.com. All supporting documentation including data sheets, application notes, example code, and important layout guidelines are available only through the support site. Silicon Labs periodically updates versions of the content above and posts them there. All materials are covered under NDA. Rev. 0.3 7 Si477x-EVB 4.2. Initialization The Silicon Labs GUI will commutate with the evaluation board(s) and tuner(s) to identify which are in use. The applicable part numbers will be displayed under “device info” during initialization and on the front panel while the radio is in operation. Only the available application modes and tuners will be displayed by the GUI when initializing the tuner. Note that this user’s guide may show figures with application modes and features that may not be available depending upon the tuner part number or daughter card in use. Figure 7. Initialization Window 1. Start the software by either using the desktop shortcut or from: Start Programs Silicon Laboratories, Inc Silicon Labs Audio GUI 2. Configure initialization options as shown in Figure 7. “Initialization Window”. A number of powerup options are available: a. EVB Application: Select one of the following EVB application modes: Single tuner RDS/VICS b. Initial Boot Mode: Selects whether the receiver will first start in FM Receive mode, AM Receive mode, etc. c. Clock Configuration: This section displays information on the crystal oscillator clock frequency and crystal loading cap capacitance. The Clock frequency can not be modified in conjunction with a Quark Baseboard. d. Output Mode: Configures tuner and EVB for either analog or MPX output through the HEADPHONE_OUT and L/R LINE_OUT jacks. Use the HEADPHONE_OUT jack for listening through headphones or powered speakers. Use the L/R LINE_OUT jack for low-distortion measurements. Other output modes are not supported by the Quark Baseboard. e. XTAL Loading Cap: Indicates the crystal frequency trim capacitance. This is retrieved from an EEPROM on the daughtercard. Additional options are available in the Firmware Configuration window, shown in Figure 9. “Firmware Configuration Window”. 8 Rev. 0.3 Si477x-EVB f. Firmware selection: The firmware for the tuner (or tuners in multi-tuner configurations) may be selected by selecting the appropriate Tuner tab as shown in Figure 9. “Firmware Configuration Window”. In particular, i. Select either the firmware image in the chip's NVRAM by selecting From Device or ii. Select a firmware image from a list of options. g. Part Number and I2C address for the selected device. These are read back/configured automatically from the tuner or ID EEPROM on the daughtercard. h. Default Mode: UI default mode allows the selection of the UI configuration as a default for the part number, last used UI state, or you can select a configuration previously saved (see Figure 8). For saving a UI configuration, see Section 5.1. Figure 8. Default Mode Selection Rev. 0.3 9 Si477x-EVB Note: If window displays "No Boards Found", check USB connections and power supply configuration. Figure 9. Firmware Configuration Window 10 Rev. 0.3 Si477x-EVB 5. Saving, Retrieving, and Deleting the Configuration State This GUI feature allows the user to save, retrieve and delete the configuration state which contains the property values. 5.1. Saving the Current Configuration State This feature allows the user to save the current configuration state which contains the property values. 1. Go to File State Management Save Current State as shown in Figure 10. Figure 10. Saving Configuration State 2. Click on Save Current State and the Select Configuration window shown in Figure 11 will pop up. Enter the name of the configuration state and click OK. The current state called My Configuration which contains the property values is now saved. Figure 11. Naming a Configuration State During Save Rev. 0.3 11 Si477x-EVB 5.2. Retrieving the Configuration State This feature allows the user to retrieve the configuration state. 1. Go to File Initialize Tuner 1 tab as shown in Figure 12. The different states which were saved before are available in the default mode for user selection. Figure 12. Saved Configuration State 2. In Figure 13 below configuration state My Configuration is selected. Once the selection is made, click on Initialize and the part will boot with the property values stored in the My Configuration state. Figure 13. Power Up from Saved Configuration State 12 Rev. 0.3 Si477x-EVB 5.3. Deleting the Configuration State This feature allows the user to delete the configuration state. 