MX23C4100 4M-BIT [512K x 8/256K x 16] CMOS MASK ROM FEATURES • Switchable organization - 512K x 8 (byte mode) - 256K x 16 (word mode) • Single +5V power supply • Fast access time:100/120/150/200ns • • • • • Totally static operation Completely TTL compatible Operating current: 60mA Standby current: 100uA Package - 40 pin DIP (600 mil) - 40 pin SOP GENERAL DESCRIPTION The MX23C4100 is a 5V only, 4M-bit, Read Only Memory. It is organized as 512Kx8 bits (byte mode) or as 256Kx16 bit (word mode) depending on BYTE (pin 31) voltage level. MX23C4100 has a static standby mode, and has an access time of 100/120/150/200ns. It is designed to be compatible with all microprocessors and similar applications in which high performance, large bit storage and simple interfacing are important design considerations. MX23C4100 offers automatic power-down, with powerdown controlled by the chip enable (CE/CE) input. When CE/CE is not selected, the device automatically powers down and remains in a low-power standby mode as long as CE/CE stays in the unselected mode. The OE/OE input as well as CE/OE input may be programmed active Low. BLOCK DIAGRAM PIN CONFIGURATION CE/CE OE/OE 40 PDIP/SOP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MX23C4100 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE/CE VSS OE/OE Q0 Q8 Q1 Q9 Q2 Q10 Q3 Q11 CONTROL LOGIC BYTE Q15/A-1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 A8 A9 A10 A11 A12 A13 A14 A15 A16 BYTE VSS Q15/A-1 Q7 Q14 Q6 Q13 Q5 Q12 Q4 VCC . . A0~A17 ADDRESS INPUTS Y-DECODER . Q0~Q14 Y-DECODER . . . . . . OUTPUT BUFFERS X-DECODER . . . . . . 4M BIT ROM ARRAY . VCC VSS PIN DESCRIPTION Symbol A0~A17 Q0~Q14 CE/CE OE/OE BYTE Q15/A-1 VCC VSS P/N:PM0136 Pin Function Address Input Data Output Chip Enable Input Output Enable Input Word/Byte Selection Q15(Word mode)/LSB address(Byte mode) Power Supply Pin (+5V) Ground Pin REV. 3.4, OCT. 17, 2000 1 MX23C4100 TRUTH TABLE OF BYTE FUNCTION BYTE MODE (BYTE=VSS) CE OE/OE D15/A-1 H X X L L/H X L H/L A-1 input MODE Non selected Non selected Selected D0-D7 High Z High Z DOUT SUPPLY CURRENT Standby (ICC2) Operating (ICC1) Operating (ICC1) NOTE 1 1 1 WORD MODE (BYTE=VCC) CE OE/OE D15/A-1 H X High Z L L/H High Z L H/L DOUT MODE Non selected Non selected Selected D0-D7 High Z High Z DOUT SUPPLY CURRENT Standby (ICC2) Operating (ICC1) Operating (ICC1) NOTE 1 1 1 NOTE1:X=H or L ABSOLUTE MAXIMUM RATINGS* RATING Ambient Operating Temperature Storage Temperature Applied Input Voltage Applied Output Voltage VCC to Ground Potential Power Dissipation *Note: Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended period may affect reliability. VALUE 0°C to 70°C -65°C to 125°C -0.5V to 7.0V -0.5V to 7.0V -0.5V to 7.0V 1.0W DC CHARACTERISTICS (Ta = 0°C ~ 70°C, VCC = 5V±10%) Item Output High Voltage Output Low Voltage Input High Voltage Input Low Voltage Input Leakage Current Output Leakage Current Power-Down Supply Current Standby Supply Current Operating Supply Current Symbol VOH VOL VIH VIL ILI ILO ICC3 ICC2 ICC1 MIN. 2.4V 2.2V -0.3V - MAX. 0.4V VCC+0.3V 0.8V 10uA 10uA 100uA 1.0mA 60mA P/N:PM0136 Conditions IOH = -1.0mA IOL = 2.1mA VIN=0 to 5.5V VOUT=0 to 5.5V CE>VCC-0.2V CE = VIH Note 1 REV. 3.4, OCT. 17, 2000 2 MX23C4100 CAPACITANCE (Ta = 25°C, f=1.0MHz (Note 2)) Item Input Capacitance Output Capacitance Symbol CIN COUT MIN. - MAX. 10 10 UNIT pF pF Conditions VIN=0V VOUT=0V AC CHARACTERISTICS (Ta = 0°C ~ 70°C, VCC = 5V±10%) Item Symbol 23C4100-10 23C4100-12 23C4100-15 MX23C4100-20 MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. CONDITIONS Cycle Time tCYC 