Mounting rail support Support block TSTW, TST Material thickness 1.8 mm Mounting bases Support block for TS 15, TS 32, TS 35 and busbars Mounting bases for TS 32 and TS 35 MOFU TSTW SH 1 for TS 15 FM SH 2 for TS 32, TS 35 TSTW MB TST The SH 1 and SH 2 support blocks enable construction of insulated mounting rails. The TST mounting rail support allows rails to be fitted into frames or above a cut-out. This design has an M5 or M6 thread (not shown). The sliding nut for TS 32 mounting rails has 2 tapped holes for M 3 + M 5 / M 6 + M 4 / M 5 + M 3 screws. It is used to fix components which cannot be directly mounted on the TS 32 and, in particular, to accept the smaller TS 15 “top-hat” rail. In this way, for example, small terminals can first be mounted on the TS 15 and this rail can then be mounted on the TS 32 with the aid of the sliding nut together with the terminals. Weidmüller offers hexagon socket fixing screws for the mounting rail supports with a particularly low head allowing terminals also to be fitted above the screw. SH 2 Type Cat. No. Qty. TSTW (M 5) TSTW (M 6) TSTW ø 4.3 TST (M 6) TST (M 5) TSTW (M 5), zinc-plated Fixing screw FKSC M 5x8 ø 9 hexagon socket SW 2.5 FKSC M 6x8 ø 9 hexagon socket SW 3 FKSC M 6x12 ø 9 hexagon socket SW 3 0178100000 0164000000 1610110000 0101700000 1286600000 1779100000 10 10 10 10 10 10 0295900000 50 0642600000 50 0353500000 50 Type Cat. No. SH 1 for TS 15 0299860000 in PA (thermoplastics) compl. SH 1 Base 0401460000 SH 1 Bracket 0635960000 Qty. 20 Type SH 2 for TS 32/35 in KrG (thermosetting) Qty. 10 Cat. No. 0494920000 Mounting bases are used to fix components onto mounting rails. Weidmüller offers a polyamide mounting base and a steel snap-on base for the TS 35 mounting rail. The FM 4 snap on base fits all “top-hat” mounting rails. The PA mounting base fits the TS 35 x 7.5 and the TS 35 x 15 slotted rails. 20 500 Type Cat. No. Qty. FM 4 (M 4) for TS 35 FM 5 (M 5) for TS 35 FM 6 (M 6) for TS 35 FM (Ø 4.2) for TS 35 MOFU mounting foot PA orange for TS 35 x 7.5 u. 35 x 15 gel. 0687900000 0636800000 0636900000 1724580000 0646260000 with bore 0495660000 without bore MB 3/5 (cream) 0503500000 with thread M 3 and M 5, for TS 32 MB 6/4 (grey) 0334900000 with thread M 6 and M 4, for TS 32 MB 5/3 (black) 0553400000 with thread M 5 and M 3, for TS 32 40 40 40 40 20 20 20 20 20 261 Accessories TSTW mounting rail supports allow for sloped fitting of mounting rails at an angle of 35°. Three designs are available with M5, M6 threads or with a bore of Ø 4.3 mm.