1. Go to File State Management Delete State as shown in Figure 14. Figure 14. Delete Configuration State 2. Click on Delete state and the Delete Configuration window shown in Figure 15 will pop up. Select the configuration state you want to delete and click OK. Figure 15. Selecting Configuration State to Delete In addition to saving, retrieving and deleting the configuration state the GUI also gives the end user the ability to export the contents of the configuration state into a file, the contents of which can be viewed using a text editor and which can be imported to different machines to allow multiple users to test the tuner with the same configuration state. Rev. 0.3 13 Si477x-EVB 5.4. Exporting Saved State This feature allows the user to export the contents of the configuration state into a file. 1. Go to File State Management Export Saved State to export the saved state into a file as shown in Figure 16. Figure 16. Exporting Saved State 2. Click on Export Saved State and the Select Configuration to Export window will pop up as shown in Figure 17. Figure 17. Selecting Configuration State to Export 3. Select the configuration state to export and click OK to save the configuration file with a .ini extension. This configuration file can now be opened in a text editor and saved to different machines. The contents of the configuration file will be displayed in a format as shown in Figure 18 below. 14 Rev. 0.3 Si477x-EVB Figure 18. Saved Configuration File Rev. 0.3 15 Si477x-EVB 5.5. Import State File This feature allows the user to import the configuration state file which has been saved using Export Current State and hence use the same configuration state file on different machines. 1. Go to File State Management Import State File to export the saved state into a file as shown in Figure 19. Figure 19. Import Configuration State 2. Select the file to import. 3. Once the state file is imported it will show up in the Default Mode of the Initialization window. In Figure 20 below the test.ini file was imported using Import State File and once that was done it shows up in the default mode in the Initialization window. Figure 20. Selecting Imported State File 16 Rev. 0.3 Si477x-EVB 5.6. AM Receive Mode Initialize the receiver as described in Section “4.2. Initialization”, selecting AM mode. The Tuner panel will appear as shown in Figure 21. “AM Tuner Window”. Figure 21. AM Tuner Window 1/2.Frequency Numerical Window/Slider: Use to set the receiver frequency. This also acts as an indicator for receive frequencies selected by seek or preset features. Note that frequency resolution is set by the Band and Spacing properties of the tuner via the Properties window. 3.Tuning Increment/Decrement: Adjusts receiver frequency in increments set by the Spacing property. 4. Seek: Executes tuner Seek command as configured by the applicable Seek/Tune properties. 5. Auto Scan: Executes sequential tuner Seek commands to cover the entire band. Valid stations are denoted beneath the tuner by red tick marks. Clicking the To Presets button automatically populates the presets with the strongest twelve stations found. 6. Presets: Each Preset button stores frequencies for convenient recall. Frequencies may be either automatically programmed using the Auto Scan as described above or may be manually set by selecting a frequency and holding the desired button until the frequency is memorized. 7. Volume/Mute: Sets the audio L/R output volume. The Mute button engages the AUDIO_MUTE property for both channels. Note: Volume must be set to maximum (63) for all performance tests. Rev. 0.3 17 Si477x-EVB 8. Status Indicators: These indicators show the various metrics reported back to the user via either the AM_RSQ_STATUS or AM_ACF_STATUS API commands. Commonly used metrics include the following: RSSI: The Received Signal Strength Indicator at the IC input. Note that this will vary from the actual antenna RSSI due to front end gains or losses. SNR: The Signal to Noise Ratio at the demodulator input. Note that this is not the SNR of the Audio output. LASSI: Adjacent Signal Strength Indicator. Indicates (signal + noise) at the low-side adjacent frequency in dB relative to the wanted carrier. HASSI: Adjacent Signal Strength Indicator. Indicates (signal + noise) at the high-side adjacent frequency in dB relative to the wanted carrier. Freq Off: Frequency offset of received signal. Chan BW: Receiver channel bandwidth. Hicut: Hicut corner frequency. Soft Mute: Indicates the attenuation applied. 9. Status Indicator Undock: Opens a separate window with status indicators, as shown in Figure 22. “AM Status Indicator Window”. Figure 22. AM Status Indicator Window 10. Band Selector: Chooses which AM/SW/LW band to use for frequency tuning/seeking Notes: Many of these mitigation engines and indicators are configured via properties. to the Programming Guide for specific detail, including configuration, applicable ranges, etc. The USB power supply is provided for convenience only. Better performance will be attained using the external 9 V supply option. Refer 18 Rev. 0.3 Si477x-EVB 5.7. FM Receive Mode Initialize the receiver as described in Section “4.2. Initialization”, selecting FM mode. The Tuner panel will appear as shown in Figure 23. “FM Tuner Window”. Figure 23. FM Tuner Window 1/2.Frequency Numerical Window/Slider: Use to set the receiver frequency. This also acts as an indicator for receive frequencies selected by seek or preset features. Note that frequency resolution is set by the Band and Spacing properties of the tuner via the Properties window. 