100ns - 120ns - 150ns - 200ns - Address Access Time tAA - 100ns - 120ns - 150ns - 200ns Output Hold Time After tOH 0ns - 0ns - 0ns - 0ns - Chip Enable Access Time tACE - 100ns - 120ns - 150ns - 200ns Output Enable/Chip Select tAOE - 50ns - 70ns - 80ns - 90ns tLZ 0ns - 0ns - 0ns - 0ns - Note 3 Note 4 Address Change Access Time Output Low Z Delay Output High Z Delay tHZ - 20ns - 70ns - 70ns - 70ns BYTE Access Time tBHA - 100ns - 120ns - 150ns - 200ns BYTE Output Hold Time tOHB 0ns - 0ns - 0ns - 0ns - BYTE Output Delay Time tBHZ - 70ns - 70ns - 70ns - 70ns BYTE Output Set Time tBLZ - 10ns 10ns - 10ns - 10ns - Note: 1. Measured with device selected at f=5 MHz and output unloaded. 2. This parameter is periodically sampled and is not 100% teseted. 3. Output low-impedance delay (tLA) is measured from CE going low. 4. Output high-impedance delay (tHZ) is measured from CE going high. AC Test Conditions Input Pulse Levels Input Rise and Fall Times Input Timing Level Output Timing Level Output Load 0.4V to 2.4V 10ns 1.5V 0.8V and 2.0V 1TLL+100pF P/N:PM0136 REV. 3.4, OCT. 17, 2000 3 MX23C4100 TIMING DIAGRAM PROPAGATION DELAY FROM ADDRESS (CE/OE=ACTIVE) tCYC ADDRESS INPUTS VALID ADDRESS tAA tOH DATA OUT VALID DATA PROPAGATION DELAY FROM CHIP ENABLE (ADDRESS VALID) CE tACE OE tAOE tLZ tHZ DATA OUT PROPAGATION DELAY FROM CHIP ENABLE (ADDRESS VALID) A-1 HIGH-Z HIGH-Z tOH tAA BYTE D0-D7 VALID DATA VALID DATA tBHA tOHB D15-D8 VALID DATA tBHZ tBLZ P/N:PM0136 REV. 3.4, OCT. 17, 2000 4 MX23C4100 ORDER INFORMATION Part No. Access Time Operating Current MAX. Standby Current MAX. Package MX23C4100PC-10 100ns 60mA 100uA 40 pin DIP MX23C4100PC-12 120ns 60mA 100uA 40 pin DIP MX23C4100PC-15 150ns 60mA 100uA 40 pin DIP MX23C4100PC-20 200ns 60mA 100uA 40 pin DIP P/N:PM0136 REV. 3.4, OCT. 17, 2000 5 MX23C4100 PACKAGE INFORMATION 40-PIN PLASTIC DIP (600 mil) ITEM MILLIMETERS INCHES A 52.54 max. 2.070 max. B 2.03 [REF] .080 [REF] C 2.54 [TP] .100 [TP] D .46 [Typ.] .018 [Typ.] E 48.22 1.900 F 1.52 [Typ.] .060 [Typ.] G 3.30±.25 .130±.010 H .51 [REF] .020 [REF] I 3.94±.25 1.55±.010 J 5.33 max. .210 max. K 15.22±.25 .600±.010 L 13.97±.25 .550±.010 F M .25 [Typ.] .010 [Typ.] D 21 40 1 20 A K L C I J H G B 0~15¡ M E NOTE: Each lead centerline is located within .25 mm[.01 inch] of its true position [TP] at maximum material condition. 40-PIN PLASTIC SOP ITEM MILLIMETERS INCHES A 26.16 max. 1.030 max. B 1.00 [REF] .038 [REF] C 1.27 [TP] .050 [TP] D .43 [Typ.] .017 [Typ.] E .102 min. .004 min. F 2.54 max. .100 max. G 2.24±.05 .088±.002 H 14.22±.08 .560±.007 I 11.18±.12 .440±.005 J 1.52 .060 K .15 [Typ.] .006 [Typ.] L .79 .031 40 21 1 20 A H I G J F K E NOTE: Each lead centerline is located within .25 mm[.01 inch] of its true position [TP] at maximum material condition. D C P/N:PM0136 B L REV. 3.4, OCT. 17, 2000 6 MX23C4100 REVISION HISTORY REVISION 3.3 3.4 DESCRIPTION PAGE AC CHARACTERISTICS tOH 10ns-->0ns P3 Modify MX23C4100-10 AC Characteristics:tAOE:60ns-->50ns(max.) P3 tHZ:70ns-->20ns(max.) P3 P/N:PM0136 DATE JAN/29/1999 OCT/17/2000 REV. 3.4, OCT. 17, 2000 7 MX23C4100 MACRONIX INTERNATIONAL CO., LTD. HEADQUARTERS: TEL:+886-3-578-6688 FAX:+886-3-563-2888 EUROPE OFFICE: TEL:+32-2-456-8020 FAX:+32-2-456-8021 JAPAN OFFICE: TEL:+81-44-246-9100 FAX:+81-44-246-9105 SINGAPORE OFFICE: TEL:+65-348-8385 FAX:+65-348-8096 TAIPEI OFFICE: TEL:+886-2-509-3300 FAX:+886-2-509-2200 MACRONIX AMERICA, INC. TEL:+1-408-453-8088 FAX:+1-408-453-8488 CHICAGO OFFICE: TEL:+1-847-963-1900 FAX:+1-847-963-1909 http : //www.macronix.com MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 8