3.Tuning Increment/Decrement: Adjusts receiver frequency in increments set by the Spacing property. 4. Seek: Executes tuner Seek command as configured by the applicable Seek/Tune properties. 5. Auto Scan: Executes sequential tuner Seek commands to cover the entire band. Valid stations are denoted beneath the tuner by red tick marks. Clicking the To Presets button automatically populates the presets with the strongest twelve stations found. 6. Presets: Each Preset button stores frequencies for convenient recall. Frequencies may be either automatically programmed using the Auto Scan as described above or may be manually set by selecting a frequency and holding the desired button until the frequency is memorized. 7. Volume/Mute: Sets the audio L/R output volume. The Mute button engages the AUDIO_MUTE property for both channels. Note: Volume must be set to maximum (63) for all performance tests. 8. Status Indicators: These indicators show the various metrics reported back to the user via either the FM_RSQ_STATUS, FM_AGC_STATUS or FM_ACF_STATUS API commands. Commonly used metrics include: RSSI: The Received Signal Strength Indicator at the IC input. Note that this will vary from the actual antenna RSSI due to front end gains or losses. SNR: The Signal to Noise Ratio at the demodulator input. Note that this is not the SNR of the Audio output. LASSI: Low Side Adjacent (100 kHz) Channel Strength Indicator reports the (Signal + Noise) power relative to the carrier. HASSI: High Side Adjacent (100 kHz) Channel Strength Indicator reports the (Signal + Noise) power relative to the carrier. ASSI200: The 200 kHz offset alternate signal strength indicator. Indicates (signal + noise) at the 200 kHz offset alternate channel in dB relative to the wanted carrier. Returns the maximum of high and low side alternate channels. Rev. 0.3 19 Si477x-EVB USN: The Ultrasonic Noise indicator. Higher numbers indicate better signal quality. Multipath: Multipath indicator. Higher numbers indicate more severe multipath impairment. Freq Off: Frequency offset of received signal. Deviation: FM deviation indicator Channel BW: Receiver channel (IF) bandwidth. Stereo: Indicates the Stereo/Mono blend ratio. HI-Cut/HI-Blend: Hicut mitigation applied to either the Left Plus Right (LPR) or Left Minus Right (LMR) audio signals. Soft Mute: Indicates the soft mute attenuation applied. FMAGC1, FMAGC2, PGA Gain: AGC indicators for FM AGC. 9. Status Indicator Undock. Opens a separate window with all status indicators for more convenient viewing as shown in Figure 24. “FM Status Indicator Window”. Figure 24. FM Status Indicator Window 10. Stereo/Mono selector. Force the receiver to mono mode by selecting this button. The tuner will automatically blend between stereo and mono mode when Stereo is selected. 11. RDS Program Service and Radio Text indicators. Displays received RDS strings. Notes: Many of these mitigation engines and indicators are configured via properties. Refer to the Programming Guide for specific details, including configuration, applicable ranges, etc. The USB power supply is provided for convenience only. Better performance will be attained using the external 9 V supply option. 20 Rev. 0.3 Si477x-EVB 5.8. Configuring Tuner Properties As described in the Programming Guide, various tuner aspects are configured through either a command/response or get/set property API interface. The GUI contains a window to help manage properties under Window Properties as shown in Figure 25. “Properties Window”. Figure 25. Properties Window Properties are grouped by category. Properties specific to the Si477x device are prefixed with either FM or AM. FM RDS Settings, FM UI Settings, and AM UI Settings are categories that are used to control UI behavior but do not modify the property settings on the Si477x device. To see all properties associated with the Si477x device, choose FM: All or AM: All: All, depending on what mode the device is powered up into. Most properties included in the API are also included in the properties window. Clicking on a particular property opens a brief description of the property and its arguments. Refer to the Programming Guide for detailed information on the properties and values. Property addresses and values can be displayed or hidden using the Display/Hide Details button. When displayed, all of the current properties can be viewed or exported to a file (using the Export Properties button) and the last property changed is displayed. By clicking the Export Properties button shown in Figure 25, the properties can be exported to a .csv file. Rev. 0.3 21 Si477x-EVB 5.9. Register Read/Write The software's graphical user interface and property windows provide an easy, intuitive method of configuring the device. In development, however, it is often useful to have low-level bytewise read/write interface to the tuner. The GUI provides this interface under Window Register Map. Figure 26. “Register Map Window” shows an example read/write operation. The FM_RSQ_STATUS request is sent with an ARGument of 0x00. The reply returned in the RESPonse fields. Refer to the Programming Guide for detailed information on the register definitions and their arguments and responses. Figure 26. Register Map Window 22 Rev. 0.3 Si477x-EVB 5.10. Other Useful Tools 5.10.1. RSSI/SNR Graphing Utility The Graphing utility Window RSSI/SNR Graph provides a scan of user selectable metrics versus frequency. Graphing options include RSSI, SNR, Low Adjacent Channel Strength (LASSI), and High Adjacent Channel Strength (HASSI). These metrics can be individually selected for display. A line or bar graph style can be chosen and markers indicating valid stations and their frequencies can be displayed. Once the preferred graphing and displays have been selected, click the “Draw” button. Figure 27 shows an example scan in the FM band. Stations above the red line meet the RSSI threshold for valid stations. The SNR page shows a complementary scan of SNR values across the band as well as the SNR threshold for valid stations. Figure 27. RSSI/SNR Graphing Utility Rev. 0.3 23 Si477x-EVB 5.10.2. Blend/Hicut/Soft Mute Configuration Helper The mitigation engines such as FM stereo/mono blend, hi-cut, hi-blend, and soft mute have configurable low- and high-end thresholds. These thresholds may be configured numerically through the Properties page or graphically through the Configuration Helper. Figure 28 shows an example of the Configuration Helper set to display FM stereo/mono blend based on RSSI. This example also provides the ability to set the Fast and Slow metrics on the same screen. If a configuration setting does not have Fast and Slow metrics available, only one graph and column of configurable values will appear. On both graphs the green line depicts the blend (in percent stereo). The green point shows the current operating point of the receiver (30 dBuV RSSI which results in 18% stereo given the property settings). The cyan line reflects the actual reported stereo value (14%) from the Si477x device which is mitigated by all the metrics (RSSI/Multipath/ USN) in this example. Since the cyan line is tracking the green point or RSSI mitigated blend, the device is limiting stereo based on RSSI in this example. When selecting a mitigation control item, the description text is updated automatically. The name of the property being changed is displayed in bold. The property can then be found in the property window by finding the property with the same name being displayed in the configuration helper. Changes made to this page are applied to the tuner immediately, making it a useful tool in real-time configuration of the mitigation engines. Figure 28. Configuration Helper 24 Rev. 0.3 Si477x-EVB 5.10.3. RDS Receive Data The Si477x UI features tools help in capturing and analyzing RDS performance. The first is the RDS Receive Data window (under menu Window RDS Receive Data). This shows various RDS metrics such as the decoded RDS fields, group counters, and performance statistics. This is shown in Figure 29. Figure 29. RDS Receive Data Window The second is a graphical display of the RDS group counter information, shown in Figure 30. This window is available under menu Window RDS Group Counters. Figure 30. RDS Group Counter Window Rev. 0.3 25 Si477x-EVB 6. Hardware Description The evaluation hardware consists of two components: a daughtercard and a baseboard. Note: Refer to Rev. 0.1 of this document if the Si475x/6x Baseboard is supplied. 6.1. Feature Overview Figure 31. “EVB Features Using Quark Baseboard” shows various connections, jumpers, adjustments, and features for an EVB using a Quark baseboard. 17 18 1 4 2 6 20 19 22 9 7 16 11 3 10 12 15 13 8 14 5 21 Figure 31. EVB Features Using Quark Baseboard 26 Rev. 0.3 Si477x-EVB Table 1. EVB Feature Descriptions Reference Description 1 J1 2 JP1 AM antenna connector 3 J33 AM test connector 4 FM antenna connector/test conductor. Tuner pin/net connection points. 5 J48 Tuner pin/net connection points. 6 J56 9 V input to LDOs. Maximum 11 V. 7 J1 VIO 1/2 inputs. Source with bench power supply if on-board LDOs are not used. 8 J2 VA/VD inputs. Source with bench power supply if on-board LDOs are not used. 9 R72 VIO1 LDO adjust. (1.2–3.6 V, nominal 3.3 V) 10 J57 Selects tuner VIO1 source from LDO or TERMinal. 11 R74 VIO2 LDO adjust. (1.7–3.6 V, nominal 3.3 V) 12 J60 Selects tuner VIO2 source from LDO or TERMinal. 13 J59 Selects tuner VA source from fixed 5 V LDO/USB or TERMinal. 14 J58 Selects tuner VD source from LDO or TERMinal. 15 R73 VD LDO adjust. (2.7–3.6 V, nominal 3.3 V) 16 SW1 Selects USB or 9 V input to LDO. Note that in USB position PC 5 V sources VA directly which could result in decreased performance. Center position is off. 17 J13 L/R_LINE_OUT. L/R lineout (direct from tuner). (Rev 3 and later) Buffered/110 kHz lowpass filtered L-ch analog output when in MPX mode. (Rev 2) 18 J14 HEADPHONE_OUT. Buffered headphone out. (Rev 3 and later) Buffered, 30 kHz lowpass filtered L, R channel outputs when in L/R audio mode. (Rev 2) 19 D3-D6 20 PB1 MCU Reset. 21 J15 USB connector. 22 J9-J12 LEDs. Current measurement jumpers. Rev. 0.3 27 Si477x-EVB 6.2. Daughtercard Each evaluation kit will be provided with an Si477x daughtercard. Each daughtercard contains the minimal application circuit, including the following: Si477x Tuner IC RF Input circuitry Crystal EEPROM for serial number, calibration constants, and crystal information Each daughtercard features a number of test points with direct access to the tuner signal pins. These signals may be disconnected from the baseboard connector by removing either a 0 jumper or by removing a solder dot on a printed chevron pattern. Small vias allow for connection via wire-wrap wire. The reference frequency is generated by the on-chip crystal oscillator by default. If desired, the reference clock may be sourced by the baseboard oscillator or an external generator by removing the crystal and inserting a 0.1uF capacitor to bridge the connection. Refer to "7. Hardware Schematics and PCB Layout" on page 32 for daughtercard schematics and PCB layouts. 6.3. Baseboard The Quark baseboard contains all support circuitry, including the following: Power supplies: all four Si477x supplies derived from USB 5 V or wall pack 9 V supplies USB HID-based communications interface via C8051F340 microcontroller Test points for all tuner interface I/O lines Direct and buffered L/R/MPX analog outputs 6.3.1. Power Supplies On-board LDOs generate VA, VD, VIO1, and VIO2 supplies for the tuner. Three of these, VD, VIO1, and VIO2, are adjustable via trimpot. Level translation to other blocks, such as the microcontroller, is via discrete translators. Switch SW1 selects the LDO configuration as sourced from the 9 V coaxial connector or the USB 5 V supply from the PC. When in the USB position, the 5 V analog supply to the tuner is derived directly from the PC USB supply. Notes: The USB power supply option is provided for convenience but may result in decreased RF performance due to PC power supply noise and lack of regulation between PC and the tuner's analog power supply. Regulation inaccuracy and cable loss may result in a VA supply voltage below specification. Ensure any wall power supply has a maximum output voltage of less than 11 V. Higher voltages will engage a clamping diode and may damage the LDOs. Jumpers, shown highlighted in Figure 32. “Power Supply Jumpers”, select each tuner supply's source as either the on-board LDO (shown) or external (via J1/J2). Tuner supply currents may be measured by opening jumpers J9-J12 and inserting an ammeter in positions JP8JP11. 28 Rev. 0.3 Si477x-EVB Figure 32. Power Supply Jumpers 6.3.2. Microcontroller/USB Interface Communication to the tuner and configuration is through firmware on a Silicon Laboratories C8051F340 USB microcontroller. This device translates USB commands via HID interface to I2C control words to the tuner. PB1 resets the microcontroller. LED's D3–D6 are driven by the microcontroller. The green LED D4 lights when the microcontroller has booted. The USB connection may be disconnected once the tuner is configured. Tuner settings will persist until reset or the power is removed. Rev. 0.3 29 Si477x-EVB 6.3.3. Headphone Amplifier/Buffer Left and Right audio outputs are buffered and lowpass filtered by on-board amplifiers in Figure 33. “Audio Output”. The software automatically selects the L/R audio-band output when AM or FM modes are selected. The left channel/MPX output is selected in MPX mode only. Unbuffered L/R outputs are available at the debug header J48. Note: Use L/R outputs directly from tuner for THD, SINAD, and stereo imbalance measurements. The headphone amplifier may degrade performance. The analog L/R and MPX outputs are available at two 3.5 mm jacks. The function of each jack varies by baseboard revision. The left jack is a direct, dc-coupled L/R/MPX output from the tuner. This output should be used for all low-distortion laboratory measurements. The right jack is an ac-coupled, unity-gain-buffered L/R output for listening through headphones or powered speakers. Figure 33. Audio Output 30 Rev. 0.3 Si477x-EVB 6.4. Si4770Module-A-EVB Separately from the Si477x-EVB kit, user's may also order an Si4770Module-A-EVB kit. The Si4770Module-A-EVB kit consists of an Si4770 Module and Si477x Interposer card. Together, these serve in place of a daughter card on an Si477x EVB. Alternatively, the Si4770 Module can be installed into a user-created system with a compatible pinout. To use the Si4770Module-A-EVB in conjunction with an Si477x EVB, connect the module, interposer card, and baseboard as shown in the figure below. Note: The Si4770 Module is configured by default for an AM Loop Antenna connected through the Si47xx Interposer card. For optimum results in conducted tests through the AM Test SMA connector, remove transformer T2 from the AM signal path on the Si4770 Module. Figure 34. Si4770Module-A-EVB Module and Interposer Card Rev. 0.3 31 Si477x-EVB 7. Hardware Schematics and PCB Layout This section contains schematics, PCB layouts, and Bills of Material for all daughtercards (DCs) and the baseboard (BB). 32 Rev. 0.3 $ % Rev. 0.3 ' 60$B('*( - $0$17 60$B('*( -3 $,5/223$17 5) 5) & 3) - )0$17 5) 13 7 6,/$%6 6/7) - 13 - (6'B',2'( 5 5 5) 5) 5) 13 & 5) & 13 5) / 13 5) / 13 & 5 5 5 13 2SWLRQDO)0,QWUXVLRQ)LOWHU / 13 & 5 (6'B',2'( 13 - & 5 ' *1' 5) & 13 & 13 & 13 5) & 3) - 5) 1) & & 8) & & 13 5 13 5) 5) 5 5 5) & / 1) 1+ 7 5) )09$5 )0;,3 )0;,1 *1'5) 5)5(* )02 )0, :;, - $0, & 13 8 6,; - 9' ;287 '&/. ')6 '287 4287 ,287 ,4)6 ,4&/. 9,2 '%<3 & 1) & 3) & 8) & 1) 9$ & 1) & 1) & 8) 6&$/( 9B9B%% *3,2B *3,2B - - - - - - - - - - - - 6+((7 ,'B((3520B6'$ ,'B((3520B6&. $ 9&& 9B9B%% RI $ 6'$ /& *1' 6&/ 8 & 8) ,&21B715 'BB715 'BB715 'BB715 'BB715 567%BB715 9B3*0B715 9,2B715 ,17%BB715 6&/B715 6'$B715 567%BB715 9'B715 9,2B715 '&/.B715 ')6B715 '287B715 4287B715 ,287B715 ,4)6B715 ,4&/.B715 ;287B715 ;,1B715 5287B715 /287B715 ,&,1B715 ,&,3B715 9$B715 ((3520IRUDXWRPDWLF,'61RI(9% *3,2B *3,2B 'B 9B3*0 9B3*0 'B 9,2 ,17%B 6&/ 6'$ 567%B 9,2 ,17%B 6&/ 6'$ 567%B - - 9,2 9,2 9' - - - - - - - '&/. ')6 '287 4287 ,287 ,4)6 ,4&/. - - - - - - - '&/. ')6 '287 4287 ,287 ,4)6 ,4&/. ;287 ;287 5287 /287 ;,1 5287 /287 ;,1 *3,2B *3,2B 9$ *3,2B *3,2B Figure 35. Si477x Rev 2.0 Schematic ('%(// '5$:1%< 6LOLFRQ/DERUDWRULHV&RQILGHQWLDO'LVFORVXUHXQGHU1'$RQO\ 5) 5) (6'B',2'( ' / 1+ 5) 5) / 1+ & 13 & 8) 0+= ; $ $ *1'B3$' [ )0$*& )0$*& *3,2 *3,2 '$&5() ;7$/ ;7$/ 5287 /287 9$ 1& 1& 567% 6'$ 6&/ ,17% 9,2 9' & 13 / 1+ ,17%BB715 'BB715 ,'B((3520B6'$ ,'B((3520B6&. ,&21B715 'BB715 % 6,=( 7,7/( B ':*12 Si477x LNA_BALUN :HVW&HVDU&KDYH] $XVWLQ7H[DV86$ 6LOLFRQ/DERUDWRULHV,QF 9B3*0B715 6'$B715 ,17%BB715 9'B715 'B715 ,4)6B715 ')6B715 4287B715 /287B715 ,&,3B715 9$B715 - &211B6)0B60 5(9 $ % Si477x-EVB 7.1. Si477x Daughtercard Rev 2.0 33 Si477x-EVB Table 2. Si477x DC Rev 3.0 Bill of Materials Qty Ref Des Description Value Mfr Mfr Part Number 1 C1 CAP,SM,0402 100PF MURATA GRM1555C1H101JZ01 1 C10 CAP,SM,0402 18PF MURATA GRM1555C1H180JZ01 8 C11,C12,C22, C23,C24,C25, C26,C27 CAP,SM,0402 NP 3 C13,C17,C21 CAP,SM,0402 0.1UF MURATA GRM155R71A104KA01D 5 C2,C3,C4,C5, C7 CAP,SM,0402 2.2NF MURATA GRM155R71H222KA01 2 C6,C20 CAP,SM,6.3V, X5R,0603 10UF MURATA GRM188R60J106ME47D 1 C8 CAP,SM,0402 1NF MURATA GRM155R61H102KA01 1 C9 CAP,SM,0402 62PF MURATA GRM1555C1H620JD01 3 D1,D2,D3 ESD PROTECTOR,SM DIGIKEY PESD0402-140TR-ND 2 J1,J33 CONN, SMA, EDGEMOUNT YAZAKI RA2EJ2-6G 1 J2 CONN,SM,2X30 SAMTEC SFM-130-02-S-D-A 1 JP1 CONN,TH,HEADER,1X2 SAMTEC HTSW-101-07-G-D 1 L1 IND,SM,0603 220NH MURATA LQW18ANR22G00 1 L2 IND,SM,0603 47NH MURATA LQW18AN47NG00 1 L3 IND,SM,0603 150NH MURATA LQW18ANR15G00 1 L9 IND,SM,0603 10NH MURATA LQW18AN10NJ00D 2 R1,R4 RES,SM,0402 0R 1 R5 RES,SM,0402 NP 1 T1 BALUN,1:1, TOKO TOKO 458PT1566 1 T2 TRANSFORMER,THRU-HOLE SILABS SL755TF01 1 U1 IC,SM,SI4770,MLP40 SILICON LABORATORIES SI477x 1 U2 IC,SM,RAM MICROCHIP 34LC02 1 X1 XTAL,SM,3.2 X 2.5 MM TAI_SAW TZ1522A 34 37.209375 MHz Rev. 0.3 Si477x-EVB Figure 36. Si477x Daughtercard Rev 2.0 Silkscreen Rev. 0.3 35 Si477x-EVB Figure 37. SI477x Daughtercard Rev 2.0 L1 Copper 36 Rev. 0.3 Si477x-EVB Figure 38. Si477x Daughtercard Rev 2.0 L2 Copper Rev. 0.3 37 Si477x-EVB Figure 39. Si477x Daughtercard Rev 2.0 L3 Copper 38 Rev. 0.3 Si477x-EVB Figure 40. Si477x Daughtercard Rev 2.0 L4 Copper Rev. 0.3 39 JP1 JP2 JP5 JP3 Rev. 0.3 4 JP4 29 34 32 30 IQCLK_TNR VIO2_TNR V_3V3_BB 1 3 DRAWN BY SERGIO C. 40 42 44 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 DCLK_TNR DFS_TNR DOUT_TNR QOUT_TNR IOUT_TNR IQFS_TNR IQCLK_TNR D_TNR VIO2_TNR VD_TNR V_PGM D_0_TNR D_1_TNR D_2_TNR D_3_TNR 52 54 56 58 60 51 53 55 57 59 ICON_TNR ICIP_TNR 2 50 49 SDA_TNR ICOP_TNR SHEET 48 47 SCL_TNR SCALE 46 45 38 36 34 32 30 28 26 24 22 20 18 16 14 12 9 11 LOUT_TNR 10 8 6 5 7 4 3 ROUT_TNR 2 1 J48 CONN2X30 GND 1 of ICIN_TNR 5 RSTB_1_TNR RSTB_2_TNR VIO1_TNR INTB_1_TNR INTB_2_TNR Tuner Test Points VA_TNR Daughter Card Interfaces 2 Figure 41. Quark Baseboard Schematic: Connectors ID_EEPROM_SCK ID_EEPROM_SDA 3 5 2 6 ICON_TNR D_3_TNR D_1_TNR V_PGM INTB_2_TNR SDA_TNR INTB_1_TNR VD_TNR D_TNR IQFS_TNR QOUT_TNR DFS_TNR LOUT_TNR ICIP_TNR VA_TNR 4 7 8 H1 9V_HOLDER 9 10 ICOP_TNR 11 12 D_2_TNR 13 14 15 16 D_0_TNR 17 19 21 18 20 RSTB_1_TNR RSTB_2_TNR 22 SCL_TNR 23 25 26 24 27 33 35 28 VIO1_TNR VD_TNR 31 36 IOUT_TNR 37 38 DOUT_TNR 39 41 40 42 DCLK_TNR 43 45 44 47 46 48 XOUT_TNR 49 51 50 52 53 55 56 54 57 58 59 XIN_TNR ROUT_TNR ICIN_TNR VA_TNR 60 J51 CONN_TFM_TH Tuner Daugher Card (_TNR) 3 J17 J18 40 A B 4 B SIZE TITLE 1 11-10-2011_16:10 DWG NO QUARK BASEBOARD Connectors 400 West Cesar Chavez Austin, Texas 78701 USA +1 512 416 8500 Silicon Laboratories, Inc. Can be used to populate a 2x7 HDR for use with ISCB board. U1_EN/DISABLE VIO1_REF U3_EN/DISABLE VIO1_REF 1 1.0 A B Si477x-EVB 7.2. Quark Baseboard Rev 1.0 A B 0R L1 0R L2 4 C34 100PF F5 +11.5V Maximum!! C29 100PF F4 C30 100PF C33 100PF C31 0.1UF External / USB power selection For use with 9V Battery JP7 2 1 1 V_9V_EXT 3 2 J56 CONN_PJ-016 V_5V_USB C32 0.1UF 1 4 5 6 7 8 EG4319 Rev. 0.3 C15 10UF C6 10UF IN GND GND OFF MAX604 U20 3 1 2 3 4 U5 MAX604 OUT GND GND SET 8 7 6 5 8 7 6 5 IN GND GND OFF U19 MAX604 OUT GND GND SET 8 7 6 5 IN GND GND OFF U18 MAX604 OUT GND GND SET 8 7 6 5 IN GND GND OFF U17 MAX604 DRAWN BY R2 0R R3 NP 8 7 6 5 R18 10K CW CW C19 0.1UF WIPER CCW WIPER CCW CW CCW WIPER R17 3.16K SERGIO C. C18 100PF OUT GND GND SET Vo = 1.2 (1 + Rtop/Rbot) 1 2 3 4 VIO2: Adjustable 1.7 - 3.6V Vo = 1.2 (1 + Rtop/Rbot) 1 2 3 4 VIO1: Adjustable 1.2 - 3.6V Vo = 1.2 (1 + Rtop/Rbot) 1 2 3 4 VD: Adjustable 2.7 - 3.6V Resistors optional: can use to set other than default 3.3. IN GND GND OFF OUT GND GND SET Vo = 1.2 (1 + Rtop/Rbot) 1 2 3 4 BaseBoard: Fixed 3.3V V_UNREG C7 10UF C9 10UF C11 10UF VA: 5V (normal) C14 10UF R11 4.99K R74 10K R12 0R R14 8.87K R72 10K R13 7.87K R16 29.4K R73 10K R15 48.7K C27 100PF Si475x Power Supplies C21 0.1UF C24 0.1UF C26 0.1UF 2 C5 10UF C8 10UF C10 10UF C12 10UF 1 SCALE R1 NP 2 J16 SHEET 2 V_3V3_BB 3 of 1 5 TO MCU 4 J2 PWR_TERM Used to disconnect 3V3 from MCU JP6 C22 100PF C23 100PF C25 100PF C28 0.1UF 2 Figure 42. Quark Baseboard Schematic: Power Supplies ZENER_11V D2 2 3 SW1 9 10 11 12 13 14 15 16 3 10K R20 4 3 4 J59 1 B SIZE VIO2_TNR DWG NO 1 QUARK BASEBOARD Si475x Power Supplies JP11 1.0 C173 10UF C170 10UF VIO2_REF Tuner current measmt point J12 JP10 VIO1_TNR VIO1_REF Tuner current measmt point J11 JP9 Tuner current measmt point 400 West Cesar Chavez Austin, Texas 78701 USA +1 512 416 8500 TITLE VD_REF C172 10UF C171 10UF VA_TNR VA_REF J10 VD_TNR JP8 J9 Tuner current measmt point Silicon Laboratories, Inc. LDO / term selection J60 LDO / term selection J57 LDO / term selection J58 LDO / term selection 11-10-2011_16:07 2 J1 PWR_TERM A B Si477x-EVB 41 42 A B ROUT_TNR LOUT_TNR 4 4 Rev. 0.3 0R R31 0R R30 0.33UF C52 0.33UF C53 SERGIO C. DRAWN BY 20K R4 SCALE 20K R19 LM4911 2 BYPASS VOB INB GND VOC VOA VDD 20K U2 MUTE SD INA C3 10UF 5 4 3 R26 2 1 20K R24 20K V_3V3_BB AUDIO_HP_SHDN R25 Analog Audio Path 2 6 7 8 9 10 SHEET C43 0.1UF 3 V_3V3_BB of 5 C37 NP C36 NP place close to amp C4 100PF C35 100PF C20 100PF place close to amp Figure 43. Quark Baseboard Schematic: Analog Audio Path 3 3 J4 NP C1 NP J3 C2 B 1 11-10-2011_15:00 DWG NO QUARK BASEBOARD Analog Audio Path 400 West Cesar Chavez Austin, Texas 78701 USA +1 512 416 8500 TITLE SIZE Headphone out Line out connections J14 2 3T R 1S Silicon Laboratories, Inc. J13 2 3T R 1S F7 place close to jack F3 place close to jack F6 place close to jack 1 1.0 A B Si477x-EVB Rev. 0.3 A B 1 V_3V3_BB 2 GND L3 GND DD+ VCC J15 R46 1K 1 4 1K R45 F1 D+ D- 4 C57 NP 1 PB1 Button C2 debug/ reset J46 TSM-105-01-T-DV 1 2 3 4 5 6 7 8 9 10 SP0503BAHT 2 3 D1 Connector shell not grounded. 1UF 3 4 USB_CHOKE C164 USB_CONNECT C168 10UF 2 RSTB_C2CK_MCU_A C169 10UF C93 0.1UF 1 2 3 4 5 6 7 8 9 10 11 12 P0.5 P0.4 P0.3 P0.2 P0.1 P0.0 GND D+ DVDD REGIN VBUS R69 0R R66 0R U8 C08051F340 R78 160 3 R77 160 R79 160 R80 2.15K P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 P3.0 P3.1 P3.2 P3.3 P3.4 P3.5 36 35 34 33 32 31 30 29 28 27 26 25 DRAWN BY Yl D3 SERGIO C. Bl D5 R63 0R R64 0R Gr D4 Rd D6 SCALE V_3V3_BB 2 R47 10K R48 6.49K ID_EEPROM_SDA ID_EEPROM_SCK 2 SHEET R51 10K R52 6.49K Figure 44. Quark Baseboard Schematic: MCU TO LDO's C56 0.1UF F2 V_5V_USB C2D_MCUA C58 0.1UF V_3V3_BB R70 0R R68 0R Baseboard Control MCU 3 48 47 46 45 44 43 42 41 40 39 38 37 P0.6 P0.7 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 P2.0 P2.1 /RST/C2CK C2D P4.7 P4.6 P4.5 P4.4 P4.3 P4.2 P4.1 P4.0 P3.7 P3.6 13 14 15 16 17 18 19 20 21 22 23 24 4 4 of R53 10K 5 R54 19.1K R5 4.7K R49 10K U7 A05 VCC6 (SDA_TNR) B SIZE TITLE DWG NO 1 QUARK BASEBOARD MCU 400 West Cesar Chavez Austin, Texas 78701 USA +1 512 416 8500 Silicon Laboratories, Inc. C98 0.1UF (ICIP_TNR) (ICIN_TNR) (D_3_TNR) (D_2_TNR) (D_1_TNR) (ICON_TNR) (ICOP_TNR) (D_O_TNR) (V_PGM) (RSTB_2_TNR) (RSTB_1_TNR) (INTB_2_TNR) (SCL_TNR) (INTB_1_TNR) 20-10-2011_09:39 VIO2_REF VA_REF VD_REF VIO1_REF A1 4 SDA 34LC02 GND SCL R50 6.49K 3 2 1 R6 4.7K V_3V3_BB AUDIO_HP_SHDN D14_MCU D13_MCU D12_MCU D11_MCU D10_MCU D9_MCU D8_MCU D7_MCU D6_MCU D5_MCU D4_MCU D3_MCU D2_MCU D1_MCU D0_MCU 1 1.0 A B Si477x-EVB 43 44 A B Rev. 0.3 4 ICIP_TNR ICIN_TNR D_3_TNR D_2_TNR D_1_TNR ICOP_TNR ICON_TNR D_0_TNR V_PGM RSTB_2_TNR RSTB_1_TNR INTB_2_TNR INTB_1_TNR R37 4.7K C49 0.1UF R39 4.7K VIO1_REF 1 2 3 4 5 VL1 VL VL2 VL3 VL4 20 VCC1 19 VCC 18 VCC2 17 VCC3 16 VCC4 15 VCC5 14 VCC6 13 VCC7 12 VCC8 11 GND EN 5 SDAB 6 U3 U9 4 GND 3 SDAA V_3V3_BB V_3V3_BB C50 10UF C44 1UF C45 4.7NF 0R 0R 0R R83 0R R65 0R R23 0R R22 R21 0R 0R R59 0R R60 0R R61 0R R67 0R R71 0R R75 0R R76 R62 3 C17 10UF VL1 VL VL2 VL3 VL4 20 VCC1 19 VCC 18 VCC2 17 VCC3 16 VCC4 15 VCC5 14 VCC6 13 VCC7 12 VCC8 11 GND C48 0.1UF DRAWN BY SERGIO C. C16 0.1UF C42 10UF SCALE 2 SHEET (OPTIONAL DEFAULT NO-POP) V_3V3_BB U1_EN/DISABLE MAX3002 U1 U3_EN/DISABLE MAX3002 VL5 VL6 VL7 VL8 EN 6 VL5 7 VL6 8 VL7 9 VL8 10 EN 1 2 3 4 5 6 7 8 9 10 5 of R34 NP 5 Figure 45. Quark Baseboard Schematic: Level Shifter C13 0.1UF VIO1_REF C51 10UF R38 4.7K NP R36 4.7K PCA9517 VCCA VCCB 8 SCLA SCLB 7 R35 C47 4.7NF 1 2 2 0R R81 C46 1UF VIO1_REF 3 R82 TO TNR CONNECTOR SDA_TNR SCL_TNR Level Shifter 4 (ICIP_TNR) (ICIN_TNR) (D_3_TNR) (D_2_TNR) (D_1_TNR) (INTB_2_TNR) (RSTB_1_TNR) (RSTB_2_TNR) (V_PGM) (D_O_TNR) (ICON_TNR) (ICOP_TNR) (INTB_1_TNR) B 1 11-10-2011_11:06 DWG NO QUARK BASEBOARD LEVEL SHIFTER 400 West Cesar Chavez Austin, Texas 78701 USA +1 512 416 8500 TITLE SIZE (SCL_TNR) (SDA_TNR) FROM MCU Silicon Laboratories, Inc. D14_MCU D13_MCU D12_MCU D11_MCU D10_MCU D3_MCU D4_MCU D5_MCU D6_MCU D7_MCU D8_MCU D9_MCU D2_MCU D1_MCU D0_MCU 1 1.0 A B Si477x-EVB Si477x-EVB Figure 46. Quark Baseboard Top Silkscreen Rev. 0.3 45 Si477x-EVB Figure 47. Quark Baseboard L1 Copper 46 Rev. 0.3 Si477x-EVB Figure 48. Quark Baseboard L2 Copper Rev. 0.3 47 Si477x-EVB Figure 49. Quark Baseboard L3 Copper 48 Rev. 0.3 Si477x-EVB Figure 50. Quark Baseboard L4 Copper Rev. 0.3 49 Si477x-EVB Figure 51. Quark Baseboard Bottom Silkscreen 50 Rev. 0.3 A RF RF RF 3 4 AM_LP2 AM_LP1 NP J37 RF RF C24 NP C11 NP GND T2 SILABS SL755TF01 1 5 NP J36 ESD_DIODE D1 L9 10NH C10 18PF RF RF C23 NP RF ESD_DIODE D3 RF FM_ANT RF C13 0.1UF 1NF C8 C26 NP 3 2 0 R4 RF L1 220NH C7 2.2NF 4 RF 1 2 3 4 5 6 7 8 9 10 FMVAR FMXIP FMXIN GNDRF RFREG FMO FMI WXI AMIW AMIL 3.2x2.5 U1 SI477X 30 29 28 27 26 25 24 23 22 21 INTB SCL SDA RSTB VD XOUT DCLK DFS DOUT QOUT IOUT IQFS IQCLK VIO2 DBYP C3 2.2NF C20 10UF CONN1X19 J1 9 A0 A1 4 DOUT DFS DCLK C4 2.2NF SCALE 2 16 Figure 52. Module Schematic 3 ED BELL DRAWN BY Silicon Laboratories Confidential: Disclosure under NDA only. C25 NP RF C9 62PF GND_PAD 41 L2 47NH FM_ANT 1 6 AM_LP1 T1 1:1 11 40 39 38 37 36 35 34 33 32 31 FMAGC1 FMAGC2 GPIO1 GPIO2 DACREF XTAL1 XTAL2 ROUT LOUT VA 2 1 5 RF 7 NC NC RSTB SDA SCL INTB VIO1 VD 11 12 13 14 15 16 17 18 19 20 AM_LP2 3 Rev. 0.3 4 B C22 NP 8 L3 150NH 12 C2 0.1UF 13 C1 100PF 10 VA 14 37.209375MHZ X1 15 C6 10UF 6 2 SHEET 1 R7 47K R6 47K C21 2.2NF C5 2.2NF of 1 ROUT LOUT OPTIONAL AUDIO OUTPUT FILTER R5 2.2K 0R 0R R2 R3 2.2K R1 18 3 19 4 +5V 3 F2 C12 0.1UF 4 B SIZE TITLE 2 C14 22UF F4 1 09-02-2012_11:09 DWG NO SI477x Module 400 West Cesar Chavez Austin, Texas 78701 USA +1 512 416 8500 1 NC GND VIN VOUT U4 AMS1117_3_3 Silicon Laboratories, Inc. F1 1 VA 1.0 REV VD A B Si477x-EVB 7.3. Si4770 Module Rev1.0 51 17 Figure 53. Module Top Silkscreen Si477x-EVB 52 Rev. 0.3 Si477x-EVB Figure 54. Module L1 Copper Rev. 0.3 53 Si477x-EVB Figure 55. Module L2 Copper Figure 56. Module L3 Copper 54 Rev. 0.3 Si477x-EVB Figure 57. Module L4 Copper Rev. 0.3 55 AM_LOOP JP? J? NP SMA_EDGE J? AM_ANT SMA_EDGE J2 FM_ANT 4 NP J? 0 J? 3 2 AM_LP1 AM_LP2 1 FM_ANT J1 CONN1X19 3 Rev. 0.3 19 17 11 10 9 SERGIO C. DRAWN BY RSTB_1 SDA SCL INTB_1 DOUT DFS DCLK 0 0 R3 R4 0 R5 0 R6 J? NP ID_EEPROM_SDA SCALE RSTB_1_TNR SDA_TNR SCL_TNR 0 R? 0 R? 0 R? 0 R19 0 R18 2 3 2 1 U1 1 v_3V3_BB SHEET A1 4 A05 VCC6 DOUT_TNR DFS_TNR DCLK_TNR LOUT_TNR ROUT_TNR SDA 34LC02 GND SCL VA_TNR INTB_1_TNR LOUT ROUT 0 J? Ext_supply ID_EEPROM_SCK JP1 2 Figure 58. Interposer Schematic 3 18 56 A B 4 of 1 C1 0.1uF 51 ID_EEPROM_SDA 7 5 3 1 6 4 2 B SIZE 1 10-02-2012_15:50 DWG NO 1.0 REV SI477X MODULE INTERPOSER TITLE 400 West Cesar Chavez Austin, Texas 78701 USA +1 512 416 8500 Silicon Laboratories, Inc. ID_EEPROM_SCK 9 8 11 13 SDA_TNR INTB_1_TNR DFS_TNR LOUT_TNR 10 12 14 15 17 18 16 19 21 23 20 22 25 27 24 26 29 31 32 28 33 34 30 35 37 36 38 39 41 40 43 42 45 47 44 46 48 49 53 52 50 55 54 57 59 56 58 60 J3 CONN_SFM_SM 1 A B Si477x-EVB 7.4. Si477x Interposer Rev 1.0 16 15 14 13 12 8 7 6 5 4 Si477x-EVB Figure 59. Interposer Top Silkscreen Rev. 0.3 57 Si477x-EVB Figure 60. Interposer L1 Copper 58 Rev. 0.3 Si477x-EVB Figure 61. Interposer L2 Copper Rev. 0.3 59 Si477x-EVB DOCUMENT CHANGE LIST: Revision 0.1 to Revision 0.2 Converted document to Quark Baseboard. Revision 0.2 to Revision 0.3 Added 60 support for the Si4770Module-A-EVB. Rev. 0.3 Si477x-EVB NOTES: Rev. 0.3 61 Si477x-EVB CONTACT INFORMATION Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Please visit the Silicon Labs Technical Support web page: https://www.silabs.com/support/pages/contacttechnicalsupport.aspx and register to submit a technical support request. The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. 62 Rev. 0.3